Spaceport.sys BSOD KERNEL_DATA_INPAGE_ERROR

Similar Questions

• kernel data inpage error spaceport sys

  Hey

  I just got a new pc, and whenever I stopped and it starts up again, I get an error: kernel data inpage error spaceport sys

  and the computer just start windows normally.

  What to do / how to fix it?

  Good morning Martine.

  For more information, see the error below:

  -+------------------------------------------------------------------------------------------------------------------

  7 has error checking, {fffff6fc40009b08, ffffffffc0000185, 1 c 2042860, fffff880013617ec}

  GetPointerFromAddress: unable to read from fffff80151b76170
  WARNING: Unable to verify timestamp for win32k.sys
  ERROR: Module load completed but symbols can be loaded for win32k.sys
  Probably caused by: memory_corruption

  Follow-up: memory_corruption
  ---------

  0: kd >! analyze - v
  *******************************************************************************
  *                                                                             *
  * Bugcheck analysis *.
  *                                                                             *
  *******************************************************************************

  KERNEL_DATA_INPAGE_ERROR (7A)
  The requested page of kernel data could not be read in.  Usually caused by
  a bad block in the disk controller or paging file error. See also
  KERNEL_STACK_INPAGE_ERROR.
  If the error status 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185,
  This means that the disk subsystem has suffered a failure.
  If the status of the error is 0xC000009A, it means the query failed because
  a file system has failed to move forward.
  Arguments:
  Arg1: fffff6fc40009b08, type of lock which took place (1,2,3 or PTE address value)
  Arg2: ffffffffc0000185, error state (state code of e/s normally)
  Arg3: 00000001c 2042860, the current process (virtual address for the lock type 3 or PTE)
  Arg4: fffff880013617ec, virtual address that could not be paged in (or PTE contents if arg1 is a PTE address)

  Debugging information:
  ------------------

  Error_code: (NTSTATUS) 0xc0000185 - peripheral of e/s reported an IO error.

  -+------------------------------------------------------------------------------------------------------------------

  It seems that you have a bad hard drive or RAM module in your new system (ran 6 hollow landfill WinDBG), since it is a new system, I would bring her to the store you bought and let replace it.

  Read this guide on how to test your RAM Modules: http://www.pcadvisor.co.uk/how-to/pc-upgrades/3432631/how-check-for-bad-ram-modules-in-your-pc/

  Read this guide on how to test your hard drive: http://pcsupport.about.com/od/toolsofthetrade/tp/tophddiag.htm

  Personally, I'd suggest to return the computer to the store and allow them to correct the problem, apparently not driver related to me (especially if you updated all..), it seems that you have a malfunction of the equipment.

  You can try and run CHKDISK (http://windows8themes.org/how-to-run-chkdsk-in-windows-8.html), but I suggest you RMA your system and let check the RAM and hard drive.

  If however, you want to ensure that it is not Windows, then reinstall Windows and see if the problems come back, but I bet they will be.

  I know this answer might not be what you want... but...

  Yuri

• Windows 7 professional code error 0x0d1 netio.sys BSOD

  My computer laptop thinkpad from lenovo for the last days shows the netio.sys BSOD error several times per day. I ran memory diagnostics and does not report any error. I used view bluescreen but can't figure out where exactly is the problem. Also, I installed all the updates of important windows as optional (it installed all except 2 - Broadcom Corporation - Bus USB and Ports controllers - ThinkPad Bluetooth 3.0 and ATI Technologies Inc. - Display - ATI Mobility Radeon HD 545v in case this is useful information). However the problem is still ongoing. I can't reset it as I have a working demo on 14/06/13 on this and I don't want to lose all the data so close to the end... Help, please! Thanks in advance

  Hello

  For netio.sys errors updated network driver (NIC) and wireless (WiFi) drivers from the
  Site of the manufacturer of system/motherboard if embedded and the sites of manufacturers of real devices if they are separated
  devices. Check also for the update of the BIOS and the low level chipset drivers

• Windows BSOD KERNEL_DATA_INPAGE_ERROR 8; Ntoskrnl.exe + 7 has 040

  Hello world

  I had reinstall Windows 8 last month cause too many errors with the Windows 8 and I had still BOSD arrives with a new installation of Windows 8.

  The last that I have no will is this one:

  KERNEL_DATA_INPAGE_ERROR

  Ntoskrnl.exe + 7 has 040

  We arrive in surfing on the web and burning with IMGBURN. Many Disconnections occur when you use the dvd burner.

  The other at the moment that I solved is "atikmpag.sys" I read on the net that I need to update the file from a download of catalyst frensh.

  Here all DUMP files and the news of the computer:

  All files: https://skydrive.live.com/redir?resid=10F449F32E80D9B2! 390

  Thank you!

  8ternity

  They were related to the following

  KERNEL_DATA_INPAGE_ERROR (7A)
  The requested page of kernel data could not be read in.  Is usually caused by
  a bad block in the disk controller or paging file error.

  My gut feeling is that it is one of these drivers or your moy.  I would like to update the drivers and replace AVG with the built-in Defender

  000 fcl 26/09/2008 09:11:22
  ksaud.sys 2010-07-14 06:12:54
  ntk_PowerDVD_64.sys 03/08/2010 05:04:12
  PxHlpa64.sys 2011-10-17 10:29:34
  amdsbs.sys 21/02/2012 14:15:43

  AVG can be a cause of BSOD.

  http://www.Avg.com/us-en/utilities

  How to find drivers:
  -Google search for the name of the driver
  -compare Google results with what is installed on your system to determine on what device/program, it belongs to
  -Visit the web site of the manufacturer of the hardware or program to get the latest drivers (do not use Windows Update or Device Manager Update Driver function).
  s ' there is difficult to locate them, post back with questions, and someone will try and help you find the right program

  The most common drivers are listed on this page: driver reference

  http://www.carrona.org/dvrref.php

  http://SysNative.com/drivers/

  -Driver manufacturer links are on this page: http://www.carrona.org

• atikmdag.sys BSOD appears on Satellite C850-19 q after 8.1 Win update

  Help, please.

  I have Satellite C850-19 q (PSCBYE-00L00GY4), Windows 8 x 64, after that I have updated to 8.1 on store, show me BSOD (atikmdag.sys system_thread_exception_not_handled).

  I tried to reinstall windows and install again all drivers and updates, nothing has changed.

  Do you have any suggestions?
  Thanks in advance.

  Sorry for my mistakes in English

  Hello

  Have you updated your operating system instructions offered on http://www.toshiba.eu/innovation/generic/windows8_1-message/?

• iaStor.sys BSOD on my new satellite U series

  Hello.

  All of a sudden without any update, or a new program installation, my laptop start BSOD (BSOD iaStor.sys & iaStorA.sys) and restart...
  * Both on safe mode and normal mode.
  * I try the last known good configuration, but nothing.
  * I also tried to system restore to another point of restoration, a few days before that the problem but nothing.
  * I tried with a lot of viruses/malware/rootkit programs, but nothing. It's clean.
  * I tried to uninstall/install but intel rapid storage driver nothing.
  * I uncheck in msconfig-> services menu but nothing.
  * I have uninstall antivirus.
  * I went to the bios and I load the default settings.
  * I uncheck everything in msconfig--> startup.

  * Finally, I did system restore settings by default, but when I go to the last menu, I had the same BSOD... Help, please. I don't know what else to try! :( :( :( . Any idea? The laptop is new. I have only two months. He is too young to go to toshiba service :(

  http://imagizer.imageshack.us/v2/XQ90/594/xijw.jpg
  http://imagizer.imageshack.us/v2/XQ90/819/3ec1.jpg

  The screenshots of the blue screen shows the details of the file iastor.sys.
  This file iastor.sys belongs to the SATA controller driver.

  Especially this kind of BSOD would appear if you must pass between the compatible mode (IDE) and AHCI in the BIOS.

  It could also be that the HARD internal disk works badly or the HARD disk controller.

  But I think you should start the basic principles which is the replacement of the HARD disk.
  The warranty is valid?
  I recommend you contact a technician because in this case, the warranty would cover the repair costs in case of valid warranty.

• ATHR.sys BSOD on Satellite A100-027

  Well I keep a fall of connectivity on my Equium and sometimes, I get a BSOD (athr.sys, you probably know is wireless drivers).

  How could this be fixed?
  I m still on Vista, btw

  Try this:

  * Update the BIOS.
  * Uninstall everything related to Atheros or wireless in Control Panel-> programs and features
  * Uninstall the driver wireless in Control Panel-> system-> Device Manager.
  * Reinstall the latest driver Atheros Wireless

  Drivers and BIOS:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

• Satellite L850 - atikmpag.sys BSOD

  News of the computer:

  Satellite L850-0EF01JAR
  (bought in the Kingdom of Saudi Arabia)
  pre-installed with Win 7 64 bit home edition Basic, up-to-date online to Ultimate

  Question:

  -After a LCD problem, bought an external monitor and reformatted computer
  -update of the AMD drivers but to atikmpag.sys does not BSOD
  -ran DDU and downloaded/installed the drivers from the website toshiba.eu but after reboot, same problem
  -DDU is represented, reinstalled the driver only (without centre of AMD catalyst) but same problem after reboot
  -use the Toshiba Recovery settings but after he installed the display driver, it gives bsod
  -employee Toshiba recover to wipe the HD, ran the recovery, but had the same problem
  -now, I've used toshiba recover to annihilate HD, reinstall windows, install the toshiba display driver, has not restarted the pc, downloaded the drivers omega 14.12 AMD amd, extracted, copied atikmpag.sy_ and has developed, where atikmpag.sys copied and pasted on system32/drivers with the former being renamed to atikmpag.sys.old. (file size difference is large enough; old atikmpag is 350 KB, the news was 500 + kb)
  -restarted the pc and it started
  -Check the Device Manager, it shows yellow exclamation on amd point and driver details shows atikmpag.sys is not digitally signed
  -start on win pc options, advanced disabled driver signature backup and I got BSOD...
  -check the forums as well as a post said on a kb3004934 of victory was updated, but I have not just on my own...

  so, what is next?

  Hello

  I can't find exact laptop specifications and don t know what version of Win7 you have with your machine, but I can't imagine that you have such problems after the original recovery image installation.
  Original recovery image contains drivers tested for your machine.

  Sorry, but I must ask you once more: you may have noticed this problem even if you have installed the original recovery image that you got with your machine?

• Win32k.sys BSOD Intermittent problem

  I got a problem for several months with my computer all of a sudden stop and will the BSOD. The problem seems to occur when something on the InterNet, such as; From IE8/Google Chrome, access to a new tab, using the link that begins the new tab, change the pages and even beginner Email (Outlook Express). My system, in its current form, has run flawlessly since 2009. The complaint of BS is still the same: PAGE_FAULT_IN_NONPAGED_AREA, then that indicates a problem with win32k.sys. This question IS NOT preceded by a power interruption. I have a genuine XP installation with Service Pack 2 CD (because it is upgraded to SP3).

  I tried to find the fault using MemTest 86 (boot from CD when you run the test) and my RAM memory test. No defects found in 10 run tests.
  I had once an indication that there may be a flaw in Z: drive.  Drive Z: is a physically separated, HD 20 GB which stores much of the things of the InterNet as cookies, graphics, etc., and all files downloaded from the InterNet are stored on this drive (to avoid infecting my system drive). I ran CHECKDISK tool with Scan for and attempt recovery of bad sectors checked options and Auto-Fix file system errors. Connected the CHKDSK boot by following the instructions. No problems found.
  I also use CCleaner v4.09 to remove most of the detritus left by the InterNet (especially on drive Z :) and also check the register of questions.
  I have also four Minidump.DMP zipped files (using 7-Zip [file .7z]), but do not have the installation on this page to send the files damaged by arches. I file before, but not SkyNet or whatever is the sharing of files also mentioned elsewhere.

  System Specs:

  Make & model: Auto built in 2008

  Motherboard: ASRock 4Core1600-D800

  Processor: Intel Celeron CPU 430 @ 1.8 GHz, pin 775

  RAM: 3.0 GB of installed Ram (2 sticks [?])

  Video: ATI Radeon HD 2600 Pro (256 MB RAM DDR2)

  DVD installed: HL-DT-ST DVDRAM GH24NS90 R / W DVD

  System:

  WINDOWS XP HOME v2002 SP3 + w/SP2

  Antivirus: Trend Micro Titanium

  News of the blue screen:

  PAGE_FAULT_IN_NONPAGED_AREA

  STOP: 0X0000008E (0XC0000005, 0XBF905FAE, 0XA8BA29F8, 0X00000000)

  WIN32K. SYS - ADDRESS BF9005AFE BASE AT BF800000, time STAMP: 521ea476

  Has occurred @ 10:10, 04/12/13

  #2

  PAGE_FAULT_IN_NONPAGED_AREA

  STOP: 0 X 00000050 (0XE15F001C, 0X00000001, 0X00000000, 0XBF84B3D0)

  WIN32K. SYS - ADDRESS BF84B3D0 BASE AT BF800000, time STAMP: 52706e3f

  Was held on 15/12/13

  Proteus

  Worked well but had to respond to survey questions to continue.

  It was final but related to memory.  I doubt it's the memory itself, so I'd start by Driver Verifier.

  These accidents were related to the corruption of memory (probably caused by a driver).

  Please run these tests to check your memory and find which driver is causing the problem.

  
  

  If you're overclocking (pushing components beyond their design) return you to default at least until the crash is resolved. If you don't know what it is that you're probably not overclocking.

  1-Memtest. (You can read about running memtest here)

  2-Driver Verifier (for full instructions, see our wiki here)
  
  
  If you encounter problems or get stuck at any point, feel free to ask questions
  
  
  If you are unable to Windows because it crashes too early, try safe mode.
  
  If you can't mode without fail, try to use the system from the installation DVD restore to bring the system back to the previous point of restoration that you created.
  Co-written by JMH3143

• Unable to start XP in safe mode, stuck at mup.sys; BSOD with installation disc

  My computer is a computer laptop Asus eeePC 1000H with no material changes and default OS. I left the machine all night and came to see the machine with the error text:

  "Reboot and select proper boot device."
  "or Insert Boot Media in some boot device and press a key.

  Restart in safe mode gave me the same error, except that I could see that the boot process failed at mup.sys.

  Then I tried to repair my installation by using a Windows XP installation disc so I could use the Recovery Console, but I got a BSOD and error:

  STOP 0X0000007E (0XC0000005, 0XF75DE0BF, 0XF7A2A208, 0XF7A29F08)
  PCI.sys-address F75DE0BF base at F75D7000 Datestamp 3b7d855c

  I have turned off unnecessary equipment in the BIOS and still have the same result. The next step here is to erase completely the machine and retemplate TI - something I'm eager to avoid.

  I've been surfing on support forums all morning and I noticed that there is a spike in people with this problem. Is there a virus going around or was there a windows update last night? I use McAfee if it makes a difference.

  From your description of the problem, it sounds like the hardware failure, no software (virus). First test the drive and RAM. Since you don't have a CD player with eeePCs, you need to use bootable USB based on keys of an external optical drive or troubleshooting tools. Or, if the computer is under warranty, contact Asus support.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot

  If you can not do the test yourself and/or are uncomfortable opening your computer, take the machine to a professional computer repair shop (not your local equivalent of BigComputerStore/GeekSquad).
  MS - MVP - Elephant Boy computers - don't panic!

• HP ProBook 4530 s: igdpmd64.sys BSOD on HP ProBook 4530 s Windows 7 64 bit

  I used my HP ProBook 4530 s with 64-bit Windows 7 and Internet Explorer 8 (IE8) installed for 2011 with no problems.
  Recently I upgraded Windows SP1 and IE10. Everything works well except one thing.
  When I run IE10, open a few tabs and hoover my mouse on the icon IE10 so that it shows the small windows semi-transparent my PC crashes.

  It shows the blue screen with PAGE_FAULT_IN_NONPAGED_AREA message caused by the igdpmd64.sys driver.

  (1) I found in the HP forum post "BSOD on HP Envy14t igdpmd64.sys".
  I followed the recommendation of uninstall KB2670838.
  However after restart of PC the IE10 disappeared and IE8 is back to life.
  I've updated Windows then tries to block the installation of KB2670838, but it was impossible since KB2670838 was not indicated on the list but somehow "installed in the background.
  So I was at the point of "all works fine except one thing.

  (2) I found another post on the forum who recommended to upgrade the driver igdpmd64.sys.
  I went to: http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=5060881&swLangOid=8&swEnvOid=4058
  Choose: Drivers - Graphics (3)
  Downloaded the new Intel Graphics Kernel Mode Driver 8.15.10.2559 2012-02-22
  However during the installation process, I received a message (2A):
  "This computer does not have the minimum requirements for installing the software.

  I called HP support who advised to install the previous version of the driver.
  I did, but got the same message (2A)

  I called HP support once again who advised to install the driver from the Intel page.

  (3) I went to: https://downloadcenter.intel.com/search?keyword=Intel%c2%ae+Q45+Express+Chipset
  Downloaded: Intel® Graphics Media Accelerator Driver, Windows 7 * 64, Windows Vista * 64 (exe)
  version of the driver 15.17.19.64.2869 (8.15.10.2869) for Intel® integrated graphics.

  However during the installation process, I received a message (2A).

  I have no more ideas. Could someone help me please?

  Best regards

  Sylwek

  I know it's weird that I reply to myself.
  HP support advised me to install the ATI video driver and Control Panel

  to:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=5060881&swItemId=ob_101995_1&swEnvOid=4059#tab1

  He helped :-)

  Thank you HP support Poland

• T410 nvlddmkm.sys BSOD on startup

  Hi all

  I had my T410 since the end of last month and had a BSOD on startup several times so far. Whenever I caught, I noticed that the driver nvlddmkm.sys nvidia was the cause. Each time the BSOD, I get the prompt "windows did not start successfully", how by selecting "Start windows normally" translates the fine start System. Since this BSOD is only presented to a cold start, I'm not too hampered by it outside my boot up times by doubling the time it does. I ran the update of the bios/driver Thinkvantage, as well as I'm running with the latest updates for Win7 Pro x 64.

  Everyone knows this? If so, have you found a solution? No matter what Lenovo personal support out there have an entry?

  Thank you

  TSalinas

  
  

• Windows Vista (x 86) NetIO.SYS BSOD me HELP!

  Whenever I use uTorrent to download, I get the BSOD, usually this happens when you listen to music with WMP 11.

  I am running Vista SP2 with all latest UPDATES, installed the latest drivers for my motherboard on site manufactor and latest driver for my video card.

  Here is a dump to analyze MEMORY. DMP (300MB): http://pastebin.com/mjviD3uu

  analyze of mini dump bucket: http://pastebin.com/in5HuLaN

  I formatted my PC and reinstalled Vista Home Premium and happens again, OMG!

  I changed my BIOS settings for optimized def and again! even on Ultimate SP2 happens, OMG!.

  WHAT TO DO! ? It always happens even if I leave my PC alone for a few minutes! OMG!

  Download all 3 sites:
  http://www.speedyshare.com/files/21380459/dumps.rar

  Hello

  1. don't you see 0x000000D1 on BSOD error code? If not, what is the error code?
  2. using a single processor or a computer equipped with multi processors?

  This occurs usually after a driver for a third-party network adapter is installed. NETIO.sys is a driver file.

  We recommend that you uninstall the driver of network adapter in the Device Manager and allow Windows to install a generic driver. To do this, follow these steps.
  1. click on start, type devmgmt.msc, then right-click on devmgmt and click Run as administrator.
  2. from the list of objects, expand network adapters.
  3. right click on the sub elements and click on uninstall.
  4 restart the computer for changes to take effect.
  5. once the computer is restarted, windows will load the generic driver.

  Make sure that your computer is up-to-date.

  I hope this helps.

  Kind regards
  Syed
  Answers from Microsoft supports the engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1) netio.sys BSOD

  Hello

  I am really lost and hope that someone of you could bring some light here.

  I'm dealing with BlueScreens 3 last month. All have the same reason. However, I've never had a blue screen before them.

  In general, it seems like a bug in the driver of the CARD, but in contradiction with this is

  1. that I never faced a blue screen before. The system is stable for 1 year >!

  2. I did not change any hardware or any driver!

  An additional comment, the system executes the of in an ESX environment.

  I really hope that someone can help me to get rid of this annoying situation.

  Here is the output in WinDbg:

  Microsoft (R) Windows debug 6.3.9600.17298 AMD64 Version
  Copyright (c) Microsoft Corporation. All rights reserved.

  Loading dump file [C:\TEMP\BSOD\022515-87812-01.dmp]
  The mini kernel dump file: only registers and the trace of the stack are available

  Symbol of validation of the path summary *.
  Location of response time (ms)
  Deferred SRV * C:\TEMP\Symbols4Debug* http://msdl.microsoft.com/download/symbols
  Symbol search path is: SRV * C:\TEMP\Symbols4Debug* http://msdl.microsoft.com/download/symbols
  Executable search path is:
  Windows 7 Kernel Version 7601 (Service Pack 1) MP (2 processors) free x 64
  Product: LanManNt, suite: TerminalServer SingleUserTS SmallBusinessRestricted SmallBusiness
  By: 7601.18717.amd64fre.win7sp1_gdr.150113 - 1808
  Computer name:
  Kernel base = 0xfffff800'01802000 PsLoadedModuleList = 0xfffff800'01 has 46890
  The debugging session: Wed Feb 25 10:51:47.913 2015 (UTC + 01:00)
  System Uptime: 1 day 2:35:07.836
  Loading the kernel symbols
  .

  Press (cdb, ntsd, kd) ctrl-c or ctrl-BREAK (windbg) to drop the charges of symbol that take too much time.
  Run! SYM noisy before .reload to track symbols loading issues.

  ..............................................................
  ................................................................
  ............
  Loading user symbols
  Loading unloaded module list
  ...........
  *******************************************************************************
  *                                                                             *
  * Bugcheck analysis *.
  *                                                                             *
  *******************************************************************************

  Use! analyze - v to obtain detailed debugging information.

  BugCheck D1, {0, 2, 0, fffff8800189456b}

  Probably caused by: NETIO. SYS (NETIO! NetioDereferenceNetBufferList + 86)

  Follow-up: MachineOwner
  ---------

  0: kd >! analyze - v
  *******************************************************************************
  *                                                                             *
  * Bugcheck analysis *.
  *                                                                             *
  *******************************************************************************

  DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1)
  An attempt was made to access an address pageable (or completely invalid) to a
  application interrupt level (IRQL) that is too high.  It is usually
  caused by drivers using a wrong address.
  If the kernel debugger is available, get a stack backtrace.
  Arguments:
  Arg1: 0000000000000000, referenced memory
  Arg2: 0000000000000002, IRQL
  Arg3: 0000000000000000, value 0 = read operation, 1 = write operation
  Arg4: fffff8800189456b, address memory

  Debugging information:
  ------------------

  READ_ADDRESS: GetPointerFromAddress: unable to read from fffff80001ab0100
  GetUlongFromAddress: cannot read fffff80001ab01c0
  Paged 0000000000000000

  CURRENT_IRQL: 2

  FAULTING_IP:
  Tcpip! : FNODOBFM: 'chain' + 57b 4
  fffff880'0189456 b 488b 01 mov rax, qword ptr [rcx]

  CUSTOMER_CRASH_COUNT: 1

  DEFAULT_BUCKET_ID: WIN7_DRIVER_FAULT_SERVER

  BUGCHECK_STR: 0XD1

  Nom_processus: System

  ANALYSIS_VERSION: 6.3.9600.17298 (debuggers (dbg). 141024-1500) amd64fre

  DPC_STACK_BASE: FFFFF800016A0FB0

  TRAP_FRAME: fffff80001699f00-(.trap 0xfffff80001699f00)
  NOTE: The frame trap does contain not all registers.
  Some registry values can be set to zero or incorrect.
  Rax = fffffa800b55edf0 rbx = 0000000000000000 rcx = 0000000000000000
  RDX = fffffa800b55edf1 rsi = 0000000000000000 rdi = 0000000000000000
  RIP = fffff8800189456b rsp = fffff8000169a090 rbp = 0000000000000000
  R8 = fffffa800b55edf0 r9 = 00000000000000d 0 = fffff800019f4b80 r10
  R11 = fffffa8009139a70 r12 = 0000000000000000 r13 = 0000000000000000
  R14 = 0000000000000000 r15 = 0000000000000000
  iopl = 0 nv in pe of na EI ng nz nc
  Tcpip! : FNODOBFM: 'string' + 0x57b4:
  fffff880'0189456 b 488b 01 mov rax, qword ptr [rcx] ds:00000000'00000000 =?
  Reset the default scope

  LAST_CONTROL_TRANSFER: from fffff80001876469 to fffff80001876ec0

  STACK_TEXT:
  fffff800'01699db8 fffff800'01876469: 00000000' 0000000 a 00000000'00000000 00000000'00000002 00000000'00000000: nt! KeBugCheckEx
  "fffff800 '01699dc0 fffff800' 018750e0: fffffa80' 0889b 001 00000000' 0000002a fffffa80 ' 00000008 fffffa80 ' 092efc10: nt! KiBugCheckDispatch + 0 x 69
  "fffff800 '01699f00 fffff880' 0189456b: fffffa80 ' 092efc10 fffffa80 ' 087 d 2428 fffff880 ' 206c644d fffffa80 ' 0cf0d470: nt! KiPageFault + 0 x 260
  fffff800 '0169-090 fffff880' 00e61316: fffffa80 '092efc10 00000000'08542768 00000000'00000000 fffff800' 019ac1ee: tcpip! : FNODOBFM: 'string' + 0x57b4
  fffff800 '0169a0e0 fffff880' 00e60a72: 00000000'00000000 00000000'00000000 00000000'00000002 00000000'00001000: NETIO! NetioDereferenceNetBufferList + 0 x 86
  fffff800'0169 has 110 fffff880'018494 6 c: 00000000'00000000 00000000'00000000 fffff800 '0169-100 fffffa80' 0c521e20: NETIO! NetioDereferenceNetBufferListChain + 0 x 332
  fffff800'0169a1e0 fffff880'01820694: fffffa80 ' 0c521e20 fffffa80 '0c9c4010 fffffa80' 088aa010 fffffa80 ' 0888b 910: tcpip! IppCompleteAndFreePacketList + 0xc6
  "fffff800 '0169-210 fffff880' 018289f8: 00000000 ' 00000000 '088aa010 fffffa80' fffffa80 0888b 910 fffff880 ' 0196d9a0: tcpip! IppCleanupMfe + 0 x 44
  "fffff800 '0169-240 fffff880' 0188a43c: 00000000 ' 00000001 fffff880 ' 01971ee0 fffff800 '0169a2e8 fffffa80' 088aa010: tcpip! IppDereferenceMfe + 0x18
  fffff800 '0169-270 fffff880' 01889b5a: fffff800'0169a4d8 00000000 00000000' fffffa80 '088aa028 fffff800' 0169a4d8: tcpip! IppMfeSetTimeOut + 0x10c
  "fffff800 '0169-390 fffff880' 0188a2ca: fffffa80 ' 0 c 504700 fffff800 ' 0169a4d8 00000000'00000000 00000000'00000000: tcpip! IppCompartmentSetTimeout + 0x9a
  fffff800 '0169-400 fffff800' 01882cfc: fffffa80'08cf82f0 fffffa80'08 d 18000 00000000' abcf518f 00000000' 01d050e0: tcpip! IppTimeout + 0x5a
  fffff800 '0169-430 fffff800' 01882b 96: fffffa80 '0ba87168 fffffa80' 0ba87168 00000000'00000000 00000000'00000000: nt! KiProcessTimerDpcTable + 0x6c
  fffff800 '0169a4a0 fffff800' 01882a7e: 000000de'd650df86 fffff800 '0169ab18 00000000' 005d9d26 fffff800' 019f6748: nt! KiProcessExpiredTimerList + 0xc6
  fffff800'0169aaf0 fffff800'01882867: 0000013f '1031ffd6 0000013f' 005d9d26 0000013f '1031ffa9 00000000' 00000026: nt! KiTimerExpiration + 0x1be
  fffff800 '0169ab90 fffff800' 0186ebca: fffff800 '019f3e80 fffff800' 01a01cc0 00000000 00000000' fffff880'012 c 7500: nt! KiRetireDpcList + 0 x 277
  fffff800 '0169ac40 00000000' 00000000: 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000000: nt! KiIdleLoop + 0x5a

  STACK_COMMAND: kb

  FOLLOWUP_IP:
  NETIO! NetioDereferenceNetBufferList + 86
  fffff880'00e61316 4885ff test rdi, rdi

  SYMBOL_STACK_INDEX: 4

  SYMBOL_NAME: NETIO! NetioDereferenceNetBufferList + 86

  FOLLOWUP_NAME: MachineOwner

  MODULE_NAME: NETIO

  NOM_IMAGE: NETIO. SYS

  DEBUG_FLR_IMAGE_TIMESTAMP: 5294760d

  IMAGE_VERSION: 6.1.7601.18327

  FAILURE_BUCKET_ID: X64_0xD1_NETIO! NetioDereferenceNetBufferList + 86

  BUCKET_ID: X64_0xD1_NETIO! NetioDereferenceNetBufferList + 86

  ANALYSIS_SOURCE: KM

  FAILURE_ID_HASH_STRING: km:x64_0xd1_netio! netiodereferencenetbufferlist + 86

  FAILURE_ID_HASH: {b03a5328-38ca-1e4a-8e26-dcd45efb9256}

  Follow-up: MachineOwner
  ---------

  These accidents were related to the corruption of memory (probably caused by a driver).

  Run these two tests to check your memory and find which driver is causing the problem.  Launch auditor.  You need not run memtest again unless you want to.
  

  If you are overclocking anything reset by default before running these tests.
  In other words STOP!

  If you don't know what it means that you're probably not

  
  

  
  

  
  1-Driver Verifier (for full instructions, see our wiki here)

  2-Memtest. (You can learn more about running memtest here)

  I would like to also update your 2008 e1g6032e. sys Intel (r) PRO/1000 adapter NDIS 6 driver.
  

• NETIO.sys BSOD

  I've been getting regular BSOD on My Windows (32 bit) operating system 7 for quite a few days... I had downloaded the app to display blue screen and it says that it is caused by some ' NETIO. SYS'... However, I can easily start my windows and run without any difficultiy in safe mode... PLEASE HELP ME TO SOLVE THE QUESTION ABOVE...!

  Send a copy of your dump file in a shared file on your disc of sky with a link here.

  The dump file will be created in c:\windows\minidump. You may need to change your settings in Windows to be able to view the file. To show hidden files type Folder Options in the search box above the Start button and select view advanced settings and check that the box "display files and folders" and 'Hide protected operating system files' are not checked. You may need to scroll down to see the second element. You should also make sure that the box before "Hide extensions of known file types" is not checked.

  What is your computer brand and model? If not a branded computer, what is your motherboard brand and model?

  Please download and run the display driver and download a copy of the report he produced on your sky player. To obtain a report all drivers Select Edition, select all followed by file, save selected items.
  http://www.NirSoft.NET/utils/DriverView.html

  Please provide a copy of your system information file. Type system information in the search box above the Start button and press the ENTER key (alternative is select Start, all programs, accessories, System Tools, system information). Select file, Export and give the file a name noting where it is located. The system creates a new information file system each time system information is available. You must allow a minute or two before the file is completely filled before exporting a copy. Please download your disk from sky to share with everyone and post a link here. Please say if the report was obtained in safe mode. The request for a copy of this file is additional to answer the question about the brand and the model.

  Help with Sky Drive see section 9.3:
  http://www.gerryscomputertips.co.UK/MicrosoftCommunity1.htm