Support USB 2.0 missing HP Compaq dc7600 Convertible Minitowers

Similar Questions

• With my HP Compaq DC7800 Convertible Minitowers audio driver problem

  Hello

  I'm having a problem of sound driver with my desktop HP Compaq DC7800 Convertible Minitowers.

  A few days ago I formatted my desktop PC and installed a new Windows XP Service pack 3. Like I need driver for my device, I managed to find all the drivers except for my audio device. As I saw that I have integrated audio on my motherboard, but the drivers I found on a HP support site (download the drivers), none of them work and there are too many (I also need to download drivers for other devices form intel site but that's another question). So, now I was hoping someone can help me find (finally) and install peripheral audio, so I can finish with the installation process. I will be grateful for this veeeeeerrrry thanks in advance.

  It does not matter. I found the driver that I needed: ADI high definition (HD Audio Driver - Sound Max)

  thx anyway

• HP Compaq dc7800 Convertible Minitowers

  Hello

  New to the forum please bare with me I have a

  HP Compaq dc7800 Convertible Minitowers (CZC7413306) and want to update the graphics card without much expense I have short listed two cards. NVIDIA GT 630 and the GT640 Nvidia.

  One of these can receive free updates on the PC, IE PSUS?

  There 4gig of RAM onboard and at present a 7600gs Nvidia who struggles with FSX and can't not watch run them more than I I'd like to run two monitors.

  Thanks for any answers

  Concerning

  Stewart

  Thanks for the graphics card. It seems that they should work, but I still think there may be a problem with the amouint of the power supplied to the card in the slot of the ISDR - x 16.

  It would still be useful to measure the power supply to see if an upgrade PSU will fit. An upgrade to a 450W Corsair or OCZ PSU will be not much ofexpense. When you consider what you have in the PC at this time is minimal, that would make it useful. In any case, these are my thoughts on this subject.   , Of course, it's your choice.

• HP Compaq dc7700p: how to fix '1801 Microcode Update error' HP Compaq dc7700p Convertible Minitowers

  Hello

  I read and read this post for a few times and I'm not sure it will work on my PC so I have to ask, how to solve '1801 Microcode Update error' in HP Compaq dc7700p Convertible Minitowers I upgraded it with E7200 instead of the original E6300

  Here is the product number: p/n RN120ET #UUZ

  I am in a position to start and start windows, I don't know is that it works normally or not, I'm just bored with the startup message:

  Please HELP and thank you in advance!

  Hello:

  You must upgrade the BIOS to version to get rid of the error of microcode, and processor at half the speed of the FSB only works because the update of the BIOS was not written for the E7xxx processors work correctly.

  You will need to run this software whenever you enter windows and change the multiplier up.

  Or you can run this batch file listed on the bottom of Web page so that it runs automatically.

  http://CrystalMark.info/software/CrystalCPUID/index-e.html

  If I were you, I just install an E6700 Conroe and have an update without problem.

  You will need to use the BACK base flash because I don't think that there is an update of the BIOS written for W7.

• HP Compaq DC7800 Convertible Minitowers - hard drive upgrade

  I have a HP Compaq DC7800 Convertible Minitowers XP Professional running.  The vehicle currently has a 80 GB hard drive.  I want to switch the hard disk.  How can I find out what Western Digital 1 TB hard drive will work?  I asked WD, and they said that I needed to contact HP.

  Hello:

  You may have a problem upgrading to a SATA III.

  Please see what lower thread and my personal experience, installing a WD SATA III HARD drive in my dc7800.

  http://h30434.www3.HP.com/T5/TouchSmart-PC/TouchSmart-610-1030f-hard-drive-replacement/m-p/2952801/highlight/true#M21430

• Find the Audio driver for HP dc7600 convertible minitowers PC for Win7

  Dear all Member,

  I have two HP dc 7600 and computer in minitour convertible HP dc 7800 PCs, recently I upgraded the old OS win XP of them for the new OS Win 7, I'm looking for drivers for Win7 in here, but until now, I couldn't find the Audio driver for Win 7.

  Some audio that I found them on the web for HP to be compatible with Win7 drivers, but they are unsupported when I installed them on my computer.

  You help me by sending the right link to download the Audio drivers for Win7 on HP dc7600, dc7800?

  Thank you very much.

  Chinh_Ng.

  Hello:

  For the dc7600, the best thing to do is to go to the realtek website and download and install the latest driver for the audio.

  Accept the agreement. Download and install the driver either the 1st or the 2nd on the list depending on whether you have installed W7 32-bit or 64-bit.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1 & PNid = 24 & PFid = 24 & Level = 4 & Conn = 3 & DownTypeID = 3 & getdown = false

  I have a dc7800 CMT and I used the audio driver from the support page and driver and it worked perfectly for me, so I can't help you there.

  I used the one on the link below.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & cc = us & prodTypeId = 12454 & prodSeriesId = 3459240 & prodNameId = 3459243 & swEnvOID = 4059 & swLang = 13 & mode = 2 & taskId = 135 & swItem = vc-75954-1

• How to solve '1801 Microcode Update error' in HP Compaq dc7800 Convertible Minitowers

  I have Intel Core 2 Duo 2.93 GHz. My operating system is Windows 7 Ultimate x 64.

  Hello:

  The E7500 processor is not supported in the dc7800, reason why you get the error of microcode.

  Here is the list of supported processors.

  Intel Core 2 Duo processors:

  Processor Intel Core 2 Duo E4500 (2.20 GHz, 2 MB L2 cache, 800 MHz FSB)

  Processor Intel Core 2 Duo E4600 (2.40 GHz, 2 MB L2 cache, 800 MHz FSB)

  Processor Intel Core 2 Duo E4700 (2.6 GHz, 2 MB L2 cache, 800 MHz FSB)

  Processor Intel Core 2 Duo E6550 (2.33 GHz, 4 MB L2 cache, 1333 MHz FSB)

  Processor Intel Core 2 Duo E6750 (2.66 GHz, 4 MB L2 cache, 1333 MHz FSB)

  Processor Intel Core 2 Duo E6850 (3.0 GHz, 4 MB L2 cache, 1333 MHz FSB)

  Processor Intel Core 2 Duo E7200 (2.53 GHz, 3 MB cache L2, FSB to 1066 MHz)

  Processor Intel Core 2 Duo E7300 (2.66 GHz, 1066 MHz FSB, L2 cache 3 MB)

  Processor Intel Core 2 Duo E8200 (2.66 GHz, 6 MB L2 cache, 1333 MHz FSB)

  Processor Intel Core 2 Duo E8300 (2.83 GHz, 6 MB L2 cache, 1333 MHz FSB)

  Processor Intel Core 2 Duo E8400 (3.00 GHz, 6 MB L2 cache, 1333 MHz FSB)

  Processor Intel Core 2 Duo E8500 (3.16 GHz, 6 MB L2 cache, 1333 MHz FSB)

  Inter Processor Core 2 Duo E8600 (3.33 GHz, 6 MB L2 Cache, bus front end to 1 333 MHz)

  As a long shot, you can try to install the latest firmware update. You must use a bootable USB key with back files in order to run the flashbin.exe command after copying the microcode update files in your USB drive bootable.

  I can't support dc7800 site. When you can, choose the 2010 v1.14 firmware update download

  If you are unfamiliar with how to make a bootable flash drive, this is a good 'how' of the article with the files you need.

  http://www.techpowerup.com/forums/showthread.php?t=47812

  Paul

• OS for HP Compaq dc7800p Convertible Minitowers boards

  Gentlemen (and the occasional Lady).

  I just bought a minitour Convertible HP Compaq dc7800p computer on the cheap.

  From what I see, it seems almost not modified from its original configuration. It has an Intel Core Duo E6550 2.33 GHz processor, 2 GB of DDR2 RAM, a 80 gig HARD drive and DVD read/write.

  HARD drive appears to have already disappeared completely - not even a left system recovery partition - so, no OS.

  I ran HP Insight Diagnostics on it and everything passed the comprehensive test.

  Now that I am fairly confident that it will work properly, I need to choose an operating system. It comes with Vista Business and I can get a replacement from HP for $11.00 drive. I don't know what service packs, where applicable, the hot spare. This would be a factor because I am limited to 56 k modem and these service packs would take a loooong time to download. But, all things being equal, I'd rather have Windows 7 Premium. The problem is that all things are not equal! A copy of Windows 7 is around $90,00 of distributors such as Tiger Direct.

  I'm accustomed to Windows XP and have never used later versions of Windows. It is popular wisdom that Win 7 is greater than Vista in many ways, but it is $ 79.00?

  I want this computer to take over the online activities of my XP computer because XP is more dangerous. I'll keep my XP machine and put any contact with the outside world when I'm pretty confident with a new OS. The HP machine will not be called to lift heavy objects - but that could change over time, as the HP is easy to upgrade.

  Given the description of my situation, it would be more prudent to get Vista Business on Win 7?

  Extended support for Vista is scheduled for completion in 2017, where I would then face the same problem that I have now with XP and I would find myself looking for a new OS once again. Win 7 will be supported until 2020. In the coming years a new version of Windows will be better than Win 7 to the point where I don't want to change operating system before 2020? This HP computer will be obsolete before then as to makes it unusable?

  There are a lot of these questions without reply. The essential is that I'm a good sobbing market and I eventually get more for my money on a copy of $11,00 of Vista or $90.00 for Win 7?

  Beyond that, I have other questions, but I'll fix it in another post. I went too long in this one!

  Thank you for your interest!

  Grant

  Hello:

  I have a dc7800 CMT (E8300 processor) that I bought for my wife and upgraded to W7 because I got an upgrade to W7 pro I used no license.  I installed 8 GB of PC2-6400 memory and use a graphics Radeon HD 6570.

  I have for all of Vista Business 64 bit recovery disc to restore the original operating system should I decide to donate or resell the PC some days.

  I had the other dc7800 CMT (processor E6850) for my mother and order the recovery disks Vista Business 32 bit for it.

  Now, you can have a choice of the floppies to install Vista Business 32 or 64-bit.

  The set of recovery disks you get should have included SP1 (mine do).

  Then you will just need to DL SP2.

  It was the first thing I did once Vista was installed before that I made another anytbing to download the Setup file of Vista SP2 Standalone directly from Microsoft.

  If you do not ever plan on installing more than 4 GB memory, then the set of 32-bit recovery diskettes will suffice.

  I put 4 GB of memory in the PC of my mother because I had 4 x 1 GB of PC2-6400 memory, laying around.

  Windows 7 is a better operating system.  I call it "Vista that works."

  But really the main differences are:

  1 Vista seems to use more memory to run than W7, so more memory, you can throw to Vista better it works.

  2. the disk defragment tool seems to take forever to work.

  3. a few other minor quirks which I was able to use a few settings to make it better.

  I have used many of the settings on the link below and my mother PC works fine on Vista Business 32 bit.

  http://www.thewindowsclub.com/make-Windows-startup-run-Shutdown-faster

  I have disabled Vista Disk Defragmenter and use free Auslogics Disk Defragmenter that works just great.

  If I don't have a W7 license for use, I would have been perfectly happy under Vista Business dc7800 of my wife.

  I run Vista Business on an old notebook nc6400 and it works very well on that too.

  Then... IMO, I have just spend the $11.00 and go with Vista. If you like it, then you have saved $ 90 million.  If you have not, you buy W7, and you may have professional Vista recovery discs use one day as I want.

  A few final thoughts on the PC in general...

  1. make sure emulation sata in the BIOS storage section is set for RAID and IDE not.  RAID will be performing hard drive because it can take advantage of the native command queuing in RAID mode and it cannot in IDE mode.

  Many of the dc7800 are used in enterprise environments and have been downgraded to XP Pro. I would not be surprised if a large number of defined system IDE controller administrators when they set up their corporate images, because if they understand not drivers SATA RAID/AHCI necessary necessary in their corporate images for this and later models, their image it not install if the BIOS is set to RAID mode.

  It is the only native command Queuing does.

  http://en.Wikipedia.org/wiki/Native_Command_Queuing

  2. set the boot order to boot from the hard drive first.  Who's going to shave a fraction of a second startup time.

  You can always press the F9 key at the beginning of the HP welcome screen to boot from another device.

• Upgrading a DC7600 Convertible Minitowers - how far can go?

  I have a DC7600 CMT.  I understand HP uses a bios locked and there are limits on what you can do with the MB.  What is the most I could mistake this thing?

  What is the best processor I can go to?

  Assuming I am running Win 7 x 64 how much memory can I install?  Specifications say 4 GB max, is this still true or will it take 8 GB or 16 GB?

  Is its edge 5.1 channel?

  The power supply can be replaced?  What are the limits?

  The motherboard can be easily replaced?

  Support SATA 6 GB/s?

  Presentation and internal specifications. (only accepts the P4 processors): http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&objectID=c00374051&jumpid=reg_R1002_USEN

  The device comes with WIN XP SP2. There is NO support for WIN7. He doess let Vista 32 bit.

  Here is the service manual and upgrade, see pg data memory for 2-9. (4 GB max).

  The block of POWER 365 w is an atypical design. The only upgrade, I found was http://www.atxpowersupplies.com/365-Watt-Power-Supply-Delta-DPS-365BB-A.php?psu=437800-001-DC7600CMT 400W

  If you could change on the motherboard, you lose your OEM WIN XP authentication. Guide parts with numbers:

  http://bizsupport2.Austin.HP.com/BC/docs/support/SupportManual/c00404225/c00404225.PDF

  No, it does not support SATA 6 GB/s.

• HP compaq dc7700 convertible m: hp compaq dc7700 convertible minitowers no display

  Hi ive just got out the attic of my old pc, not connected my monitor and theres no display at the entrance.

  I remember having the same problem when I got it about 6 years ago first lol, I noticed in the box there is an adapter I plugged the wire in and then put it in another port (don't remember which) and display on monitor

  Problem ive got now is I seem to have lost this adapter and do not know what it is that I'm actually looking to buy another. Any ideas what it is?  Every day spent online search with no luck not even save the loft trying to find

  Thanks in advance

  The DC7700 CMT has a standard VGA video output and the only non - VGA card is the DY674A, this card would require an adapter to use a standard VGA monitor.  Look at the back of the DC7000 and monitor cable plug. Is this correct?

• HP Compaq dc7700 Convertible: I want to set the sound card

  I have HP Compaq dc7700 Convertible Minitowers PC computer (REF: RV742EC) and the operating system is windows 7 ultimate and I want to set the sound card, I want to help?

  Hello

  Please try:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=wk_128612_1

  Kind regards.

• How can I correct "processor not valid update firmware" I have a compaq dc7600 cmt C2C6260Q93

  My m/c is a HP Compaq dc7600 CMT (C2C6260Q93).

  I replaced the processor 2.8 with intel (R) pentium (R) D CPU 3.00 GHZ / 4 M, during startup, it gives the message "missing or not valid processor microcode update.

  My motherboard is HP (C) 2005HPDC can you help me solve this problem?

  Thank you...

   

  You are the very welcome.

  Please read this guide to make a USB flash drive bootable.

  http://files.extremeoverclocking.com/file.php?f=197

  You must download and install the HP USB format by the link tool there is on the Web page.

  Use the tool to format and do a usb flash drive bootable.

   

  Then, you will need to download Windows 98 DOS files from the link there is on the Web page.

  Then, you copy and paste the files BACK of Windows 98 in the bootable flash drive.

  
  Then you download and run the update of the firmware from this link.

  http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=472278&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253DPSG_I23753_109013%257CswEnvOID%253D1093%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  You will now see an instruction page after you run the update of the firmware.

  Under the section titled USB Flash Media Micro Code flashing in the BACK, select BACK Flash happy folder view.

  Copy all the files on your USB drive bootable.

  So, to summarize...

  1. you have a bootable USB key with the HP format tool

  2. you copied files BACK of Windows 98 in the bootable flash drive

  3. you have copied the contents of the flash HP firmware BACK on the bootable flash drive folder.

  You are now ready to update the firmware.

  Insert the flash drive into a USB port.  Turn on the PC and at the beginning of the HP welcome screen, press the F9 key to get the start time menu.

  Select the boot from USB drive option and press the Enter key and the PC should boot from the flash drive on.

  Now you need to know a few basic DOS commands.

  You should be at the command prompt.

  At the command prompt, type the FLASHBIN.exe command and press the Enter key.

  Then follow the instructions on the screen to update the firmware.

• Attach two headphones listening usb with a computer microphone compaq laptop with windows vista.

  I'm trying to attach two usb headsets to a computer compaq laptop with windows vista.  A set of works of helmet very well but the other does not until one is removed.

  Hi dmilten,

   

  In Windows Vista, you can get her out only 'default' and a 'default' endpoint.  Applications can play at all (and output record of any entry), but by default, they will use only 'by default' entry and exit.

  Outputs audio multiples are not supported by Windows Vista. It's normal. However, you can contact the manufacturer of the equipment for other possibilities.

  He may want to know:

  You can configure your Media Player to play a default device

  In Windows Vista, you can configure Windows Media Player to play an audio device specific.  Tools | Options | Devices | Speakers | Properties | Select the audio device you want to play.

  Reference:

  http://social.msdn.Microsoft.com/forums/en-us/windowspro-audiodevelopment/thread/a9241198-9e54-4358-8608-0a21163e0654

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Graphics card for Compaq dc7600 cmt

  Hi people

  just joined this site (sorry if this question a thousand times), I just bought a Compaq dc7600 and there a supply 365 w, I want to put a new graphics card to play some games (especially old) can someone tell me a decent graphics card that will work with this power supply.

  Thank you

  Sarra

  Hello

  You might want to look over the following video cards from your PC only diet 365 w:

  $80--->NVIDIA GT 440 25.6 GB/s - single slot width

  $130-->NVIDIA GT 545 43 Gbit/s - single slot width - might be difficult to find but perhaps only in the store

  An older but great video card is NVIDIA GT 240 1 GB DDR5 - 54.4 Gbit/s and a width of single card. This card does not support DirectX 10, which is eventually used in some of the latest PC games but it's a great performer.

• I'm working on a HP Compaq dc7600 compact computer with a BIOS password

  I'm working on a consumer HP CS 1900 post that contains computers HP Compaq dc7600 small form. On a computer, the battery holding the BIOS is released and the date and time must be reset in the BIOS. The configuration of the BIOS is password protected and I don't have any idea what is the password. I tried to go beyond it with a password BIOS HP chip resetter, but when I'm in the configuration it still doesn't let me change the date and time. Should I just reflash the BIOS? I bet that even after it is flashed there is going to be password protected. I left the battery for a few days and changed the rider of neighboing etc., but it is still protected. Is their a manual/doc/pdf that could respond to explain/identify the BIOS password?

  Hello:

  I don't know if it's me or the HP support site, but I can't seem to him.

  That's what you need to do to clear the BIOS password on a dc7600...

  1. turn off and unplug the PC. Unplug everything plugged to the computer. Keyboard, mouse, monitor, printer,... everything.

  2. press the power button to drain any residual power from the PC.

  3 open the case and locate the Green password on the motherboard jumper.  On the WTO, it is very close to the primary SATA HARD drive data connector.

  There is also a green light about, but of course that will be turned off for you.

  4. in any case, locate this jumper and remove it and place it somewhere for more security. Some people just put on one of the 2 pins. I prefer to remove it.

  5. now connect the cables. etc and start the PC. The password must now be provisioned.

  6. switch off the PC and replace the Green jumper on the two pins and everything back together.

  Fixed.

  Paul