SSL VPN failover
Hello
I have a SSL VPN 500 license running device. I also have a beam of 5520 firewall only. Can I use the firewall as a failover cluster (active / active OR active / standby) to the current 5520 with 500 licenses SSL?
If this is not the case, what is necessary to have a failover for 5520 with 500 appliance SSL?
Thank you
Wine
If you run version 8.2 and earlier, then you must have the 500 user license of SSL enabled on the new ASA5520 to perform failover.
The two needs of ASA to have exactly the same material, the module, the license to run the failover if they perform version 8.2 and earlier versions.
However, if you are using version 8.3 and later, there is no need to have the 500 user license of SSL enabled on the new ASA5520. You can configure failover immediately.
Hope that answers your question.
Tags: Cisco Security
Similar Questions
-
ASA 5500 SSL VPN Failover license
Hello
I have a partner who request assistance with SSL VPN licenses on the ASA 5500 firewall sharing:
His question is:
Both SSL, provided with the firewall of the SAA, licenses can be shared across a couple active / standby? I would therefore have a total of (4) licenses of SSL VPN to use?
This would also be true for two security contexts that are included with the firewall?
For example, I buy two base ASA 5520 firewall, running active / standby, that each machine is supplied with SSL VPN licenses (2) and (2) licensing of security contexts? In version 8.3, the licenses are cumulative by failover pairs, so I should a total SSL VPN (4) and (4) security contexts?
Here is my response to his request:
Based on this link (http://www.cisco.com/en/US/partner/docs/security/asa/asa83/license_standalone/license_management/license.html#wp1449664)
It was mentioned that:
"You can have one active license type, either the AnyConnect Essentials license or the AnyConnect Premium license. By default, the Adaptive security apparatus includes an AnyConnect Premium license for 2 sessions. If you install the AnyConnect Essentials license, it is used by default. See not anyconnect-essentials control or in ASDM Configuration > remote access VPN > network (Client) access > advanced > component AnyConnect Essentials to activate the Premium license instead. »
It will be able to share the included license on the ASA 5500 4. It will be able to share these licenses, but I'm not sure the security context. My answer would be, it can use only 2 context Security licenses since only the VPN licenses are shared on the version 8.3 and other licenses not characteristic. My understanding is correct? or there are other explanations on my customer survey?
Thanks in advance!
Ice Flancia
Cisco partner Helpline Tier 2 team
Only from ASA 8.3 version and following, the license can be combined on a failover pair active / standby.
2 SSL included license on SAA in failover pair is combined as 4 license SSL.
2 license of background on ASA in failover pair is combined as license frame 4.
Here's the URL on ASA combined license failover:
Hope that helps.
-
Should what license I for 25 SSL VPN peers
Hi all
I want to implement cluster active / standby with a pair of ASAs 5550 and I have a licensing question. Here's the "sh - key retail activation" leave two output devices...
ASA1:
SH - activation in detail key:
Serial number: XXXXX
No temporary key assets.
Activation key running: XXXXX XXXXX XXXXX XXXXX XXXXX
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 250
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
Total of the VPN peers: 5000
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabled
This platform includes an ASA 5550 VPN Premium license.
Flash activation key is the SAME as the key running.
ASA2:
SH - activation in detail key:
Serial number: XXXXX
No temporary key assets.
Activation key running: XXXXX XXXXX XXXXX XXXXX XXXXX
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 250
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
VPN SSL counterparts: 25
Total of the VPN peers: 5000
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabled
This platform includes an ASA 5550 VPN Premium license.
Flash activation key is the SAME as the key running.
--------------------------------------------------------------
It seems so obvious that I have to upgrade the first ASA to support 25 SSL VPN peers in order to create the cluster HA, right?
Now, I want to know do I need the license "ASA5505-SSL25-K9" or something else.
Thank you very much in advance for any help!
Ah OK I see - right then: upgading pole will allow the license to share.
Re the version target, I would recommend going directly to 8.4 (4.1). I have it deployed on several sites without problem.
-
Hello
I want to configure SSL VPN on my Cisco ASA 5510 for more information, then 30 users will have to access simultaneously, but I don't know if my license that allow.
Below is the features of my ASA license:
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 50
Internal hosts: unlimited
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 0
GTP/GPRS: disabled
SSL VPN peers: 2
The VPN peers total: 250
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect for Linksys phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabledThis platform includes a basic license.
Concerning
Walid
You ASA have a license for this. You need to order AnyConnect MORE if you want to use the AnyConnect Client or you have licenses AnyConnect APEX order if you want to use the VPN without client.
The two are not allowed on the simultaneous connections. You must count users who use them. MOR info is in the Guide of command AnyConnect.
-
ASA 5520 - SSL VPN (Anyconnect) licenses
Hello
Can someone clarify for me the SSL VPN/AnyConnect for the ASA 5520 license? Specifically, the differences between the AnyConnect Essentials and AnyConnect Premium. Our current license looks like this:
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 150
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
Total of the VPN peers: 750
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabledThis platform includes an ASA 5520 VPN Plus license.
I guess that means that we have just the 2 'free trial' SSL VPN licenses and nothing else.
I would like to add 25 or maybe 50 SSL VPN licenses and be able to use a combination of full free client, thin client and groups client AnyConnect. The 'ASA5500-SSL-25' (or 50) would be the correct license I need to buy?
Thank you
Rob
Hello
The essentials license is per device and does not allow full-tunnel.
If you need other features like Secure Desktop, without client SSL and other optional features such as shared licenses, you must go to the Premium license.
Federico.
-
ASA 5520 Active standby and ssl vpn loadbalancing
I have a pair of Asa 5520 failover active rescue running. Can I use these two machines in a cluster of ssl vpn load balancing?
N ° when a couple active / standby is part of a cluster of VPN, the rescue unit is still pending - she will not be actively terminate user sessions. Only the active cluster members (and non-failover) will do.
-
Router WAN double with SSL VPN inaccessible for customers
I have a configured in a Dual WAN setup Cisco 888. There is an ADSL link connected to the VLAN 100 and a SDSL link associated with the Dialer0. The customer wishes to use the ADSL link to the normal navigation and external SSL VPN users to complete on the SDSL connection. I tried to configure the link failover for the ADSL SDSL.
What works:
-Access to the Internet for clients the
What does not work:
-The ADSL SDSL connection failover.
-Access SSL VPN for customers. Surf to the external IP address will cause only a page by default HTTP. Specification webvpn.html results in a 404 not found error.
Here is my configuration:
version 15.0
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
host name x
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 x
!
AAA new-model
!
!
AAA authentication login local sslvpn
!
!
!
!
!
AAA - the id of the joint session
iomem 10 memory size
!
Crypto pki trustpoint TP-self-signed-3964912732
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 3964912732
revocation checking no
rsakeypair TP-self-signed-3964912732
!
!
TP-self-signed-3964912732 crypto pki certificate chain
self-signed certificate 03
x
quit smoking
IP source-route
!
!
IP dhcp excluded-address 192.168.10.254
DHCP excluded-address IP 192.168.10.10 192.168.10.20
!
DHCP IP CCP-pool
import all
network 192.168.10.0 255.255.255.0
default router 192.168.10.254
DNS-server 213.75.63.36 213.75.63.70
Rental 2 0
!
!
IP cef
no ip domain search
property intellectual name x
No ipv6 cef
!
!
udi pid CISCO888-K9 sn x license
!
!
username secret privilege 15 ciscoadmin 5 x
username password vpnuser 0 x
!
!
LAN controller 0
atm mode
Annex symmetrical shdsl DSL-mode B
!
interface Loopback1
Gateway SSL dhcp pool address description
IP 192.168.250.1 255.255.255.0
!
interface Loopback2
Description address IP VPN SSL
IP 10.10.10.1 255.255.255.0
route PBR_SSL card intellectual property policy
!
interface BRI0
no ip address
encapsulation hdlc
Shutdown
Multidrop ISDN endpoint
!
ATM0 interface
no ip address
load-interval 30
No atm ilmi-keepalive
PVC KPN 2/32
aal5mux encapsulation ppp Dialer
Dialer pool-member 1
!
!
interface FastEthernet0
switchport access vlan 100
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
LAN description
IP address 192.168.10.254 255.255.255.0
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1300
!
interface Vlan100
Description KPN ADSL 20/1
DHCP IP address
NAT outside IP
IP virtual-reassembly
!
interface Dialer0
Description KPN SDSL 2/2
the negotiated IP address
IP access-group INTERNET_ACL in
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
Dialer-Group 1
PPP pap sent-username password 0 x x
No cdp enable
!
IP local pool sslvpnpool 192.168.250.2 192.168.250.100
IP forward-Protocol ND
IP http server
local IP http authentication
IP http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
pool nat SSLVPN SDSL 10.10.10.1 IP 10.10.10.1 netmask 255.255.255.0
IP nat inside source static tcp 10.10.10.1 443 interface Dialer0 443
IP nat inside source static tcp 10.10.10.1 80 Dialer0 80 interface
IP nat inside source overload map route NAT_ADSL Vlan100 interface
IP nat inside source overload map route NAT_SDSL pool SSLVPN SDSL
IP route 0.0.0.0 0.0.0.0 x.x.x.x
IP route 0.0.0.0 0.0.0.0 Dialer0 10
!
INTERNET_ACL extended IP access list
Note: used with CBAC
allow all all unreachable icmp
allow icmp all a package-too-big
allow icmp all once exceed
allow any host 92.64.32.169 eq 443 tcp www
deny ip any any newspaper
Extended access LAN IP-list
permit ip 192.168.10.0 0.0.0.255 any
refuse an entire ip
!
Dialer-list 1 ip protocol allow
not run cdp
!
!
!
!
NAT_SDSL allowed 10 route map
match the LAN ip address
match interface Dialer0
!
NAT_ADSL allowed 10 route map
match the LAN ip address
match interface Vlan100
!
PBR_SSL allowed 10 route map
set interface Dialer0
!
!
control plan
!
!
Line con 0
no activation of the modem
line to 0
line vty 0 4
privilege level 15
transport input telnet ssh
!
max-task-time 5000 Planner
!
WebVPN MyGateway gateway
hostname d0c
IP address 10.10.10.1 port 443
redirect http port 80
SSL trustpoint TP-self-signed-3964912732
development
!
WebVPN install svc flash:/webvpn/anyconnect-dart-win-2.5.0217-k9.pkg sequence 1
!
WebVPN install svc flash:/webvpn/anyconnect-macosx-i386-2.5.0217-k9.pkg sequence 2
!
WebVPN install svc flash:/webvpn/anyconnect-macosx-powerpc-2.5.0217-k9.pkg sequence 3
!
WebVPN context SecureMeContext
title "SSL VPN Service"
secondary-color #C0C0C0
title-color #808080
SSL authentication check all
!
login message "VPN".
!
Group Policy MyDefaultPolicy
functions compatible svc
SVC-pool of addresses "sslvpnpool."
SVC Dungeon-client-installed
Group Policy - by default-MyDefaultPolicy
AAA authentication list sslvpn
Gateway MyGateway
development
!
end
Any suggestions on where to look?
Hello
It works for me. When the client tries to resolve the fqdn for the domain specified in "svc split dns.." he will contact the DNS server assigned through the Tunnel. For all other questions, he contacts the DNS outside the Tunnel.
You can run a capture of packets on the physical interface on the Client to see the query DNS leaving?
Also in some routers, DNS is designated as the router itself (who is usually address 192.168.X.X), if you want to make sure that assigned DNS server doesn't not part of the Split Tunnel.
Naman
-
Help license SSL Info failover ASA 8.2 8.3
Hello
I have a question about lincense.
I have a 8.2 in HA cluster, active failover.
I bought 100 VPN SSL lic 4 months ago for ASA active and ensures 100 lic for ASA in mode.
So on each firewall there is a lic for 100 SSL VPN.
If I switch to 8.3 the ICA became 200 or even 100 assets and 100 for emergency unit?
because I've read in this doc
Here "How failover Licenses combine" that there is the possibility that the linces can became a lincense cluster.
Can you help me? Is there someone who try this feature?
Thank you very much.
Yes, you are absolutely right. With version 8.3, the license will be mixed, and you'll have 200 user license to use. But please please be advised that for example if you have 500 user license on each, with a combined of 1000 user license, and the ASA platform only supports the 750 user license, you are limited to the user license only 750.
PS: If you want to upgrade to version 8.3, please check changes of NAT and ACLs. NAT changed completely with the concept of double NAT and NAT object network.
Hope that answers your question.
-
Hello
I have configured the client SSL VPN on SAA. I'm able to establish SSL VPN with the ASA and obtaining the IP address of subnet defined (CorporateVPN 172.16.0.100 - 172.16.0.110). But when I try to ping inside the property intellectual treats which is 172.16.0.1 and other machine in the range LAN getting loss of packets to the remote machine.
What could be the problem?
Below is the configuration of the SAA.
ASA Version 7.2 (1)
!
Cisco - ASA host name
test.com domain name
activate the password password
names of
DNS-guard
!
interface Ethernet0/0
Description connected to ISP
nameif outside
security-level 0
IP address "public IP".!
interface Ethernet0/1
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/2
Description connected to the local network
nameif inside
security-level 100
172.16.0.1 IP address 255.255.255.0
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 0
IP 192.168.1.1 255.255.255.0
management only
!
2KFQnbNIdI.2KYOU encrypted passwd
boot system Disk0: / asa721 - k8.bin
passive FTP mode
clock timezone GMT 3 30
management of the DNS domain-lookup service
DNS server-group DefaultDNS
Server name 203.123.165.75
test.com domain name
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
mask 172.16.0.100 - 172.16.0.110 255.255.255.0 IP local pool CorporateVPN
IP verify reverse path to the outside interface
IP verify reverse path inside interface
no failover
ASDM image disk0: / asdm521.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 172.16.0.0 255.255.255.0
Route outside 0.0.0.0 0.0.0.0 Gateway 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
internal GroupPolicy1 group strategy
attributes of Group Policy GroupPolicy1
Protocol-tunnel-VPN IPSec l2tp ipsec webvpn
WebVPN
enable SVC
SVC Dungeon-Installer installed
time to generate a new key of SVC 30
SVC generate a new method ssl key
internal Netadmin group strategy
Group Policy attributes Netadmin
Protocol-tunnel-VPN IPSec l2tp ipsec webvpn
WebVPN
Required SVC
SVC Dungeon-Installer installed
time to generate a new key of SVC 30
generate a new key SVC new-tunnel method
dpd-interval SVC 500 customer
dpd-interval SVC 500 gateway
username cisco password encrypted privilege 15 ffIRPGpDSOJh9YLq
attributes username cisco
VPN-group-policy Netadmin
http server enable 444
http 192.168.1.0 255.255.255.0 management
http 0.0.0.0 0.0.0.0 outdoors
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
attributes global-tunnel-group DefaultWEBVPNGroup
address pool CorporateVPN
tunnel-group NetForceGroup type webvpn
attributes global-tunnel-group NetForceGroup
address (inside) CorporateVPN pool
address pool CorporateVPN
Group Policy - by default-Netadmin
No vpn-addr-assign aaa
No dhcp vpn-addr-assign
Telnet 192.168.1.0 255.255.255.0 management
Telnet timeout 10
SSH timeout 5
Console timeout 0
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
WebVPN
allow outside
SVC disk0:/crypto_archive/sslclient-win-1.1.1.164 2 image
enable SVC
context of prompt hostname
Cryptochecksum:13f5616c7345efb239d7996741ffa7b3
: endYes, 'inside access management' is only to manage/ping of the SAA within the interface. Without this command, they would still be able to access the internal network. This command is only used to manage the SAA within the interface itself.
-
not having to ssl vpn login prompt
Hi all
This is the configuration for SSL vpn on our ASA 5510. . If we made the reference to the site configuration, we are unable to get the login prompt. could you please check and suggest you do the work of SSL vpn
Configuration
===========
WebVPN
allow outside
back to url-list Test webvpn
import webvpn url-list SSL_Bookmarks disk0: / tmpAsdmImportFile1646955469
delete /noconfirm disk0: / tmpAsdmImportFile1646955469
internal SSL_users group strategy
attributes of Group Policy SSL_users
VPN-tunnel-Protocol webvpn
WebVPN
the value of the URL - list SSL_Bookmarks
type tunnel-group SSL_VPN remote access
attributes global-tunnel-group SSL_VPN
Group Policy - by default-SSL_users
Group-RADIUS authentication server
attributes of Group Policy SSL_users
VPN-tunnel-Protocol svc webvpn
tunnel-group SSL_VPN webvpn-attributes
enable AnyConnect group-alias
WebVPN
tunnel-group-list activate============================
Version
======
ASA-5510-1 # sh ver
Cisco Adaptive Security Appliance Version 8.2 software (1)
Version 6.2 Device Manager (1)Updated Wednesday, 5 May 09 22:45 by manufacturers
System image file is "disk0: / asa821 - k8.bin.
The configuration file to the startup was "startup-config '.ASA-5510-1 up to 57 days 9 hours
Material: ASA5510, 256 MB of RAM, processor Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256 MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024 KBHardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0)
Start firmware: CN1000-MC-BOOT - 2.00
SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.04
0: Ext: Ethernet0/0: the address is 0027.0d38.034e, irq 9
1: Ext: Ethernet0/1: the address is 0027.0d38.034f, irq 9
2: Ext: Ethernet0/2: the address is 0027.0d38.0350, irq 9
3: Ext: Ethernet0/3: the address is 0027.0d38.0351, irq 9
4: Ext: Management0/0: the address is 0027.0d38.0352, irq 11
5: Int: internal-Data0/0: the address is 0000.0001.0002, irq 11
6: Int: internal-Control0/0: the address is 0000.0001.0001, irq 5The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 100
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: disabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
The VPN peers total: 250
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect for Linksys phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabledThis platform includes an ASA 5510 Security Plus license.
Serial number: JMX1350L04D
Activation key running: 0xef04c544 0xf4999c16 0xf4c19950 0x85684c50 0x442c3292
Registry configuration is 0x1
Modified configuration of enable_15 to 06:55:11.349 UAE Thursday, November 18, 2010
ASA-5510-1 #.===================
Thanks in adavnce
You can get the activation key for 3des from the license page (it's free):
https://Tools.Cisco.com/swift/licensing/PrivateRegistrationServlet?DemoKeys=Y
(Click on Cisco ASA 3DES/AES license)
It can work with just, however, your browser might not support SOME. The browser asks political there and see if ASA has set up, but I know that a lot of the new browser will not load more, but feel free to try.
-
How SSL VPN packages for two ASAs clustered licenses
Hi all!
If I have installed two Cisco ASA 5550 (ASA5550-BUN-K9) in failover mode, which I know support only 2 concurrent sessions of SSL VPN and you want to upgrade my boxes to support 15 AnyConnect SSL VPN sessions, how many licenses packages I need to buy?
An ASA5500-SSL-25 for both boxes or two ASA5500-SSL-25 for one per box?
Depends on what version of ASA you are running.
If you are running version 8.3 and above, then you just buy 1 ASA5500-SSL-25 for a failover pair and it would work. If you buy 2 ASA5500-SSL-25, one license per box in failover pair, then the license gets grouped into 50 SSL user license.
Here is the license information for ASA version 8.3 for failover pair:
For ASA running version 8.2 and below, you are required to buy 2 ASA5500-SSL-25 (one of each ASA in the failover pair) as the license should be exactly the same for the pair to failover to work, in the earlier version of the SAA.
Hope that makes sense.
-
Hello
I have 2 5510 ASA and I'm in a pinch with needing a failover ASA to implement. I have an ASA test I put in as a firewall waiting in an active scenario / in sleep, and this ASA a user 10 SSL VPN license applied. My ASA primary I'll put this in place with only 2 standard user and fails it of Wizard config HA when I run through it. The message I get is "Test of compatibility of the license for many clientless SSL VPN peers has failed." How can I deactivate the license 10 user on my unit of analysis so I can bring it failover?
The two ASA have a license of SecPlus.
Thanks for any help,
Brett
Keep your current activation key you can reapply after your tests, and request a new activation key of [email protected] / * / unlicensed SSL VPN to test your failover.
-
Hello
We have a customer with the ASA license.
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 150
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
Total of the VPN peers: 750
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect for Linksys phone: disabled
AnyConnect Essentials: enabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabledBut when I look at the Tracking tab of the VPN, they have 40 to 50 VPN SSL with client sessions active at any given time. Is this correct or does pass the license?
Hello
The license shows up, you can have 2 SSL VPN peers.
the following link gives you all the details of the available licenses. Please choose according to your requirement.
Kind regards
Anisha
P.S.: Please mark this message as answered if you feel that your request is answered.
-
I use the SSL VPN in time. I just noticed that when I tried to pass by I logged in and tap on connect, but now I get the error: virtual failure of execution of the Passage. I tried another computer that is already running IE9 and I had no problem getting in and using my office remotely over SSL.
IE11 isn't working? or what should I be looking at.
router is the latest firmware.64-bit is IE only.
IE10 and 11 are disasters, when it comes to compatibility and how it manages Active-X controls. I'm not aware of any SSL VPN with IE10/11 suppliers.
You can try Firefox. I can get the java applet to install, but the roads do not work for me.
Contact support directly and express your concerns.
You can always use IPsec client software.
-
RVL200 ssl vpn, I'm not able to access resources network or ping of the Home Office
I had installed a Linksys router using port forwarding to allow remote access to the server desktop remotely. I had some problems with it and I've always wanted a vpn connection to the office, but I could not ' operate. So I bought the RVL200 after that I read on it and ssl vpn.
I have the router installed right after the modem cable to the office. I'm able to hit the external ip address of the House. I have the router to access the Server Active directory for connections. The connection works fine, all the different active directory accounts have access to the vpn through this. I am also able to make administration of the router remotely. I am able to connect to the vpn and get connected virtual passage. The icon in the systray says that everything is good. With all this, I'm not able to ping every address on the remote network. I can't reach all the network resources as \\pdrserver\irms or my print server ip address. I can't use network XP Favorites to find anything on the remote network.
Someone has an idea what I am doing wrong? I appreciate the help.
I thought about it. I was using the same IP for the home and office. It was confusing. I changed my IP to another system. Home office and now 12.4.4.X now 11.4.4.X. After that, everything worked as it should. Readers without mapped problem, ping remote computers. I could access the remote print servers. Works well. So make sure that you do not use the same IP addresses on both sides of the VPN.
Maybe you are looking for
-
I am connected to my old Apple ID on my MacBook, but have a different, new ID, apple on my iPhone. I have thousands of photos on my Mac that I'm terrified of losing if I change. Is it possible to transfer my ID apple without them all removed on my Ma
-
Stop asking me to update the plugins - you are more troublesome
I'm generally upset with Mozilla because there is nobody on the phone and discuss issues. You make changes without my permission and then expect me to find answers online. Soon you will be able to lead me to Microsoft.
-
HP ENVY 1105dx m6: Beats Audio driver problems
Hi I'm having is continuous when I go to listen to music, that the volume fade in and out by itself it starts off normal then out of nowhere the volume will drop or fade on what going on with the speakers of the laptop itself and when I plug in a cor
-
Portege R600 cannot detect Toshiba Slim Port Replicator II PA3603U-1PRP
Hi all My Toshiba laptop is Toshiba Portege R600 D260 with Toshiba PA3603U - 1PRP Slim Port Replicator II (REF: PA3603U-1PRP), the problem is "PA3603U-1PRP Toshiba Slim Port Replicator II can't detect the USB Port. I wonder that PA3603U-1PRP Toshiba
-
Windows Messenger does not work
My msn messenger has stopped working. I started getting a message saying "Windows messenger has stopped working. A problem caused the blocking of the program works correctly. Windows will close the program and notify you if a solution is available. "