sound via DVI - D to HDMI

Similar Questions

• Sound of Lenovo A62 via dvi

  Hello everyone,

  I want to use a dvi cable to hdmi for graphic and audio transfer via dvi to TV. Is this possible?

  I have already installed realtek high def audio driver and amd suite software catalyst but no sound on dvi, only on the speakers.

  Any idea?

  Best regards, feberg

  This is not possible with the Integrated GPU. There are certain Nvidia graphics card that allows you to do. But none of the shipped Lenovo Nvidia graphics card has this ability.

• HP pavilion p6630f supports output via connector dvi - d to dvi - d to hdmi audio adapter?

  HP pavilion p6630f supports output via connector dvi - d to dvi - d to hdmi audio adapter?

  Hello

  The DVI does not support audio.  You must use a separate with the DVI cable audio cable. There are DVI cables that do not have an extra audio cable in the same sheath, but they are usually not sold in most retail stores.

  There are rumors on the net that ATI could have a special cable where some unused DVI pins were used to route the audio but that could also mean using an ATI video card. It would be a very strange configuration and not one I would recommend.

• Can I send sound to the new apple tv to airplay speakers and around things sound via HDMI to the projector?

  Can I send sound to the new apple tv to airplay speakers and around things sound via HDMI to the projector? My projector has HDMI but no audio output. Thank you.

  You can set the audio output to the airplay speakers in settings on Apple TV

• Re: Satellite A300-1MC - no sound via HDMI connection

  When I connect my Satellite A300-1MC on via connection receiver HDMI audio Yamaha in order to play music, no connection is possible, even without sign HDMI on the receiver is lit?
  any ideas?
  problem with the drivers or something else?

  This Toshiba document may be useful:

  + No sound via HDMI +.
  http://APS2.toshiba-tro.de/KB0/TSB8802F00000R01.htm

  The error is caused by the order of the pre-installed Intel display driver installation.
  The problem could be fixed by reinstalling the Intel Display Treibers V15.9.5.1502 or higher.

  Check it out!

• I tried to connect via / DVI to hdmi and it does not wrk

  If I have vga and dvi on my screen but only vga on my computer is - it say that I did not compatible computer to run hdmi to my screen?

  Hi lastace,

  If your vga port is blue, this means that it is a D - Sub connection.

  With D - Sub, you can buy a connector which can convert the output D - Sub to DVI, but unfortunately, not HDMI.

  So in your case, you can connect your monitor via D - Sub (VGA) or DVI but not HDMI unless you have a HDMI port your

  laptop. Sorry I couldn't give you good news.

  I hope this helps!

• No sound via hdmi

  Hello

  I have a hp dv9000 with hdmi output.  I signed up for Netflix and connected the laptop hdmi cable to our TV.  Use of IE, I started a film and the video is very good.  The sound of the film is coming through the speakers of the laptop, but not the tv.

  Curiously, the windows sound is coming through the tv speakers and not the laptop.

  How can I get the sound of the movie to play through the TV?

  Hello Bulverde,

  By default the Vista transmits no sound on HDMI output.  To change this to change the settings in the control panel.

  Note: This will turn off sound from speakers or normal audio output on the laptop.  To get that back, you will need to reverse this process.

  1. click on the button 'Start '.

  2. click on "Control Panel."

  3. 'Control Panel Home' click 'hardware and sound '.

  4. where it says "Sound" in green letters, there are three options below that are in blue, click on "manage Audio devices".

  5. This will bring up a window titled "Sound".

  6. on the tab 'Read' it has listed the sound options at your disposal. It should read "peripheral digital output (HDMI)" click on it.

  7. it should now check this option box.

  8. the sound should play through your HDMI connections to the TV.

  You can also see the article that will give you more information on this.

  http://support.Microsoft.com/kb/953500

  You can also watch the thread below in which another user had same issues and try different possible steps listed:

  http://social.answers.Microsoft.com/forums/en-us/vistamedia/thread/28691f82-610e-4F01-be2f-b2ced7cca645/

  Thank you

  Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think.

• I can't get sound to my tho TV hdmi cable

  I can't get sound to my tho TV hdmi cable

  vojkfojaojojgorjwojs

  Hi Alex,

  Try these steps and check the result.
  Step 1: Select the HDMI
  a. click on the button 'start '.
  b. click on 'control panel '.
  c. with the control to the "Control Panel Home" Panel, click on 'hardware and sound '.
  d. where it says 'Sound' in green letters, there are three options below that are in blue, click on "manage Audio devices.
  e. This will bring up a window titled "Sound".
  f. on the tab 'Read', he has listed the sound options at your disposal. It should read "peripheral digital output (HDMI)" click on it.
  g. There should now be a checkmark on this option.
  h. the sound should play through your HDMI connections to the TV.

  Note: This will stop sound from speakers or normal audio output on the laptop.  To get that back, you will need to reverse this process.

  Step 2: Download and install the driver card sound compatible Windows 7 either on the system or device manufacturer's website.

  See also, no sound via HDMI

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cannot get 2560 x 1440 on U2713HM via DVI - D of Latitude E7470

  I have a brand new Dell Latitude E7470 connected to a Dell E-Port Plus Advanced Port Replicator (model PR02X). I have the E-Port Plus, connected to 2 monitors - a brand new P2414H Dell via DisplayPort on Video 1 and a Dell U2713HM via DVI - D on Video 2 (see diagram below). Can I use two screens, but although the E7470 correctly identifies the U2713HM, it offers only as the highest resolution up to 1920 x 1200.
  According to the website of Dell and this forum, the U2713HM supports the complete resolution of 2560 x 1440 via DisplayPort * or * DVI - D (no HDMI), but even if it is connected to DVI - D, I can't put it in 2560 x 1440.
  Why is this and how to get the resolution full 2560 x 1440 via DVI - D link? As it is, it seems blurred and just awful.
  A little background extra. I have a setup of 3 monitor with the U2713HM in the middle and shared between the E7470 laptop and my office. I have my desktop connected to the U2713HM on the DisplayPort, so I can't use the E7470/E-Port Plus to the U2713HM DisplayPort. When I go to the U2713HM on the desktop on the DisplayPort, I get the full 2560 x 1440 resolution and it's fantastic.
  

  OK, no ports DVI on any Dell E-platforms will be higher than 1920 x 1200.

  Maximum resolution P2414H = 1920 x 1080
  Video of P2414H in ports = DP, DVI, VGA

  Maximum resolution of DP and DVI - D U2713HM = 2560 x 1440
  Video of U2713HM in ports = DP, VGA, DVI - D, HDMI

  The installer suggested =
  Docking station video 1 DVI out--> DVI to DVI cable--> DVI P2414H 1920 x 1080
  Video docking station 2 DP on--> cable of DP to DP---> U2713HM DP in 2560 x 1440
  Computer DVI out--> cable DVI to DVI--> U2713HM DVI in 2560 x 1440
  Exit desktop VGA--> VGA cable VGA--> Samsung 275 t VGA 1920 x 1080?

• Problem out 5.1 Surround sound via the TV to a Home Theater (Override sound formats supported?)

  Hi, I'm trying out a sound 5.1 on my Home Theater system via my TV via a digital output optical. So the video card (Asus EAH5450) is capable of up to 7.1 output, is connected via HDMI to my TV (a LG 47LH5000) which then returns sound via an optical digital output to my Home Theater 5.1 system (a LG HB965TZ). I have an Xbox 360 connected via HDMI to the TV and sound 5.1 is delivered perfectly to the correct speakers.

  The problem, in my view, is that the computer detects that it is connected to the TV that tells the PC there 2 speakers, so the sound of Windows 7 configuration menu displays just stereo and dolby digital.

  Is it possible to substitute the detection automatic that the supported formats and force the card to output 5.1 sound as I know, he is capable of?

  Thank you
  Martin

  Hello

  Try to follow the instructions to apply the sound card settings and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows7/sound-cards-frequently-asked-questions

• P6110y HP upgrade to DVI - D and HDMI video/graphic

  You will need to connect desktop to HDTV via DVI - D as a second monitor.  Constrained by simple VGA port ondesktop.  CURRENT EQUIPMENT: (1) PC is HP p6110y, Windows 7, 64-bit, a single VGA port, 250w power supply output;. (2) monitor is HP w2338h LCD with a 1920 x 1080 at 60 Hz optimal resolution;. (3) HDTV = Projection LCD Sony KF-41WE610, HD video via the input DVI - D or component @ 1080i, 720 p, 480 p and 480i.

  MY NAÏVE QUESTIONS: (1) what should I know about the graphics card, the power and features of installation for HP p6110y?  Any recommendation of brand/model for this PC, recognizing my immediate need is for watching movies online, clips and text high resolution?  [NOTE: I'm not a gamer, just seeking to exploit the internet for work and entertainment content.]

  You are the very welcome, Dan.

  Looking forward to reading about your video card update.

  Kind regards

  Paul

• TC-105 acre, computer and monitor S230HL. No sound via the monitor. Can get with headphones

  TC-105 acre, computer and monitor S230HL. No sound via the monitor. Can get with headphones strangely. Do I need speakers or is it a parameter. Have tried different audio settings with no luck.

  on Acer website:

  http://us.Acer.com/AC/en/us/content/model/UM.VS0AA.A02

  No speakers on this model.

• I can't hear any sound when you play a HDMI video uploaded to youtube, plays very well while on youtube but will not play sound from my hard drive after the use of realplayer download

  I can't hear any sound when you play a HDMI video uploaded to youtube, plays very well while on youtube but will not play sound from my hard drive after using the lplayer rea download

  Hello

  We will try to download different video using different downloader (other than RealPlayer) and see if the problem still persists.

• Satellite P300: no sound via HDMI on HDTV

  Hi all

  I get video but no sound when I connect my laptop to my Toshiba HD TV.
  I looked at the settings, but they seem to be ok.

  Any help would be great.

  You must follow these steps if you connect a HD TV to the laptop:

  1. fix a TV to the laptop via HDMI, while both units are in a * "power" off * State.
  2. turn on your TV first, then the laptop.
  3. laptop should automatically detect the HDMI connection and video output can be seen via HDMI to the TV.
  4 launch Sound (start (Windows logo)-> Control Panel-> hardware and sound-> Sound)
  5. on the playback tab, select "Peripheral digital output (S/PDIF)" and click on "Set as default"
  6. click on 'Apply' then 'OK' to close his
  7. the sounds played on the l should now also be heard on the TV (keys Fn + ESC or the volume dial can be used to cut the sound to the computer)

  _Please Note: _
  1. peripheral digital output (S/PDIF) installation default through Volume mixer does not output digital audio via HDMI.
  2 HD DVD-video can only be displayed on the LCD of the computer bulletin board or on a television connected to the output of HDMI port. HD DVD Video cannot be displayed on televisions connected to the S-Video port or an external display connected to the RGB connector.

  Hope this helps

• Qosmio G30: No sound via HDMI after installation of Vista

  Hello..
  After installing Vista on my G30 HD DVD I have no sound on any application via a HDMI cable. Sound works fine on the internal speakers. He also worked very well under XP. Can anyone help?

  Hello

  The noise does not appear on the external HD TV which was connected to the Qosmio G30 via an HDMI cable. But the internal speakers work. Am I wrong?

  Buddy you check the sound options in the control panel?
  Check if all controls are set at a higher level and are not disabled!