Small businesses-ESW-520-48P-K9

Similar Questions

• ESW-520-24 p not able to connect to a Catalyst 3560 G + compatible with SPA942?

  Hi all

  a customer bought an ESW-520-24 p for use in a VoIP project. Today we had difficulties to connect to a switch of 3650 G of catalyst; We tried to set the port to the trunk, general, customer and access and changed all sorts of settings VLAN on the 3560G switch nothing helps: the switches just interconnection used. While sniffing, we saw that the ARP requests are unresponsive even, if something is at a low level, no doubt with VLAN-ing.

  Someone at - it an idea if these switches must be connected between them and if so, what do I do?

  On the other hand; voice turns on VLANS separated and the customer will use SPA942 phones that have an internal switch that allows a PC to connect. I used this call successfully with the Catalyst Express switches and I didn't have to do anything for VLAN-ing, it worked 'out of the box. Can anyone confirm that these phones work with switches for small businesses as well?

  THX!

  Bart

  Hi Bart,.

  I quickly set up the simulation.  It took me more time to write this that actually do the work.

  I grabbed my handy Cisco 3560 catalyst switch.  I plugged port FastEthernet 23 plugged into my UC520.  My Uc520 is my voice system and the DHCP server.

  I have the 24 FastEthernet port connected to my Cisco 3560 in my ESW540 - 24 p.  On 3 of my ESW540 switch port - 24 p, I plugged a phone SPA962...

  I guess that my simulation is close enough to your hardware.  The configuration should be the same I guess.

  Here is the configuration of my Cisco 3560 switch;

  interface FastEthernet0/23

  switchport trunk encapsulation dot1q

  switchport autostate exclude

  switchport mode trunk

  !

  interface FastEthernet0/24

  switchport trunk encapsulation dot1q

  switchport autostate exclude

  switchport mode trunk

  interface Vlan1

  192.168.10.3 IP address 255.255.255.0

  !

  interface Vlan100 (VLAN100 ends on my UC520 and has the DHCP scope)

  no ip address

  !

  interface Vlan200

  no ip address

  !

  Check that the tree covering weight is not blocking the ports of uplink with the command show spanning tree. I ask you to try what I must admit that this uplink to my UC520 was in a BLK State on the VLAN by default.  I HAD TO CORRECT.

  I plugged my phone SPA962 on my ESW switch, it lit.

  VLAN 100 as my voice VLAN, I had to set manually what VLAN the SPA phone will reside in.  Otherwise, it will try to retrieve a default IP VLAN.

  • I have manually by pressing the button (below the button of the envelope) on the phone in the SPA
  • Scroll down and select 'network '.
  • Scroll again option VLAN and select Edit.
  • I changed the setting to select Enable VLAN Yes.
  • Click the OK button.
  • I then scroll down to the option VLAN ID.
  • Choose the edit button to change the VLAN ID information
  • I register 100 to and selected OK.

  My phone has received an IP address from my 100 VLAN address 10.1.1.X.

  Fortunately, the ESW520 has a pretty good GUI, in which case you can add a new vlan and the trunk at all ports.

  Here's an example of how I added the vlan 200 to the ESW switch and started adding the Tagged ports switch ports.  I have to do all the ports where you need a VLAN.

  

  I then as seen below my new adds VLAN as a port Tagged to all ports of the switch.

  You can see from my screenshot below I was adding VLAN 200 to interface G2 as labeled interface.

  

  Don't forget NOT to SAVE YOUR CONFIGURATIONS ON BOTH THE 3560 and the ESW520

  

  hope this helps

  Best regards, Dave

• ESW-520-24 P has not managed the custom VIRTUAL local network traffic

  Hi all

  We recently bought a switch ESW-520-24 p to replace a CE500 end-of-life.  The facility where the switch is installed has access wireless connected to the VLAN 110 points.

  Course the ESW-520-24 p switch does not support VTP so none VLAN is to be propagated to it.  So I created 110 VLAN manually and ports assigned to him.  But the devices on ports communicate with anything.

  All ports are configured as access with 110 ports VLAN not identified.  The uplink is the g2 port which is in binding mode.

  Can someone please tell me what I can have configured wrong?

  Thank you

  -Steve

  Hi Steve,.

  If it is for UC500 installation, the default configuration on the ESW is normally perfect and the switch has to be turned on.

  Otherwise that looks like you have made the correct things.

  I guess VLAN1 is always present on the ESW switch, but excluded by access ports...

  All ports are not marked in VLAN110 except for the uplink, given that the packages of vlan tagged while waiting to switch receiver VLAN110 or unmarked packages?  (something to think quickly)

  But the result is if you are still in a stalemate, why not call the Small Business Support Center, the switch is probably still under warranty and telephone support.

  http://www.Cisco.com/en/us/support/tsd_cisco_small_business_support_center_contacts.html

  Best regards, Dave

• Restrictions on the HW HP (small businesses) to license reuse laptop components?

  Restrictions on the HW HP (small businesses) to license reuse laptop components?
  
  I realize that it is illegal to use a part of the (OEM) software that was distributed with the renovated nw8440 Mobile Pro HP workstation (laptop HP Compaq small business) I bought (HP direct) on a different computer (that software provided with).
  
  My question concerns well hardware components (HDD, keyboard, memory modules, speakers, mouse, etc.) accompanying.
  Specifically, is it legal for me to use these hardware components on a different computer (that the software provided with), or even to sell it, give it, or Dispose (separately from the HP computer system it is come with)?
  
  The reason why I ask this is that among the license agreements supplied with the system says something like:

  • The initial user of the product can perform the unique transfer of the product to another end user. ... The transfer may not be an indirect transfer, such as a consignment.

  and I am his retirement that computer (Windows XP) and am not familiar with these license terms.
  
  I just started to use his hard drive in a desktop computer more old we which hard drive has failed.
  
  I think that should be OK license-wise, but it made me wonder what restrictions, if any, I might have on other future uses of this type of material.
  
  Thank you.
  
  -RJ, USA
  
  PS - Please, forgive me if this isn't the right place to ask this question. I didn't know where to ask it.

  RJ.

  You can sell parts or hole unit.

  With no HARD disk without problem.

  REO

• Advice needed on Optimal routing device specific and small businesses

  Hello
  I have worked mainly in the system of security for several years now, but has been approached by my father to help with a project of home office he seeks to complete.  Currently, he runs a Web server of its headquarters which is connected to one of the ports on an old Linksys router.  It works also all the home devices (Smart TV, laptops, phones, etc.) through a port other than same router.  The goal of the project is to separate these two networks (home or office) of bandwidth and security purposes.  He attempted to contact his ISP for a second connection installed, but I guess that their policy allows a connection must be installed in a single House.
  My original idea was to implement secondary interfaces on external port that goes to the ISP but the current Linksys router is so old and only accessible via HTTP/HTTPS is not able to support the secondary interfaces or VLANS.  I expect some tips on the different options on the routers for individuals and small businesses that support interfaces and which would achieve the objective of this project.  I would prefer something that uses Cisco IOS and that can be managed from a command line, but am open to all options.  Any help would be greatly appreciated!

  Hello

  Connect a layer 3 Switch Cisco to the router. You can create a VLAN on the switch, create all the lass on the switch, and then route the switch router.

  http://www.Cisco.com/c/en/us/products/switches/small-business-300-series...

  I'm not employed by CISCO, but hope this helps.

  Have a good Christmas.

• ESW 520 8 ports - firmware update

  Hello

  We have an ESW 520 8 ports currently on the 2.1.1.19 firmware version (version of boot 1.0.0.07, VID V01) - serial number CBT15100AN2

  The latest version of the firmware is 2.1.1.21, that we have downloaded and through the Maintenance, update the software, via HTTP, performed an upgrade to this version - upgrade appears to complete, will connect to see success but when we restart the switch it always shows as 2.1.1.19. Very strange!

  Can someone advise please how to get the upgrade to successfully apply?

  Sincere greetings,

  Dale.

  Hi Dale,

  Have you changed the active firmware image to the new version before rebooting? (Maintenance-> file management-> Image Active)

  Best,

  David

  Please evaluate the useful messages and identify the right answers.

• On the Maximum of Source Ports on a Port Destination ESW 520 24 P

  The ESW 520 24 P does support mirrored 20 Ports traffic at the Port of Destination 1?

  Hi Andy

  Without media ESW mirroring groups each of which can mirror 8 ports to a destination port.

  It is fine for normal problem determination purposes. I can guess your application.

  What about Dave

• ESW-520-24-K9 supperted SFP

  Hello

  I am interesting is ESW-520-24-K9 support GLC-LH-SM SFP switch?

  There is no information about it in the official record. Some guys there spoke it is supported and I am interesting if it's true?

  I hate the idea of mode single market 9um FPS on a multimodal 50 cable or fiber core 62.5th.

  I've never used, but I guess that if you run SM SFP fibre MM, there may be a way of packaging of cable to allow this coupling.

  Within Cisco, I saw the mention of the use of SM SFP on multimode. I am convinced by this application.

  I personally don't validate FPS of SM running on a cable mm. my colleagues may disagree.

  I look forward to any input to your application to other people on the community.

  What about Dave

• ESW 520 give priority to IP addresses

  I have a LAN with IP addresses for the computers and public, static IP for VoIP phones. They are a hosted VoIP provider, and I want to give priority to the public IPs from my ESW-520-48 per switch How I implemented that in this switch?

  I have no roles assigned on ports and no configuration of VLAN either. I had tried to separate the VLAN first, but eliminated this way. It is once again all VLAN 1 now on the switch. For some reason when I put in place of the 100 VLAN for voice, the voice stopped working on phones, but data were always very good.

  Hi netguy,.

  QOS in rewriting the DSCP (dissociated Services Code Point) address IP phone range by;

  1. create an ACL that specifies the range of IP addresses with mask reverse

  2. attach the ACL on a map of advanced class, then

  3. fix a plan of class to a table of QOS policy that is configured to set a new DSCP value

  4. attach a QOS policy on an interface

  5 but you have a default Advanced QOS configuration already in place, so that should be modified or deleted.

  It is difficult if you have never played with before advanced QOS or understand the latest five statements.

  I guess that your hosted IP phones have DSCP settings (dissociated Services Code Point) already placed on IP phones or the settings that you can set directly on each IP phone?

  If it is possible, why not just move the switch to the basic QOS mode and then say the switch to trust DSCP.

  Well, it's the best thing to do.

  

  

  Best regards, Dave

• ESW-520-8 p-K9 POE capabilities

  Can the ESW-520-8 p-K9 provide enough POE to take in charge 7 PVC2300 cameras?  If not, what are its limits?

  Hello

  The ESW 520 8 ports offers a maximum power of 15.4 to any 10/100 port; Total of 60W.

  The ESW 540 8 ports offers a maximum power of 15.4 to any port 10/100/1000; Total 123W.

  By the PVC2300 datasheet, each camera has a consumption of 10W.

  If you need 7 cameras supported, you can consider the 8-port ESW540. Another option is to power the cameras via the external power adapter, assuming that a power source is nearby.

  I hope this helps.

  Bert Wilhelm

  Solutions of the APW

  Austin, TX

• With Creative Cloud for small businesses, the number of users you get per license?

  We are seeking creative cloud and are interested in the "Complete" package for small businesses, but we don't know exactly how it works with licenses and users? How many users you get per license? Do we need 1 license per user?

  Hello

  The Adobe CC license is not specific to the user; It is specific to the Adobe Id, on which it was purchased.

  Adobe CC license can be activated on 2 machines using the same Adobe ID, but can be used only 1 at a time.

  Reference: licenses and terms of use | Adobe

  Visit the pricing and membership creative cloud plans | Adobe Creative Cloud for plans and prices.

  
  

  Kind regards

  Sheena

• What is the difference between individuals and small businesses?

  What is the difference between individuals and small businesses?

  Hi Nakrit,

  The individual plan provides only a single application license in your Adobe account.

  According to the individual plan, you have the right for 20 GB of cloud storage space.

  However, the business plan gives you an administration console where you can buy the multiple license.

  Under the business plan, each license offers 100 GB of cloud storage space.

  Pricing plans and creative Cloud membership | Adobe Creative Cloud

  Kind regards

  Sheena

• Cost of Photoshop for small businesses

  Hello

  I would like to know how much is the photoshop for small businesses? Maybe CS5 or CS6, I didn't care of version. In addition, I will add I mean Photoshop for a position - in the sense of on a single computer.

  I was looking for answers on this forum and on the Adobe homepage, but there is the same monthly plans...

  Kind regards

  GeoMorf

  CS5 is discontinued, but you can always buy CS6: Creative Suite 6

• VLAN 2 switch ESW - 520

  For the test I used 2 switch this name 'ESW X' and 'Y ESW '.

  I have 2 network that I named "Network A" and "Network B".

  I build a VLAN 2 for each network named Vlan 2 for network and Vlan 3 to network B, I do not use Vlan 1 because it is the default Vlan

  Configuration ESW X:

  port e1: access on UNTTAGGED Vlan 2 PORT

  port E2: access on UNTTAGGED Vlan 2 PORT

  E3 port: PORT of ACCESS on UNTTAGGED Vlan 3

  E4 port: PORT of ACCESS on UNTTAGGED Vlan 3

  G3 port: with 1 (default) UNTTAGGED Vlan TRUNK PORT and Vlan tagged WITH 2 and 3 to Vlan

  Configuration ESW Y:

  port e1: access on UNTTAGGED Vlan 2 PORT

  port E2: access on UNTTAGGED Vlan 2 PORT

  E3 port: PORT of ACCESS on UNTTAGGED Vlan 3

  E4 port: PORT of ACCESS on UNTTAGGED Vlan 3

  G3 port: with 1 (default) UNTTAGGED Vlan TRUNK PORT and Vlan tagged WITH 2 and 3 to Vlan

  I use for the test computer 2 with the same class IP address.

  Test result:

  Communication between ESW X e1 and e2 x ESW => OK

  Communication between ESW X e3 and e4 x ESW => OK

  Communication between ESW e1 and e2 ESW Y => OK

  Communication between ESW e3 and e4 ESW Y => OK

  Communication between e1 ESW X and Y of the ESW e1 or e2-online NOK

  Communication between e2 ESW X and Y of the ESW e1 or e2-online NOK

  Communication between e3 ESW X and Y of the ESW e3 or e4-online NOK

  Communication between e4 ESW X and Y of the ESW e3 or e4-online NOK

  Each Vlan cannot communicate with the switch, I think they have a problem in my configuration of vlan / port, can you help me.

  Hi, Thibaud,.

  Thank you for the purchase of the ESW switches.

  Just out of curiosity, you are using the latest firmware on your version of switch ESW 2.1.19

  But of course, you seem like you have a great understanding of Tagged and VLAN no tagged of you ad description... great stuff.

  I just tried your configuration, I can communicate between ESW540 - 24 p-switch and a SF300 - 48p.

  Sorry, I don't have two switches handy ESW. But it doesn't matter. Standards based Ethernet is I hope that some standards based on ethernet

  My configuration of vlan below for my ESW540 - 24 p and it works very well.

  I plugged just ports of the switch 24 between the two switches together, that's why the 24 port is labeled in each of the screenshots below.

  I really really doubt you would have a problem, unless there is something fundimental or basic you did for example do not save the configuration running on the boot configuration.  Obviously do not save the configuration before a power down will kill the configuration.

  (saved your configuration in each switch)

  

  

  Here is a copy of a part of my switch running configuration, which were a result of me playing with the ESW configuration utility.

  (Note that my switch has all Gigabit ethernet ports ;)

  serial interface ethernet g(1-2)

  switchport vlan trunk native 2

  output

  interface ethernet g24

  switchport trunk allowed vlan add 2

  output

  serial interface ethernet g(3-4)

  switchport vlan trunk native 3

  output

  interface ethernet g24

  switchport trunk allowed vlan add 3

  output

  If you still have questions, here's what URL to the Small Business Support Center contact, perhaps a new set of eyes can spot the problem.

  http://www.Cisco.com/en/us/support/tsd_cisco_small_business_support_center_contacts.html

  Best regards, Dave

• Small businesses of Microsoft Outlook 2000

  Seeking advice.  I click on the outlook icon.  Outlook opens briefly and then closes immediately.   Used Microsfift diagnosis.  Looked at the switches.  Also tried the repair icon small business office.  Can't get outlook to open.  Any suggestions?

  Seeking advice.  I click on the outlook icon.  Outlook opens briefly and then closes immediately.   Used Microsfift diagnosis.  Looked at the switches.  Also tried the repair icon small business office.  Can't get outlook to open.  Any suggestions?

  It's better if publish you in the Outlook section. Here is the link:
  http://social.answers.Microsoft.com/forums/en-us/category/OfficeOutlook

  Waiting to see if this can save your trip in the Outlook forum...

  Start button > searxh box, type outlook.exe /resetnavpane > press the Enter key.

  Note: there is a space between "outlook.exe" and ' / '.

  For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.