Tecra A11 and BACK version of Symantec Ghost

Similar Questions

• Tecra A11 - 1F4 (PTSE0E-OM6052EN) which XP AHCI driver?

  I am trying to install the drivers for XP on a Tecra A11 AHCI;

  I have a ghost image that loads on this laptop in compatibility mode in the BIOS and I try to update the driver for the drive in AHCI controller, restart & change the disk to AHCI mode in the BIOS.

  That's what I usually do for HP laptops, we have, and it works most of the time.

  Storage power Toshiba drivers are in the form of an executable that will only work if you have AHCI enabled, how anyone runs in compatibility mode supposed to use these?
  They don't even extract driver files, you can use only the .cab files and an installer.

  I have listed in the device under IDE ATA/ATAPI controllers Manager;

  Intel (R) 5 Series/3400 Series Chipset Family 2 port Serial ATA Storage Controller - 3B2D
  Intel (R) 5 Series/3400 Series Chipset Family 4 port Serial ATA Storage Controller - 3B 28
  Primary IDE channel
  Primary IDE channel
  Secondary IDE channel
  Secondary IDE channel
  3 entries for Peter card reader &

  Intel drivers, I downloaded from-

  s http://downloadcenter.Intel.com/Confirm.aspx?httpDown=http://downloadmirror.Intel.com/21730/eng/f6flpy-x86.zip&lang=eng&DwnldID=21730&DownloadType=Driver & OSFullname = Windows + XP + *.

  .. .and it gives me the list of controllers to choose;

  Intel (R) 5 Series 4 Port SATA AHCI Controller
  Intel (R) 5 Series 6 Port SATA AHCI Controller
  Intel (R) 5 Series/3400 Series SATA AHCI Controller
  Intel (R) 7 Series Chipsets SATA AHCI Controller
  Intel (R) 7 series/C216 Chipset Family SATA AHCI Controller
  Intel (R) Desktop/Workstation/Server Express Chipset SATA AHCI Controller
  Intel(r) ICH10D / DO SATA AHCI Controller
  Intel(r) ICH10R SATA AHCI Controller
  Intel(r) ICH7M/MDH SATA AHCI Controller
  Intel(r) ICH9M - E / M SATA AHCI Controller
  Intel (R) Mobile Express Chipset SATA AHCI Controller

  The device ID of the controller (Intel (R) 5 Series/3400 Series Chipset Family 4 port Serial ATA Storage Controller - B 3, 28), I'm trying to install the drivers AHCI is;
  PCI\VEN_8086 & DEV_3B28 & SUBSYS_00011179 & REV_06\3 & 115 83659 & 0 & FA

  Please can someone tell me which of these to use with the above material?

  It takes me ages to build, install, bluescreen & rebuild to try again...

  Thanks for sharing!

• Tecra A11 - Compatible to express port replicator?

  Hey people, does anyone know if a Tecra A11 can be used with version PA3508E of the Express duplicator?

  Cannot afford the new while I'm between jobs, and I saw one of these 2nd hand on ebay.

  Hey

  Replicator Port Express is not compatible Tecra A11 and Tecra A11, you use the Port Replicator II with PA3680E-1PRP part number specifications.

  The second version of this port replicator is designed for these new models such as the Tecra A11 :)

• Tecra M9 and compitable motherboards

  Good day to all
  My Toshiba laptop Tecra M9 PTM91E - 12R features of a faulty video card.
  I replaced this card many times, but it's always get bad after a while.
  My repair shop of my recommended to replace its motherboard in order to get a solution permanent.

  I'm not sure if I am looking for motherboards Compitable with my product

  Can someone tell me please with PART NUMBERS of SPECIFICATIONS AND motherboards that I can buy?

  Thanks in advance for your support

  > Any can advise me please with PART NUMBERS, specifications AND motherboards that I can buy?
  Hmmmm... It is not as easy as you think. Defective parts will be exchanged on mobile units with only identical hardware components. It's a completely different situation than on desktop systems.

  You can visit the nearest Toshiba service provider and ask for help, but you will see that they will not be able to help you.
  Fact is that Tecra M9 was offered with two hardware platforms. PTM90E and your PTM91E.

  In the end, I must say it's really strange that you have an ongoing problem with GPU defective. When everything is changed on professional way and you take care of the machine and don't forget laptop is cooled properly I don t see the reason why it should be defective over and over again.

  For 3 years I have Tecra A11 and use almost every day for my small business and there is no problem at all. OK I use for typical every day activities such as web or MS Office and not for games or other graphics intensive applications.

  Try to contact Toshiba service provider in your country and ask for advice. They should have access to the material database of Toshiba and maybe they have good advice for you.

  If possible, send feedback.

• Re: Tecra A11 off when booting from a CDROM of Imagecast 6

  Hello

  I have two laptop Tecra A11 and when I try to boot with a CD of Imagecast 6, the laptop turns off.
  I tried with another cell A11 and it's the same thing. I tried to change the BIOS settings and an update of the BIOS but nothing works.

  Help!

  Hmmmm... How to help with the product that doesn't have much to do with Toshiba.
  You have other problems?
  For example when you try to start using the Toshiba Recovery disk?

• Need recovery disk or recovery for my Tecra A11 image

  I have a Toshiba Tecra A11 and had a problem with the operating system, so a friend offered to fix it for me, when he said fix what it meant try and install completely wrong Windows 7, but at the same time destroy the removal of the partition, all built in Windows 7 pro installation.

  So now I need a file or a CD specific boot to a USB key. Anyone know where I can get one or download one without having to pay 35 quid for a new Toshiba?

  Thank you
  Tom

  Recovery file cannot be downloaded. Toshiba offer as only recovery disk. Download an iso file won't help you much because you will not be able to start the recovery image installation.

  Either you find someone who has the same Tecra and use its disk or you must order one on https://backupmedia.toshiba.eu/landing.aspx

• Re: BIOS version 3.30 Tecra A11/M11: problems with Ubuntu systems?

  I just got the updated BIOS version 3.30 on my Tecra A11/M11 invitation.
  I'm still under Win7 now, but plan to add a dual boot with Ubuntu when the next LTS strikes in April.

  Is anyone having problems with the new BIOS?
  Should I upgrade or leave intact 3.20?

  I don't find any evidence of trouble with 3,20.

  Why upgrade BIOS if everything is OK?

  In addition to as much as I know that Toshiba can't stand not the Linux operating system, and I doubt that the new BIOS would improve any Linux performance so, if you are satisfied with the version 3.20, stay with that

• Tecra A11 (PTSE1A - 00L 005) - Dual boot with XP and Windows 7

  Hello

  Just bought a new Tecra A11 computer laptop running WIN7 Pro. Then downloaded and installΘ_ * virtual XP Pro * _ but not happy with the results that a lot of things he can do my other dual boot 17 "computer laptop with Vista/XP Pro will do.

  Background
  There are 3 partitions on the HARD disk
  1. active primary recovery 1.46 GB (without drive letter)
  2. principal asset C: start 287 Gb
  3 primary Partition 9.2 GB (no drive letter, the unknown application)

  Can I partition the C: drive in sectors 2 X 145 GB and make the new partition _ * assets * _NTFS?

  When I tried to install Xp Pro on another machine current Win7 partitioned as shown above, it 'blue preset' at the point of loading Xp using the RAID SATA CH8M-E charge via my USB FDD controller. Is it because this SATA driver is not current?

  What is the correct SATA driver?

  Does anyone know for sure that this machine will operate in dual boot Win7/Xp Pro?

  Any help much appreciated

  Peter

  Yes, you can dual-boot two versions of Windows.

  What you do is:

  Create recovery discs just in case something happens.
  Retractable C: drive at half the size.
  Create a new partition NTFS for XP.
  Download the driver for the controller SATA F6 www.intel.com
  Copy the SATA drivers on a floppy disk
  Boot from your XP (must have SP2 or SP3 slipstreamed) disc, press F6 when you are prompted to use the SATA driver on the floppy drive (to avoid the BSOD 0x0000007B)
  Configure the installation of XP to install on the partition that you created.

  When you restart, XP may have taken over and ignore Win7.
  In this case, you can restore the Win7 boot loader using EasyBCD (google is your friend)

  If the BIOS has an option of SATA controller Mode, simply activate the IDE Mode instead of the SATA driver.

• Tecra A11 - 113 - white screen and the cursor of the mouse during the boot

  Hello

  My Toshiba Tecra A11-113 with win 7 32 bit boots with a mouse cursor and the visible white screen.
  I tried to start under different boot options. Mode, safemode, last repair job configuration
  and msdos command only... all these startup options give the same result.

  I also tried with win 7 32 bit dvd, but same result.

  I am able to access the C drive by booting with a linux key, so the data is visible.

  Can someone please give me a solution?

  Thank you

  What happens if you access the BIOS? Is menu visible on-screen BIOS?
  Turn on the unit F2 button and press.
  This should allow you to access the BIOS.

  If you will be able to access the BIOS and see everything as usual, then the screen is OK and I think there is a problem with your installation of Windows System.
  So boot from the Toshiba Recovery disk should help you solve this problem.

  You said that you already tried to boot from the Windows DVD disc is this Toshiba Recovery disk? In my opinion, you use this disk to restore the laptop to factory settings.

• Tecra A11 - Win XP and Win 98 multiboot

  Hello

  I would like to make a multiboot XP / 98 on a TECRA A11.
  Don't you think it's possible.
  I have some drivers dysfunction?

  Thanks for the reply!

  Well, installation of Win XP is not a big problem because Win XP drivers seem to be available on the European driver Toshiba page.

  But Win 98 might be a problem here since his unsupported and drivers are not available, you need to find these drivers on your hand and I think that this could be a painful experience, I doubt that you will be able to get the Win 98 drivers because this OS is really, really old.

  I recommend you to install Windows 98 using Virtual Machine (VM) http://en.wikipedia.org/wiki/Virtual_machine
  or Virtual PC
  http://en.Wikipedia.org/wiki/Windows_Virtual_PC

  It is very easy in Win XP you can open virtual PC or VM and could start the Win 98

• Dual boot with Windows 7 and LINUX - Tecra A11 (PTSE1A - 005-00L)

  Hello

  I bought a new Tecra A11 computer laptop running WIN7 Pro. I want to install LINUX also. This means that I want to run my laptop in dual boot Win7 Pro/LINUX (a Distributor). Please tell me how to do this.

  There are 5 partitions on the HARD disk:
  1 active, recovery partiton 1.46 GB (without drive letter)
  2. principal asset C: start 145,04 GB (NTFS)
  3. active logics E: 78,13 GB (NTFS)
  4 active logical F: 64.25 GB (NTFS)
  5 primary Partition 9.2 GB (no drive letter, the unknown application)

  Hey, I need because I was admitted to a course of RHCE (Red Hat Certified Engineer)

  Please help me

  Hello

  I can't give you a step by step explanation, but most distributions offer today a possibility to coexist with Windows.
  When installing the unused free space will be taken by Linux (with the consent of the user of course!)

  What exact configuration you need is impossible for someone else to say, but I would say to make the space occupied by the F player available for Linux.
  You seem to have of enough space for Windows and Linux operating system doesn't have much.

  Some thoughts about setting up your score:

  I touch NOT 1,2 and 5 no matter what. They are your system and a system of internal partitions (recovery and data environment) and wouldn't it be fun to lose.

  1 active, recovery partiton 1.46 GB (without drive letter)
  2. principal asset C: start 145,04 GB (NTFS)
  3. active logics E: 78,13 GB (NTFS)
  4 active logical F: 64.25 GB (NTFS)
  5 primary Partition 9.2 GB (no drive letter, the unknown application)

  Then choose a Distro (Ubuntu, Mint, Fedora and OpenSuse - suggestion Fedora will be as close as possible associated with RedHat) that will guide you in the steps to allocate space for Linux.
  I suggest however to remove the disk F in Windows for Linux does not start from resizing all partitions.
  I do not know which works perfectly, but will just take time, and will most probably remain pretty useless drive F.

  If you have valuable data on your device, make sure to save! No software comes with warranty :)
  Last but not least - make 100% sure to create a collection set using the Toshiba Recovery Media Creator before you start the installation of Linux.
  If something goes wrong you have the opportunity to put the unit in factory condition.

  Good luck and keep asking you if you need extra help!

  Tom

• You will need to check on a PC with WinXP OpSys PUP. Could DO with Win98 and earlier versions. HOW can I make WinXP let me control BACK Pup?

  You will need to check on a PC with WinXP OpSys PUP.  Could DO with Win98 and earlier versions.  HOW can I make WinXP let me control BACK PUP?   Acquired CNC machines controlled by PRE - Win.XP PC works fine.  But Win.XP prevents the PUPPY control via simple BACK and GWBASIC.   You want to be able to start/stop all 8 bits of data PUP with BASE and BACK.

  Thank you.   Jan Rowland

  Hey Jan Rowland,

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited in the Windows XP Pro on the Technet Forums.

  Post your query in Technet Windows XP IT Pro Forums for assistance on this issue.

• I can't understand how to access my Creative Suite cloud computer crash. I pay every month for the student version, but it is not let me re - download now that my computer is fixed and back.

  I can't understand how to access my Creative Suite cloud computer crash. I pay every month for the student version, but it is not let me re - download now that my computer is fixed and back. Looking for help.

  Unfortunately, I was unable to trace any CC with this identification code Adobe is there any other Adobe ID in which you have saved CC? Please let us know

  Concerning

  Stéphane

• Tecra A11 speed on the fan at 100% all the time

  Hi, one of my colleagues has a new notebook Tecra A11. I've recently updated the bios to version 2.60 and since then the fan is constantly at full speed. Before the update it would be noticeable when the laptop has been widely used, but would slow down when idle. Anyone else seen/had this problem? I wouldn't mind flashing back to the old bios but can not see available on the web site of tosh.

  Thank you

  Hello

  In your case, I recommend setting the BIOS to the default value.
  You can do it in the BIOS. Insofar as I'm sure you could get press F9 default.
  But the option is mentioned in BIOS to verify this.

  In addition, I recommend changing the CPU and cooling module in Windows Power Options.

  This should help to reduce the speed of the cooling fan.

• Tecra A11 & Express Port Replicator II - USB problems

  Hello

  I'm having a problem with a port replicator that I simple couldn't have resolved for months. I'll try to explain this as best I can.

  We have a Tecra A11, which seems to work fine running on Windows 7 Professional. When the Tecra A11 is pluged in an Express Port Replicator 2, not USB ports in the port replicator's work at all. Very good cell phone fees and the LAN switches on the replicator fine, but the USB ports simly does not work under any circumstances. It would also be interesting to note that the green light next to the "eject" button lights never really.

  I downloaded and installed the latest series driver for Windows 7 from the Toshiba support page which has no effect. We had 2 replacements for Toshiba because they also agreed that the previous, we had were not woring correctly, but this obviously was not the case because we still have the same problem with our 3rd unit. The Tecra A11 was sent back to Toshiba with case notes clearly describing the question, and he was sent to us "no fault found".

  Unfortunately, we don't have any other laptops to test on the port replicator. but I'm seriously suspect that the problem lies in the laptop, rather than the port replicator. For any idea or suggestion will be greatly appreciated.

  Kind regards

  Steve.

  Hello

  According to your message, you are not sure if the problem is related to the defective laptop Tecra or express port replicator.
  Hmm theoretically the problem might be related to defective express port replicator or Tecra.

  If found some information on the USB ports and the repliators port:

  + Make sure that the element of Legacy USB in the BIOS emulation is set to "Enabled". This feature only works for the keyboard and mouse. Also note that the keyboard and mouse must be connected before you start the computer. A USB mouse, keyboard or the floppy drive connected to the Port Replicator via any other connection that a hub of the first level, will not work until the operating system has started. +

  I also recommend to check the version of the BIOS; If the most recent BIOS is available, then you need to update this