Tecra M2 - monitor problems

Similar Questions

• Toshiba Tecra 8000, monitor problem

  Hello

  I have a problem with my laptop Toshiba Tecra 8000, there is a green line with a width of 1 pixel on the screen of my laptop which does not disappear. the laptop is almost 2 years old. is there a possibility that it could be repaired? Thanks in advance,
  Mark Kuiper

  Hello

  interesting would be if the green line is permanently on the screen during startup or 'just' that Windows runs.

  But never mind, the laptop Tecra series three-year warranty.

  So in this case you can give it to a Toshiba repair for a control center upward.

  Good bye

• Tecra S1 - display problem, even on external monitor

  One day I was using the laptop, surfing the net normally, everything was fine and suddenly the screen went bad... (photo below). I tried using an external monitor and still the same, so I'm sure that my monitor is fine and it is probably a problem of display card?
  I tried to update my display card driver and no luck, so I decided to use the recovery CD to restore the system and no luck once again.

  Here is a screenshot after the system restore... y at - there a way to fix this without taking it to a service center?
  Thank you
  Link: [http://i130.photobucket.com/albums/p262/ctb205/mon.jpg]

  Hi borist,

  It s really great that you could post a picture of your problem. Thank you!
  In addition, you have already tried a lot of as the recovery facility and an external monitor.

  Unfortunately, it seems to be a hardware malfunction of graphics card. :(

  This means that you will need to swap the motherboard because the graphics card is fixed on it. Motherboard is a party quite expensive and Tecra S1 is old notebook then maybe you can get a second hand or laptop motherboard on eBay and swap it out.

  Good luck! :)

• Tecra A2 external monitor problems

  Recently, I broke the screen on my A2 and until I can afford to get it fixed, want to use a monitor tft external that I have. I use fn and f5 to enable vga but the resolution is all wrong, and when I try to change the tft screen is disabled and it is up to the laptop broken screen I can't see.

  Anyone have any ideas on how to solve this problem?

  Thank you

  Hello

  I put t know why you suggest that your resolution is fake because I checked the resolution display information and it seems that the max resolution is 1024 x 768.

  In addition, FN + F5 key combination doesn't change the screen resolution but display devices. You can use this function to switch from an extended desktop, external display and two screens.
  If you want to change the display resolution, so you should go to the display properties. Here, you can change the settings.

• Tecra 8000: monitor and the HARD disk does not work - does not start

  I have a laptop Toshiba Tecra 8000 given to me the year last by my uncle. I live in England, but it is and bought the PC in Italy. I do not know if this causes complications, but I thought it may be useful.

  Since I got it it occasionally did not display any image of all system startup, so if I have given some time and restarted it would start working again. Happening of bagan more frequently and now I can't make it work. I have conections and found that everything was in place. Then he doesn't seem to be turning on, however when I replaced the front LED cable seems to be turning on and although I couldn't hear much the CPU was luminous heat. I opened the drive and it gave once more, succeeded him and he still wouldn't start. I had purchased and replaced the screws on the heatsink around this area but I did not handle it with many other things.

  So now, I have a monitor that does not work and a gard drive that won't start... Any ideas?

  Thank you!

  Hello

  Could be either the card mother, CPU or ram. The processor when it goes bad or is not locked in place (have had this before, install the CPU but forgot to turn the lock, so he cannot move) the computer will act as its startup, don't give any error and stay on a black screen. Verify that the processor is locked in place. Then remove the ram and try a stick of RAM that runs on another computer. If you try the RAM and the processor do not always start, then chances are your motherboard is dead and must be replaced. Hope this helps and that solve you the problem.

• Re: tecra ptm91e video problems turning on

  Hello

  I have a tecra M9 laptop ptm91e.
  Its about 2 years old and I'm having display from powering problems.

  The screen is currupted, multi-colored blocks on the screen, but you can still see the info from the bios boot, and then it starts Windows, always with the currupted screen.

  Have you tried the new windows drivers just on luck, it might fix it

  Any ideas?

  Hello

  Before to start the discussion, how you tried to connect the external monitor?

• Print screen while using dual display on Tecra M5 monitors

  I have a Tecra M5 in a docking station, and I use the laptop as a primary monitor screen and an external LCD display as the secondary. Whenever I use the function Print Screen, I find that it copies both screens to the Clipboard. Is there a setting on the nvidia controls that will allow me to copy only the "active screen?" To avoid this problem, I find I have return to mode of single screen which is very irritating.

  Thank you

  Shuggy

  I assume you are using the desktop option on your machine
  This happens because the ALT + PRTSCN option creates a shortcut to the full desktop.
  If you want to create a unique desktop shortcut you don t need to use the extended desktop option.

• sound with lg monitor problems

  Recently I bought a LG monitor for mini mac. At the highest level, I can barely hear the sound. Used HDMI for the connection between the monitor and mini.

  Y at - it something I can do to improve it. Not a problem with the prior monitor.

  THX, mike

  The sound works OK when the monitor is connected via HDMI from another computer?

  Have you set the volume control of the monitor?

• 7.1 iMac monitor problems

  On restart, the screen saver seems fine... for about a half second.  Something happens which causes become very dark and too saturated colors.  The monitor calibration does not help.  By pressing 'shift' to reboot and then the connection has not helped.  Suggestions?

  Hi and welcome to Apple Support communities,

  What happens when you re - calibrate your monitor's color profile?

  Calibration involves a number of steps:

  Initial setup in which the contrast and brightness are adjusted, then native gamma correction to adjust the brightness of your screen, then the gamma target screen (which is 'desired' your screen gamma level), then the "white point" display for color correction, then the profile "name" and that concludes the basic calibration.

  You can also turn on "Expert Mode" If you want to go deeper with your calibration, but it's for users or if basic calibration will not give the expected results...

  If you cannot resolve the problem with the OS X screen calibration, then I suggest you have an Apple Store or authorized service provider take a look at your machine to check the defects in the operating system and the hardware.

  Good luck!

  Kind regards

  Peter.

• Satellite R630 - monitor problem

  I have a SATELLITE R630-13R.

  When I start my computer the systems sound works but the display to load the toshiba and windows splash pages, then remains empty.

  If I open in safe mode, the light is very good.

  When I attach an external monitor, I can see the desktop in normal mode and everything works fine.

  What can I do?

  > When I attach an external monitor, I can see the desktop in normal mode and everything works fine.
  Put back to s notebook combination of keys FN using LCD / external monitor disconect. Restart notebok and let us know if the problem stil persists.

• Tecra A2 - mouse problems

  I have some problems with the external mouse on my tecra A2. The pointer seem to 'jump', sometimes across the screen, and it's pretty boring. I'm not sure of what the cause of the problem and still less what to do about it... The mouse is a Logitech optical mouse. I tried to change to a similar mouse but that did not help...
  What should I do?

  Hello

  Try disabling the touchpad through FN + F9. Did you try it with mouse just wireless? You can try it with the mouse that is connected with a cable?

  Sometimes I have the same problem, but it happens if the batteries are empty or if the mouse signal receiver is placed on the wrong place.

• Tecra A2 Sound problems

  I bought a second hand Tecra. I can't play any sound out of it. When I go to sounds and Audio, under audio devices, it says "no Audio device". When I go in the material, he said all devices work correctly except for the Multimedia Audio Controller, which according to her, the "drivers are not installed (code 28). When I try to install the Realtek drivers AC 97 system said that they are not compatible with XP and landfills eventually get out me.
  Can offer you any advice / solutions to this.
  Thank you very much
  Melody

  Hello

  This is especially a problem with driver. Go to the page of the Toshiba driver and download the audio driver for your model:

  http://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp

  Install it and then restart.

• Tecra M4 boot problem - missing or damaged ntoskernl

  Hello

  I have a Tecra M4 running Windows XP Tablet Edition, which fails to start due to "a missing or corrupt ntoskrnl.exe. According to the MS website I can solve it using the installation disc, but I don't have one that I bought the laptop from my employer when I retired. I was told that my installation is legal and have the license number.

  I tried to get a Toshiba drive, but it seems that the machine is too old.

  Anyone know where I can get a drive to. If it is not possible to find the same version of the operating system can I can use an installation disk XP Pro standard (I could buy on the Internet), even though my system is the tablet edition. I don't want to take the risk to wipe my data, because even though I have most of the stuff saved there are has some important issues that are not.

  Any help appreciated.

  Thank you

  Barbara

  Hey,.

  Yes, that is a known issue regarding the ntoskrnl file and you need a Microsoft Windows disk to fix this problem in the repair console.

  Are familiar you with Windows repair console? I ask this question because you need to use the DOS command line based to solve this problem, there are GUI. If so ask a friend if they have such a drive and normally the professional XP disk should also work.

  Otherwise, you will have to reinstall the whole system :(

• Reader of SD with Tecra M2 driver problem

  Hello

  I formatted my laptop: TECRA M2 PTM20E-0R1LZ-FR / PM 735

  I found all my drivers for all execpt for the SD reader componet.

  It was very difficult to find the SD host controller, but I finally found it:
  Toshiba Secure Digital host controller
  oem17.INF:Toshiba:SDHost:6.0.4058.0:pci\ven_1179&d ev_0805

  But now, when I insert my SD card, I have a problem with the SD reader driver.

  So, if anyone has an idea...

  I did all the forum, all the driver toshiba support page and nothing on that kind of driver.

  Thanks for your help.
  Kind regards
  xVZx

  What type of problem do you have when you insert the SD card?
  Do you use drivers from the Toshiba support page?
  Do you use took in charge a card SD (support capacity)?

• Tecra M2, sound problems

  I can't get any sound on my tecra m2 at the present time. Its been like that for a few days. The volume is not cut or something like that and I can not see what is the problem, can anyone help?

  Have you tried to turn the Volume control on the front of the Machine?

  Good bye