Tecra 520 cdt - Manual of use of need

Similar Questions

• Battery Tecra 520 CDT

  Now I have two computers TECRA 520 CDT that will not charge the battery.

  The batteries are in good condition (a new) and can be loaded on another machine of CDT 520 by using the same charger, then the 'dead' machine will work and the charger to maintain the battery.

  This problem can be repaired and if so by whom?

  Hello

  > This problem can be repaired and if so by whom
  If you are sure that this problem is not related to the defective battery, then it must be a problem of laptop computer at 100%.
  Who knows why the battery may not charge maybe there is something wrong with the motherboard or only some pins of the battery are not connected correctly.

  What is the battery LED lights up when you insert the battery into the device and unplug the AC adapter?

  If not then that would mean that the battery is not recognized and this would mean that there is something wrong with the laptop
  In this case, the machine must be checked by a technician for laptop
  You should contact the ASP from Toshiba (certified partner)

• RAM for Tecra 740 CDT

  I just bought an old laptop TECRA 740 CDT on eBay to travel without fear. Aries is in fact of 64 or 80 MB (to be confirmed) and I want to bring to 144 MB (at most, I think).

  What kind of RAM do I use (SIMM?) and it's easy to do it yourself? Thanks for any tip and the thing!

  Hello

  I found the info that you need module memory 128 MB of the PA2046U. Check it out!

  By the way: I can confirm that 144 MB of RAM is the max, you can use on this good old classic.

• Tecra 740 cdt - how to access BIOS?

  Hello
  I have an old Tecra 740 cdt no hard drive and a hard drive empty.
  I wonder how to access BIOS so I could change the boot priority to boot from a bootable CD.
  Navigating on this forum I found a few keystrokes as F2, F8 and so on, but it did not work for me.
  Can anyone help?

  TIA

  Have you tried to click on the ESC then F1 immediately after switching on the laptop?
  As far as I know it should work on all laptops with BIOS Toshiba

• Need to Tecra M10 USB formatting before use

  Hi all

  It is a problem, I was confronted during about one month.
  I already asked for help in support of Microsoft and I managed the problem circumstance, unfortunately without being able to solve it.
  The problem is the following:

  Whenever I plug in an external hard drive via USB I wonder to format it before using it. This of course I do not. This problem appeared all of a sudden, before everything worked perfectly.

  My external hard drives work perfectly, in other forums, namely other laptops.

  In addition, if I reboot Windows 7 in the 'safe mode' can I connect external hard drives via USB without problems. It seems that it is something that I had recently which is contradictory to my external hard drives.

  What is an update from Toshiba? You have an idea about the things I could try to locate the problem?

  Thank you in advance.
  See you soon
  Andrea

  Hi Andrea

  You have portable external hard drive or Toshiba Toshiba? I ask this question because you ask for Toshiba update.

• Tecra M2 - adapter that I use?

  Hello

  I bought an old Tecra M2 but without the AC adapter.

  I found no Reference Toshiba in he owner manual, or in the support section (all kinds of Tecra are listed, but not the Tecra M2!)

  I have an old Toshiba Satelitte pro with a power adapter (15V 3A output) Toshiba. If it works? Bad tutored?

  Some people have told me it would be necessary to have a power supply with an output of 15V 5a. Is this good?

  What do you think?

  Thank you

  Hello

  Your Tecra M2 needs adapter that support these specifications;
  15V 5A 75W, 100-240 V
  The PA3283U-1ACA AC adapter would be compatible.

  Google for this number and you will find online offers.

• Tecra M10 cannot install OS using disc SSD Kingston

  Hi all.

  I am a computer tech and can usually find a way to fix something myself, (rock Google!).

  But recently I had a Kingston SSDNOW 64 GB drive and decided to install in my Tecra M10 age of 12 months. 4 weeks ago I had a full head of hair, now I am completely bald.

  The drive is recognized in the BIOS, but whenever I try to install Windows on it, I get nothing. I tried the recovery DVDs XP, recovery DVDs Vista The, the "free" upgrade Windows 7 recovery DVD, and a DVD Vista & Windows 7 retail. I can't drive to be recognized to install Windows.

  I can copy the existing disk image, but it starts the splash screens and blue. Normally I think that driver RAID or hard disk controller, but Kingston assures me that there is no requirement on the one hand, (and a standard SATA drive does not require a, I tried).

  I checked and installed the latest version of the BIOS for laptop. There is no update available for the SSD firmware. So I find myself with a laptop that always uses a slow, (relatively) hard drive and a very pretty silver rectangular Clipboard.

  Can anyone think of anything whatsoever that I missed. Anyone working for Toshiba can tell me if there is a BIOS update for this problem (I search the forum and found many people who are struggling for SSDS working in Toshiba laptops)?

  The sad thing is that the former other laptop I got for my son accepts the player and works fine!
  I had many prefer to buy Toshiba, but I want SSD technology rather sooner than later, and if Toshiba does not go to support, I might have to change of Lenovo or Acer.

  Rob.

  > Normally I would RAID driver or controller hard drive, but Kingston assures me that there is no requirement on the one hand, (and a standard SATA drive does not require one, I tried).

  I think you have misunderstood something the SSD drive does not need SATA drivers BUT the fact the OS (Win XP, Vista or Win 7)!

  The SATA drivers are needed to recognize the HDD/SSD under Windows OS.
  New generation of portable supports the new SATA controllers that require SATA drivers.

  You will find on the European driver Toshiba Intel Storage Manager page

  Intel Storage Manager contains the SATA drivers that are required to install the OS.

  Welcome them

• Tecra S10-11 - can I use a labelflash DVD disc?

  I have a laptop Tecra S10 - 11A.
  I would like to know if it is possible to change my internal DVD drive to another which has a capacity of 'labelflash '.

  Today, Toshiba sell laptops of the Satellite series with this kind of DVD.

  It ' possible to change my drive integrated with a Toshiba product or I have to use an external?

  Thanks in advance!

  Well, you must use a CD/DVD drive with the master/slave/c-salt settings compatible.
  The settings are controlled by ODD firmware.
  According to the user's manual these discs are supported;
  -DVD-ROM TEAC D-28
  -TEAC dinner Multi with DL recording DV-W28S
  -Panasonic DVD Multi DL recording UJ890
  -Hitachi LG DVD dinner Multi DL GT20N

  I don't know if one of these m readers would have supported the lableflash feature but usually you can order all the compatible parts of the ASP from Toshiba and maybe other drives with labelflash functionality would be compatible with your laptop

• Tecra S3: GeForce Go 6600 driver update needed!

  Hello world

  I'm looking for hours for a new driver for my GeForce card, unfortunately nVidia nothingness or Toshiba it provide on their download section.

  My current driver is version 7.8.1.7 of 26 July 2005.

  I already tried an automatic update and
  the laptop program: nVIDIA ForceWare X 156.83 for Windows XP / 2K 32 bit

  Any help is welcome

  Best regards
  Muggle

  Hello Muggles

  Maybe a stupid question, but I would like to know why you need this update. In my opinion, Tecra S3 is not game machine, and I think with driver existing Toshiba, you can use this laptop for all standard graphics operations.

  Do you use a 3D graphics application?

• Tecra 500 CDT does not start. Please help with CP

  Hi all

  I have an old Tecra CDT of 500 which, up until yesterday, worked fabulously. Now for some reason it starts at all. No matter how long you push the Start button on the side, he shows no signs of life at all. It's been hot here lately so I wonder if it's suffering "heat exhaustion! Seriously, clues as to what could have caused this problem and how to overcome it would be greatly appreciated. It has been used much more recent than usual and for hours. Is this likely to have helped him give up the ghost?

  I hope someone out there can help.

  Thank you
  Dynamo-dom

  Hi Dominic,

  It would seem that your laptop has developed a hardware failure, either with the current power switch the PSU internally. I think that your only action now is to contact a service partner and ask them a price that it be repaired.

  Good luck

• set a path to the report manually by using < clientfiledir >

  Hi all

  I'm pretty new to teststand so please forgive me if this is an easy question.

  BACKGROUND

  I'm running a sequence (TestGroup) that contains several sequences (tests) that work as a new execution.  It allows me to produce an individual report for each test (the top-level sequence produces a summary report only).

  QUESTION

  I want each of the reports to be stored in a single folder. I have setup report options to calculate the path of the report by using the following expression "\\Reports\\\\SummaryReport [] []".".

  This works very well for the top level, but that this also applies to the subsequences path is recalculated and is different from that of the upper level.

  CURRENT SOLUTION

  I'm currently moving the report path as a parameter to test sequences, but I find the value of the macro (from the sequence of high level) to build the report path.  Can someone tell me how to get this?

  Another solution is for me to take the path of the current report and the name of the file of this band.  It's a better solution?

  Any help would be great.  Thank you

  G

  Hi Jack,

  I use a whole test sequence (seq) group and a running each of my tests as a new execution.  This means that I can apply a different template to each test (which is needed to support the old style of the previous tests developed by my client) and produce a report of individual test for each test.  Then I clear the list of results when the report was drafted and replace it with a link to the report for the test (I hope that this reduces the risk of running out of memory on long series of tests).

  Each of my 'tests' is indeed a full sequence.

  I was hoping to use something similar to macros to move the report path to each of my tests (or model for the test), but have not been able to find these values anywhere in the report options window.  Ultimately I have to now take the string generated for high level sequence 'group' and make a formatted string and then pass it as a parameter testing (an another headache that had some problems).

  I'm not really a fan of this and think it should be possibel to configure the report options different for each model, that I had to do it manually by hardcoding stuff like path .xsl etc names.

  can someone tellme if it seems like the right approach?

  G

• Corrupted Movie Maker in Windows 7 32 bit Home Premium, associated with error, and I can't find the files manually to use, uninstall or remove.

  I had Windows Live Essentials Movie Maker installed on my system at some point, but then I continued to see live pop up in the Task Manager and no matter how many times I killed him, he always came back even though I was not using the program, so I uninstalled Windows Essentials 2012 to stop this, and it kept popping up , so I went into the system and manually delete anything with Windows Live in the name of via Explorer and then a bit in the registry. He solved the problem, however, now I would once again use Movie Maker, and then I'm gone on the download site to download Movie Maker, thinking this would reinstall it and I'd be set (other than to have to look at consume resources when closed). I tried to get just Movie Maker, but the windows site told me that I had already installed (I can't find something that he mentions just anywhere), so I found another download Movie Maker, an earlier version, which has installed, but did not have the features that I need, so I uninstalled it, so I thought I would setup the whole Windows/Windows Live Essentials 2012 thinking that can replace bad Windows files detected as a facility, but he did not, he just installed anything ELSE in the software suite and I still haven't Movie Maker. He gave me this error (error: 0 x 80280007) when I tried to redo the installation:

  Very well, dandy, I'm happy to do, except that I can't FIND it to uninstall, and it is not in programs and features (uninstall or change a program list). Thus, two options. can someone tell me how to

  1. Movie Maker WORK, tell me where it is and how to start (there is not in Program Files at all).

  2 tell me how to remove completely ANY TRACE of all Windows Live Essentials 2012 so I can do a fresh install of it that works.

  I went to the support conversation Windows and asked how to remove traces of Movie maker, and the tech told me to do:

  del \"%SystemRoot%\system32\dllcache\wmm.dll\".
  del \"%SystemRoot%\system32\dllcache\moviemk.exe\".
  del \"%ProgramFiles%\Movie Maker\. \ »
  rmdir /s \"%ProgramFiles%\Movie Maker\.

  But the thing is, none of those that exist to remove, and so I don't think he really UNDERSTOOD what is my problem (more, it hung up). I didn't run them, it seemed useless.

  Alternative: Point Me in the direction of another free software that works as a Movie Maker program. I don't like that makes the software, I just need to put a bunch of short video clips together in a longer video.

  In case anyone cares, it's corrected now. I had to do a repair installation to fix but. Finally, here's what worked:
  https://www.WinHelp.us/non-destructive-reinstall-of-Windows-7.html

• I downloaded presets and somehow deleted the 'DEVELOPING' tap water  He cannot change it manually or use the presets?  How should I do?

  wwhen download presets, I must have misplaced the file "develop."  I can't edit photos using presets or manually.  Don't know what I did?  It appears "the file is not found" on my screen?

  Hi Sarar,

  It seems that the file you were working in Lightroom has been moved or deleted.

  If you need to reconnect the images in Lightroom since the library Module.

  Please visit the following link: Adobe Lightroom - find folders and files moved or missing

  Let me know if it helps.

  Kind regards

  Tanuj

• bought used iphone need help to activate without sim

  I bought a used iPhone 4 trying to activate, but guard saying need sim, I don't have that I just want to start so that my son can download him a few games and then I can buy a phone plan and SIM at a later date... Help

  You must obtain cellular service from a local supplier who will provide the SIM card. Note that if the device is locked otherwise you may not be not able to use it at all.

  It requires the Apple ID and password from the previous owner. If you don't have it and can't get it, then the device is useless to you. Return it for a refund, if you can, or take it to an Apple store for an Exchange, I hope they will help you.

  Find my iPhone Activation Lock

  Check in the future first before you buy second hand: How to check for Activation lock before buying a second hand iPhone.

• Tecra A8 PTA83A - Vista 32 bit drivers needed

  Hello

  I'll try to find the drivers (Vista 32 bit) for this computer laptop pta83a - 04g 012.

  However, I can not even find the laptop on the Australian site. In fact I can't find anywhere what "A8" laptops at all.

  http://www.MyToshiba.com.au/support/download

  Can someone help me please.

  I also checked some other sites Toshiba from different countries without result.

  I wish there was an option to check through all countries, at the same time.

  Kind regards
  Paul

  Hmm... I'm not sure why this Tecra series is not listed on the page of the Australian driver Toshiba but same model Tecra A8E PTA83 is released in Europe also.

  

  You can download and use the drivers for your laptop that appear on the page of the European driver Toshiba
  http://www.Toshiba.EU/innovation/Dow...jsp?service=EU

  The drivers are fully compatible