T61p does not recognize the battery replaced

Similar Questions

• my computer dell laptop with windows vista does not recognize the battery what should I do?

  I have a computer dell laptop which will not recognize the battery what should I do?

  Contact Dell for hardware support.

• Satellite Pro 6100 does not recognize the single battery external power

  Whenever I have start Satellite Pro 6100 Win XP Pro with standard battery mounted and connected to the power supply computer laptop does not recognize the ext battery supply single supply and during 'start-up' goes into hibernation.

  By pressing the power on button laptops "wake up" and indicate that the battery is empty or may not even decide when completely loaded, then says connect the station even if still connected, looking under Toshiba console when it runs shows running on battery when still in the power of the ext?

  I have two batteries and both give the above symptoms even when I remove ext of laptop power always runs with power supply by battery but no light orange or green for battery.
  Any ideas?
  Concerning
  Phil

  Hello

  Is your AC adapter malfunctions or there is something wrong with the power supply to electronic s laptop.
  In the first case you could purchase a new compatible AC adapter and could check if the laptop can run successfully.
  The second possibility is a serious hardware problem, but in this case, the laptop must be checked by an authorized technician.

• Tecra M1 does not recognize the DVD drive after replacement

  I am trying to install a new drive CD-RW/DVD-RW on a Tecra M1; However, when the computer does not recognize the drive.

  Is there a solution to this?

  Thank you

  Colin

  For me it s case.
  I would say that the BIOS can't handle the new player properly because of the wrong master/slave/c-salt settings
  Readers slim for computers laptops support setting master/slave/c-salt settings and these settings can only be changed by changing the rider as on desktop drives.
  So it is very important that you purchase a compatible player and supported because disks with incorrect settings will not work.

  Before buying a car, you should ask the service provider to Toshiba for a caught player supported and compatible

• Satellite M50-A-110 does not recognize the new SSD?

  Hello

  I bought the M50-A-110 model and tried to replace the HARD drive by a Pro 840 Samsung SSD. The laptop does not recognize the SSD drive, so I sent him to the local Toshiba service for inspection.

  They discovered that the laptop does not recognize ALL of the latest SSD (they tried to Samsun, Intel, Crucial, Kingston and SSD Seagate). They checked, and I possible newer BIOS, so this isn't a problem, and the SSD worked fine on other computers.

  Someone knows how to solve this mess?
  Toshiba has a BIOS beta I could try?
  Any other ideas would be welcome.

  As a user of long date Toshiba, I must say that I am a little disappointed. I mean I work in it, and this is the first time that something like this happened to me with a new product.

  Hello

  I can't believe that Satellite M50 - A can not handle any of the mentioned SSDS.

  I upgraded my Toshiba laptop with SSD Pro 840. But before I did, the update of the firmware of SSD was necessary. Before the firmware update, the SSD has failed, after the firmware update, BIOS can handle the SSD.

  I would recommend to check the SSD for the firmware update!

• Satellite A30 PSA30E - BIOS does not recognize the HARD drive

  Hi all
  I have a Satellite A30 (PSA30E) and I start the computer. When I enter the BIOS it does not recognize the hard drive.
  Does anyone no what I can do?
  Is it possible to restore the BIOS?

  Thank you

  Hello

  You replaced the HARD drive by a new one or the BIOS don't recognize the old HDD?

  Usually if the laptop is not able to start and that the BIOS does not see the old HDD then I guess that the HARD drive is faulty.
  If the BIOS doesn't recognize the inserted new HARD drive and then either you ve bought is not compatible, or the size of the HARD drive is just too big.

  Please provide more info. You see error messages?

• Satellite A205: Vista & BIOS does not recognize the CD/DVD drive

  After a crash of the sudden family Vista system premium on a Toshiba Satellite A205 the system does not recognize the DVD CD - RW drive. Neither in Explorer, Device Manager, nor BIOS.

  Laptop is only a few months old.
  Have you tried the Toshiba check system - it ignores DVD disk check.
  Tried Windows Update - does not help.
  Tried registry fix - does not help.

  Cannot use the CD to reinstall all drivers - because it is not recognized.
  The DVD drive LED is on. If the disk looks ok physically.

  Does anyone have an idea what to do?

  Very strange what s
  Try this:

  Access the BIOS and set the default settings and save the changes.
  If it doesn't help then I put t see any other possibilities for contact ASP in your country for a CD/DVD drive control and possibly a replacement

  You said that the notebook is only several months old so I assume that the warranty is still valid and that's why everything has to be done for free

  Good luck my friend

• Windows 7 does not recognize the installation discs

  Hello

  I have a problem, and I don't know if there is a solution, but here goes.

  My laptop is a HP DV6-7029WM Windows 7, 64 bit.

  The hard drive was dead, and he was replaced last month.  I sent it to HP.  C is the hard drive, and was originally the recovery on D. Removable media were on E, and when I connected a USB stick or memory card reader it would on F.

  When I came back, hard drive was on C as it was originally, and there was no recovery drive D. D is now my removable media drive. When I put in a USB stick or a memory card reader, which is now on the E drive.

  After I bought this, I put the recovery on a USB key, but I've accidentally thrown out. (My mistake) So I ordered the installation diskettes after that I return my HP PC.  I had 2 DVD system recovery disks and an Application and a recovery DVD Drivery.

  I want to reinstall Windows back to the default settings. I put disc 1 (System Recovery DVD) and close.  I reboot and it goes directly to the office. I hear the whirring disc, but nothing happens.

  I go to the control panel > Recovery > advanced retrieval methods. I click on restart, and it loads files and then says DVD set, which I do. He told me that he does not recognize the installation disc.

  I googled this problem and found a poster on CNET that had the same problem as I do. Also, I can't do a system restore.  My problem is the same as this poster on CNET.  I can read DVDs and CDs.  Those that work very well.

  http://forums.CNET.com/7723-19411_102-568059/Windows-7-installation-disc-not-recognized/

  The files are on the DVD, because I see them.

  I don't know what to do. Should I send my PC back? Can I do to solve this problem?

  Thanks in advance.

  pen

  Hello:

  With recovery disc 1 into the DVD drive, restart the computer and at the beginning of the HP welcome screen, press the ESC key to display a menu of options.

  Select the F9 boot menu option.

  Select the DVD drive on the list of bootable devices, and press the Enter key.

  Watch the screen for additional instructions.

• MacBook does not recognize the SSD.

  Hello

  I would like to replace my HDD on my MacBookPro (13 "/ Mid 2010/ElCapitan") with an SSD. I bought a SanDisk card Ultra II 480 GB SSD and SATA to USB cable (this:http://www.ebay.co.uk/itm/251800670431?_trksid=p2057872.m2749.l2649&ssPageName=S % 3AMEBIDX % 3AIT TRK).

  I wanted to connect the SSD drive, format, make a copy of my HDD with SuperDuper! and change the part. But seems that my MBP does not recognize the SSD! I can't see it in disk utility, or in the office.

  What I am doing wrong?

  Thanks in advance.

  How have you plugged the SSD drive?  It is installed internally or externally via USB?

  Ciao.

• Canon 60 d does not recognize the 430ex II flash. Any suggestions?

  Canon 60 d does not recognize the 430ex II flash. On the menu screen, it says that flash is where not compatible.

  Any suggestions? Books or guides recommended?

  Thank you

  A few...

  I hope that you have verified that the flash lights up completely and you get the red light showing that it is ready to fire.

  On your system menu 60 d, if you find the "Flash control" option, you can ensure that you have not set the external speedlite to 'disable' - although I think in this mode, you wouldn't get the message you describe.  that is, I doubt it's, but you can double check.

  A more common reason for the failure is that the flash of the camera can perfectly communicate with flash.  This is usually due to a bad connection in the 'foot' of the lightning.

  The flash must be in place in the rails of the claw.  Make sure that the lock is released, fully slide the flash into the rails of the hoof, stop.  Engage the locking of the foot, so we got him firmly (it will slide to the right and then click sur-pour-snap (you must press the button to release the locking lever).)  This is not * only * snug foot... He also puts a tiny metal pin locking in a small hole in the claw so that flash can't get out.

  At this point, the "foot" of the flash is actually the "ground" connection and he is in contact with the metal rails of the claw AND the five contacts on the foot must be in contact with the camera.

  This means there is nothing wrong with the flash - and there could be something wrong with her.   So if you are convinced you fully secures the flash, then remove the flash and inspect the "foot" on the flash.

  The metal plate on the bottom of the flash must be strong... If you use your fingers and try to move it (do not use a heavy force... we do not break - just firmly grasp and see if he's going to move at all) it should not move.  If it does not move that this means that the foot is loose and is not attached to the body of the flash (there are four very small screws which hold it firmly, but they are accessible from the inside of the flash.

  Next, inspect the 5 metal pins on the bottom of the flash.  Each of these areas is spring loaded so that they will stand against the 5 points of contact in the camera shoe.  I sometimes saw a performance of something (for example, a bit of sand) getting stuck and 'jam' a PIN so that she she brings more contact with the contact on the hoof.  If you view the foot of the flash of an edge - on view, all the pins it is back to the same height.  If one of them is lower than the rest... indented it is blocked.

  The 430EX II has a solid reputation as a flash work horse.  It tends to be among the most reliable flashing on failures is rare.

  It is also possible that the problem is in the camera.  A simple test of this is to try an another speedlite (if you have one, or if you have a friend who has a).  If it's your speedlite, and it is under warranty, then it is probably a simple remedy of service Canon.

  If the flash is not under warranty and that the problem is with the hot-shoe is is not solid, it is often an easy repair.  If a foot have been irreparably damaged, the entire foot can be replaced (everything is a module) and it is an easy and I think a little low cost repair.

• Aspire One d255 does not recognize the usb connected external ssd drive

  I want to replace the original HDD 160 GB with a 120 GB Samsung ssd 750 evo but bios and win 10 does not recognize the ssd drive as an external drive connected via a usb connection, so I couldn't create an image of my internal hard drive.  Is there a way to clone my hard drive SSD, so I can exchange the disc later?  I need to update the bios, install a missing driver, etc. ?

  I used two different connections: one is a 2.5 "SATA case disc that I used with a disk 2.5" HARD and works very well with the HARD drive and the other is SATA/IDE connector combination with cables for SATA and power and none of these works.  I read in another forum during my research that the Aspire One d255 doesn't recognize any external SSD connected through a USB either.  Since my netbook has no data, and I had just a pure 10 Windows installed on his drive HARD internal, I removed the 160 GB HARD drive and replaced by a 120 GB SSD and installed another Windows own 10.  It worked and my system boots now in less than 20 seconds.   We can close this thread now since I now have a faster machine fully function.  Thank you!

• New installation of XP PRO sp3 does not recognize the 500 GB HD

  OK, here are the details:

  System: Computer PORTABLE of Acer Aspire 1700 Pent4, 2 GB of RAM, 80GB (3.5 "full-size, trainee) IDE HD [this is the original HD on this laptop of size important which is designed to use disks 3.5" hard].

  Initial situation: Windows XP Pro (SP3 integrated) installed on HDD of 80 GB and works without poblems. BIOS does NOT show the ability of the intern HD in the BIOS screen. BIOS reports only the model and the serial number of the HD, and there is no options to specify the HD type/format (e.g., MLA, etc.)

  Available: Win XP Pro bootable CD slipstreamed with SP3; It is tested and verified work well to install PC or laptop!

  When running XP Pro on a partition internal 80 GB HD, and when I join a brand new WD 500 GB IDE HD via USB, HD is recognized correctly. I can partition and copy data on the HD 500 GB with no problems!

  When I replaced the old 80 GB HD with the new HD 500 GB HD interning on the laptop, I have the following problems:

  1. I can NOT boot into Windows XP Pro (SP3) which was Ghost on the HD 500 GB of the old 80 GB portable HD it recharges, and if I try the console recovery or secure boot, then the laptop restarts also.
  1B. I have Ghost xp partition to 80 GB HD to a piece of spare HD (40 GB) and replaced the 80 GB with the 40 GB HD and was able to start the laptop without problem. So the problem is NOT related ghost!

  2. I can't perform a clean install of Windows XP Pro (SP3 integrated) because Windows XP Setup recognizes the HD 500 GB GB 131 HD. Therefore, the remaining capacity is not recognized.

  3. I can NOT perform the installation of Windows XP pro (SP3 integrated), even if I have previously partition new HD 500 GB by attaching it to a free desktop PC and use Partition Magic, partitioner of Paragon Disk or other partitioning tools. After partitioning prior, when the 500 GB HD is installed on the laptop (as a trainee HD), then win xp installation lists quality HD of GB 131 and lists the existing partitions as corrupt!

  4. Curiously, if I use Knoppix, Debian, Ubuntu or linux boot CD Mint and start the laptop computer with one of these linux distributions, then the linux installer recognize the HD properly during the phase of recognition of material and later during the phase partitioning HD, the linux system to report a full capacity of 500 GB available for partitioning. In addition, when there are partitions, partitioning linux program then lists these partitions properly as well!

  Considering the 4 points and especially MS Windows XP PRO (integrated with SP3, which should recognize HD with sizes exceeding 137 GB limit - from MS says you must be at least XP SP1 to overcome the size 137 GB limit - and that the different distributions of linux can see the full-size HD 500 GB with no problems) which is exactly the problem with Win XP? Why it does not recognize the full capacity? And how to win xp recognizes a 500 GB capacity, if the new HD is attached to the laptop via USB as an external drive when running XP PRO (SP3) of the 80 GB internal HD?

  so... Can anyone sheds light on the issue with Win XP Pro installation on HD 500 GB IDE?

  Nicely,

  LO

  Hi Palcouk and Doc,

  I think that's the final answer!

  Although, there is a mixture of simple to complex responses to the problem at hand, what it all comes down is that there is a significant difference between the installation of Windows XP and Linux installer program. The XP installation program needs help from the BIOS to deal with HD, and if the BIOS does not support, XP not has no facility to remedy the situation. OTOH, most of Linux new kernels rely on the BIOS for a limited number of extended, but communicate directly with the hardware, in this case, with the HD and therefore manages the material accordingly.

  It seems among users of dual-booting (win/linux) using old PCs, it is a matter of very pretty. What they end up doing is using the first 137 GB that is seen by the BIOS without problem for XP (either as a single partition or divided into several partitions), and the rest of the space is used for Linux because linux has no problem.

  I guess that it really nails the problem with my laptop to a BIOS NON-lba-48-bit!

  Then close this thread as answered or matter who has more to say about this?

  LO

  P.S.: It was very nice meeting you fellows and appreciate all the help and tech expertise.

• CD/DVD does not recognize the drive.

  CD/DVD does not recognize the drive.  Error message-"Insert a disk." "" "Insert a disk in the drive (E or F, depending on whether one in use).  I bought a DVD/CD thought exteranl today that might work.  Same error message with the external dvd/cd.  Can hear the disc turning when it is inserted during a short period of time, maybe 20 seconds, then it stops.  Sometimes, the disc is ejected when the error message appears, sometimes not.  Same results even with blank CDs.

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• my pc does not recognize the cd drive. I tried restoring the system without success.

  Windows does not recognize the cd drive

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• W7 Device Manager does not recognize the Intel AMT devices

  Please help: where can I find - how to install the latest drivers Intel AMT for Windows 7.

  Hello

  Thank you for the question to Microsoft Community. I'll give my best to help you.

  From your problem description, I understand that the Device Manager does not recognize the Intel AMT devices

  What is the brand and model of the computer?

  Check out these links and see if they help.

  Computers that use Intel's vPro technology can have devices that are not recognized in Windows 7 Device Manager

  http://support.Microsoft.com/kb/976728

  Clean installation WARNING: Back up your files before you begin reinstalling Windows, even if you're reinstalling Windows on a hard disk partition. A clean installation replaces the current version of Windows and all personal files.

  If your motherboard supports AMT technology, you can download, install the drivers from this link.

  AMT: Intel® AMT Driver for Intel® motherboards

  http://Downloadcenter.Intel.com/Detail_Desc.aspx?&DwnldID=16936

  Note: This download is valid for the products listed below.

  Intel® card mother DB43LD

  Intel® card mother DQ43AP

  Intel® card mother DQ45CB

  Intel® card mother DQ45EK

  If the problem persists, I suggest you to contact Intel support. http://communities.Intel.com/Community/Tech