Start on successful response video

Similar Questions

• I have synced clips successful but video and audio are not visible until it is developed to the timeline. Returned results completely black film without sound. Any tips?

  I have synced clips successful but video and audio are not visible until it is developed to the timeline. Returned results completely black film without sound. Any tips?

  Please give as much information as possible on your support. The video and audio works in QuickTime player? What are the specifications of media?

• Computer has a blue screen crash about 5 minutes after each start up successful

  Computer has a blue screen crash about 5 minutes after the start of successful with the error msg: Stop 0x0000008E (0xc0000005, 0xb7e4571d, 0xb1440748, 0x00000000) Atapi.sys-address b7e4571d base at b7e3b000 datestamp 48025396. Any help is appreciated.

  Hi jason12685,

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?

  Method 1

  Possible causes of this error include the following:

  • Drive hard damage
  • Problems of material General configuration with the BIOS, memory, hard drive, or with other devices
  • Incompatible device driver
  • Incompatible software

  Check out the articles below and try the steps mentioned, check if it helps.

  You receive a random "0x0000008E" error message on a blue screen in Windows XP

  http://support.Microsoft.com/kb/827663

  General troubleshooting for an error message that you receive randomly in Windows XP: "Stop 0x0000008E"

  http://support.Microsoft.com/kb/945658

  Method 2

  I would also say that you update all the drivers for hardware devices on the computer by visiting the manufacturer of the computer or the device manufacturer's Web site.

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

• Programs can not be started, or no response after the computer was not awake mode "Eve"

  Dear Sir.

  My lap top is under the VISTA system. Now the problem is that all programs can not be started or no response after the computer was not awake mode "Eve". I have to restart the computer to recover the computer to normal state.

  Please please let me have your advice to return to my email address: * email address is removed from the privacy *.

  Thank you very much!

  Eric

  Hi Eric,.

  You can follow these steps:

  Step 1: perform a clean boot to verify if an application or service is causing the problem.

  See this article for more information on the clean boot:
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
   http://support.Microsoft.com/kb/929135

  Steps to perform a clean boot:
  a. click the ORB start on your desktop
  b. type msconfig in the search box and press ENTER.
  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.
  c. in the general tab, click Selective startup.
  d. under Selective startup, clear the check box load startup items.
  e. click on the Services tab, select the hide all Microsoft Services check box and then click Disable all.
  f. click OK.
  g. When prompted, click on restart.

  NOTE: Please check that you start the computer in normal mode after a repair. Follow step 7 article.

  Step 2: Configure the power settings for keyboard, mouse, and other devices.

  a. Click Start, click Control Panel, hardware and sound, and then click keyboard.
  b. click on the Hardware tab, and then click the properties button.
  c. click Change settings.
  d. click the power management tab and verify that the allow this device to wake the computer is selected.
  e. If "Allow this device to wake the computer" was not selected, select it and click OK.
  Follow the same steps for the mouse as well.

  If the problem persists, disconnect all non-essential devices (printers, scanners, USB drives). Restart the computer with only the original mouse, monitor, and
  connected keyboard. If this solves the problem of sleep/wake, one of the devices was causing the problem. Replace a device at a time and test to see if the
  problem occurs again. Continue adding devices and testing until you find the device that causes the problem.

  Refer to this article for additional troubleshooting steps.

  
  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista:
  http://support.Microsoft.com/kb/950686

  Kind regards
  Afzal Taher - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problem starting Windows 8 (associated with quick start + Intel Smart Response Technology SSD cache)

  Hello
  I have a problem with the fast start-up of Windows 8. When I shut down my PC everything works fine, but when I turn on the PC, Windows will load until a certain point and then suddenly start screen appears again. The second departure is always successful.

  I discovered, when I turn off the Quick start, the computer starts without error on the first attempt. It goes the same for when I disable Intel Smart Response Technology (SSD cache). There are no problems when I use Hibernate mode.

  Recently I did a BIOS update, so I don't know if there is a setting in the BIOS that is may cause this error?

  Thanks in advance for any help!
  Martin

  Hi Martin,

  Glad to know you solved the problem. Thanks for sharing of the resolution, because it would help the other members of the community to the same question.

  Please do not hesitate to answer, in case if you need help or information on this issue.

• HP 15-af131dx: computer HP laptop does not start after update AMD video drivers

  Hello, my laptop HP 15-af131dx would not start after I have updated to the latest video drivers from AMD. After update, my phone was really slow, so I decided to restart it. When I tried to start up, most of the time, she would get to the windows logo with the symbol of loading under it and crashed. Sometimes arise windows recovery, but using it would only make it appear an error message. After a few tries, I was able to boot into windows safe mode and restore my video drivers. This corrects the problem, but I would like to know why this is happening and if the update of my video drivers by importing.

  . Hi @HPlaptop5,
  
  I hope you enjoy your visit to the HP's Support Forums. I understand that you have a problem with video drivers. I'll be happy to help you.

  You can also find your drivers to support.hp.com.

  The latest HP driver released was Version 15.201.1101.0 Rev.A release: January 29, 2016.

  I do not update my driver unless I have a video problem.

  Please keep me informed of the progress of things.

  If you need help, let me know and I will gladly make all that I can to help you.

  Please let me know if that solves the problem by marking this post as "accept as a Solution.
  To simply say thank you, click the Thumbs up below!

  Thank you.

• HP elite m9340f: do not start after replacing the video card. Repeating short and long beeps. Help!

  Hello: I have a m9340f HP Pavilion Elite aged five years, under vista. He had a problem with video output, so I bought a new video card and exchanged out them. but now, the computer does not start and made that one short beep and long stretch trying to power upward.  I double checked all connections and they are all good.

  Please help me if you know what the problem is.  Thank you... KarlJ

  I found that 1 beep short, followed by a long beep indicates a memory failure, try reinstalling your memory

• Computer does not start with the new video card

  Hello

  I have hp pavilion 500-277cb and I love it, but it won't work with my new video card

  The video card is
  Sapphire ATI over-pants 2460

  I heard 6 beeps and I turned off safe and active start legacy. It does not beep, but it is not start either, just black screen.

  It seems to me to have the latest version of the bios and windows 8

  What can I do else?

  Thank you very much

  Best,

  Korhan

  Hi JM,

  Did you remove the Intel HD graphics drivers prior to installing the ATI graphics card?

  Your PC comes with one of the following built-in Intel graphics drivers:

  • Graphics Intel HD 4400 (GT2)

• Does not start after installing new video card

  Hello, I have a desktop H8-1284, and the video card went a few days ago. So I bought a video card Geforce GTX 650, and after installing the card and the computer starts, it hangs just at the start of the HP logo screen. So I put an old geforce 8800, and she starts without a problem. When I try the new card Geforce GTX 650, the same thing, just hangs at the splash screen.  I checked the bios and it doent seem to be something there that can help wouild. My diet is 460 w, and the new map needs of 400 w, any help will be greatly appreciated

  Hello

  Most of the cards PCI-E 3.0 are retro-compatible with the PCI-E 2.0 slots.  However, in order to get the PCI-E version 3, you must use a processor Ivy Bridge.  Look at these specificationsfor a typical NVIDIA GTX 650.

• How to start and stop the video capture in a state machine

  Hello

  I am a student of neuroscience and this is what I try to do: 1) trigger a camera to GigE (200 FPS), 2) start the video capture, 3) triggers a light that stays on for x milliseconds, 4) trigger a valve that will blow an air puff, 5) stop the tone and the valve at the same time and 5) stop the video capture 1 second after 4). For this, my VI is a state machine, with a State for each trigger (ex, 1 State for trigger camera 1 State of light of trigger, ect) and a statement to "stop" and a "time-out State." Everything worked except the video acquisition - the program could trigger the camera but only acquire a frame, because it was not running in a while loop and this is my first question: for an acquisition video is it always necessary to have a while loop?
  I guess the answer is Yes, so I built a loop of 'consumer' for the camera. A queue of the pre-trial 'trigger camera' in the loop of producer, I was then able to start the video capture, but now the problem is to stop it at the right time. I have an another queue in the State of 'stop' in the loop of the producer, but is not able to start the State 'stop' in the loop of consumer, I think that maybe it's because the loop of consumer gets "stuck" in the whole loop.

  I hope you can help me, the VI is attached. Thank you!

  Hello

  First of all, in your loop producer: STATE 'Stop', you use the flushing line, then there is no need to use 'item queue at the opposite end. You can use the enqueue function.

  Secondly, you said "I moved the command stop inside the while loop as you said, but it did not work. But if you look closely, you moved "Enqueue function" inside the while loop. Instead you should use Dequeue function. Please, look at the picture I posted an orderly manner.

  And remove the circled (i.e. function. Enqueue function loop of consumption, where I wrote 'Why stop here').

  Try now.

• Why no games start after successful installation?

  I have recently completely reformat my hard drive and reinstall XP SP3 - since then no games will start for example. Crysis2, Borderlands, Far Cry, etc. Most of them just install apparently successfully, but when I run get them the hourgalss for 10 seconds and then nothing. The only exception is Borderlands that comes up with the following error message:

  C:\Program Files\2K Games\Gearbox Software\Borderlands\Binaries\Borderlands.exe

  This application has failed to start because the application configuration is incorrect. Reinstalling the application may fix this problem.

  >>

  All of these games used to run fine, my material has not changed, and since reinstalling XP SP3, I have downloaded and installed the latest NVIDIA drivers Creative etc.

  Most graciously accepted ideas

  Fraser

  Hi fraserwood,.

  ·         You have an installed antivirus program?

  Method 1: Temporarily disable the antivirus on the computer program and check if it helps. If it works, you may need to check the settings of the program.

  Note: Check that you activate your anti-virus protection on the computer back after you complete these steps. It is not recommended to disable these settings on the computer. It's just to solve the problem.

  Method 2: Make sure you have the latest updates of Windows installed. To update the most recent and then try to install the games.

  Windows Update

• computer does not start until montor no video signal message

  Dvd player unpluging and pluging into computer slave dvd powered down, that I went back to the orignial dvb car, won't boot upward and montor reads no video signal.

  The computer feeds also on orange with led op. running xp SP3

  Hi rdb 1949,.

  • Are you facing the question after you have connected the DVD player to the computer?

  This error message occurs generally if the faulty monitor or video card in the computer driver is damaged.

  I suggest that you start the computer to activate the VGA Mode or mode safe mode and check if the computer starts very well.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Also, connect another monitor to the computer and check if it works.

• The Active Directory Connector - create user SUCCESS response code

  Details of the environment: Oracle® Fusion Middleware 11 g Release 2 (11.1.2.2.0)

  Build IAM_11.1.2.2.0_GENERIC_131230.2258

  I have a task of personalized process that puts into service a right to the user and notifies the credentials of the user to the Manager.

  These tasks are conditional and configured to be triggered only when Create User returns the response as a SUCCESS code.

  The more bizarre behavior, these process tasks are triggered before (update of the value of the UID in the form of process OR before the response code defines SUCCESS) AND after (the user is created in AD).

  Anyone seen this?

  Questions: Email Notifications are going very well, but when set up right, account was not created in IOM.

  Share your ideas-thank you

  Try to set the task of the user to create a previous task for each of the other ones that must run first.  You can also add additional tasks that must be completed first too.

  -Kevin

• Preview Ram CC starts immediately audio and video later

  I'm having a problem where the ram preview will start as planned, but plays only the audio and the video will start maybe a second later.

  No idea what this could be?

  Thank you

  Felix

  OS X 10.10 AE CC 2014

  This is a bug introduced by Mac OS x v10.10 which we by-passed in the After Effects version out soon.

• While on youtube after 1 download success, 'no videos on this page to download' does no sence for me since I'm still on youtube!

  I don't understand why he would not see the videos on youtube. makes no sense because I was just downloading ok, now, he won't have to see ALL the videos.

  Hello

  The reset Firefox feature can solve a lot of problems in restaurant Firefox to its factory default condition while saving your vital information.
  Note: This will make you lose all the Extensions, open Web sites and preferences.

  To reset Firefox, perform the following steps:

  1. Go to Firefox > help > troubleshooting information.
  2. Click on the button 'Reset Firefox'.
  3. Firefox will close and reset. After Firefox is finished, it will display a window with the imported information. Click Finish.
  4. Firefox opens with all the default settings applied.

  Information can be found in the article Firefox Refresh - reset the settings and Add-ons .

  This solve your problems? Please report to us!

  Thank you.