Start the machine in background mode

Similar Questions

• When I start the machine, continuous hard drive work for almost 1/2 hour, meanwhile if I open a program, the machine runs very slowly. Help solve the problem please

  I have wndow XP Home edition service pack 3 installed on my lap top. When I start the computer the hard drive continues to work for almost 1/2 hour; Meanwhile, if I open IE, or any program, the machine runs very slowly and I just can not open the program up until the drive hard light is off. Please help solve the problem

  How much RAM you have on your system? (Right click on "My Computer"-> properties)

  As a general rule, Windows XP does not work well if you have less than 1 GB or more of RAM.  What usually happens is that your RAM capacity is exceeded leading to overflow on virtual memory (the drive) to compensate for the need of RAM in the computer.  This causes your system to beat on your hard drive and slow down your system.

  If this is your problem, the options are to increase the RAM on your system or decrease the non-essential programs that launch at startup on your computer using a tool like Autoruns.

  HTH,
  JW

• off frequency message error when start the computer in normal mode

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hey pamyres

  you say not what led to what happens

  You must give information here to get help

  try a restore of the system in safe mode before your problem

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Walter, the time zone traveller

• Connected network drive doesn't remember credentials if must connect whenever I start the machine even when I click on the button to recall the details.

  Using windows 7 I have a drive NAS that I need to connect manually whenever my machine that we start - I want that he remember details of connection and do it automatically at startup of the machine because it is also used by my wife and I want auto backup to run.

  Using the Credential Manager in Windows 7 to remember the username and password for your NAS drive if she don't remember automatically.

  Go to start / Control Panel / user accounts and family safety / Credential Manager

  On the right side, just below where it says "Windows credentials" select "add a Windows credential.

  In the first box, enter the name of your NAS server.

  User name in the second box and your password for the server in the third area.

• Error while starting the machine upward

  Hello

  recently, I have reinstalled my ESX server with ESXI 5.5 test. Previously, I was running ESXI 5.0. I saved all the you VM on my PC. Then I restored the ESXI storage files. I added their return to inventory (right click on VMX file/add to the inventory), but one of the machines is not started. There is an error:

  

  Could you please advise me how to solve the problem?

  Thank you much in advance.

  
  

  If the problem has been resolved? Are you able to turn on the virtual machine?

• How to start the machine after export OVF?

  I'm under OVF tool to export a virtual machine (ESXi 5.0) from a command line. One of the options will stop the virtual machine before export that works very well. Y at - it an option to automatically start this machine after export?

  Thank you very much!

  The question was a response 1038043 KB

  Thank you for helping.

• Cannot start the system in safe mode - F8 no response

  Try to get to SAFE mode reset earlier date (profile does not load), but by pressing or hit F8 during the power upward has no effect and portable continuous screen PW rather than presenting the start menu (where I can choose to boot in safe mode)

  You can enter BIOS with F2 at startup?

  You may have turned on option quick start?
  

• 1F1 Saellite C660 - cannot start the machine?

  Ive had machine about 6 months. Tempted to put on yesterday, it seems to start as usual, the Toshiba screen flashes up (where he mentions F 2 and F12 for menus) and then the screen goes all white and nothing happens. Forgive me, I'm a novice and struggling to find what to do. Can anyone offer advice please?

  Hello

  You can access the BIOS?
  Immediately after the laptop has been powered, press F2.
  In the BIOS, please check if the HARD drive is listed and recognized.
  If the HARD drive is not listed, this means that the HARD drive is not recognized by the BIOS, and that means that it s faulty.

  You can also check if you can run HARD drive recovery.
  Switch on the device, press F8, and then select Repair my computer, then choose disk HARD recovery. This would reinstall the OS and fix the laptop back to factory settings.

• start the computer in safe mode

  hard drive detected problem iminent failure press F1 key to continue... After pressing F1 computer won't start in safe mode

  so I check apparently I solve the problem. I run a system check and all is fine... I reboot my computer and I get: problem hard drive detected iminent failure press F1 to continue... boots up in safe mode only... the changes ive made did nothing because when the computer reboots, it starts again in SafeMode only. but with the networking and database drivers and the DCs as startup options. nothing seems to stick to restart the computer for the changes to take effect.

  Hello

  'problem detected hard disk iminent failure '.

  The hard drive is faulty

  Back up your data > buy a new hard drive > reinstall the operating system.

  To be sure, this is the problem do the following:

  Go to the website of your computer manufacturer > find specifications of hardware in your computer (hard drive) > access the Web Hard Drive from the manufacturer site > download their diagnostic software > make a Bootable disc > test your hard drive.

  See you soon.

• Cannot defragment the hard drive AND cannot start the computer in safe mode

  I have been unable to defragment my hard drive because it tells me that chkdsk /f planned.  I tried manually works in command mode nothing works.  I was advised to try to start up in safe mode, but when I do that all I get is a screen of command lines, and my computer freezes there.  What I'm doing wrong and what I can do differently?

  If you try to defragment a volume and see a message like this:

  Disk Defragmenter has detected that Chkdsk is scheduled to run on the volume: (c :))
  Please run Chkdsk /f.

  This means that the volume (disk) that you want to defragment was marked 'dirty' XP.

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  You have a genuine XP installation CD bootable, which is the same Service as your installed Service Pack (this is not the same as any recovery CD provided with your system)?

  You can check the status of your bit of impurity from a command prompt window.

  To do this, click Start, run and enter in the box:

  cmd

  Click OK to open a command prompt window.

  For example, to query the bit of impurity on drive C, type:

  fsutil dirty query C:

  The sample output:
  Volume c is dirty
  Volume C: is dirty

  Is the volume of your sale or it is not dirty?

  The only way to disable the on a volume's dirty bit is to run chkdsk with error correction.

  You can click on start, run and enter in the box:

  Chkdsk /r

  Click OK and answer Yes to schedule the chkdsk next time XP restarts, restart your system and keep your fingers crossed that the chkdsk /r clears the dirty bit (you may need to run once or twice).

  If who disobeys, then you will need to start in the XP Recovery Console and run the chkdsk /r from there.

• start the computer in normal mode with settings in safe mode

  I restarted my computer from malwarebyes in safe mode and when he started he uses in normal safe mode settings. I tried to use the last good settings and she didn't date there. no old parameters. No idea how to get back to normal settings?

  You can either restore your system to a previous state.
  If this does not work, have to "msconfig" (run-> msconfig)
  In the new window, in the "general" tab, you can see three options like normal startup, diagnostic and selective upward.
  Select normal startup. then restart apply.and.
  That's all.

  Thank you.

• I tried to start the computer in safe mode, nothing works. All of a sudden my icon text in paint is dark. Why?

  Found the answer... the text bar is still gray but I was able to unlick

  in the toolbar and I was able to add text.  Not sure, maybe "text".

  the button was grey all along?  I don't think, but I can choose only three of

  the four options that allow a check mark in the view menu: toolbar, color and the State.  The text

  has a check, but it is gray, cannot be enabled or disabled.  Maybe I just never noticed it before.  Could

  Add text by clicking on the toolbar tools, then reclicking thereon.  Odd.  It works and that's all that I needed.

  Hi Gail Harris,

  Safe mode is an option of troubleshooting for Windows that starts your computer in a limited State. In safe mode only basic files and drivers needed to run Windows are started.

  For more information, please visit the links.

  What is safe mode?

  How does safe mode?

• Start the camera in manual mode?

  If you can make the camera to start immediately in manual mode?

  Issue edited by Rickard

  It is not possible when you use the camera button, but if you type "Camera" in the app drawer or he will go to manual if that's what you used the last time the home screen.

• Satellite P200 - after the BIOS update I can't start the machine

  After the BIOS update I can't boot the laptop because the system doesn't recognize the relecommunicarions password.

  Before updating the password is 0000.
  After when I try to set the password incorrect password start apeeras

  The BIOS password can only be removed from an authorized service provider. So I think that there is no other way.

  On the Toshiba site, you can search the nearest:
  http://EU.computers.Toshiba-Europe.com

• Yoga 2 pro: a mouse work with the machine in tablet mode?

  just curious, a pre purchase question... will the 2 yoga works with a mouse inverted when opened and a «tablet "mode?»

  Thank you.

  Yes, its only the 'edge' mouse and keyboard which is disabled.