Synchronization of data acquisition

Similar Questions

• synchronize two loops for written tdms data acquisitions

  Hello

  I have two loops of different data acquisition. A slow acquisition of CAN (10 s/s) and an analog acquisition faster (30 samples taken at a frequency of 300 Hz), I need to synchronize these data for tdms writes for later analysis in DIAdem.

  My example and the result in the DIAdem channel list is attached.

  Thanks in advance!

  Magnus

  Magnus,

  for a professional solution, you do not want to synchronize the devices on a hardware level. Since the material CAN work differently to 'traditional' DAQ devices, there are important things to take care of.

  Please look in the viewfinder to LV example for the word "CAN". For example, you can choose the example 'several cards CAN and DAQmx map Wfm Input'.

  Norbert

• Card FPGA and data acquisition synchronization

  Hi, we are control and data acquisition of several hardware devices (including Photodetectors and translational stages). Until last week, we used all the controls and acquisition using a PCIe-7852R FPGA board. However, we decided to move the acquisition part to a PCIe 6363 DAQ card to improve the sharpness of the tension. During the test, I found that the internal clocks in the FPGA and the DAQ cards are slightly inconsistent (not just a phase delay, but a difference in the period).

  I know because I have generated a square wave (period = 20) using the FPGA and gains using the data acquisition card (at a rate of 200 kHz, that is, 1 taste every 5). I have observed acquired place shifts 5 every 5 seconds approximately. Such a change does not occur if the production and acquisition is done using the same Board. Therefore, the only explanation is that the data acquisition and FPGA cards clock frequencies are different. According to my calculations, the percentage difference between their time clock must be 5/5 s = 0.0001%.

  Therefore, I wonder if there is anyway to synchronize clocks between them. Or, is it possible that I can drive the FPGA clock-based DAQ hardware, or vice versa? Also, please let me know if there is something trivial as I fix.

  Thank you very much.

  Kind regards

  Varun

  Hi Varun,

  my post was only one solution...

  Your data acquisition card may take an entry to control sampling of trigger. In this mode, samples draw on a rising edge of the external clock signal. As long as you stay within the limits of the DAQ (100 MHz for your card) material sampling works perfectly. There are even examples coming with LabVIEW explaining how to program your data acquisition card...

  This mode use you your FPGA as clock source sampling for data acquisition. Both will run on the FPGA clock in sync. When the FPGA is a bit out of 40 MHz, so it won't matter because both devices are triggered on the same clock signal...

• data acquisition won't taste at the specified rate

  Material: C - DAQ 9178, AI 9239, inside a servo and an encoder potentiometer module

  Setup: I use the 9239 to measure the angular position of my servo and encoder of trees by streaming came pressure pot of the servo and my encoder. I put the sampling frequency on the DAQmx - Schedule VI to 100 Hz.

  Problem: I don't think that my DAQ is sampling data at 100 Hz because my VI registers more than 10 000 data points for a 10 second test. In addition, every time I have save my data in a text file, the vector of time my test data resets after a number of iterations.

  To debug, I tried the following configuration:

  I've defined the sampling frequency of 100 Hz (or is that s/s?), the samples per channel (size of buffer for continuous mode) at 2000 samples, number of samples per channel up to 10 and loop milliseconds timer on my VI at 10 m accordingly, data acquisition would send 100 samples per second (or 1 sample every 10 ms) on my PC buffer (which could store 20 X that amount). Then LabVIEW would read up to 10 samples per loop iteration (which is itself ~ 100 Hz) and work with these 10 samples inside the loop. However, since the loop is operating close to the sampling frequency of data acquisition, then LV should only work with 1 sample each iteration of the loop (100 Hz / 100 Hz)-not the 10-sample-max that I specified.

  However, I stumbled on "error-200279: the application is not able to cope with the acquisition of material" when I ran the program. Why?

  My code and materials should be easily able to cope with data acquisition - at least the way I put it in place

  This whole situation wondered my fundamental understanding of data acquisition timing, so I would really appreciate an explanation of exactly how to deliver DAQmx uses data synchronization, why my DAQ sample at 100 Hz, and how can I fix the calendar specified by the user.

  Thank you!

  aeroAggie wrote:

  The C - DAQ 9178 there some minimum sampling rate I will not meet?

  It's actually the 9239 that limit your sampling rate.  Read the data sheeton page 5 there's available data rates.  In short, your data rate allowed is 50kS/s / n, where is goes from 1 to 31.  50 k/31 gives you 1.6kS / s.  So, it's the minimum sampling frequency that can be used.

• HP laptop - 15-r224tx: PCI controller of Data Acquisition and processing for HP for laptop - 15-r224tx

  I get upgraded my laptop (HP for laptop - 15-r224tx) for Windows 10 but I can't find the driver for the controller of PCI Data Acquisition and Signal Processing. Please help me find the right one.

  Thank you!

  You are the very welcome.

  It is the latest version of the W10 driver for this card model... see if this solves the problem, if you have not already installed this driver.

  This package contains the installation package driver for the controller wireless LAN Realtek RTL8723BE/RTL8188EE in the laptop models running a supported operating system.

  File name: sp72517.exe

• How to synchronize the data of nike nike + ipod nano 7G

  Hello

  I use my ipod nano7 for 3 years, but I've never synced nike application data.
  But I started to run. I want to synchronize the data in my profile nike +.
  I get no pop up in itunes application if I want to synchronize data from nike.

  Help, please.

  Thank you

  Check on the screen of the iPod settings in iTunes...  Select iPod in iTunes (click on his horizontal bar device button to display the screen of the iPod settings.  The side left (in the sidebar), under settings, you see Nike + iPod?  If you do, click it.  Do you see a framework for initiating sends it data Nike +?  Mine is already set up (with my 5th generation iPod nano), so I don't know what it looked like before.

• PCI Data Acquisition and Signal Processing controller driver

  I installed win 8.1x64 on my HP Probook 450 G2, but miss me the driver of PCI Data Acquisition and Signal Processing controller.

  Can you please help?

  Thank you

  Leontina

  Hello:

  Please see if installing the Intel Chipset driver installs this device.

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?DwnldID=20775 & lang = eng & ProdId = 816

• Z600 Workstation: workstation Z600 missing of pci data acquisition and signal processing controller driver

  I just installed Win7 Pro x 86 on my Z600 workstation.  It was an upgrade to Windows XP Pro.  I'm missing the driver for PCI Data Acquisition and processing of the Signal and Hardlock USB 1.02 controller in Device Manager.  Can someone help me find these drivers.  I looked on the page of Support/Drivers for this model, but could not find anything.

  Hello

  You can get assistance on the HP Enterprise Business Forum since you have a professional worktsation.

• HP 240 G4-328TX: need driver for PCI and Signal Processing controller HP 240 G4-328TX Data Acquisition

  Hello

  Need driver for PCI and Signal Processing controller HP 240 G4-328TX Data Acquisition

  Can anyone provide me please the link for download it for windows 10

  Thank you

  Hello:

  See if this driver works...

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=7609938 & swItemId = ob_153701_1 & swEnvOid = 4192

• Pavilion TS 17-g099nr: PCI Data Acquisition and processing of the Signal Windows 10 x 64 controller driver

  Hi, it is impossible for the moment to install the driver for PCI Data Acquisition and Signal Processing.

  I downloaded the driver from Intel, and it did not work... I found a version of this site for windows 8.1 unupdated and it does not work.

  A little help?

  Thank you!

  Hello:

  It could be one of two different drivers.

  Try this one first, and then restart the PC.

  This package contains the Intel Chipset Installation utility. This utility allows the operating system to show the correct name for the Intel hardware that is installed in the Microsoft Windows Device Manager. This package is provided for the laptop models running a supported operating system.

  FTP://ftp.HP.com/pub/SoftPaq/sp75501-76000/sp75561.exe

  If this does not work, try this one...

  This package contains the driver which allows Intel platform dynamic and thermal firmware setting. Intel platform dynamic and thermal environment information system temperature and power use for the thermal protection of the system to work properly. This package is provided for the laptop models running a supported operating system.

  FTP://ftp.HP.com/pub/SoftPaq/sp75501-76000/sp75506.exe

• 15 - ac122tu: PCI of Data Acquisition and the controller driver of laptop HP 15-ac122TU signal processing

  Hi team,

  I just install windows 7 edition integral and peripheral Bluetooth windows 8.1 is not be detectable, when I search for problem that I came across this PCI data acquisition and Signal Processing controller driver is missing and a unknown device driver missing shownup in my result of troubleshooting. Please help me

  Please find the screenshot for your reference

  Thank you

  

  Hello:

  See if these drivers work...

  CQI PCI controller:

  This package contains the driver which allows Intel platform dynamic and thermal firmware setting. Intel platform dynamic and thermal environment information system temperature and power use for the heat of the system
  protection to work properly. This package is provided for the laptop models running a supported operating system.

  File name: sp71638.exe

  Bluetooth:

  This package contains the installation package driver for Realtek bluetooth in the laptop models running a supported operating system.

  File name: sp71288.exe

  Unknown dev:

  This package provides the HP 3D DriveGuard software (HP ProtectSmart Hard Drive Protection) for the laptop models running a supported operating system. HP 3D DriveGuard software protects the drive hard by parking the heads if cell phone accidentally falls, or is suddenly struck by another object.

  File name: sp71811.exe

• 15 - r235ne: SM bus controller / IBD DATA Acquisition and Signal Processing controller

  Hello team

  I am facing problem in finding the right driver for material below.

  1 SM bus controller

  2 IBD DATA acquisition and Signal Processing controller

  kindly help

  concerning

  NASIR

  Hi, Nguyen:

  Download and install the Intel chipset installation utility and restart the PC.

  The 2nd driver down on the left is the automatic installation file.

  https://Downloadcenter.Intel.com/download/20775/Intel-chipset-device-software-INF-Update-utility-?product=1145

• Data acquisition reading incorrect when you use a loop

  Hello

  I wrote a simple VI (00, 01, 10, and 11) output to a circuit connected with 4 resistors. Based on what value the ciruit receives, it passes current through a particular resistance. It is again entered in Labview and traced.

  The problem is when I send a particular value (i.e the 00, 01 and 10 and 11) and get that back, it's okay. But when I send and receive the consectively connected via the loop counter, they are incorrect (not synchronized with the number of the loop).

  I made sure that circuit works very well. It has something to do with the loop synnchronization, reset, value compensation, etc. can be.

  Please Guide...

  Change your DAQ assistant that reads to be 1 sample on request.

  Right now it is set for continuous samples.  And 10 samples at 10 Hz.  Then it runs and starts.  The next iteration, you send a new digital out, but the wait for 4 seconds.  When you read again, you get the next 10 samples that are put into the buffer of data acquisition, but now 40 samples have actually entered the DAQ buffer.  In time your DAQ buffer will be finally complete and raise an error.  In the meantime, you will continually read data continues to become more tainted by the iteration.

• Is it possible to change the name of data acquisition device?

  Hi all

  Is it possible to change the name of device of data acquisition in a pragmatic way?

  I wish I had at the beginning, when I start the data acquisition control a name that my .net program assigns to the DAQ card. Is this possible?

  Thank you

  Virginia

  Ashly thanks!

  Virginia

• motion control for vertical actuator and data acquisition

  Hello

  I am a researcher (a branch of civil engineering) geotechnical engineering and I have very little knowledge about the acquisition of control and data motion, so would need a lot of help from the experts OR. I have only knowledge base on these 2 aspects based on my reading of some materials on the Web site of NOR and youtube videos, so I hope that you bare with me . Here are my questions:

  I am trying to build an actuator which will be used to push a probe (a penetrometer with a load cell to measure the resistance of a soil sample), resembling the concept, photography in the attached file. I need to have these criteria for my system:

  (1) actuator, which can push the probe at speeds between 0.01 mm/s - 300 mm/s with precision and move the probe cyclically (upwards and downwards) in the vertical direction
  (2) load expected on the probe into the ground range: 0.02kN - 6 kN.
  (3) necessary to get the load cell load data and the speed of the probe.

  4) able to control the actuator to a PC (speed and posotion) and monitor data from transducers and data log time even the transducers.

  Guess my beginners is that I will need:

  For orders:
  (1) software - LabVIEW and NOR-motion assistant

  (2) controller - NI PCI-7342

  (3) driver/amplifier - analogue servo AKD Drive

  (4) motor - motor brushless servo AKM

  For the acquisition:
  (1) software - based LabVIEW development systems

  (2) amplifiers or other device - no idea what type on the conditioning of signals

  (3) data acquisition device - no idea what type

  Since I'm a beginner, is - that someone might recommend components (hardware and software) for the control and data acquisition. I'm on a tight budget, so I thankful if someone could help me to recommend components good enough to build my system.

  Thanks for your help.

  At these rates, you will need to run the sensor for the cDAQ.  You can configure the analog output on the Tritex nationally on the position.  There is an adjustable filter that you can set in order to get a clean enough to 300 Hz signal.  When you learn about the Tritex, make sure that let you them know what comms and e/s that you want to use.  If I remember, not all options have worked together.  The analog output may need to be my, but you can put a resistance through the acquisition of input data to get the voltage instead.  I don't remember all the details.  You should really not too much on the Tritex/LabVIEW side.  You will send your movement parameters (beginning of end of race, speed, position, accel, cut), and if you cycle (I believe you) or simply running in a loop.  You could also just be able to use the functions of jog.  When you get close to knowing exaclty what you need, PM me and I'm sure we can work something out with the drivers.  You need only the basics.  In fact, you could probably do this all your movements via digital and analog i/o.