Tecra 8000: incorrect checksum error

Similar Questions

• Satellite Pro U200 - incorrect checksum error (ROM (data block))

  Hello when I run my Satellite Pro U200 Toahiba
  I have an error

  Incorrect checksum (ROM (data block))
  PRESS ANY KEY TO CONTINUES.

  Pleas Help

  The most common cause for the mistakes of "Bad Checksum" is the CMOS battery on the motherboard failure.
  The battery may be empty or could have been dead. But it's really not easy to say exactly what's wrong!

  Therefore, I recommend first to access the BIOS and set it to default settings. Don t forget to save the changes.
  More you must connect to the AC adapter and should leave it plugged during on 24 hours to recharge the battery CMOS.

  Maybe it helps to get rid of this error message.
  If it doesn't help, then you should contact a technician for laptop!

• AcrobatPro_11_Web_W incorrect checksum error message?

  I am trying to download a trial version of Acrobat Pro XI and continue to receive the following error message:

  Invalid checksum AcrobatPro_11_Web_W

  Any ideas?

  Hi miabea150,

  If you are running Snow Leopard or Lion OS X, go to disk-> preferences utility. Uncheck "verify checksums. Then try to install Acrobat 11.

  After you have installed successfully, please go back to disk-> the option preferences utility and recocher "verify checksums.

• Incorrect checksum error

  I tried 6 times to download the Web editing and design of the CS6... Downloads, it stops when you open the file zipped with an error "invalid checksum". I'm on a brand new imac 27 "Mt Lion installed. Help

  Use another browser like Firefox.

  Mylenium

• Checksum error message incorrect A250 aftetr Bios Update on Equium A100

  I received the message 'bad checksum A250' to restart after update Bios on Equium A100 - psaa4e Windows XP home sp3.

  Update 20070709121820 installed BIOS downloaded through this Web site.
  I installed directly from the downloaded file.
  System seems to not operate normally if have I messed up anything?

  Hello

  This message always appears during the clean boot procedure or it appeared only once?

  Generally 'bad checksum' error message if the CMOS battery does not work correctly.

  But I have no idea why you get this message after update BIOS... Anyway if the laptop works correctly after updating the BIOS then you should t be worried.

  See you soon

• Tecra 8000, linux & ethernet & pnp

  Hello

  I am trying to install Linux on a Toshiba Tecra 8000. The problem is with a chipset Realtek ethernet PCMCIA card (module: 8139too), which is recognized, but the network is unusable. I always get an error of SIOCSFFLAGS and assigned interruption is 0, which means that it has failed. I have read many times that I have to disable plug-and-play, but there is no choice when I start with a floppy and run the TSETUP. EXE. Y at - it an alternative to this? Do you have any other clues?

  Thanks, Thomas

  Hello

  Perhaps the following site will help you solve the problem.

  Here are 2 official linux Toshiba sites and there are also some tips.

  http://newsletter.toshiba-tro.de/main/index.html

  http://Linux.Toshiba-DME.co.jp/Linux/index.htm

  PS: You can also enter the BIOS if you press the ESC key immediately after lighting NB!

  Goodbye, Meier

• Tecra 8000: No memory available to connect with area map PC

  I have a Tecra 8000 running Win98 SE and use a card PCMCIA 3Com for my Internet connection. I was troubleshooting my computer on another issue and in the process disabled Cardbus PCMCIA Toshiba ToPIC controllers. After you have enabled these again once I am more able to communicate with the PC card and so unable to connect to the Internet.

  Card troubleshooting agent PC States: "Windows is not able to identify or use the inserted PC card device because there is no available memory area to connect with this device. You need to do an area memory available before this device can be used. Check the CONFIGURATION of your computer. A memory manager that is excluding the regions of superior memory between A000 and FFFF in the SYS file '.

  My Cardbus controllers are defined as follows:
  1 memory range - 0c 000000 - 0C000FFF
  2 memory range - 001000 0c - 0C001FFF

  My PC Card (PCMCIA) properties are as follows:
  Card services shared memory:
  Start 000c 0000
  End 00FFFFFF
  Length 00001000

  While the PC Card Modem is recognized at the Port, it can be communicated with and error message is shown as follows:

  ' Error 666: the modem is not plugged in or is out of service. "Connect a modem to your computer and try again.

  When I run the Diagnostics on the Modem does not respond to the exception of the following:

  "' Open Comm: cannot open port"

  Any help or advice will be appreciated.

  Have you tried to uninstall the Cardbus drivers? Not sure about the location in Win98 (in XP it is in Device Manager), go to "PCMCIA adapters" and uninstall all entries in controller.

  Reboot and Win98 will perform his routine "new hardware found". This is going to re - install drivers and with a bit of luck should solve your problem.

• Tecra 8000: monitor and the HARD disk does not work - does not start

  I have a laptop Toshiba Tecra 8000 given to me the year last by my uncle. I live in England, but it is and bought the PC in Italy. I do not know if this causes complications, but I thought it may be useful.

  Since I got it it occasionally did not display any image of all system startup, so if I have given some time and restarted it would start working again. Happening of bagan more frequently and now I can't make it work. I have conections and found that everything was in place. Then he doesn't seem to be turning on, however when I replaced the front LED cable seems to be turning on and although I couldn't hear much the CPU was luminous heat. I opened the drive and it gave once more, succeeded him and he still wouldn't start. I had purchased and replaced the screws on the heatsink around this area but I did not handle it with many other things.

  So now, I have a monitor that does not work and a gard drive that won't start... Any ideas?

  Thank you!

  Hello

  Could be either the card mother, CPU or ram. The processor when it goes bad or is not locked in place (have had this before, install the CPU but forgot to turn the lock, so he cannot move) the computer will act as its startup, don't give any error and stay on a black screen. Verify that the processor is locked in place. Then remove the ram and try a stick of RAM that runs on another computer. If you try the RAM and the processor do not always start, then chances are your motherboard is dead and must be replaced. Hope this helps and that solve you the problem.

• Tecra 8000/windows98se register

  I have a tecra 8000 which has a default intermittent starting
  When his absentees for awhile. Next time you start it has errors on the windows registry and stop to repair the registry, once it starts successfully, it is ok, including reboots, unless you leave for a few hours or overnight. Someone has an idea of what could be the cause

  Hello

  It is not easy to say but is obviously an entry in the registry is damaged and may not be readable or understandable to the OS. After that it must be written again. On this path, it is not possible to give you an answer why this happens. It is possible that some application that runs on your unit to this entry.

  Sorry but I can't give you more information about this

  Good bye

• Tecra 8000: Cannot start - Message "Insert disc in the drive system" lights

  I have a Tecra 8000, I've not used for about two months. Now when I try to start the "Disk system to insert in the drive" message on the display. I tried three disks in the system, but they have not been accepted and the same message appears. I visited in the 'setup' and changed priorities and tried to floppy, CD-ROM, HARD disk drive, and the same message every time. Is it possible that the internal battery "backup" is completely flat?

  Hello

  Well, I'm not sure about your suggestion of the bios battery. Usually, you will see an error massage low battery BIOS or CMOS battery low.
  Well, but if the battery is low, so all settings are disabled and the BIOS can't save the changes.
  It's not easy to say what the problem is. If there is something wrong with the material if you ask ASP for help.

• Photoshop-trial - incorrect checksum

  iMac Core 2 Duo 2.4 GHz

  OS X 10.6.8

  4 GB of ram

  > 900 GB of free

  I downloaded the trial 4 times now, different times of the day. Get the incorrect checksum after download. Disk utility can not verify with the CRC32 even exact on the last three files (I deleted the first). Same error every time:

  

  

  The CRC, looks like I have exactly the same file each time.

  I regularly download > 1 GB files every day, > 8 GB files per week (on another computer) and the checksums match. Should prove my connection ISP/Internet is not to blame, because it was suggested solution (use a different ISP). I could use this computer to download but it's Windows and I want the Mac version.

  IS THERE A DIRECT LINK TO DOWNLOAD THE TRIAL?

  I Reset Safari, I deleted the cache and ADA prefrences, I started cold, I save the file in different locations in my user folder, still get the same CRC every time.

  Jeff - Thanks for trying to help. I have all the step 1 no change in symptoms. I kept getting SAME CRC CHECKSUM (in disk utility) with each download:

  $68976E38, 811480 B $9 expected

  The solution that I couldn't find in the forums was to type this command in a Terminal:

  > com.apple.frameworks.diskimages: write skip - verify - bool YES

  This allowed me to mount the disk image and install Photoshop without a hitch.

  Thanks to Sumi in Live Chat for this command!

• Updating BIOS for Tecra 8000 without floppy

  I searched this forum a solution update the BIOS without a floppy drive. The only one i found was this thread [http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=66966&tstart=0], but there is no file .iso for the tecra 8000 series.
  is there a solution to get the new bios installed on my tecra 8000 without any floppy drive?

  I checked Toshiba BIOS download page on http://www.toshiba.eu/innovation/download_bios.jsp and TRAD BIOS version is proposed. This old Tecra is maybe 10 years and now, Toshiba has offered traditional update the BIOS only.

  Win versions are later available with latest Tecra 9000/9100.
  I'm sorry.

  Maybe stupid question now, but why do you need the BIOS update?

• Tecra 8000 - failure to CD-ROM - new installation disc?

  The CD-ROM drive in my Tecra 8000 has a defect. It attempts to load a CD-ROM, LED is flashing, it stops, and then the drive LED is lit.
  So I guess the drive is down.

  What kind of new CD-ROM is suitable for this laptop? Toshiba only original ones?

  Hello

  Wow, the Tecra 8000 series is really old. Do you use yet this laptop?
  It feels like the notebook would come from the stone age ;)

  However, I think that the CD/DVD drive supports * interface IDE but not all readers would be compatible due to master/slave/cable select settings

  It seems that the reader of DVD-ROM + Toshiba - SD-C2002 + would be compatible.
  Not sure if you'll be able to get this disc because of the age of the unit, but probably the authorized Toshiba maintainer in your country could provide some readers compatible optical disc

• Tecra 8000 and broadband connection

  Hi all

  I recently asked to watch Tecra 8000 a friends (PII 233) and give it a bit of an update... Don't know why the most I've ever done, is to add a few small components in my PC at home!

  My question is - is this possible for a connection broadband to be put in place - I looked all over the laptop, but don't find nothing which would suggest it is possible.
  (Also what other improvements should be can) watching us.

  Sorry for the noobness, but any help is greatly appreciated.

  Thank you

  Ben

  Wow this is really an oldie
  Broadband do you mean the LAN port?

  As far as I know that the Tecra 8000 was not equipped with LAN port.
  It s really amazing but it is a fact

  However, if you want to use LAN then I advise you to buy a PCMCIA (Cardbus 32-bit) LAN card that would be allows to connect the Tecra 8000 to LAN.

  See you soon

• Tecra 8000 - how to connect the HARD drive to another laptop?

  Hello, what kind of camera do I need to connect an old hard drive Tecra 8000 to a laptop from another production?

  I want to just transfer some data, but the connector on the Tecra ac no longer works.

  Hello!

  You can use a drive enclosure external DRIVE with USB port for this.
  The external HARD disk enclosure should be for 2.5 s HDD with IDE interface. All that s.

  Contact your local computer dealer. I'm sure they will have these cases.

  Good bye