SPA9000/SPA941 Conference issue

Similar Questions

• SPA9000 numbering issues.

  Hello world

  I am installing a SPA9000 / SPA400 phone solution with 6 SPA942 extensions.  I got all the boxes, connected to the network and I can set up the units via the wizard or the web interface.  My problem is that for some reason that I can't compose between extensions (my extensions are 101 to 106).  I got this job all previously to the title of the version 5 firmware, but I've updated the SPA9000 to ensure that I get 6 extensions to work.  I have factory reset everything several times and configured it according to the guidelines from the Wizard (2.1.0.0) following the PDF document Wizard.  If I pick up the phone and try to dial another extension, as soon as I press the first digit (1 in this case), he stands up and says invalid number.  To me, it seems that the Dial Plan Wizard is not correct.

  The default dial plan generated looks like this:

  (<*97:vmm>| [0000], 000 S 0. [0000], 106S 0. [0000] 1 [38] xxxxxxxxS0 | [0000], 13 [1-9] xxxS0 | [0000] 1 [9] xxxxxxxxS0 | [0000], 0 [23478] xxxxxxxxS0 | xxxxxxxS0 [0000], [2-9] | ([0000], 0011xxx.)

  Having said all that I can go to the corporate directory on the phone and there is an entry for the configured item numbers and if I select I get the same result, but at the end of the directory entered to phone 1, phone 2, etc. (names I assigned for phones), and these choices actually compose the other extensions.  Very strange

  I'm setting up the system for use in Australia.

  Any suggestions?

  check the dial on the phones themselves plan and ensure that they have the same as on the SPA9000 dial plan. announced just a xx. at the end of the dial plan syntax so that you can dial any number as well.

• Palm Pre cannot do timed Pause or break closes in a dial string. (e.g. online access to the Conference; Access voicemail; NBR of 10 digits, pause, spindle)

  I called Palm support who told me to use commas for 1 second pauses, even if this was not documented any where ever I could find. After thanking them and hanging up I tried. It does not work. Commas are deleted as soon as you click DONE to save the changes. I called Palm, with the same number of tickets, and they have reproduced the problem. 18 hours later (as promised), they called back to say there is no work around, but software engineering focuses on this offer in a future update.

  Now, I can not access voicemail (1) Office, with House (2) answering machine, voice conference lines (4) (3) cable phone that requires entry of a PIN; (5) launching my own conference for others to compose in bridge.

  Those are often used while I'm driving (auto speed) 1 access key to an integrated chain of 24 characters with 2 breaks is a huge requirement for safety and convenience.

  This will be a major issue for the business users and the fix should be in the next push of software. This cannot be considered a new feature request, it's a bug. Even in charge think commas should work. This seems to be a mistake to design and test.

  [Later note: Although there is an open ticket to Palm, I have also posted here in the hope others would chime if this feature is important to them.] Visibility + Votes = pressure + interest = fixed sooner?  ]

  Features of technology of the Palm Pre are works perfectly for me. I don't know how something this basis exceeded the testers.

  Have you tried 'P' for break?

  Just curious...

• NEITHER sessions only weekly: what is the 'conference' without sessions?

  Here's what it says on the site OR of the week:

  Sessions going only: Includes access to keynotes, sessions and expo booths only.

  Full of conference: Includes three-day Conference and exhibition admission, meals,
  exhibition of receptions and parties.

  Unless the 'Conférence' and 'sessions' are used interchangeably, it seems that the part of the 'Conference' described in the full Conference is more than just meetings. What is the Conference include other than sessions? I have seen that there will be hands-on workshops, but I don't know if these count sessions or not.

  Sorry if this sounds like an incredibly nit-picky issue. I just clarification on that.

  The extra stuff the full Conference are lunch and dinner/activities/parties.  No technical information is presented in these - just everyone eats, drinks and fun.

  Hands-on workshops sessions are considered.

  Bruce

• SPA9000 Setup problem with FXS ports

  SPA9000 PBX, configured with two VoIP providers implemented voice-> 1/2 line parameters. A telephone is connected to the FXS 1 (or 2 FXS) port and able to choose the right VoIP provider when making outgoing calls.

  SPA9000 question is that once the outgoing call is established, does not meet the other numbers composed for the extension of the called party number. Same question when you dial a number where voice prompt responds to the call, offering the choice of activities, to choose the specific number. None of the input selection works as nothing is written on the dial.

  Located in the Canada. VoIP providers: freephoneline.ca & callcentric.com

  SPA9000 Setup:

  Software version: 6.1.5; Hardware version: 1.0.5(a)

  Voice-> SIP-> PBX parameters-> call routing rule: (<:L1>9xx. |) <:L2>8xx.)

  Voice-> SIP-> settings-> telephone numbering Plan PBX phone: ([89], S 11, 0 [3469] |) [89] 1 [2-9] xxxxxxxxxS0 | [89], 011xx. | ([89], xx.)
  Voice-> FXS 1 / 2-> Dial Plan: ([89], S 11, 0 [3469] |) [89] 1 [2-9] xxxxxxxxxS0 | [89], 011xx. | ([89], xx.)

  Voice-> line 1-> Dial Plan: (<>xx.) [Smiley here shows insetad of: and >]
  Voice-> 2-> Dial Plan line: (<>xx.) [Smiley here shows insetad of: and >]

  Voice-> regional-> ringtones of appellate courts:
  Tone: 350@-19,440@-19;10(*/0/1+2)
  Second tone: 420@-19,520@-19;10(*/0/1+2)
  Outside the tone: 420@-16;10(*/0/1)
  Prompt tone: 520@-19,620@-19;10(*/0/1+2)
  Busy signal: 480@-19,620@-19;10(.5/.5/1+2)
  Reorder tone: 480@-19,620@-19;10(.25/.25/1+2)
  Off-hook warning: 480@-10,620@0;10(.125/.125/1+2)
  Back ringtone: 440@-19,480@-19;* (4/2/1 + 2)
  Confirm tone: 600@-16;1(.25/.25/1)
  SIT1 Tone: 985@-16,1428@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
  T2is Tone: 914@-16,1371@-16,1777@-16;20(.274/0/1,.274/0/2,.380/0/3,0/4/0)
  SIT3 Tone: 914@-16,1371@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
  SIT4 Tone: 985@-16,1371@-16,1777@-16;20(.380/0/1,.274/0/2,.380/0/3,0/4/0)
  Tone MWI: 350@-19,440@-19;2(.1/.1/1+2);10(*/0/1+2)
  Cfwd-tonalite: 350@-19,440@-19;2(.2/.2/1+2);10(*/0/1+2)
  Holding tone: 600@-19;*(.1/.1/1,.1/.1/1,.1/9.5/1)
  Tone of the Conference: 350@-19;20(.1/.1/1,.1/9.7/1)
  Ensure the Indication of the ringtone: 397@-19,507@-19;15(0/2/0,.2/.1/1,.1/2.1/2)
  Featured call tone: 350@-16;*(.1/.1/1)

  Hi @sglumac, it seems that your SPA9000 is a Cisco product. Please repost this at this link: https://supportforums.cisco.com/ for solutions.

• Need help with MWI for voice mail on SIP with SPA9000

  I can't get my MWI to work with my answering machine SIP.  I have:

  SPA9000

  1 SPA962

  1 SPA941

  My ITSP is Mconnect and my SIP phone number is configured for line 1 on the SPA9000.

  I am using their voicemail.  I want the MWI light only on my phone SPA962.  I packed an id 1101 for this phone's mailbox.  I can press the message button and connect to my voicemail, but I don't get a MWI when I have new voicemail.

  Here are the settings for voicemail, I SPA9000 > voice > line 1:

  Mailbox repository URL: mysiptelephonenumber@line1proxy

  URL for mailbox management: even the form of mailbox repository URL

  Mailbox subscribe URL: it is indifferent to what I put in this context, nothing works.

  MConnect gave me a few things to try, but they do not work either.

  Any help is greatly appreciated.

  Marti

  I googled my question and found the answer here on this forum in a post from last year!  My MWI now works as it should when I have voice mail on my SIP line.

  Here is the link to the post on this forum where I found the answer:

  http://forums.linksysbycisco.com/Linksys/board/message?board.ID=VoIP_Phones&thread.ID=3899

  Also be sure to enter the URL for the mailbox to subscribe, filing and management.

  Mine are my number of mailbox @ the proxy for the line that my SIP line is activated, which is Line 1

  Marti

• Registering the PAP2T with a SPA9000

  I'm trying to get a PAP2T to save with a SPA9000.

  The PAP2T says "Unable to connect to the login server" - a network trace shows that the SPA9000 returns 404 not found when the PAP2T tries to register.

  I created the following on the PAP2T

  Port SIP LINE1: 45010

  LINE1 Proxy: : 7070

  (SPA9000 defined 7070 as its Proxy listening port to)

  LINE1 user ID: 2501 (post number to use)

  (I tried affecting and not a password as well)

  But other that that, I did not put anthing else - "Use outgoing proxy has the value no. I use 5.1.1 firmware.

  Everything is on the same local network and seems to work other than...

  There seems to be no instruction on the connection of these two products together.

  Any body got any ideas.

  See you soon

  s

  Hi, I have the SPA9000 like my PBX, the new Gigaset phones for users and the PAP2T to connect the phone voip either (polycom Conference phones)

  The entire Setup is on the same local network, but behind a NAT/Firewall with DHCP from the NAT/Firewall.

  The SPA9000 is connected to the network via the WAN port

  I'll also VOIP and the PAP2T phones to use the SPA9000 as its SIP provider.

  I've now had the PAP2T works with the SPA9000! If it can help someone else, here is my configuration:

  I have a password set on the SPA9000 (defined by going to tab SIP on the SPA9000 (since the connection admin/advanced mode) and password phone Ext:-which is below).

  NOTE: You need not perhaps not a password - I do it because I'm also using using Gigaset VOIP phones that does not connect to the SPA9000 without password.

  I put on the PAP2T (using the web interface of the PAP2T) from the Line1 TAB

  (a) sip port is not used any other phone (unique)

  (b) proxy in the ip address and the port of my SPA9000 (e.g. 192.168.1.2:6060). You must set values based on the configuration of the SPA9000

  (c) the value that identifies the extension no, I wanted the phone to be on (e.g. 2503)

  (d) to set the password to be the same as the SPA9000

  use Auth ID value e) YES

  (f) set the Auth ID on the extension, I wanted the phone to be on (e.g. 2503)

  (g) line enabled to yes!

  And it works!

  Thanxs

  s

• Conductor / vTPS - special Conference multi-party merger fails

  Hi all.

  I installed this same scenario several times for other clients without previous problem.

  When you try to merge the 3rd participant VC, the merge fails. The message "Unable to merge" OSD endpoint

  Conductor dialed says"disconnected B2BUA call on penetration saying"Timed out waiting for the acknowledgement.

  The current environment is:

  Conductor: 4.2

  Virtual GST: 4.3

  CUCM: 10.5.2

  MX700 & MX300: S/W CE8.2.1

  Newspapers of a conductor has the below

  016 08 - 08 T 12: 59:33.425 + 10:00 conferencefactory.controller: Level = "INFO" Event = 'a conference has been removed." Conference_name = "0010351100040x5c57e406b51ad5c4" Conference_unique_identifier = "c9c8420c47ef8d873abbf138adbf3e5c8b0931b3" Conference_bridge_address = "10.244.200.242" Conference_bridge_conference_name = "0010351100040x5c57e406b51ad5c4" Conference_bridge_UUID = "57212b6d-5ba2-4b48-a7d3-68e4693be648" elements UTCTime = "2016-08-08 02:59:33, 425"
  2016-08 - 08T 12: 59:33.218 + 10:00 conferencefactory.controller: Level = "INFO" Event = 'a conference has been marked for deletion." Conference_name = "0010351100040x5c57e406b51ad5c4" Conference_unique_identifier = "c9c8420c47ef8d873abbf138adbf3e5c8b0931b3" Conference_bridge_address = "10.244.200.242" Conference_bridge_conference_name = "0010351100040x5c57e406b51ad5c4" Conference_bridge_UUID = "57212b6d-5ba2-4b48-a7d3-68e4693be648" elements UTCTime = "2016-08-08 02:59:33, 218"

  Any ideas would really be appricated. I've enabled diagnostics logging, but don't see anything in there that I can identify as being the issue

  Hi, I had this problem today as well. We have solved the problem by changing a timer to the default value.

  Could you please check the following Service parameter:

  SIP message size entrants Max: 11000

  Please see the following link for more information.

  http://www.Cisco.com/c/en/us/support/docs/conferencing/Telepresence-Serv...

  See you soon!

• 7936 conference phone lock / freezing

  This issue was published on January 20, 2016 and was not resolved, so I still have the problem.

  I have several IP Cisco 7936 conference phones that locking up and the only way to get them operational again is to supply their market, however don't not all phones 7936 I behave like that. I also tried to reset the phones that are listed as not registered to in CUCM but it does not, that remove and reapply power to solve the problem.

  My version of CUCM is 7.1.5.34900 - 7 and the firmware loaded on every 7936 phone cmterm_7936.3 - 3-20-0.

  Please, please can someone help?

  The version of cucm and 7936 are the two end of support. The best solution is to try to update the firmware of these 7936 to the last. Are they used to run correctly on an earlier version of the firmware, then you can consider downgrading the firmware as well.

  Manish

• Disconnection of the Station 8831 - Conference wireless microphones

  Hi, someone has met unpairing wireless mics themselves? I can succesfully pair but from time to time (almost once a week) they randomy désapparier themselves, the only thing I can imagine to get here is that they store in an office where they get away from the central station and they put in the conference room just before the meetings. Would this have something to do? Someone knows something similar? Any help would be much appreciated, thank you.

  Hi Alfredo.

  If the microphones work well for 7 days continuous basic performance parameters are met. In order to rule out any problems with the microphones being held away outside the range of 8831, try to keep one set of microphones near the 8831 for 10 days and see if the issue is known. At least, this will isolate the whole here.

  HTH

  Manish

• Appeal iPhone issues 7 more

  I recently bought the new iPhone 7 more.  Not only am I having problems with the LTE service, bounce back between 3 G and no service I am now having problems with call connectivity.  When you try to make an outgoing call, I get an automatic response from my carrier (Verizon) "it's Verizon, we are unable to complete your call at this time, please turn off your phone and back and try again."

  It is a known issue with the iPhone 7 and Verizon. Supposed to be Apple and Verizon are seeking him. It has been a problem since the phone was released. Do a Google search or search here on the forums for a temporary solution but not a cure.  But basically to stop the LTE oice and data into data only in the settings.

• iPhone 6 more hang freeze issues

  My iPhone 6 more guard suspended (gel) for the past 6 months, I have to reset the whole phone sometimes up to 2 times just to get it to work again. Been a loyal (including my entire family) custome since gen 1 iPhone, iPad, mac book. Am really disappointed with the quality now. Did not bring to the service center since the first day of the problem because I thought that was just a few bugs & was sure that apple will fix it, but after many update of iOS so far, the pesisit still problem.

  iPhone is more quality I've known, hope apple can fix this problem before finally losing the most loyal customers

  Hello BennyFoo,

  Thank you for bringing your iPhone freeze questions here for Apple Support communities. I understand how it is important to have a reliable phone. I'm happy to check this with you.

  The first thing we want to make sure that all of your data on your device is safe. You can perform a backup in iCloud or iTunes using this article: backing up your iPhone, iPad, and iPod touch.

  Once your data is safe, try to turn off your device, then again on the March. Sometimes, that's all that is needed for connections reset and everything working properly again. This article help from Apple will help you to do: restart your iPad, iPhone or iPod touch. If you are still having issues, try force reset then. It is designed to be used when the iPhone does not respond, and it looks to be the exact symptoms that you are experiencing right now.

  If you still experience the same problems after reboot, please try to restore your device from a backup by using this article help: restore your iPhone, iPad or iPod touch from a backup. If you don't have a current backup, please try this help article: If you can not update or restore your iPhone, iPad, or iPod touch. Please pay close attention when you get to step 4 who said "when you see the option restore or put to update, choose update. iTunes will try to reinstall iOS without erasing your data. "to get your iOS reinstalled. Test if the issue is still ongoing.

  Thanks again and have a great rest of your day.

• Great course more conferences play clear at the end?

  My lectures great course more frequently 'freeze' in about 2-3 minutes.  All I have this problem and solved?  How?

  Hi johngardner1,

  Please visit Apple support communities.

  It looks like your great course more conferences freeze on your Apple TV. It seems you found a great Support article on assistance of content providers.

  Here's another link with the steps that can help with this Apple TV app, troubleshooting if you have not already tried these steps:
  

  Get help with third-party applications on your Apple TV

  All the best.

• Pages on issues of formatting to iCloud

  Hey everybody,

  I created a document Pages using the Pages application on my macbook pro I downloaded then to iCloud Pages so that I can access it from any computer. The issue I'm having is that I formatted some of the text to have a black background and the text to yellow color. For the life of me I can't understand how to change the background color of text on the Pages of iCloud. I beginning to think that changing the background color of text just is not possible on the platform of iCloud, but wanted to put this out there just to make sure.

  I appreciate any help or clarification on this issue.

  Thank you!

  Background (highlight) text color controls are absent in the Pages for iCloud, because it is a subset of Pages for Mac.

  This has been discussed in a previous post here, not so long ago.

• External hard drive mounting issues on MacOS Sierra

  After upgrading to OS Sierra, I found that my USB3 drives, directly connected to my iMac end of 2012, turn off at startup. USB 2 disks are unaffected and connect properly. The only way to access my USB3 disks is to disconnect and reconnect every time I start the computer, then they are ok. I tried to reset the NVRAM, but it did not work. I found Os El Capitan until this issue is resolved.

  Do not mount or actually turns out always the system start? It was not clear in your subject line and content later, what was going on.

  Are they NTFS formatted drives? See the solutions frequently asked and answered forum if they are.