Speech sounds

Similar Questions

• speech sounds hollow

  I'm a complete noob when it comes to audio and hearing.

  But maybe someone can push me in the right direction.

  I have this clip from a man speaking in a classroom.

  It was recorded with a Canon XF100 and no external microphone. I wish that I had, but I do not have a microphone along when I am traveling.

  In any case his voice sounds a little hollow. It was about 5 metres the internal mic.

  Y at - it a way to warm up a bit of his voice.

  I don't expect miracles.

  Thanks in advance.

  Ann

  BTW I hearing CS6.

  The reason why the sound is a bit 'hollow' is not your speaker - is the fact that you have saved all the ambience of the room, and it will be at least as strong as him (because it is 5 meters) and irretrievably mixed with him. We often get questions like this--and usually there is very little, or nothing at all, which can be done with it - this is like trying to unbake a cake.

  That said, if it is not too bad, there is a piece of software called "Reveal" who could make a slight difference - although when I tried the trial, there was no practical difference to the material I used on this subject. It of expensive but - more than the cost of a remote microphone for recording speakers with...

• Simultaneous playback and record real-time show levels of vibrations and his Deputy

  First of all I would like to stress that I am very new to Labview (using Labview 2011) and Assistant Sound and Vibration (Labview Signal Express 2011).  I'm starting a project to measure the speech (sound pressure using microphone) and the body of vibration (using the accelerometer) related to the acquisition of data NI 9234.   I looked in the tutorial and the examples provided with Sound and Vibration Assistant (SVA).   These examples allowed me to make a first recording that is connected.  I could view the playback display after I transfer the log to the data view.   Frankly I'm more sure of my measurement data if I could observe the timewave with speech variation.  I wonder if this is possible.  If it's possible, thanks in advance for pointing the direction.

  Thank you.

  Abu Dzarr

  You can look at the data, because it accumulates in one of two ways:

  1. Create a viewer and drag out of the acquisition apparatus in the Viewer.  It will give you a live view of the data.
  
  
  2. Create a viewer and drag the newspaper in the Viewer.  By default, this should show you that the current buffer being written to the file.  You can change that to click with the right button on the graph to view in the viewer and selecting show the whole graph, a static part of the graph, etc.

• Update XP or office 7, made my dumb computer

  installed XP twice, lost his card after an update on XP or Office 7.  thinking it was my installation, I installed again.  Same thing happened that after the upgrade has been installed.  No sound system, not even from CD play.  My Manager diving equipment tells me everything is going well and all the drivers are loaded.  All sound systems are on.

  Have you checked the volume control, maybe it's been cut off or something?

  1. open the control panel in the start menu.
  2. click on the Speech sounds and Audio Devices icon. (Or, depending on how your control panel is set up, click sounds and Audio devices.)
  3. click on "Adjust the system volume."
  TaurArian [MVP] 2005-2010 - Update Services

• I have no volume control in my tadkbar

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  To place the icon beside the clock back volume control, follow these steps:
  1. open the control panel in the start menu.
  2. click on the Speech sounds and Audio Devices icon. (Or, depending on how your control panel is set up, click sounds and Audio devices.)
  3. click on "Adjust the system volume."
  4. click in the box "set the volume in the taskbar icon.
  5. click the button OK and the small speaker icon appears next to the clock, where it should be.

  http://support.Microsoft.com/default.aspx?scid=KB; EN-US; Q319095
  Volume icon appears in the Notification area, and you receive an Error Message When you try to add TaurArian [MVP] 2005-2010 - Update Services

• What's Windows compatible with Jaws 14 8

  I hope someone familiar with JAWS 14 can help (he is a system of speech for the blind).  We have upgraded to Windows 8 Windows XP.   We have also improved to JAWS 14 because we were told it was compatible. Now, someone at Microsoft tells us that the ONLY Windows 8 that came out is Windows 8 Professional and that is not compatible with Jaws 14.  The computer is functional but is not well and I'm stuck. Can someone tell me

  (1) is it true that the only windows 8 that came out is a professional. (I bought online and that I do not remember whether teacher.)

  (2) anyone knows if it is incompatible with the jaws 14?

  Thank you, pat

  I hope someone familiar with JAWS 14 can help (he is a system of speech for the blind).  We have upgraded to Windows 8 Windows XP.   We have also improved to JAWS 14 because we were told it was compatible. Now, someone at Microsoft tells us that the ONLY Windows 8 that came out is Windows 8 Professional and that is not compatible with Jaws 14.  The computer is functional but is not well and I'm stuck. Can someone tell me

  (1) is it true that the only windows 8 that came out is a professional. (I bought online and that I do not remember whether teacher.)

  (2) anyone knows if it is incompatible with the jaws 14?

  Thank you, pat

  Looks like you need 8.1.

  JAWS system requirements

  To use JAWS for Windows, you need a personal computer running Microsoft® Windows® with the following text:
  JAWS home use edition and professional JAWS
  Windows® 8.1, Windows 7, Windows Vista, Windows Server® 2012 and Windows Server 2008

  Processor speed
  Processor 1.5 GHz minimum

  (Vivid RAM) memory
  4 GB recommended (64-bit)
  2 GB recommended (32-bit)

  Required disk space
  20 MB of 690 MB required by the voice for installation of RealSpeak Solo Direct, Vocalizer Direct or expressive Vocalizer voices (file size varies depending on the installed voice)

  Video
  A graphics card capable of screen resolution of at least 800 x 600 with 16-bit colors (screen resolution of 1024 x 768 with 32-bit color recommended)

  Sound
  Compatible Windows (for speech) sound card

• Sounds (music and sounds efects) but no speech in sound of DVD playback. Vista

  Real Player doesn't work at all with DVD

  Windows Media Player does not load even

  Windows Media Center plays a DVD with sound effects and music, but no speeches.

  I have tried different DVD including the new ones, all with the same result.

  Hi, you can read the article and check. Solve problems in Windows Media Player http://windows.microsoft.com/en-us/windows-vista/Troubleshoot-problems-in-Windows-Media-Player

• Speech recognition is not all sounds during installation of the wizard.

  Sound recorder works fine and I can record, save and play wav files.  CLS recognition requires all upward before use and the recording meter bar moves I read the sentence of the sample.  After that, I get the error that SR couldn't hear anything.  Help please.

  Hi BTKpickle,

  Welcome to Microsoft Answers Forum.

  There are several possible causes of the problem:

  ·         The microphone isn't close to capture your voice. Make sure that the microphone is positioned close enough and you speak directly into it.

  ·         The microphone is cut in. Some microphones have an external control for muting. Make sure that the mute control is disabled.

  ·         The microphone input level is too low. Make sure that the microphone input level is set correctly.

  Entry level to adjust the microphone

  1. Open Audio devices and sound themes by clicking Start , clicking onto Control Panel, hardware and sound, and then clicking its.

  2. click on the recording tab.

  3. double-click on the microphone you are using speech recognition.

  4. click on the tab levels and then use the slider to adjust the entry level for your microphone.

  ·         The microphone connections are not properly attached. Make sure that microphone cables are intact and unbroken. The connections to the computer can be loose, so unplug the wires and reconnect them by ensuring that they fit.

  ·         A different microphone is selected to be used with speech recognition. If you have more than one microphone installed on your computer, that bad could be selected to be used with speech recognition. Make sure that you use the microphone selected for speech recognition.

  Change which microphone is used with speech recognition

  1. Open Audio devices and sound themes by clicking Start , clicking onto Control Panel, hardware and sound, and then clicking its.

  2. click on the recording tab.

  3. Select the microphone that you want to use with speech recognition, and then click set as default.

  Check the documentation that came with the microphone for additional troubleshooting information.

  See if you are able to complete the installation wizard.

  For solutions to common problems with Windows speech recognition, see

  Troubleshoot speech recognition

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-speech-recognition-problems

  I hope this helps.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think

• Built in microphone will not pick up sound for Windows speech recognition

  My Dell Inspiron 1545 with a built-in mic, but for some reason any it don't will pick up any sound at all for the Windows speech recognition (Windows Vista).

  Hi Matthew,
   
  Thank you for writing to Microsoft Windows Vista Answers.

  Have you checked to see if the correct settings have been selected for the microphone in the computer?

  Try to access the control panel > Sound > Audio. Check the recording tab if the Microphone is on and working. Click on set up and once you see the working driver (i.e., reacts to your voice), right click on it and the default value.

  Later try to put in place the program of speech recognition in all programs > Accessories > accessibility > Windows speech recognition and try settings different microphone to the edge we respond to your voice.

  You can also try to update the audio drivers. Access the link below and try to download the drivers.
  http://support.Dell.com/support/downloads/DriversList.aspx?OS=WLH&OSL=en&catid=-1&impid=-1&SERVICETAG=&SystemID=INSPIRON1545&hidos=WLH&hidlang=en&TabIndex=

  Also access the link below to troubleshoot the integrated Webcam and digital Microphone array in PC Dell laptop:
  http://support.dell.com/support/topics/global.aspx/support/dsn/document?c=us&l=en&s=gen&docid=397D0C4AF7AA90D8E040A68F5B283A3E&journalid=6DD6C133CFD8091CE040AE0AB5E16CFC&Query=d2ViY2Ft&SystemID=INS_PNT_PM_1520&ServiceTag=&contenttype=-1&os=-1&component=-1&lang=-1&doclang=en&toggle=true#5
   
  Hope one of these AIDS.

  Kind regards
   
  Srinivas
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Microphone picks up foreign sounds other than my usign speech recognition speech.

  Only to learn how to use speech recognition on my Windows 7 laptop.

  Training of speech for Setup microphone went very well...

  .. up to - the microphone picks up foreign sounds other than my speech.

  It displays the message title that was it?

  I then wait for the message to disappear before I continue to talk.

  There are some answers that I can talk to that speech recognition is programmed to accept for that matter?

  Thank you

  Hi John,.

  I understand the inconvenience caused to you.

  Rest assured that I will do my best to help you solve the problem.

  I would like the links and check if that helps to properly use speech recognition.

  Dictate text using speech recognition

  Common commands in speech recognition

  Set up speech recognition

  What can I do with speech recognition?

  Hope this information helps. If you have any other questions about Windows, please let us know.

  Thank you.

• No sound. Volumn checked and also control panel under spund speech and audio, and all devices are OK.

  Under windows XP.

  I have updated drivers and still does not.

  Is there a material that could be bad?

  Hello Ann,.

  Please contact Microsoft Community!

  I understand from the description of the issue that you are having problems with sound playback. I'll be happy to help you with this problem.

  Method 1: I also suggest you to follow the steps from the link and check if the problem persists.

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/no-sound-help#no-sound=Windows-XP&V1H=win8tab1&V2H=win7tab3&V3H=winvistatab1&v4h=winxptab1

  Method 2: Check for any errors in Device Manager driver, then uninstall and reinstall the drivers and check if it helps. The links mentioned below which can help you to fix the problem with the audio device that is installed on your computer.

  Uninstall or reinstall a device

  http://TechNet.Microsoft.com/en-us/library/cc725782.aspx

  I hope this helps. Try the above steps and get back to us for assistance. We will be happy to help you.

• My coming sound sounds as it rotates too fast, also I continue to receive windows popup about speech recognition, what does this mean and can I fix it.

  My sound is distorted when coming, such as Skype, its OK at the other end.  It looks like not running too fast (a bit like the chipmonks.  Also, I don't hear anything when I try to play a CD sample in the music file that came with the computer.  Help

  Hi carolejenkins,

  1. did you of recent changes on the computer?

  2 when was the last time it was working fine?

  3. what happens when you try to read examples of music files on the computer?

  4. are you able to play the other music files on the computer?

  5. what player you use to play music files?

  6. What is the finished message, you receive the recognition of the word on the computer?

  7. do the sound distort occur only with the Skype program?

  Method 1

  If it helps, try the step below and check out them.

  (a) open Sound by clicking on the Start button and then clicking on Control Panel, click sound.

  (b) on the playback tab, click speakers, and then click Properties.

  (c) click the enhancements tab, and then select the checkbox disable all improvements .

  Method 2

  If the previous step fails, then I suggest that you manually download and install the drivers for card its updated on the computer by visiting the manufacturer of the computer or sound card manufacturer's Web site and check if it helps.

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

• No speech DVD when played only background sound and music can be heard with slight deaf speech

  during playback of a dvd on my laptop I can hear the sounds of music and accessories background but only weak dialogue of the deaf. I went into sounds and I tried to change some settings but without success. Can anyone help please.

  Hi skinbyfinn,
   
  1. this happens with other DVDs?
  2. what player you use to play the DVD?
   
  We recommend that you cross check if the same problem persists in playing other video DVDs. Check also play the DVD using a different DVD player.
  
  Please, try the steps following and post back with the results, so that we can help you better.
   
  See play a CD or DVD
  See read an audio or video file: frequently asked questions
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Text-to-speech works through headphones

  I have an iPhone running iOS 9.3.2 and text-to-speech 6 only works if a headphone is plugged. I can hear it well just using headphones, but it does not come out of the speaker, so those who are disconnected. Any ideas? I rebooted, reset and finally restored.

  Check if your speaker works. If you hear no sound or distorted sound of your iPhone, iPad or iPod touch speaker - Apple Support

  -AJ

• Tecra A8 PTA83E - sound in the speakers but work helmet

  Hello

  I recently reinstalled my laptop with a new copy of Windows xp pro. After installing all the drivers where installed correctly, but I have no sound.

  When I put my helmet I can perceive a very low noise.

  Tried almost everything posted on the forums but no luck.

  Someone at - it solution

  Kind regards

  > When I put my helmet I can perceive a very low noise.
  This means that the pilot is ok and possibly that the volume should be increased

  Reach:
  (1) control Panel-> sounds, speech, and Audio Devices section
  (2) select sounds and Audio devices
  (3) sound now and the Group of devices Audio will appear.
  (4) in reading his article click Volume
  (5) in the control of the Volume Group on all controls volume max (foot)

  If this does not help, check out this FAQ from Toshiba:
  http://APS2.toshiba-tro.de/KB0/TSB7C021B0001R01.htm