switch control

Similar Questions

• Communication satellite U500 wifi switch control does not work

  Hello

  I have problem after update of the operating system from Vista 64 bit to win7 64-bit. The problem is in the wireless communication switch command before notebok. When I was with win vista, it works fine, post off - wifi off and post-wifi on (without restarting). But when I updated to win7 and install all the drivers of toshiba upgrade dvd, my wifi switch works as follows:

  When I turn on notebook with wifi off button - its turned off all the time and the wifi does not work and fn + F8 (shortcut key for wifi) does not work too. I have to restart the PC with wifi switch in position-the wifi works fine and fn + F8 is able to turn on and turn off the wifi. But that put the material do not react to pass and - diode LED is always on (in case when I start the pc with position control on and in the case where is when off wifi LED is not clear and switching does not work).

  I've updated wifi realtek drivers but still it does not work. IAM verry sorry for my English. I was looking into Toshiba diagnostic tool and there is no modem device, but yes, wifi is perhaps problem here?

  Thank you very much for the reply. Tom

  Hello

  Different Satellite U500 (and other models) supports various wireless network cards, and that's why you'll find also different WLan card drivers.

  Your U500 seems to be equipped with an Intel Wlan card and here you can also download the right Intel Wlan card driver for this card:
  http://APS2.toshiba-tro.de/WLAN/

  Welcome them

• keyboard volume and switch control wireless - HP Pavilion Entertainment Notebook

  My volume control keyboard & wireless switch (to touch those at the top of the keyboard) has just left the other day of work. I can't understand how do I know if I disabled something accidentally or what. Reset did not help. The only thing I did differently this day was to connect my laptop via a cable and stops the wireless. (I usually work wireless).

  Laptop HP Pavilion dv6-2157sb

  Windows 7 64 bit

  Thanks in advance for any help.

  Hello

  Problems with the capacitive band can sometimes be helped by doing a Hard Reset as follows.

  Shut down the laptop, unplug the AC adapter and then remove the battery.  Press and hold the Power button for 30 seconds.  Reinsert the battery, connect the power adapter and start Notepad.

  Kind regards

  DP - K

• Switch control Boolean to false automatically after a set time

  I'm trying to control when I register given by the presence of the user press a Boolean control on the front panel. I want the data to be saved for only 3 seconds and having the Boolean control automatically enabled to false so that the data will stop recording and control changes on the front but does not prevent the execution of the VI. The reason is that I want to have the user to create a settings file for a laser used outside of labview where entered the user through digital controls the current settings of laser and a wavelength of laser meter reading is found measured and saved in labview. So after that the data records for 3 seconds the user would input new parameters for the laser and then save the new configuration of the meter wavelength and repeat this operation several times.

  I tried a case hang as seen in the attached VI and you have also tried a state machine with control of ENUM. I can't get this thing to work. Any help would be appreciated.

  Thank you

  Hello

  Easier implementation is to have a state machine. You would have a State to collect data for a specific timer and another State to exit the VI.

• Stuttering scrolling, switching space, the mission control

  I am running OS X El Capitan on a Mid-2014 rMBP with the discreet graphics card, and recently I've been doing serious stuttering through the BONE. Scrolling in Safari is nervous, gal space office, launch of mission also switching control is not smooth. Of course, my material should have no problem with the operating system relative (I can play games on high settings), so I don't know what the cause is. Nothing in the activity monitor seems to be hogging a lot of resources. Troubleshooting tips?

  Hi Plasma Prestige,

  Thank you for using communities Support from Apple. I'm sorry to hear that you are having these problems with your MacBook Pro. If you continue to have graphics or problems of lag through several UI elements user and you see no problems evident in the activity monitor system resource, you can try to test in the two Safe Mode and a new user to test to see if the problem persists. You can find information and the steps in the following articles useful:

  OS X El Capitan: start in safe mode

  Try safe mode if your Mac does not end commissioning - Apple Support

  How to test a question in another account on your Mac - Apple Support

  Concerning

• Other ways to access to the control center

  I'm a quadriplegic and can't touch to the iPad, but I use the switch access. That leaves several things that I can't because you have to do some kind of shot or another action.

  I was trying to find another way to bring up the control center, since I can't slide with my finger. I actually found a several months ago and put in a recipe under switches, but something went past and disappeared and I don't remember what I did. Any ideas?

  Also, I need to be able to implement all applications running in the background that must be killed. I can't double click on the home button. It any suggestions?

  I use the command with 2 switches. If that helps anything.

  Thank you! -Doug

  Hello WDMaples,

  Thank you for reaching out to the Community Support from Apple. I know how it is important to be able to access all the features of your iPad, and I have an article that should help you to implement the control you are looking for with your switch access. This article should help guide you through setting up the recipe to replicate hitting swipe and double click on the home button.

  Switch control: Basic Techniques

  If you experience any problems or have any questions, please let us know. The entire community is here to help.

  -Best regards-

• On my ipad3 I rectangles blue moving around the screen. Momentarily switches to an article before moving on. Very irritating

  I have an iPad 3. Model MC707B/A. Version 9.3.2 (13F69).

  Blue rectangles are continually moving around the screen from one section to the other. Also a blue stripe sometimes crosses the screen. Has started yesterday for no apparent reason.

  I have tried rebooting with no luck. Helpline Apple could suggest only reset to factory settings. Does anyone have a less radical solution?

  This is one of the accessibility features. It's the switch command. You will need to go into settings > general > accessibility > switch control and turn it off. It is possible, that's what the setting is triple clicking the home button. Try triple clicking again and see if that if he stops, otherwise, use the road that I explained earlier.

• Blue contours appeared and I can't control my iphone 5 s. I can't go to settings. I triple click on the button "home" and gives a message to go into settings and enter the password but I can't get to the settings. What does not work? Thank you

  Blue contours appeared and I can't control my iphone 5 s. I can't go to settings. I triple click on the button "home" and gives a message to go into settings and enter the password but I can't get to the settings. What does not work? Thank you

  The blue plan is switch control.

  s http://gettecla.com/blogs/News/15538916-what-is-switch-control-mode-in-apples-IO

  Triple click to get rid of him.

  "Siri to the rescue.  I said turn off the control switch. »

  Re: How to disable the switch control

  I don't get a request for an access code.  What is a school system?

  switch control

  Settings > general > accessibility > switching control

  R

• PAVILLION DV6: INST W10 NO WIFI CP SWITHC DOES SWITCH OFF THE POWER AS SOON AS TURNED ON AIRPLANE TOGGLE SW HDWR MODE...

  Installed w10 CLEAN(FREE UPGRADE) WIFI NOT WORKING HARDWARE SWITCH TOGGLE AIRPLANE MODE (led does not change, but software reinforces airplan toggleing mode, WHO ALSO WORKS IN the PANEL.)  USING WIFI SWITCHES CONTROL PANEL WILL ALLOW ME TO MOVE the INDICATOR, BUT IT MOVED SIMPLY the right side BACK.  ETHERNET USING WORKS NOW.  Bluetooth not active either, but everything else works fine

  function + F12 does nothing.

  removing the broadcam wifi and restarting brings just it back right.

  update the Windows says that the best driver already installed...

  any help will be greatly appreciated-thanks in advance!

  It came from what the original hard drive started failing, replaed with a SSD and bumped the ram up to 16 GB (at a time of Crucial) and ordered HP Recovery Media kit 67889-002-cd1 and 683958-b22 and if they follow-up procedure, the result would not start as the dod kit come with a boot disk to continue with a restore bootable , I aircrcrack a free 10 WIndows upgrade-following clean install and started in windows 10 successfully with declared wifi and blue tooth issues.   BIOS has been improved in troubleshooting the original drive and see updates.  I have installed and run sp74656...

  It is a dv6-6c10us (A6Y49UA #ABA)

  Thanks for your instructions detailed, I followed each in explicit order and still no wifi or bluetooth, so everything worked fine before the hard drive has begun to show intelligent questions, I decided to give the system recovery try together, I bought one another, or ten years...  Eventually I succeeded and adds this post of my DV6 on my network wireless thanks to recovery fully functioning of Windows 7!  The question proved that the recovery program would not attribute a system partition large enough to hold all of Windows 7. He would not move (or be fixed with manipulation) that he was trying to put a gallon into a pint container.

  It took me three attempts to penetrate deeply enough in what had happened to see it happen, but the recovery media composed three partitions-a great unallocated one or two small (from memory less than 100 MB) entire system and recovery.  Although the size of partition extended in every attempt, they were never big enough to contain everything they were supposed to.  Once I used a Windows 7 Home Premium disk to initiate a clean install and then set the partiction to a blank disc size manually and then run the recovery everything falls into place!   You might wonder why I didin't simply ise Windows 7 install from disk... too many exclamation points in Device Manager! -No driver found - nothing worked (worse than windows 10)... I could not update or import from the application and driver recovery CD that accompanied the system recovery media either! Therefore, I ran through the recovery process and it worked! Number 10 Windows always is the lack of a legacy driver appropriate for the wifi equipment, but ultimately the support of Windows 7 recovery worked and the laptop is perfectly to the point!   As soon as I finished posting here and sew all of HP and windows updates I will establish a recovery image and do.  I appreciate your help and hope, which has been posted here will help someone else - and save them time!

• How to synchronize the start of IT and relaxation the Scan list (DAQmx Switch)

  Hello

  I want to measure samples of N to the AI0 of Council NI PXI 4461. The measurement starts on a rising edge of a digital triggering provided to the PFI0 of the same Board. The measure is configured with samples of N/2 pretrigged. So far, everything is under control...

  Using an NI PXI 2567 Board, the signal applied at the entrance the 4461 (AI0) switches between a V2 and V1 signal. I would like to synchronize the switch between the two signals with the trigger signal applied to the input of the PFI0 Governing Council 4461. In order to obtain samples of N/2 of V1 and V2 samples N/2. Synchronization of 1 to 5 ms would suffice!

  My question is how to synchronize the start of acquisition of AI pretrigged of 4461 with the switch control given by the Council of 2567?

  Thank you in advance for your help...

  PS: the configuration of the system is:

  -LabView 8.5

  -Chassis PXI-1044

  PXI-4461 on slot 2

  Module 4-slot PXI-2567

  Hi Frederic,.

  I came back to this recently and used the following examples to run the desired synchronization.

  PXI-4461: Acq & graph tension-Int Clk - dig Start & Ref .vi

  Samples per channel = 1000

  Rate (Hz) = 10000.00

  Start the trigger Source = / [name of the instrument DAQmx] / PXI_Trig0

  Onboard start = fall

  Reference Source Trigger = DAQmx Device Name] / PXI_Trig0

  Reference edge = fall

  Trigger samples = Variable (100, 500, 900)

  PXI-2567: Switch Scaning-SW Trigger.vi

  Advance the output terminal full = / [name of the instrument DAQmx] / PXI_Trig0

  Scan list = / [name of the instrument DAQmx] / ch0-> com0.

  Scan list = / [name of the instrument DAQmx] / ch1-> com1;

  Hardware configuration:

  The PXI-2567 module controls an external relay that switches between the voltage of 5 V on ch0 and ch1 0 V.

  The PXI-4461 connects to the COM of the external relay and therefore reads 5V when ch0 is connected; 0 v when ch1 is connected.

  Procedure: The above examples are used in the following procedure.

  1. run the PXI-4461 VI.  A start trigger (falling edge) is necessary to start collecting samples before firing.

  2. launch the module, PXI - 2567 VI.  When ch0 is initially (and immediately) on com0, a trigger is sent to PXI_Trig0.  The PXI-4461 will begin to acquire samples before firing.

  3. - click on the "Connect to the next" button on the front of the PXI - 2567 VI module.  This sends a trigger to entry software for the PXI-2567 module and the transitions of the scan for ch1-> com1 list.  Once the PXI-2567 module remains (debounced), advanced complete relaxation is sent on PXI_Trig0 for the PXI-4461.  The PXI-4461 will begin to acquire samples after outbreak.

  Note: Instead of the trigger of the software entry, an external input trigger can be used (e.g. PXI_Trig1).

  Results:

  > Before instant release of samples = 100

  Delay is caused by the time of actuation of external relay.

  

  > Before instant release of samples = 500

  Delay is caused by the time of actuation of external relay.

  

  > Before instant release of samples = 900

  Delay is caused by the time of actuation of external relay.

  

  I hope that the attached screws and the explanation above helps you and/or other customers who have this problem.

  Best regards

  Chad Erickson

  Switch Product Support Engineer

  NOR - USA

• Stripchart control, strange high CPU usage

  Hi all...

  I had a strange problem with stripchart control.

  In the past, I noticed that 'sometimes' different programs I wrote had an abnormal CPU utilization, not justified by any activity that they were really productive.

  Finally, I got the time to track down the problem and build a minimum sample code.

  This program has a panel with a stripchart control and two command buttons.

  Buttons simply erase the stripchart and add one point to the empty stripchart.

  int CVICALLBACK ControlCB (int panel, int control, int event,void *callbackData, int eventData1, int eventData2)
  {
      switch (event) {
          case EVENT_COMMIT:
              switch(control) {
                  case PANEL_BUG:
                      ClearStripChart(panel,PANEL_GRAPH);
                      PlotStripChartPoint (panel, PANEL_GRAPH, MAGIC_VALUE);
                      break;
  
                  case PANEL_NOBUG:
                      ClearStripChart(panel,PANEL_GRAPH);
                      PlotStripChartPoint (panel, PANEL_GRAPH, NOT_SO_MAGIC_VALUE);
                      break;
              }
              break;
      }
      return 0;
  }
  

  I found that adding 'special' values to the stripchart starts a background activity that consumes a significant amount of time processor.

  In this screenshot you can see what happens on my PC, when I click on the command button "Bug".

  The special value here 42.22 but I bet there are thousands other with similar behavior.

  At a single point, the le stripchart stripchart shows nothing else that changing the scale of the axis Y.

  

  By clicking on the button 'No Bug' command inserts the value of 100.0 and no bad behavior occurs.

  Just to confuse the ideas, if you press "No Bug" and then "Bug", the bad behavior does, too.

  It's probably an interaction between the autoscale to axis Y, the initial values and perhaps the "name of the scale. I don't have the time to explore all combinations and can be a minimum solution.

  In my applications, I finished by making the set "by hand".

  I tested the program on five different PC, Core 2 Duo CPU running XP, Vista, and 7 (Italian), compiled with CVI 2010 SP1

  It is the complete project.

  The kit distribution for the project (without sources) can be downloaded here: http://dl.dropbox.com/u/23913808/CPUeater.zip

  There was a bug in the map graphic/band code which could cause without end bike when you try to resize a chart axis that had a visible axis label. It has been fixed for the next version of the CVI so unfortunately you will have to wait a bit.

  There are two possible solutions:

  (1) disable the axis label. If it is not displayed, this loop can ever occur.

  (2) to activate the fixed plot area and play with the left and the width of the plot area for hover over everything to the right a little more. The problem was introduced when the Microsoft graph chart / think the label becomes too close to the border of the chart and tries to reposition the label. Unfortunately, the code was a bit buggy and etiquette have stood in the exact the same task, but we weren't checking to see if we had already tried to reposition the label, and so he cycled constantly.

  Sorry for the inconvenience.

• How to control the implementation of devices that cannot run any agent, such as thin clients, printers, and other press.

  I have an OOB layout that has all the ports from the switch controlled by the same profile. I would like to be able to place clients on a network, printers on one another and tell on another unix systems. Right now I have a filter that lets the clients on the network, and they are put on the vlan by default to access via port profile. The filter is by MAC address.

  What is the only way we can do that?

  Can we put things on different networks, using this method, if so how?

  Any help would be appreciated.

  Hello

  When you create a new filter for a specific MAC/IP, we should select the "Access Type" for this device.

  As shown in the attached screenshot (taken from the NAC 4.8), we also have the ability to define the type of access based on a specific user role.

  Kind regards

  Fede

  --

  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Cannot connect wireless or even turn on the wireless "switch" on my computer

  I recently installed a copy of Windows 7 Professional, yet the installation, I couldn't have the wireless network to connect to what either.  The first thing I noticed was that my wireless button (which is a touchscreen as a device on the top of my keyboard) was not on, can I turn it on, or do I not have the fn + f2 option.

  My computer is a HP Elitebook 8440p and regardless of what precedes, I proceeded to install drivers wireless on HP support site, they had to choose some and I ended up trying 3 which did not work.  I found a page of networking which showed these drivers wireless with a connection of sorts but closer examination revealed that the problem lied with simply turn on my wireless switch.

  LAN works fine (I'm here now) and the wireless switch control active if I turn on my any and hit him (orane to blue towers), but otherwise, I am astonished.  I don't think that the router is the problem, but it is a 'Fast' model... that's all I know at this point, although I'll try to find the type of exact model if its important.

  I think it's information pertienent, thank you for any help you can provide!

  My computer shows management I installed the drivers...

  In fact, I found the answer (I hope help you someone else with your post if the time is not lost)

  My wireless is fine, it turns off when I plug my ethernet cable.

  Appreciate the answer however.

• Mysteriously appeared blue outline

  My iphone 6s this morning began to have a rotating box overview blue up and down and will not stop until it runs through several times on a page.  Then stops.  When I opened a new page, the blue outline box reappears and runs across the page.

  Try this...

  Tap Settings > general > control switch and then switch Control Switch OFF.

• Failed to start service to Xcode because of the license agreement

  Since the upgrade to 5.0.15 server, I have met some problems trying to start the service of Xcode, which prevents good start:

  When I tried to select Xcode by clicking Choose Xcode in the server window, after I chose/Applications/Xcode, I saw the message 'preparation to set the server to Xcode' and Xcode was launched. Xcode then displays a message indicating "Xcode requires permission to use accessibility for the user interface controls. "Click on request access to open system preferences add Xcode to the list of allowed applications to control your computer." When I click on Request Access, nothing significant happened. I opened System Preferences > accessibility manually, but did not know where to add to the list of Xcode. I didn't see any list under Interacting > keyboard, mouse and Trackpad, or switch control. None of the other sections seems to contain a list of applications either. After some digging around, I noticed that there is an entry in System Preferences > Security & privacy > privacy for Xcode for assistance that has been disabled. Check the box seems to have accomplished the goal here (fingers crossed).

  Server, and then displays the message "you must accept the terms of the licenseXcode. Restart Xcode and accept the software license agreement or choose another version of Xcode'.» When I launched Xcode, however, he showed not the license agreement. Delivering the xcodebuild-license sudo and sudo xcodebuild-license accepts commands in a terminal window do not appear to do this in the right way, because the server continues to display this message every time I chose the Xcode application.

  There must be some reason Xcode does not display the license agreement when I run the application, any server insists I did not accept the agreement despite having accepted several times.

  Any ideas?

  Potentially a bug known, according to the affected versions.   (Look for the license in the Xcode release notes).

  If the approach in the release notes does not work and If this existing thread does not work...

  .. then see if the brute force approach works...

  Turn off of Xcode,.app services.    Xcode remove the system.  Reset.  Reinstall Xcode, a new download (current) or a (current) version stored on another local system, launch Xcode, accept the license.  Then configure Server.app and see if he's happy now.