Suggestions of VPN for Windows 7 and ASA 5510

Similar Questions

• Remote IPSec VPN - client Windows 7 and ASA 5505

  Hello

  I'm having trouble with configuring IPSec VPN with Cisco ASA 5505 and Windows 7 client native VPN remotely. My client PC Gets the VPN IP pool address and can access a remote network behind ASA, but then I lose my internet connection. I read that this should be a problem with the split tunneling, but I did as it says here and no luck.

  Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have an internet connection (given that the customer is using a local gateway), but then I can't ping remote network.

  In the log, I see the warnings of this type:

  TCP connection of disassembly 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0: 00:00 0 stream bytes is a loopback (cisco)

  I have attached my configuration file (without configuring split tunneling, I tried). If you need additional newspapers, I'll send them right away.

  Thank you for your help.

  Petar Koraca

  That's what you would have needed on versions 8.3 and earlier versions:

  permit same-security-traffic intra-interface

  Global 1 interface (outside)

  NAT (outside) 1 192.168.150.0 255.255.255.0

  However I see that you are running 8.4 so I think that all you need is this (I never did on 8.4 so it may not be accurate)

  permit same-security-traffic intra-interface

  network of the NETWORK_OBJ_192.168.150.0_24 object

  dynamic NAT interface (outdoors, outdoor)

  Give it a shot and let me know how it goes.

• ASA 5505 and ASA 5510 Site to Site VPN Tunnel cannot be established

  Hi all experts

  We are now plan to form an IPSec VPN tunnel from site to site between ASA 5505 (ASA Version 8.4) and ASA 5510 (ASA Version 8.0) but failed, would you please show me how to establish? A reference guide?

  I got error syslog 713902 and 713903, how to fix?

  I got the following, when I type "sh crypto isakmp his."

  Type: user role: initiator

  Generate a new key: no State: MM_WAIT_MSG2

  Hugo

  Hello

  This State is reached when the policies of the phase 1 do not correspond to the two ends.

  Please confirm that you have the same settings of phase 1 on both sides with the following commands:

  See the isakmp crypto race

  See the race ikev1 crypto

  Also make sure that port UDP 500 and 4500 are open for communication between your device and the remote peer.

  Finally, make sure you have a route suitable for the remote VPN endpoint device.

  Hope that helps.

  Kind regards

  Dinesh Moudgil

• I bought 2 Adera for Windows 8, and it will not download. Whenever I click on the download icon, nothing happens.

  I bought 2 Adera for Windows 8, and it will not download. Whenever I click on the download icon, nothing happens. It becomes extremely frustrating that the account has been debited from my bank immediately... Still no game! Any suggestions please. Thank you

  Hello

  You must get in touch with the sales of Microsoft and Windows Store Support for help on this issue.

  To avoid such problems in the future, you can try to reset the Windows Store cache, and then try to buy apps.

  Reset the Windows Store Cache steps.

  a. press Windows + R on your keyboard to open the Run dialog box.

  b. type WSReset.exe, and then click/click on OK.

  c. the information store now open and indicate the following: for the store cache has been cleared.

  Please let us know in case you need assistance on issues related to Windows.

• Pavilion a6530f: what video card installed works for Windows 10 and a 300W power supply?

  I have a6530f a desktop Pavilion PC.  I am currently running Windows 7 and am interested in upgrading to Windows 10.  I get and error message when you try to install the W10.  "NVIDIA GeForce 6150SE nForce 430".  I think I need to improve my video card.  Can what video card I install that will work for Windows 10 and is rated for the power supply 300W in my lap?  I'm not very techie.

  Many of these inexpensive graphics cards for Newegg.com should work with Windows 10. Just watch for those who require a 300 watt power supply system or less.

  Drivers for these cards may be on the page drivers GeForcefunds. Simply select the card in the drop-down list or use the "Auto-Detect".

  If you have any other questions, feel free to ask.

  Please click the White Star of KUDOS to show your appreciation

• HP envy 14-2090eo: can I use the same drivers for windows 8 and 8.1

  When I check in drivers which operating systems there are drivers available for my Hp Envy 14-2090eo, it says Windows 8 (64-bit) and Windows 7 (64-bit), "and im currently using Windows 7 64 bit" but does that mean the drivers to support these 2 Windows 8 and 8.1 of Windows operating systems, said in a different way "» : are the same drivers for Windows 8 and Windows 8.1?

  Best regards from hpenvy1

  Hello:

  Your model has the AMD/Intel switchable graphics.

  It is unlikely that the W8 AMD graphics driver will work on W8.1.

  Normally, you can use some of the drivers W7/W8 on W8.1, but the graphics is very doubtful - not switchable graphics anyway.

  You can run the windows 8.1 upgrade wizard and see what it reports.

  http://Windows.Microsoft.com/en-us/Windows-8/Upgrade-Assistant-download-online-FAQ

• Cannot download the update from microsoft > update security for windows media encoding for windows xp and windows server 2003 kb2447961

  I am running HP pavillion A1130n desktop computer > problem > I can not IN stall Microsoft Update > update security for windows media 9 for windows xp and windows server 2003 kb2447961 of coding... .e send me a response message. > * E-mail address is removed from the privacy *.

  Hello
  
  1. don't you encounter any error message during the installation of this update?
  2 is this problem limited to this particular update?
   
  I ask to download the update manually and then install it.
  Here is the download link:
  A security update for Windows Media Encoder 9 Series for Windows XP and Windows Server 2003 (KB2447961)
  http://www.microsoft.com/downloads/en/details.aspx?familyid=EF0ADA2C-965F-438F-A1D3-BD45DB8460C1&displaylang=en.
   
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I'm trying to install updates for computer that are recommended, but they are for Windows Vista and I'm now running Windows 7 and receive errors. How can I fix it?

  I'm trying to install updates for computer that are recommended, but they are for Windows Vista and I'm now running Windows 7 and receive errors. How can I fix it?

  Hi Barcini,

  ·        This error message do you receive when you try to install updates?

  ·        What updates are you inviting to install?

  You can run the Windows Update Troubleshooter & check if the problem persists.

  Open the Windows Update troubleshooting tool

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I installed a game for windows XP and then used the troubleshooting tool to convert so that I can play in 7.__it still doesn't react. What should I do? Please answer__

  I installed a game for windows XP and then used the troubleshooting tool to convert so that I can play at 7.
  It still fails. What should I do? Please answer

  Hello

  a. what game do you have installed?
  b. do you get errors trying to run the game in compatibility mode?

  Look for error messages in the event viewer. If you find error messages after return the exact error message so that we can help you better.

  Measures to check the application event log:

  1. click on start.
  2. in the search box type eventvwr.msc, and then on enter.
  3. now, click Application in the event viewer (local).
  4. now locate the event log on the right side of the event viewer window.

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer 
  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  You can try to perform the clean boot on your computer and check if that helps.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  To perform a clean boot on a computer, follow these steps.
  1. click on start, type msconfig in the search box and press ENTER.

  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.

  2. in the general tab, click Selective startup.
  3. under Selective startup, clear the check box load startup items.
  4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.
  5. click on OK.
  6. When you are prompted, click on restart.
  7. after the computer starts, check if the problem is resolved.

  Please follow the system in the boot environment. If the problem does not occur, it indicates that the problem is related to an application or a service, we have disabled. You can use the MSCONFIG tool again to reactivate the disabled one by one element to find the culprit.

  If your issue is resolved, follow the how to determine what is causing the problem section in KB article to narrow down the exact source.
  For more information visit: http://support.microsoft.com/kb/331796

  After you determine the startup item or the service that is causing the problem, contact the manufacturer of the program to determine if the problem can be solved. Or, run the System Configuration utility, and then click to clear the check box of the element of the problem.

  To restore your computer to a Normal startup mode, follow these steps:

  1. click on start in the box start the search.
  2. type msconfig and press ENTER.

  If you are prompted for an administrator password or a confirmation, type the password, or provide confirmation.

  3. on the general tab, click Normal Startup - load all device drivers and services and then click OK.
  4. When prompted, click on restart.

  You can check its compatibility with windows 7 in the Compatibility Center.
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  Hope this information is useful.

• Windows PowerShell 2.0 and WinRM 2.0 for Windows XP and Windows Embedded (KB968930)

  Windows PowerShell 2.0 and WinRM 2.0 for Windows XP and Windows Embedded (KB968930)

  Hello

  ·         What exactly is the problem you are facing with this update?

  ·         You are able to install this update?

  If you encounter a problem installing this update you can try to install manually from the link and check if it helps:

  http://www.Microsoft.com/download/en/details.aspx?ID=16818

• Try to install Service Pack 2 for Windows Vista and it says this "one or more system components that require the service pack are missing" need help?

  Try to install Service Pack 2 for Windows Vista and it says this "one or more system components that require the service pack are missing" need help?

  Hi, Mksethompson,

  What is your model of computer?

  Error message when you try to install Windows Vista Service Pack 2: "one or more system components that require the service pack are missing."

  http://support.Microsoft.com/kb/968279

  Dell issue

  http://en.community.Dell.com/support-forums/software-OS/f/3524/t/19278096.aspx

• I try to use windows excel for windows vista and am asked for a product key. How can I find out what order to use the product?

  I try to use windows excel for windows vista and asks me to enter a product key. I am the sole owner of the computer but have no installation CD for recharge Excel. How can I find out what order to use the product? From now the product doesn't let me do anything. Help, please!

  Hello

  Did you pay for Office (including Excel) in a packaging separated when you bought your computer?

  Office is not included with your purchase of computer for free.

  Most new computers come with a trial version of Office that lets 'x' number of days usuage.

  After this test times out, you will have to buy Office.

  And the product key on the computer case or laptop for the operating system, not for the desktop Suite.

  Here is the link for the Microsoft Store to Office products:

  http://www.microsoftstore.com/store/msstore/HTML/pbPage.Office_Category_Page?ICID=Home_4up_1_OfficeCatPage

  And you might be interested in the free Open Office Suite of Office Applications.

  http://www.OpenOffice.org/

  For any other question about Office, please repost in the Office Forums:

  http://answers.Microsoft.com/en-us/Office

  See you soon.

• I have an OEM of Windows Vista version on a dying computer. Can I buy the upgrade for Windows 8 and install it on the new PC, I'm building?

  I have an OEM of Windows Vista version on a dying computer. Can I buy the upgrade for Windows 8 and install it on the new PC, I'm building? The upgrade, is published at the same time as I'm rebuilding my PC. I'm just looking to replace my OS. I need Vista.

  Hello

  OEM license is tied to the first machine that is installed on the OEM license dies when this machine dies.

  An OEM license is not transferable.

  And you need a legal edition of Windows, enabled for upgrade.

  There is no use, you buy a license upgrade of Windows 8 by itself as you have to upgrade anything of in the new computer, you build...

  You can buy a license of Windows 8 when it comes out later this year.

  See you soon.

• HP Pavilion n072sy-15 Notebook PC - where to find all the drivers for Windows XP and Windows 7

  Who knows where to find all the drivers for Windows XP and Windows 7 for HP Pavilion n072sy-15 Notebook PC?

  Hello:

  XP will not install or run on a PC with an Intel 8 series chipset, so you need not be concerned with finding drivers.

  Here is the link to a template that you can use the W7 x 64 bit drivers from.

  When you install the graphics drivers, first install the Intel HD graphics driver, reboot and then install the graphics driver nVidia.

  DO NOT USE ALL DOWNLOADS OF BIOS OR FIRMWARE FROM THIS LINK

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=6521374

• Update for Windows Vista and receive error 80070490 & 643 codes; any ideas?

  Update for Windows Vista and receive error 80070490 & 643 codes; any ideas?

  80070490 = permission denied / [a problem initializing or using session variables] or item not found

  80070643 = ERROR_INSTALL_FAILURE

  http://support.Microsoft.com/kb/958044