Tecra M3 dark display, checked the usual problems

Similar Questions

• Tecra 9000 - no display on the LCD screen when you turn on

  I recently got a Tecra 9000 for cheap on eBay. I am experienced with the construction and repair of computers, but not so with laptops.

  The problem with this laptop, it's that do not display on the LCD screen when you turn on. It was just black, no backlight, nothing. I took the laptop all share, found no obvious problem. I had to turn it on and the screen lights up a few times trying to figure out the problem. Would it be a bad connection? Or something else?

  After getting it to start work, I'll try to start to put it back together and it stopped working again. I haven't not been able to reduce it to know if it's a bad connection or a card problem.

  Someone at - it suggestions? This is a problem for others here?

  As you describe the issue, I think it is somehow a bad connection or a damaged cable, because it does not work once you have disassembled the screen.
  Maybe you need to check all the cables, leading motherboard to the LCD and take a close look, maybe for a few scratches or strong curvature.

• Tecra A10 - poor display through the port replicator

  I have an error with one of my clients, they have 3 x Tecra A10 is bought in the last three months, the last time being last week.

  I get a very poor screen through the port replicator, lines running through the screen almost like the lines of scanning, or RF interference. It happens on all three laptop configurations.
  We have new Phillips 19 "wide and 22" widescreen, I also tried a HP 19 "wide where else in the company. also having the same problem. These monitors are working 100% if hooked up to a computer or DIRECTLY into the laptop A10, as soon as you plug them into the cradle we get lines through the screen.

  I'm learning to communicate with the provider in order to replace it, because I have three already do the same thing, I'm pretty sure that I will receive a fourth with the same error.

  Someone else has the same problem?
  According to me, this issue has been raised on another forum, but was not answered. Does anyone have a solution?

  Please can you tell us which port replicator you use and which port replicator port?
  BTW: you are an authorized service provider?

• Media Center cascade have not all photos - not the usual problems

  This isn't a matter of marking and refresh. I searched on the net for weeks and I have not found someone with a similar question. Basically the waterfall poster only a fixed number of album covers from A to somewhere through t. tried to add in music by alphabetical order, letter by letter and refresh the cache of art every time, and it always stops updating at the same point. I tried to add music in reverse order of Z back in the same way and I get the same result when I arrive about G.  I guess the cache album_art is limited, but I can't believe that no one else has had the same problem. My music collection is not that the large = about 70 GB / 1200 albums.

  Any help gratefully received.

  Hello

  Check with those on the green button using WMC.

  The green button
  http://www.thegreenbutton.TV/forums/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Satellite Pro M10: Display of the strange problem

  I have a M10 Pro of the Satellite with 14 inch display is 6 weeks out of warranty.

  The other day, I got cold room and the display went funny - odd pixels, green and black with small points which then becomes more clear screen so that the entire screen is a mixture of points fluorescent which becomes white and then things come back.

  Then, the cycle repeats itself after a few seconds.

  I perform a restart and everything's going well for a while, and then it restarts. I move the laptop in a cold room and it's ok again. I can't understand that the issue occurs on Windows XP and SUSE 9.0 (although it just hangs). I have run SpyBot, have the latest virus checkers, the update of Windows (SP2) and NVidia drivers.

  Any ideas?

  Seemed to have solved the problem by dismantling the machine, could not do not get all the way and completely remove the top from the bottom as there seems to be a hidden screw. Everything is fine now, could have been the fact that some of the screws were loose.

  Also had a full SpyBot and Virus Check.

  I also had to re - save under a different name, since it is "Specific country" even if I thought that I had, I now have three profiles - two I created recently, and one I could not remember the username for, would be really better if password request tells you the user name to an e-mail address it is registered. It's really hard to keep track of them so I have a lot of connections as a computer scientist. Really really annoying and stupid system.

• Tecra 730XCDT size display - possible to repair problem?

  In 1024 × 768, the screen is full, but change to 800 × 600 and 640 × 480, the visible screen shrinks a bit and drastically in that order. Is it possible to get a screen resolution less than completely fill the display area?
  I already have the BIOS to stretch the text, but there is no parameter to stretch the graphics.

  If anyone has had this work, they can send me the name of the driver file, and I'll hopefully find somewhere to install it?

  Sorry mate but could you please start with some details by providing more information about your model Tecra and preinstalled Windows system?

  The XCDT series seems to be old and I mean very, very old post so not quite sure if the community would be able to help you, however, please the information required above.

• Windows Update - not the usual problem (it works!)

  Windows 7 SP1; Windows Update works, BUT when it's an automatic check (daily?), that it takes about an hour and fully use a CPU at 100% during this period.  Pointers appreciated.

  Please run the Windows Update Troubleshooter:
  http://go.Microsoft.com/fwlink/?LinkId=231149

  Please provide the exact details of any problem it reports as not fixed.

  Windows Update error codes
  http://answers.Microsoft.com/en-us/Windows/wiki/Windows_7-update/Windows-Update-error-codes/bd72b821-05bf-4EFD-BEA1-b0be08fffe54

• Check the printing problem

  Hi gurus,
  
  
  We have problems when printing controls in EBS, there are a few special characters also got cheques printed on if need to reload the MICR fonts. Can someone guide me how to reload the file of police of MICR to EBS 12.1.2 runing on RHEL 5.3 to print cheques?
  
  Thank you
  Shashi

  Please see these documents.

  How to configure, map and print reports customized with a barcode / snowmelt MICR [551630.1 ID]
  Check printing using XML Publisher [ID 312353.1]
  How to implement an AFM / AFP Barcode or in an EBS UTF8 Instance [466531.1 ID] MICR Fonts
  How to install special fonts (LP, barcode) in Enterprise BI Publisher [ID 557275.1]
  RTF models lose field of barcode information after you change the file in Word [ID 1060832.1]

  Thank you
  Hussein

• Where can I find instructions for de-Assembly of laptop Pavilion DV5 to check the screen problem?

  Hello

  Excuse me for my bad English, I «m french...» Sorry...

  I need to change my laptop screen and I don't know how to do...?

  Is there a manual for this product?

  Thanks for your answers...

  http://h10032.www1.HP.com/CTG/manual/c01550108.PDF

  Make sure you're statically unloaded prior to entering your laptop and the battery and adapter are disconnected.

• Satellite A660 - display problems, very dark display

  Hello

  I'm at the end of help please.

  I have a Toshiba Satellite A660 PSAW3A-07P00R.

  recently, it has been very, very dark display on the screen, almost impossible to see.
  I tried the following the problem solved.

  1. set the brightness to the MAX in the operating system, power management, etc.
  2 reset the BIOS to default settings.
  3. set the brightness to the MAX on the laptop brightness settings.
  4. check the external display via a VGA cable. tested ok.
  5. I bought a new LED 16 "screen but the new screen has the same problems. If I understand correctly, LED screens (1 data cable video on the bottom of the screen to connect to the motherboard) have the "inverter" built into the display, so appears not to be a problem of map display, brightness or graphics. I would be fair to assume that this is related to the data cable from the screen? If Yes, is a piece that can come from Toshiba? or something easily fixable?

  is there something easy, I missed, or something I have not tried?
  has anyone else experienced this problem and solved?

  Thank you in advance.

  > I would be fair to assume that this is related to the data cable from the screen? If Yes, is a piece that can come from Toshiba? or something easily fixable?

  As much as I know there is no FL inverter then, or you can override the display or the cable (LCD/FL)
  LVDS cable) with a new one and the test shows again.
  I found a compatible: K000103140 LVDS CABLE

• Tecra A4 - ATI display driver problem

  Hello I have this problem in my Tecra A4 Display driver, the mobile hangs and write this journal in Nevada Viewer:
  Event type: error
  Event source: ati2mtag
  Event category: no
  Event ID: 108
  Date: 02/07/2006
  Time: 15:06:32
  User: n/a
  Computer: QUIMERA
  Description:
  The ati2dvag driver for the display device \Device\Video0 got stuck in an infinite loop. This usually indicates a problem with the device itself or with the incorrect programming hardware device driver. Please check with your hardware device vendor updates the driver.

  For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
  Data:
  0000: 00 00 00 00 03 00 52 00... R.
  0008: 00 00 00 00 6 c 00 04 c0... l... TO
  0010: 00 00 00 00 00 00 00 00...
  0018: 00 00 00 00 00 00 00 00...
  0020: 00 00 00 00 00 00 00 00...

  all the solutions for this?
  Thank you

  Hello

  Try to install the latest driver.
  See this page:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

• Tecra A7-112 of display cannot display all the colors corectly

  Hi, I have the same problem with my screen than that of this post: http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=14718&messageID=54000

  It seems that my screen may not display all colors corectly and it seems protected by a kind of tasks/works of art in most colors.
  Here is a picture, not so good but still, my question:

  http://www.Logicode.ro/test.jpg
  http://www.Logicode.ro/Test1.jpg

  You can see the first color - pure red it seems correct and solid but second it - a small red varation there artifacts / protected by a kind of tasks.

  I learned that it is a problem of dithering that can be set in the BIOS.

  For the Satellite A100-237 the problem has been resolved by downgrading to an older version of bios, but what can I do with my laptop Tecra A7-112? :|

  Post edited by: eStatic

  Hello

  Have you checked whether the BIOS most recent update has been published on the driver page?
  I put t know if it helps but you can also try to update the display driver.

• I have a complaint on my Mac Book Pro. I bought my computer in January 2016 and it has two problems: the first is the display of the retina that has many traces of the keyboard and as many times it freezes. I have looked for help on the local Apple Store

  I have a complaint on my Mac Book Pro. I bought my computer in January 2016 and it has two problems: the first is the display of the retina that has many traces of the keyboard and as many times it freezes. I have looked for help on the local Apple Store and support too, but it did not help. I would like you help me solve this problem.

  Thank you.

  Kelly

  Your machine is still under warranty, so you should take it to your local Apple store for repairs. Function late in January, you bought it, you still have phone without support. If you can't find any help on the Apple Store, then I don't know what you expect to find here. We have no way to check for problems you have described or any additional hardware, etc.

• Tecra M4: Known issues with the display of graphical interfaces user written in Java?

  Hello

  I am developing software in Java which will run on the M4 model and have acquired a M4 to test the application.

  In fact, my GUI looks good when the monitor is in a normal "standing" position. However, when I fold the monitor down and transform all a TabletPC, I see the M4 is an empty JPanel.

  The GUI is written using the swing and consists of JPanels nested with GridBagLayouts.

  I tried to update the OS and my graphics drivers with no luck. First of all I would like to ask if anyone else has experienced similar problems and if so have any suggestions on how to fix?

  My M4 runs the same hardware/software that it came with Toshiba and I use jdk 1.5.

  Kind regards
  Ivar Nilsen

  Hello

  Have you used the new graphics driver Toshiba?
  Please check the Toshiba driver pager:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  You will find a display driver for nVidia card. The latest version 6.14.10.7141 is the 14/06/05 maybe that helps.

• Problems with the display after the update of Windows

  Hi guys,.

  I have not installed or updated all programs on my computer for at least a few weeks, with the exception of Windows Update, so part of MS updates, nothing has changed in recent weeks.

  A few days ago, my computer (HP dm1 laptop computer) screen acted funny - I took a screenshot of what happens and posted here:

  http://DL.dropbox.com/u/1076277/desktop_problem.jpg - basically, the display is all messed up with repetition of lines, etc.

  At first I thought it could be a driver problem, but the drivers are ok and were not being updated - in fact, in addition to the usual updates, the only new was the new update now live.

  I did a system restore (restore a week) and everything seemed normal again - this problem is intermittent, but very frequent, but within a few hours of use, there is no problems - until I run Windows Update, and it all started again...

  Any suggestions as to what might be the cause of the problem and a solution? I don't really have the time now to keep stable each item in the update...

  Thanks for the help.

  Hello

  If you want to study, it will take time but you can find the offending update.

  First update all updates (redundant, uh?).

  Make a note of all of the updates (KB numbers, etc.).

  Restore and install the updates one by one and not simultaneously.

  This way you can find the update 'wrong' and later come to conclusions based on what it is supposed to fix.

  Carlos