State of TCP Bypass
I searched in the new TCP State ASA 8.2.1 bypass feature and I have a few questions that I can't find information about in the docs:
1 Bypass State TCP removes all stateful inspection? That is to say that I must allow traffic from response in the ACL
access-list on permit tcp any any eq www
access-list on permit tcp any eq www everything
access-list on permit udp any any eq field
access-list on permit udp any eq field all
2. the State of docs who are unaware of the TCP State can be enabled for some connections. Is request inspection disabled for all connections, or just for specific connections have been implemented for the avoidance of State TCP?
It removes all the statefull inspection. By default, all traffic that passes through the Adaptive security device is inspected using the Adaptive Security algorithm and either allowed to pass or a fall is based on the security policy. The Adaptive security device optimizes the performance of firewall to check the status of each package (what is a new connection or a connection?) and assigning the path of session management (a new connection SYN packet), the fast path (an established connection), or the path of control plan (Advanced inspection).
Inspection of the application is not supported in bypass State TCP as enforcement requires the incoming and outgoing traffic to pass through the same Adaptive security appliance, so control of the application is not supported with by-pass TCP State.
Tags: Cisco Security
Similar Questions
-
Original title: Office of Microsoft Outlook 2000 does not open.
Error message States "A TCP/IP error occurred while trying to send data to the Server Error 0x800ccc13 #
Hi John,.
1. what operating system is installed on your computer?
2 How long have you been faced with this problem?
3. don't you make changes on your computer before this problem?
Reference: Outlook 2000 Solution CenterPlease post back and we do know.
-
Unable to reach the other subnet to VPN
I need the vpn users to access the resources of the SITE-A. VPN access all the resources of the SITE B but unable to reach all servers in A SITE. ASA, I can ping servers A SITE without any problem. I tried to configure the tcp-bypass (http://packetflow.io/2014/03/asa-hairpinning-and-tcp-state-bypass.html) but still not able to reach A SITE. I also tried the crossed this site (https://nat0.net/cisco-asa-hairpinning/) and still no luck. Any idea is appreciated. I can provide SITE-B router config if necessary.
DNS-guard
mask pool POOL-VPN-IP 10.240.25.15 - IP 255.255.255.0 10.240.25.50
!
interface Ethernet0/0
Speed 1000
full duplex
nameif OUTSIDE
security-level 0
IP 10.0.0.1
!
interface Ethernet0/1
No nameif
no level of security
no ip address
!
interface Ethernet0/1.10
VLAN 10
nameif inside
security-level 100
IP 172.18.83.250 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
!
boot system Disk0: / asa916 - k8.bin
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS domain-lookup OUTSIDE
domain-search DNS inside
DNS server-group DefaultDNS
Server name 172.18.83.10
Server name 172.18.83.11
Name-Server 4.2.2.2
domain.com domain name
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
the object OBJ - ANY network
subnet 0.0.0.0 0.0.0.0
service object MSTSC
service destination tcp 3389 eq
network of the VPNPOOL object
10.240.25.0 subnet 255.255.255.0
object SITE-B network
172.18.83.0 subnet 255.255.255.0
object SITE-A network
172.18.80.0 subnet 255.255.255.0
object-group, INTERNAL-LAN network
object-network 172.18.83.0 255.255.255.0
standard access list permits 172.18.83.0 SPLIT-TUNNEL 255.255.255.0
standard access list permits 172.18.80.0 SPLIT-TUNNEL 255.255.255.0
OUTSIDE_access_in list extended access permitted ip object VPNPOOL SITE-a.
Outside 1500 MTU
MTU 1500 inside
IP verify reverse path to the OUTSIDE interface
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 743.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (INSIDE, OUTSIDE) static source SITE SITE-B-B static destination VPNPOOL VPNPOOL non-proxy-arp-search to itinerary
NAT (INSIDE, OUTSIDE) static source SITE-has-a-SITE static destination VPNPOOL VPNPOOL non-proxy-arp-search to itinerary
!
object SITE-B network
dynamic NAT interface (all, OUTSIDE)
Route outside 0.0.0.0 0.0.0.0 X.X.X.X 1
Route to the INTERIOR of 172.18.80.0 255.255.255.0 172.18.83.1 1
dynamic-access-policy-registration DfltAccessPolicy
action to terminate
dynamic-access-policy-record VPNTUNNEL
AAA-server VPN-users ldap Protocol
AAA-server VPN-users (INSIDE) X.X.X.X
LDAP-base-dn DC = DOMAIN, DC = com
LDAP-scope subtree
LDAP-naming-attribute sAMAccountName
LDAP-login-password *.
LDAP-connection-dn CN = CISCO, OU = Service accounts, DC = DOMAIN, DC = com
microsoft server type
identity of the user by default-domain LOCAL
AAA authentication http LOCAL console
LOCAL AAA authentication serial console
the ssh LOCAL console AAA authentication
Enable http server
Server of http session-timeout 60
redirect http 80 outside
No snmp server location
No snmp Server contact
Telnet timeout 5
Console timeout 0
management-access INTERIOR
No ipv6-vpn-addr-assign aaa
no local ipv6-vpn-addr-assign
a basic threat threat detection
threat detection statistics
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
SSL server-version everything
client SSL version all
SSL-trust VPNCERT OUTSIDE point
WebVPN
allow outside
AnyConnect essentials
AnyConnect image disk0:/anyconnect-win-3.1.09013-k9.pkg 1
AnyConnect image disk0:/anyconnect-macosx-i386-3.1.09013-k9.pkg 2
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
VPN-tunnel-Protocol ikev1, ikev2 ssl clientless ssl ipsec l2tp client
value by default-domain domain.com
Group Policy GroupPolicy_VPN SITE internal
attributes of Group Policy GroupPolicy_VPN to SITE
WINS server no
value of 172.18.83.10 DNS server 172.18.83.11
VPN - 4 concurrent connections
VPN-idle-timeout 120
3600 VPN-session-timeout
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value of SPLIT TUNNEL
value by default-domain domain.com
WebVPN
AnyConnect mtu 1200
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect ask flawless anyconnect
attributes global-tunnel-group DefaultWEBVPNGroup
LOCAL VPN users authentication-server-group
tunnel-group VPNTUNNEL type remote access
tunnel-group VPNTUNNEL General attributes
address IP-VPN-POOL pool
LOCAL VPN users authentication-server-group
Group Policy - by default-GroupPolicy_VPNTUNNEL
management of the password password-expire-to-days 7
tunnel-group VPNTUNNEL webvpn-attributes
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the ftp
Review the ip options
inspect the pptp
inspect the tftp
inspect the icmp
class class by default
Statistical accounting of userIt is most likely your problem then. Your VPN clients, 10.240.25.0/24 can get to the Site, but because the Site doesn't know how to return to 10.240.25.0/24 traffic is lost. You will need to advertise out of site B.
-
LRT224 not getting firewall access rules do not honored
Hello
I use LRT224 with firmware version v1.0.5.03 (February 22, 2016 10:12:17). After that I had the camera that I have updated to this version, done a factor reset and started the same configuration.
I have defined four VLANS, connected my WAN link, everything is configured. Each port is assigned a VLAN which are connected to different switches. When connect us computers to each of these VLANs, we become appropriate network DHCP address and are able to surf the internet properly without any problem.
I have two or three machines in VLAN2 whereby, I want to install the virtual host configuration by using Port Forwarding.
I'm trying to map the port 8801 to port 22 on a server in the VLAN2, and so I can SSH to the server from the outside.
In the Port Forwarding, I created a new service for 8801 and using this service, I defined a redirection rule to this server in the VLAN2. I've also set trigger Port 8801 to 22. Also open the port 8801 by adding an access rule to the firewall configuration.
Despite all this, I can't access this internal server from outside.
I had a similar configuration before with a Dlink WiFi router and there it worked perfectly fine. Thus, there is no problem on the server.
I also tried Port Address Translation instead of triggering Port, still unable to connect.
When I do a port-scanning of my external IP address for port 8801, it looks like below:
For print.blrhq.public (xxx.xxx.xxx.xxx) nmap scan report
Host is (0.0031 s latency).
SERVICE OF THE PORT STATE
8801/tcp filtered unknownNot sure if the firewall is contributing to the show or the configuration of port forwarding.
In this regard, any help is appreciated.
You only need the translation rule addresses port. Remove port forwarding rule.
-
Redirect Port WRV210 not open ports
Greetings,
I have a Linksys/Cisco WRV210 Wireless-G VPN Router with RangeBooster. ISP is a dynamic IP with all ports open. I have no equipment to interact with them. they give me just a CAT5 cable on the wall. ISP-> WRV210-> LAN
Router stats
Hardware Version: WRTR-221G_V1
Software version: 2.0.0.11
Connection type: Automatic Configuration - DHCP
IP address: 10.1.222.104
Subnet mask: 255.255.255.0
Default gateway: 10.1.222.1
Port Forwarding 22152 - 22152 192.168.1.152 enabled
No trigger port
DMZ disabled
If I am controlled within the local network
nmap -p22152 192.168.1.152Interesting ports on 192.168.1.152:PORT STATE SERVICE22152/tcp open unknown
If I am controlled from outside the router (xxx and # are just my changes of masking)
nmap -p22152 desktop.dns.xxx Interesting ports on ##.###.##.###: PORT STATE SERVICE 22152/tcp closed unknown
If I am controlled from inside the LAN on the router
nmap -p22152 192.168.1.1 Interesting ports on 192.168.1.1: PORT STATE SERVICE 22152/tcp closed unknown
It seems that the router is completely ignoring my Port Forwarding instructions. I have the hard reset of the router. I've upgraded to the latest firmware. None of them has made a difference.
My final test was to see if all ports are open on the router
nmap 192.168.1.1 Interesting ports on 192.168.1.1: Not shown: 997 closed ports PORT STATE SERVICE 80/tcp open http 443/tcp open https 60443/tcp open unknown
My questikon would be if someone has a 'trick' to enable port forwarding on the road?
Thank you.
This product is managed by the Cisco Small Business Support Community.
For future discussions about this product, go here.
-
Connect a Vista PC (host) with an XP PC in LAN and share the internet connection.
I connect to internet using 3 different notebooks with Windows Vista with a wireless connection to a router and the DSL modem. I have a desktop PC XP computer in a secluded spot in my house, who does not have a wireless card. When I want to use the internet in Office XP, I connect it to a laptop using a LAN cable.
I was able to do that with 2 of my notebooks (set up the network and share the internet), but with the third Vista notebook, desktop XP can't get the internet connection established. I was not able to detect which is the problem.
First question: clues to debug this problem?
Second question: I would like to start over again and configure everything again with this third book. How should I proceed?
Turn on Internet connection sharing on the Vista wireless network connection. If asked what to use for the home network connection, tell him to use the connection to the Local network. Then check the State of TCP/IP on both computers:
- On the Vista computer, right-click on the connection to the Local network, and then click on status > details . It must show:
- IP address: 192.168.0.1
- Subnet mask: 255.255.255.0
- Default gateway: no
- Server DNS = none
- On the XP computer, right-click on the connection to the Local network, and then click on status > support > details . It must show:
- IP address: 192.168.0.x (1<>
- Subnet mask: 255.255.255.0
- Default gateway: 192.168.0.1
- = 192.168.0.1 DNS server
- On the Vista computer, right-click on the connection to the Local network, and then click on status > details . It must show:
-
I need catalog Meteric for each parameter
Hi all
I wnna a metric data catalog for each of network objects should describe each of the parameter. I want to know what all kind of setting which are in Hyperic, says for example
Hyperic HQ managed the product list > Linux Management >
FIN_WAIT State of TCP 1 TcpStateFIN_WAIT1 no FLOW fake 5 min
What does this parameter? ... use... details... etc.
Likewise I wnna know all the setting in the metrics data, so that I can set it up in my entire company for netowrok monitoring,
Hey, but I need this information as soon as it is possiable bocz, I intend to apply it in my entire company in & ant next week...
in the hope of a rapid response in the forums...
Thanks for reading.It's true Brad and we really hope that the community will be
able to help us here :)
Most of the measurements taken by the plugins is provided by the
detailed seller of the product, which often the seller provided
documentation, but not always the case. If at some point in the Middle
future, we would like to get a mechanism in place which can help the users of HQ
Find detailed descriptions of metrics.On September 11, 2006 at 06:36, Brad Felmey wrote:
> It is not reasonable to expect an immediate answer to a question
> with * thousands * of technically of detailed answers. In fact, it is not
> reasonable to think that the answer never. -
Strange error; VMware Server 2.0.1 stopped running virtual machines after update.
I was trying to understand what the problem may be, but I can't find so put my VM in your hands.
It worked perfectly until I updated my x 64 Ubuntu 8.04 to:
root@VisionServer:/usr/lib/VMware# uname - a
Linux visionserver-2.6.24 - 24-server #1 SMP Sat Aug 22 00:59:57 UTC 2009 x86_64 GNU/Linux
I also brought up the RAM from 1 GB to 8 GB, but that should not intervene, or?
The interface is not implemented service (but netstat it also lists open).
root@VisionServer:/usr/lib/VMware# netstat-l
Connections Internet active (only servers)
Proto Recv-Q Send-Q local address foreign address State
tcp 0 0 *:902 : LISTEN
tcp 0 0 *:8333 : LISTEN
TCP 0 0 localhost:8307 : LISTENING
tcp 0 0 *:8222 : LISTEN
tcp6 0 localhost:8005 0 LISTEN :*
udp 0 0 *:bootpc :
UDP 0 0 192.168.17.1:ntp :
UDP 0 0 172.16.130.1:ntp :
UDP 0 0 visionserver.vision:ntp :
UDP 0 0 localhost:ntp :
udp 0 0 *:ntp :
udp6 0 fe80::250:56ff:fec0:ntp 0 :*
udp6 0 fe80::250:56ff:fec0:ntp 0 :*
udp6 0 fe80::214:5eff:fef8:ntp 0 :*
udp6 0 0 ip6 - localhost:ntp :*
raw 0 0 *:icmp : 7
UNIX domain sockets active (only servers)
Inode proto RefCnt flags Type State path
UNIX 2 /var/run/vmware/root_0/1253661581394001_8906/ha-nfc-fd STREAM LISTENING 17007
UNIX 2 /var/run/vmware/root_0/1253661581394001_8906/ha-nfcssl-fd STREAM LISTENING 17014
UNIX 2 /var/run/vmware/proxy-Web server STREAM LISTENING 17016
UNIX 2 /var/run/vmware/root_0/1253661581394001_8906/hostd-vmdb-fd STREAM LISTENING 17065
UNIX 2 /var/run/vmware/proxy-mob STREAM LISTENING 17067
UNIX 2 /var/run/vmnat.9485 STREAM LISTEN 17901
root@VisionServer:/usr/lib/VMware# /etc/init.d/vmware-core start
Starting VMware services:
Virtual machine monitor makes
Virtual machine communication interface is
VM communication interface socket family: fact
Virtual Ethernet is
Networks bridged on/dev/vmnet0 made
Network invited only on/dev/vmnet1 (background)
Server DHCP on/dev/vmnet1 did
Network invited only on/dev/vmnet8 (background)
Server DHCP on/dev/vmnet8 is
NAT service on/dev/vmnet8 is
Demon of authentication server makes VMware (background)
Available shared memory is
Yet;
root@VisionServer:/usr/lib/VMware# /etc/init.d/vmware-core State
Networking networking on/dev/vmnet0 is running
Network host detection does not work
Invited only on/dev/vmnet1 network is running
DHCP server on/dev/vmnet1 is running
Network invited only on/dev/vmnet8 is running
DHCP server on/dev/vmnet8 is running
NAT networking on/dev/vmnet8 is running
Responsible vmmon module
Loaded module Vmnet
And no virtual machine work! ... It installs without a hitch and says that everything is good to go, but obviously not! :/
/ Thank you thousand!
Start your old kernel and see if it works.
-
fms_adminConsole.htm remote access connection time, does not connect
FlashMediaServer4.5_x64.tar.gz (fms version 4.5.1)
Linux followed instructions, success!
Information System, newspapers, etc... Below.
uname - a
Poolhdz01.localdomain 3.0.0 - 16-generic #28 - Ubuntu Linux SMP x86_64 x86_64 x86_64 GNU/Linux
lsb_release - a
Distributor ID: Ubuntu
Description: Ubuntu 11.10 x 64
News Release: 11.10
Codename: dreamlike
PS - a
PID TTY TIME CMD
1? init of 00:00:00
2? 00:00:00 kthreadd
3? ksoftirqd/0 00:00:00
6? Migration/0 00:00:00
7? migration of 00:00:00 / 1
9? ksoftirqd/1 00:00:00
10? 00:00:00 kworker/0:1
11? 00:00:00 cpuset
12? 00:00:00 khelper
13? 00:00:00 netns
15? 00:00:00 sync_supers
16? BDI-default of 00:00:00
17? 00:00:00 kintegrityd
18? 00:00:00 kblockd
19? 00:00:00 ata_sff
20? 00:00:00 khubd
21? 00:00:00 md
22? 00:00:00 khungtaskd
23? 00:00:00 kswapd0
24? 00:00:00 ksmd
25? 00:00:00 khugepaged
26? 00:00:00 fsnotify_mark
27? 00:00:00 ecryptfs-kthrea
28? Crypto of 00:00:00
36? 00:00:00 kthrotld
39? 00:00:00 scsi_eh_0
40? 00:00:00 scsi_eh_1
41? 00:00:00 kworker / u: 2
61? 00:00:00 kworker/0:2
189? 00:00:00 scsi_eh_2
196? 00:00:00 scsi_eh_3
216? 00:00:00 scsi_eh_4
217? 00:00:00 scsi_eh_5
218? 00:00:00 scsi_eh_6
219? 00:00:00 scsi_eh_7
220? 00:00:00 scsi_eh_8
221? 00:00:00 scsi_eh_9
225? 00:00:00 kworker / u: 7
243? 00:00:00 kjournald
295? 00:00:00 upstart-udev-br
304? 00:00:00 udevd
339? 00:00:00 16/irq-mei
393? 00:00:00 udevd
394? 00:00:00 udevd
452? 00:00:00 kpsmoused
551? upstart of 00:00:00 - socket-
570? 00:00:00 kjournald
578? 00:00:00 kjournald
602? 00:00:00 sshd
603? 00:00:00 rsyslogd(8)
613? 00:00:00 dbus-daemon
658 tty4 00:00:00 getty
00:00:00 tty5 664 getty
668 tty2 00:00:00 getty
00:00:00 670 tty3 getty
00:00:00 676 tty6 getty
687? 00:00:00 irqbalance
697? 00:00:01 mysqld
705? 00:00:00 named
709? cron to 00:00:00
712? 00:00:00 atd
775 getty tty1 00:00:00
839? 00:00:00 console-kit-dae
906? 00:00:00 polkitd
1052? 00:00:00 sshd
1071 pts/1 00:00:00 bash
1303? 01:00:00 fmsmaster
1324? httpd to 00:00:00
1325? httpd to 00:00:00
1326? httpd to 00:00:00
1327? httpd to 00:00:00
1410? 04:00:00 fmsedge
1489? 00:00:03 kworker/1:2
1506? 00:00:01 fmsadmin
1555? httpd to 00:00:00
1583? 09:00:00 fmscore
1736? 00:00:00 hunting-8:0
1766? 00:00:00 kworker/1:1
1775 pts/1 00:00:00 ps
netstat - listen
Connections Internet active (only servers)
Proto Recv-Q Send-Q local address foreign address State
TCP 0 0 *: 1935 *: * LISTEN
tcp 0 0 *:www *:* LISTEN
TCP 0 0 *: 2224 *: * LISTEN
TCP 0 0 19.103 - 44 - 209.st:domain *: * LISTEN
TCP 0 0 poolhdz01.locald:domain *: * LISTEN
TCP 0 0 poolhdz01.localdo:19350 *: * LISTEN
TCP 0 0 *: 1111 *: * LISTEN
TCP 0 0 poolhdz01.localdoma:953 *: * LISTEN
TCP 0 0 poolhdz01.localdo:11110 *: * LISTEN
TCP 0 0 *: 8134 *: * LISTEN
TCP 0 0 poolhdz01.localdo:mysql *: * LISTEN
tcp6 0 0 [:]: 2224 [:] LOOK :*
tcp6 0 0 [:]: domain [:] LOOK :*
tcp6 0 0 ip6 - localhost:953 [:] LOOK :*
/ etc/hosts
127.0.0.1 localhost poolhdz01.localdomain
127.0.1.1 netelubuntuinstall.localdomain netelubuntuinstall
/ etc/hostname
poolhdz01.localdomain
/opt/Adobe/FMS/logs/master.00.log
#Version: 1.0
#Start - date: 2012-03-01 19:29:49
#Software: adobe Flash Media Server 4.5.1 r484 x 64
#Date: 2012-03-01
#Fields: date time x - pid registered x x - ctx x-comment
2012-03-01 19:29:44 1303 (i) FMS detected IPv6 proto 2581173
col stack! -
2012-03-01 19:29:44 1303 (i) 2581173 FMS config < NetworkingI
Activate IPv6 = false > -.
2012-03-01 19:29:44 1303 (i) FMS in IPv4 pro 2581173
Slim stacking mode! -
2012-03-01 19:29:44 1303 (i) 2581173 host: poolhdz01.localdo
Primary IPv4: 209.44.103.19 -.
2012-03-01 19:29:44 1303 (i) 2571011 Server from... -
2012-03-01 19:29:46 1303 (i) 2581413/opt/adobe/fms/Apache2.
2/bin/httpd - f./conf/httpd.conf d' / opt/adobe/fms/Apache2.2 'k start returne.
0 d: [Thu Mar 01 19:29:44 2012] [info] mod_jithttp - FMS installation path: / o «»
"PT/adobe/fms / -.
2012-03-01 19:29:46 1303 (i) 2581224 ar Edge started, (1410)
guments:-edgeports ": 1935" - coreports "localhost:19350" - conf "/ opt/adobe/fms.
/ conf/Server.xml "-adaptor"_defaultRoot_"- the name"_defaultRoot__edge1"- edgenam".
e 'DA1 '. -
2012-03-01 19:29:46 1303 (i) 2571111 server started (/ opt/ad)
obe/fms/conf/Server.xml). -
2012-03-01 19:31:07 1303 (i) started 2581221 Core (1583), ar
guments: - adaptor "_defaultRoot_", "_defaultVHost_" - vhost - app - inst-tag "_".
1 "- console - conf" / opt/adobe/fms/conf/Server.xml "-name"_defaultRoot_:_defau "
ltVHost_:_1 ". -
/opt/Adobe/FMS/logs/edge.00.log
#Version: 1.0
#Start - date: 2012-03-01 19:29:51
#Software: adobe Flash Media Server 4.5.1 r484 x 64
#Date: 2012-03-01
#Fields: date time x - pid registered x x - ctx x-comment
2012-03-01 19:29:46 1410 (i) FMS detected IPv6 proto 2581173
col stack! -
2012-03-01 19:29:46 1410 (i) 2581173 FMS config < NetworkingI
Activate IPv6 = false > -.
2012-03-01 19:29:46 1410 (i) FMS in IPv4 pro 2581173
Slim stacking mode! -
2012-03-01 19:29:46 1410 (i) 2581173 host: poolhdz01.localdo
Primary IPv4: 209.44.103.19 -.
2012-03-01 19:29:46 1410 (i) 2631174 listener started (_def
aultRoot__edge1): localhost:19350 / v4-
2012-03-01 19:29:47 am 1410 (i) 2631174 listener started (_def
aultRoot__edge1): 1935/v4-
2012-03-01 19:29:48 1410 (i) 2631174 listener started (_def
aultRoot__edge1): 127.0.0.1:19350 (rtmfp-core) / v4-
2012-03-01 19:29:48 1410 (i) 2631174 listener started (_def
aultRoot__edge1): 209.44.103.19:19350 (rtmfp-core) / v4-
2012-03-01 19:29:48 1410 (i) 2631509 Public rtmfp-core addre
small businesses for listener _defaultRoot__edge1 are: 127.0.0.1:19350; 209.44.103.19:19350.
2012-03-01 19:29:48 1410 (i) 2631174 listener started (_def
aultRoot__edge1): 127.0.0.1:1935 (rtmfp) / v4-
2012-03-01 19:29:48 1410 (i) 2631174 listener started (_def
aultRoot__edge1): 209.44.103.19:1935 (rtmfp) / v4-
2012-03-01 19:31:07 1410 (i) 2581252 registration core (1583)
/opt/Adobe/FMS/conf/FMS.ini
SERVER. ADMIN_USERNAME = zach
SERVER. ADMINSERVER_HOSTPORT =: 1111
SERVER. PROCESS_UID = 1001
SERVER. PROCESS_GID = 1001
SERVER. LICENSEINFO =
LIVE_DIR = / opt/adobe/fms/applications/live
VOD_COMMON_DIR = / opt/adobe/fms/webroot/vod
VOD_DIR = / opt/adobe/fms/applications/vod/media
SERVER. FLVCACHE_MAXSIZE = 500
SERVER. HTTPD_ENABLED = true
ADAPTER. HOSTPORT =: 1935
HTTPPROXY. HOST =: 8134
ADAPTER. HTTPIDENT2 =
VHOST. APPSDIR = / opt/adobe/fms/applications
APP. JS_SCRIPTLIBPATH = / opt/adobe/fms/scriptlib
RECORDER. LOGDIR =
"USE." HTTPCOMMAND_ALLOW = true
/opt/adoble/FMS/conf/users.XML
< root >
< UserList >
< username = ' ${SERVER.» ADMIN_USERNAME} ">"
No. displayed < password > < / password >
allow <>< / allow >
< deny > < / nie >
< order > allow, deny < / order >
< / user >
< / UserList >
< AdminServer >
< HTTPCommands >
< activated >$ {USERS. HTTPCOMMAND_ALLOW} < / activate >
Ping < Allow > < / allow >
< deny > all < / deny >
< order > deny, allow < / order >
< / HTTPCommands >
< / AdminServer >
< / root >
FMS 4.5.1 is available here http://209.44.103.19/
Maybe this information we'll see why http:80 connection will not accept my credentials.
Thanks in advance.
I solved my problem... The default admin port: 1111 wasn't redirected when using NAT and instead use nmap to route open ports and 2222 was available. Generally used for ssh terminal administration...
Edit /opt/adobe/fms/conf/fms.ini and change:
Of the SERVER. ADMINSERVER_HOSTPORT =: 1111
To the SERVER. ADMINSERVER_HOSTPORT =: 2222 or port is bidirectional via tcp
I suggest Adobe to set the SERVER. ADMINSERVER_HOSTPORT =: 2222 default to aleviate this common problem.
-
Wandering SQL Native Client Datasource - apparently, it's a pretty common problem and I see several resolutions to it. This problem started for our long company until I started working here. We do not allow remote connections. JDE Enterprise Server and SQL server are on the same subnet. Users are on a different subnet. SQL Server gets this message tries to connect to the Server Enterprise JDE:
Connection failed: State 08001 ' SQL': SQL Server Error 10061: Microsoft SQL Native Client TCP provider: no connection could be made because the target machine actively refused it.
I tried several suggested solutions and do not get the case. Any help is appreciated. Thank you, Sophie
Hello
The issue of Windows XP, you have posted is better suited for the IT Pro TechNet public. Please ask your question in the SQL Serversupport for assistance.
Hope the helps of information.
Concerning
Joel S
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think. -
"sh conn" State tcp - connection problem.
Hello
I see the problems of random hosts connection that runs through the inside of my PIX535 (point 6.1.1) through a global IP address, to a couple of specific servers on the internet.
When the problem accurs machines Pat ' ted behind the World Cup have an IP connectivity for web servers mentioned, but not tcp/80
Staticly NAT'ted machines are not affected by the problem.
I can see (with "sh conn [Web server-IP]" ' and ' sh xlate ") that the workstations are PAT'ted correctly to a global port and a connection attempt is made:
y.y.y.y = IP of the workstation
x.x.x.x = my global IP
z.z.z.z = the foreign Web server
f edb1-1 # sh local xlate [y.y.y.y]
Global PAT [x.x.x.x] (16412) Local y.y.y.y (1959)
f edb1-1 #sh conn foreign z.z.z.z
TCP on z.z.z.z:80 in y.y.y.y:1959 idle 0:00:45 0 flags saA bytes
What I don't know, what exactly does the flags 'saA '? I found more on cisco.com:
s waiting outside SYN
a ACK outside waiting for SYN
A waiting inside the acknowledgement to SYN
two aA are logical for me: Firewall has not yet received an ACK packet from the Web server.
However, I'm not shure on what to conclude on the "s". What 'pending outside SYN' actually mean? My firewall passed jobs package SYN at this point?
Thanks in advance,
--
Lasse Björn Jensen
Standard TCP protocol requires that the receiver respond to an initial SYN packet with a SYN ACK. The ASA flags indicate that we have seen a SYN from a customer inside and are waiting for the SYN ACK (sa) from the outside host and then the ACK (A) inside the host in response to the SYN ACK. Looks like the target machine does not meet the customers using the PAT address. Need us more information to determine the cause. I hope this helps.
Scott
-
Cisco VPN client stats - bypassed packages
I have a profile that does not allow for split tunneling for the VPN client. Yet, when a client connects, the connection statistics indicate that some traffic is listed as 'bypassed '.
Did someone knows what this traffic would be, and it is indeed without going through the tunnel and go to the directly connected LAN?
Thanks in advance.
Hello,.
Here's an explantion:
Bypassed packages - the total number of packets of data that the Client VPN do not apply because they must not be encrypted. Local ARPs and DHCP are in this category.
If you happen to have a screenshot of packages more closely examine these packages?
I hope this helps! If Yes, please rate.
Thank you
-
My child allows to bypass the parental control
My child to bypass the parental control on his Macbook Air using the method presented in this video tutorial. Is there a way to avoid this? https://www.YouTube.com/watch?v=Br6wKR28jFo
With the text of the video section, the way used by the author to exploit the single user Mode
command line is specified; and it has been done before. Don't know if there are more recent methods
to try to deter the child since the creation of their own Admin account to bypass the controls that
those already discussed adjacent older sons, like this:
How to stop a person setting up an administrative account duplicate (hackmac)?
Although it is possible to learn how and use the Open Firmware password, to attempt to get the Admin acct
This could also be overcome by a particular person looking to exploit a work around physical access.
In the past, some computer models were easier to open and to perform tasks that could derail this method.
Almost any iFixit or removable guide could be useful for a particular child or student, as a work-around.
See suggestions on how to apply the Firmware password, as well as the means to
block access to the material or the way to reset the admin by OS X Recovery password, in news
OS X versions that use this partition and its utilities. It is part of the problem with the Admin
operation, the user is physical access to the computer. And why remotely hacking is very difficult.
• Use a password of the firmware on your Mac - Apple Support
While I have no other suggestion (knowing that there could be a fairly simple method to work around the)
and most have been published online for several years) I hope that someone will see & respond to your
question with any method you can implement. Or see if an Apple Store genius bar can help you
This question, because it creates problems. I'd be sure to make an appointment to discuss this at the store.
If no official Apple retail Store is available, you should perhaps consider a call to Apple support or use a
online chat. Don't forget to mention details about the build year computer, etc. & the version OS X in it.
You can choose to make submissions directly to Apple's comments on this issue, if you find that it is not effective
method of maintenance determined children or young adults to change their own Admin computer.
One of the comments below links is probably more suited to this topic than the other:
Contact Apple support
http://www.Apple.com/contact/
Need service or support? Start your online application and we will find a solution.
More ways to get help:
- Contact iTunes Store support
- U.S. iPod, Mac and iPad technical support: (800) APL - care (800-275-2273)
- Technical support for iPhone in the United States: (800) MY-IPHONE (800-694-7466)
- See all phone numbers around the world
Since there is no response when I first noticed your thread, I asked guests move it more appropriate
location for visibility in these discussions of support; so they chose to put it in the section of MacBook Air.
Good luck in this case!
-
Hello!
Now check the status of TCP socket in wait times.
TCP is a connection Windows server and controller for cRIO with LabVIEW applications.
I don't know everything made on the State of demand in my cRIO I decide for information on physical connection timeout of entry level and application level - reading Timeout (if I can't send something - ethernet is not bound or socket is dead; if I did packets sent and get timeout response read only (: my application the cRIO died).
But when I disconnect ethernet - I do not write timeout error regardless of the value of timeout, I don't get any errors on the writing at all. I'm reading wait times only (because my system gets all the packages to answer) and then, after some time, error 66 on writing (I think - when my disconnection on its side and is TCP cRIO now the listening TCP by his own time-outs device).
Why it's happening?
Are there other tools to get the status of the socket (at least to his physical level only)?
WBR,
Igor
Hello Igor.
Unfortunately, the timeout for TCP to write command does not work as most people expect. This discussion forum:
Crosses, why this is and what the timeout command is actually configuration as well as different ways to circumvent this.
Thank you!
-
Close TCP leaves the connection open
Hello guys,.
I use an ethernet connection to query the data of 2 units of acquisition of sensors.
This request is motivated by a second timed loop period 30. As this rate is very low, I have the close connection and reopen it each time.
I try to connect to the device via the same 2 ports each time, 50,000 and 50 001.
I get the error message that the connection is already used for a close connection of TCP executed without error before.
The network view TCP tool monitor gives me the screen following [network_connections.png] when I run w/o specifying the local port. It seems that the previous connection are not adequately closed and are always in the TIME_WAIT state. This list is continuouslly prices, leading to errors of networks. (For the units IP address is 200.0.4.152 and 153)
Could you please help me on this?
Thanks in advance
Kind regards
Bruno
Hello
This seems to be a common behavior:
http://digital.NI.com/public.nsf/allkb/119D334B8B78732E862574E1006D1839
Maybe you are looking for
-
Hey I lost my ios for my macbook how to fix
Hey I lost my ios for my macbook how to fix or install ios
-
My iPad just given of the pop up asking to change my password for 60 seconds. Is - this malware?
I received a request to change my password in 60 seconds. What concerns me, it could be malware and off the iPad. Someone had this problem?
-
Need drivers for Windows 7 for my Satellite C55D - A - 13 G
Hello I can't find drivers for my laptop to Windows 7. Links on the page to Toshiba does not. Help, please.
-
Try to adapt the XY graph output
Hello, I'm trying to adapt to the output of a XY Chart which is (table 1 d of Cluster of 2 elements (2 x 1 - D doubles [64-bit real])). It seems that instead of having a table with two columns X, Y indexed number of persample, I want to have a table
-
Card driver Wifi HP Pavilion 15-n002sk moved (8.1 to Windows 64 - bit)
Hello world I've already installed Windows 8.1 64 bit on my laptop and the card Wifi is not already installed. I tried to download the Wifi card driver and I found 3 drivers: MediaTek (Ralink) 802.11 (WLAN) wireless LAN adapter http://h10025.www1.HP.