Similar Questions

• Physical serial ports are supported in ESXi?

  Physical serial ports are supported in ESXi?  I install Windows 2008 SBS on a HP Proliant ML350 G6 ESXi (version of stick USB HP) running. The server comes with a serial port on board.  I was hoping that connect an external modem and expose it to the virtual server, Windows SBS 2008 to serve as a network fax.  Is this possible? Alternatives if not supported?

  It would be a no.

  There are TCP/IP USB devices, do not know if there are similar devices for the series, but NO physical devices, sound cards, usb, parallel, series can be transmitted to a virtual machine.  That's because ESX uses vmotion, and it was designed to let the virtual machine move between machines, so allowing physical connections so would interfere with this operation.

  http://www.tacticalsoftware.com/products/dialoutez.htm

  However, who should be a solution for you.

• LabVIEW Serial port wait event with Serial Termchar

  Hello world!

  I'm quite new with LabVIEW and I'm having some trouble trying to communicate using the serial port.

  I'm trying to detect a data frame with an 'X' as the terminal character sent to the serial port.

  The problem is that with the VI attached on this post I am not being able to detect the chariot of the term series.

  I tried to make some changes to fix this, but I can't.

  In VI, I used a function of Type Cast when I was using the wrong ASCII for 'X' value, but it still the same.

  Can anyone help with this?

  Thank you!

  Best regards

  Omar

  This will work only if your message can never be more than 8 characters including the character. term set this value to 1000 or something that is guaranteed to be always bigger than the size of your message and all should be good.

• Audio support two-way with PCoIP?

  I am recording the sound with an analog headphone/microphone plugged into a XP machine and connection to a VM XP via VMWare 4.0 build 233023.

  Sound recording is grayed out.

  Does anyone know if audio two-way is supposed to be supported with PCoIP for Windows or Linux?

  Thank you

  Hello Romatlo, bidirectional audio not supported yet... will be in a

  upcoming version.

• Time GPS, Position, Velocity.vi - error-1073807360 reading was held at node (arg 1) .vi property VISA set up a Serial Port (Instr)

  We receive information such as the Latitude and Longitude of a receiver Garmin GPS18xLVC via a serial port on our PC using LabView 7.1.  Successfully, I connected the GPS on the serial port and tested with HyperTerminal.  I tried reading GPS time, Position, Velocity.vi several times and still receive the following error message: error 1073807360 has occurred to the property node (arg 1) visa configure a Serial Port (Instr) .vi.  I think it has something to with the configuration of the VISA series under vi.  Any suggestions would be greatly appreciated.

  Thank you

  I understood the question, that I had with the time reading the GPS, the Position, the Velocity.vi.  The vi. "do not open" port com automatically and so I had to modify the NMEA GPS Subvi reading to first open the port (VISA open command) and then continue with other operations.  Once I did this it started to work very well.  I don't understand why this feature has been left out because it won't work without it.  I tested the code with a receiver Garmin 18xlvc and it seems to work fine.

• Limited virtual serial ports

  Hello

  Is it possible to add more than 4 virtual serial ports to VM?

  P.S. 4 virtual serial ports works only with the EFI firmware. With BIOS firmware only works under MS Windows. Is this normal?

  Hello

  The maximum is four - http://www.vmware.com/pdf/vsphere5/r50/vsphere-50-configuration-maximums.pdf

• Portege M200: serial port does not work with port replicator

  Hello
  I have a Tablet m200 and the top mentioned dock/replication PA3314-1PRP port.
  As the M200 has no serial port (rs232), I want to use the one on the docking station, but it is not recognized as a device on my tablet.

  Thew network connections and usb ports all work fine and the lpt port is shown in Device Manager. I have restored the Tablet and it still does not recognize the serial port.
  How can I get this port recognized so that I can use it.

  Thank you very much
  Lee

  Hello Lee

  I just, I can confirm that when you use the Replicator port advanced III with Portege M200 several ports do not work. Problem is that Portege M200 does not support these interfaces.

  This is a technical limitation and the port of mouse PS/2 port keyboard PS/2, serial port, I.Link (Firewire) port and DVI port will not be supported when Portege M200 is anchored on the Advanced Port Replicator III. :(

• Several Modbus with shared serial port

  I know that Lookout lets do you cool things like have several protocols series that share the same serial port hardware.

  I asked where I might like Lookout to simulate a network of Modbus Devices for some tests. In this case, I want to implement multiple Modbus slave, all with different node addresses Modbus objects and have all listen to the same serial port. Would this be possible? Each received Modbus message will include the number of slaves in there. Multiple objects can listen on port and only the selected one respond?

  Thank you

  Max

  Yes, slave modbus Lookout can work this way.

  But the ethernet mode does not support.

• the NI 9871 serial ports appear also in MAX with built-in serial ports of the target - under devices and Interfaces IS NOT? NO NEITHER 9871 (Scan Interface)?

  Hi - Have cRIO

  Can someone help me get the NI 9871 (Scan Interface) work?  My two 9477 and two 9425 and 9403, function with the scanning Interface.  In MAX > software > NOR-Serial RT 3.82 > NOR-Serial 9870 and Scan Engine Suport 3.8.2 9871 BUT NOT == MAX > devices and Interfaces > series & parallel = number of Ports Com for 9871 listed?   Project, 4-port RS-485 NI 9871 is in slot1?  Any help appreciated thanks

  the serial ports on the NI 9871 also appear in MAX with serial ports integrated target under devices and Interfaces

   

  NEITHER 9871 (Scan Interface)

  I left the Slot 1 Slot 8 9871 Know works and MAX displays 4 COM ports.  Something is misconfigured in Slot1?

  Solved!

  Thank you

• reading photoplethysmograph waveform with serial port on PC using Labview

  Hello world

  I'm gaining time real Photoplethysmography waveform of serial port using Labview.I have managed to acquire data from serial port by using the following features:

  -Baud rate: 38400

  -data bits: 8

  -stopbit: 1

   

  -No parity bit

  -Time delay before reading the serial port: 10 ms (according to what was written in the manual that every 10 ms there is a frame in serial port)

  After the reading string will be converted to byte array to be able to extract the bytes associated with waveform (1 & 2 bytes in a frame) even for SOP2 (6 & 7)

  (what is read in serial port is in decimal and must be converted to hexadecimal based on what made the software of prodeuct for some result.that in the waveform properties, I chose the hexadecimal representation)

  Then, as mentioned in the manual, I associate these two values to draw the waveform.

  Although I used the filter band digital waveform of pulse but not significant pass that was seen (cutofffrequeny:10 high low cut-off frequency: 0.5).

  I have attached my program and result in front of Panel and manual for the sensor. The result is still far from what is supposed to be. I was wondering if you could help me and let me know your opinion on the program and the protocol used. I have to get the result as soon as possible. Please let me know if you need more information.

  Kind regards

  
  

• Communication Serial Port with PIC

  Dear all.

  I am interfacing the labVIEW to an eeprom controller PIC, where I need to input data user to store in a location memory EEPROM, according to my condition that I've done programming the pic and it works very well with hyperterminal, at the same time I need to do with a labVIEW using communication serial port VISA , but when I did I receive a warning in 1073676294 that cannot be ignored, but I am not able to write user data to EEPROM by labview but I can do it to hyperterminal, please someone help me on this.

  Charron a G

  I was interfacing to pictures for a while, and the example that you have to build from was the same that I used. First, move the initialization OF THE outside of the loop. No need to re-initialization of the COMM PORT every 750ms.  Inside the code example, there is an expectation of 500ms between WRITING and READING (it is hardcoded for now, you brought it out on the ICON).  So time total is 750ms loop over the 500ms wait (more traffic comms), FYI.

  You do not use a return of ramasseherbe (13) or a NEWLINE (10) as a dismissal. You use a SO (14). Unless you're on a triggering a 14 ASCII in the PIC, the PIC will never see the "end of the chain of command" to analyze out. I have attached a good routine of init (IMO) I re - use on all my PIC projects, take a look.

  I use compilers Mikroelectronica MikroCPRO and displayed a complete interface of the UART (triggers on a CR (13)) on their site LIBSTOCK if you want to take a look at the side of the PHOTO of my work.

  http://www.libstock.com/projects/view/250/RS232-interrupt-driven-command-based-interface

  Steve

• Serial port with LabView

  Hi all

  I have some kind of project as a proximity matrix. Pretty much looks like 16 LED panels in the config of 4 by 4.

  I need to create a GUI that can show what I physically see. IE: I have a block of LED that shows me the intensity or brightness of the LED is full or half of the intensity and I want that same value or data appear on the screen with a delay of almost nothing.

  I use a PIC16f73 with IrDA sensors. The sensor sends the value of the ADC to the PIC and then send this value to the PWM port that controls the LED then this same numerical value, it will go to the PC via master/slave SPI communication.

  Let's say, I have the entry value of the slave 11001100 and past by the master and then go to the computer via a SERIAL port, I want the lu GUI only and interprets this as a specific value and modify the intensity of this block on the GUI.

  How can I do? I already attracts 16 Blocks (LEDs) using the LabView, but I don't know what to do to perform playback of the Serial Port and then interpret that and make a table of the eye and the screen will change the color from black to white depending on the intensity.

  Can someone help me with this problem please.

  
  

• Communication with Serial Port

  Hello

  Hi I have a request that I should communicate with serial port...

  Its works perfectly if gives you all parameters to com as constants (pls hav a look @ codea).

  But I want to read the port number and baud RRSP file text. When I changed the encoding in serial number

  setting, I was not able to find the number rate.it and port baud displayed as the size of memory buffer. I think that the way I connected the baud rate and port number to the clusture may be a problem (pls see codeb). How can I solve this problem?

  Thanks in advance...

  Again, the point of connection to the Central Terminal is not not to define the values contained in the cluster - just the logical structure of the cluster. The data that appears in the cluster from the budler will reflect the data that you read from the file. Try it.

  Mike...

• cann't communcate with my serial port device?

  I connect controller E-753 of the Instrument of Physik for the command from step of piezo nanopositioning via RS232 serial port, when I communicate with the device using the interface that it comes with it's ok, but I could not able to set it up by the MAE or labview, when I tried to use the test panel Visa I always get return BFFF0015 status.

  Please all help

  Thank you

  Aneece

  Thanks, it's resolved, it was due to a frame, now, I tried to write and read using labview, so that I could not manage to connect, for the resource of visa I wire only the port # COM1, will I have to do the series in order to get. Please advice

• The creation of a virtual serial Port for Windows 7 hot Synch an old Palm Treo 700 p with Palm Desktop by Bluetooth

  I am trying to synch (HotSync) an old Palm Treo 700 p with Windows 7 by Bluetooth and the Palm Treo 700 p tells me that I need to create a virtual serial port on the Bluetooth on my PC to synchronize.  I can't understand how to create this port in Windows 7.   Can someone help me?

  Try this link to TechNet for this solution.

  https://social.technet.Microsoft.com/search/en-us?query=Windows%207%20create%20A%20Virtual%20Serial%20Port&AC=5