Tecra M3: FBCF display problem

Similar Questions

• Tecra A3X - Intermittent display problem

  I have several of this A3X laptop computer, with build different versions, but the latest display drivers. Probably bought at the same time.

  It is an intermittent fault which has no template. Users encounter while using, so that the graphics appear goes and they are presented with a screen, can be either white, green, blue or purple.

  The only way to resolve is hard boot the PC with on/off switch.

  I plugged an external display while he did and the graphics appear ok on an external monitor. Is there a flaw known with graphics display on of the A3X?

  I contacted Toshiba, who advised the re-boot, which suits him.

  Updated the display driver graphic for the last patch, fault still occurs.
  Cell phone everything rebuilt, fault still occurs.
  Check all connections in the laptop display, re-sitting all connectors, down again.

  Can anyone tell what to try next?

  If the default does not appear on the external screen then either it's a faulty inverter FL or bad display itself.
  Presumably why this happens, but in my opinion, it is meaningless because first it will not help to solve this problem and then the laptop parts are always stressed and these defects occur simply.

  What to do do so only one real solution. The parts must be replaced or repaired.
  I guess that the technicians don t fix devices individual but replace it with a new one.

  Speak, the least reflection. you simply contact the ASP in your country for the control and the fix.
  If the warranty is valid, everything must be done for free!

  Best regards and good luck

• Tecra S1 display problem

  Unfortnately my tecra s1 hit the table of coffee on the ground, the screen immediately turned white. When I rebooted there was no display at all (black only)
  The computer works as I plugged on a screen external and that was very good. I tried to follow various troubleshooting guides online showing how to disassemble the laptop and reinstall the connector of the display on the motherboard, but this did not remedy the problem.

  I noticed coming from the display was a big bunch of wires going into a connector that I reinstalled, on the right hand side of the screen is a white and black wire to a connector and a pink wire that seemed to just float, I couldn't not whence he came. Does anyone have ideas on the subject of this thread or other tips that can help me.

  Thanks in advance

  Hello

  Unfortunately, mate, you won't find any manual disassembly here on the pages of Toshiba. These manuals are not for use public and designed only for the FSA.
  But I think you could google a bit and you should find a few details.

  I think that it is a display problem that I doubt that some loose cables could cause this problem
  In my view, the screen is broken and needs to be replaced
  To do this, you should get in touch with your technician ASP.

  Good luck

• Tecra M3 dark display, checked the usual problems

  Hello

  My M3 went dark, it flickered on and off for about a week and then completely dark. I still work if I get the right angle and an external monitor is fine.

  If haven't tried a new cable from the screen, no difference and a new inverter, also no difference.

  Sometimes if I switch between views (Fn + F5) I can get the display works fine, but as soon as the screen is turned off for some reason it won't once again.

  I also re-greased the heatsink on the NVidia chip.

  And I checked the backlight by plugging a converter working on another laptop.

  I have a M1 and there is a relay type sound when something has changed on the screen, I can't remember if the M3 never makes a similar sound, even if I used it for about 5 years.

  I also saw that he suggested that he might think that the cover is closed, I don't know how the M3 detects that the lid is closed.

  Any suggestion or help would be welcome.

  > My M3 went dark, it flickered on and off for about a week and then completely dark. I still work if I get the right angle and an external monitor is fine.

  This means that the graphics card chip was Ok, which means that it could be a display problem
  I doubt that it ups s related question. If FL inverter would be defective, then you'd see everything on the screen, but everything would be visible behind a thick fog.

  Of course, it s that my personal opinion and nobody would be able to tell what dysfunction part without running any hardware, test procedures
  Then maybe you should ask a support technician

• TECRA S1: No display

  Hello

  I have been using my TECRA S1 for awhile. It worked fine with no problems until at some point when I start the pc it didn't display.

  I tried to check on the LCD cable. I have Plug and then plug it in. When I start the pc again I could see the display, but only for a few minutes, then windows XP hanged.

  When I rebooted the pc the no display problem occurred again.

  The rom cd and CPU fan works. The disk hard led will blink twice when starting, but I don't think that it was able to read the hard drive.

  I also checked my RAM modules are works fine with a different toshiba pc.

  What could be the problem?

  Hello

  Sorry, but your ad is a bit confused.
  Do you have a problem with the display of the computer laptop or external display?
  If you have the external display to malfunction please check the display properties.
  In addition, if the operating system suspended every time, you can try to recover the operating system with the recovery CD. But first, you should make a backup of your system.

  Good bye

• There seems to be a display problem. Please check that your monitor is HDCP and is not mirrored by using Airplay.

  There seems to be a display problem. Please check that your monitor is HDCP and is not mirrored by using Airplay.

  Apparently, you're trying to use AirPlay to display content that is protected in a way that not only allows the copy.

• Retina MBP display problems

  I vaguely remember that there is a kind of reminder for display problems on some models of MacBook Pro retina. I don't remember the nature of the issue, nor the accurate models who were eligible. I have a 15-inch model, end of 2013, and what I see is pictured below (dead pixels). Can anyone remember if there was a recall and that this issue would be covered?

  

  2011-2013 models.

  To my knowledge the retinas did not have a reminder. However, I got my rMBP 2012 15 "screen changed due to ghosting. I do not know if Apple which is still.

• In the visualization of my photos display problem: I have red spots in different parts of the pictures. Someone knows how to fix this?  I rebooted my MacBook Pro, but it does not solve the problem.

  In the visualization of my photos display problem: I have red spots in different parts of the pictures. Someone knows how to fix this?  I rebooted my MacBook Pro, but it does not solve the problem.

  Details please

  What version of Aperture? Is OS X 10.7.5 as you say correct for your OS? You shoot JPEG or RAW? If RAW device? Wharton has changed since this worked?

  LN

• Mac book air display problem

  having display problems with my macbook air, first version of 2015. When I turn on my macbook, after entering the password and pressing on enter three lines (not really lines they look more like lightning, appear from the top of the screen) in the colors Blue, green and red.

  also when I turn off my laptop just until the display on the top of the screen this thick green line 3 inch appears and goes about a second or 2.

  help someone?

  Thank you

  Try a reset of the NVRAM:

  https://support.Apple.com/en-us/HT204063

  If no success, take a picture of the problem.  Make an appointment at an Apple store genius bar for a free evaluation.  If necessary, show the technician, an image of the screen.

  Ciao.

• having display problems with my macbook air, first version of 2015. When I turn on my macbook, after boarding the password, then press on enter three lines (not really they look more like flashes coming from the top of the screen appear) in

  having display problems with my macbook air, first version of 2015. When I turn on my macbook, after boarding the password, then press on enter three lines (not really they look more like flashes coming from the top of the screen appear) in the colors Blue, green and red.

  also when I turn off my laptop just until the display on the top of the screen that is 2 and a half inch thick green line appears and goes about a second.

  help someone?

  Thank you

  Howdy Yaser of zoysia,

  It seems that your screen displays some graphical anomalies when you connect to your user name. I would use these troubleshooting steps in the following article on the resolution of screens:

  Restart your Mac in safe mode to reset the default display resolution.

  If booting safe mode doesn't resolve the problem, reset your Mac NVRAM and SMC to reset the video ports on your Mac to their default values.

  From: get help with graphics issues on external displays connected to your Mac.

  Thank you for using communities of Apple Support.

• On Tecra A9 BIOS password problem

  My computer laptop Toshiba Tecra A9 have a problem with the BIOS password and I was wondering if you could provide me the password because I can't access anything whatsoever, without it

  BIOS password is very important security feature and these issues cannot be clarified on public forum.
  Any problems with the BIOS password must be clarified with the Toshiba service provider.
  If your laptop is blocked by password and you cannot access, please contact the nearest service Toshiba and they can remove it for you.

• Display problem on my A60 Pro Sat

  The display on my satellite A60 pro features a strip of wide pixelated of 6-7cm at the bottom that hides my mouse cursor and the taskbar. The mouse is still active behind it. Mode full screen using an external monitor is seen. The group changes with my office window or active but is just vertical color bands. What is the problem and can get rid of him.

  Hello, Robert

  Have you changed anything on your device or this occurs suddenly display problem?

  I'm really in idea. If you want you can reinstall the unit with recovery DVDs. If the problem persists it is obviously a malfunction of the display. In this case, you must contact partner in your country.

  If there is some serious hardware issue please let us know.

  Good bye

• The viewer or split display problem: I am getting small white boxes (similar to those seen in the browser) superimposed on my photos. Any ideas how to fix?

  The viewer or split display problem: I am getting small white boxes (similar to those seen in the browser) superimposed on my photos. Any ideas how to fix?  There must be a display problem in the software.

  Have you of the 'show Talking Points' enabled in the view menu? Then you can see small white boxes superimposed on the image in the Viewer.

  

  You can enable or disable on / off power with ⌥F talking points.

• Graphics/display problem - Satellite M60-105

  I'm having a little problem with the display (or graphics). In some programs of CAD (Inventor, Solid Works) 3D solids are displayed with lines that normally are not displayed. "I see the solid. In the games like Doom3, I see only a chequer (Exchequer) with black, the blind, the tasks of rectangle. I tried to update the graphics driver, but the results were the same. Problem is more complex that I have thaught, because I noticed the same problem after formatting HD and mounting of Toshiba Recovery CD. Also, I noticed the same thing happens when I'm trying to change something in the BIOS. Maby some of you have had a problem like this, please help.

  Hello

  Believe me on this path is not easy to say what may be the problem. The explanation of your problem is good, but it will be interesting to see what you mean exactly.

  One of my friends has M60 and I didn't see any display problem on his unit. If the unit is installed with recovery media that produced with other applications, watch DVDs or simply with 3D CAD program?

  It will also be interesting to know what you exactly changed in the BIOS.

• The satellite M60 display problems

  Hello

  I bought a satellite M60 a month ago, and since then, I've been strugling trying to solve a problem that has to do with the display (ATI 700 X mobility).
  When I play some games (the dawn of war, Unreal tournament...) the computer freezes completely, I actually have to force stop it to restart.
  Another problem, that I have seen is with Mixmeister Pro 6, the video playback is erratic, it is as if the computer is unable to handle any overload.

  I tried the upgrade of drivers, nothing works, then I installed the third party Omega drivers, but once again, nothing to do.

  Since the purchase of the M60, I had to correct problems of Wirless and PCMCIA card through driver updates, but there is nothing that I'm be able to do to resolve this display problem.

  I am quite convinced it's a driver issue, but then again, nothing is certain.

  If anyone can help me please I'm getting desperate.

  Hello

  Well, it's not easy to say why it happens but one of my friends has sometimes even appearance but on another unit. If he plays a high-performance games unity cling.
  In my view, this could be a heating problem. Playing games is hard work for the laptop, because all parts (bars of memory, processor, graphics card, etc.) work with max performance and produce a lot of heat. Most laptops are not developed for this.

  However, you should always use the graphics driver from Toshiba. I found the latest version of 15/07/05. It is a display 8.121.050.322A driver. In addition, you must install latest DirectX. I think that it s a 9.1. Check whether the fixes for these games are available.

  Second, if video playback is erratic, it seems that the OS is fully committed.
  In this case, you should check the processes that run in the background of the operating system.
  In addition, try to defragment the HARD disk

  Good bye