Tecra Z50-A-14 t - bad connection WiFi signal

Similar Questions

• Bad connection WiFi on my Portege R930-15E

  Hello

  I have a strange problem on my R930 which I tried to solve already for several months, but could not succeed.

  As I recently replaced the WLAN router and the problem remained to the laptop, I know now that it's really the Toshiba which hurts.

  Question: The WiFi is on the 2, 4 GHz WLAN and there are only two local wireless networks here in the neighborhood. The intensity of the signal is supperb (5), but the speed of the network status changes in a few seconds between the 26 and 130 MBit according to the diagnostic tool for Windows 7 (without doing anything with Notepad). I would not care about it if WiFi would work well, but it's not.

  Download videos from YouTube makes sometimes troubled (videos are stuck) but the most important problem is that access to the data to our NAS is really bad.

  I know it can work much, much better that I have also two other laptops that work well, both HP, older than 7 years, shows no such a question, signal WiFi is still at 54Mbps or, on the new, with 150 MB / sec. Other tablets and smartphones also do not have these issues.

  I tried already to have different channels, but does not help. I've updated also the WLAN, the last driver of Toshiba seems to be: Intel Centrino Advanced - N 6235 Version 13.03.2012 15.1.0.21. Is this really the last being?

  In addition, I found around many problems of WiFi in the Toshiba Internet, but so far, none really match my situation.

  But I found that Toshiba seems to have bad WiFi antenna, but I sat just 5 meters from the router, so I don't think that it's a software problem (driver). Operating system is Windows 7 Professional 64 bit.

  Do you have recommendations for me what to do?

  Thank you

  Volker

  Hello
  Indeed, Portege R930-15E was equipped with the Intel Centrino Advanced-N 6235 WLan/BT combo card that supports the 802.11 A/G/N standards.

  The latest driver should be available on the Intel page:
  http://www.Intel.com/p/en_US/support/highlights/wireless/can-6235

  It seems that the latest driver (at that time) was published at 29/12/2014 and its v15.14.0.1 for Windows 8.1
  Anyway, as you can see, this WLan module supports the 802.11A/G/N standards.

  I think you should check in the Device Manager-> properties-> Advanced tab WLan card which WLan standard was chosen. Probably, you could change cela a/g or just N

  Last but not least, I would recommend allows you to check the WLan Card power saving option.
  Option for WLan module energy savings are in the advanced power settings and I recommend you to choose for two profiles (dough/adapter) the performance of the value

• Tecra Z50-A-130 - LAN over WLAN connection

  My Tecra Z50-A-130 with Windows 7 Professional prefer a WLAN connection over a LAN connection.

  When I have a LAN connection available I prefer the LAN connection (speed is better), but my laptop auto activates the WIFI connection.

  Is it possible that my laptop active automatic connection of the local network when available, prefer it over the wireless LAN?

  Why you n t turn off WiFi if your laptop is connected to the local network?

  However, usually Windows controls this connection automatically to change this, you will need to change the priority.

  1 click Start, in the search field, type view network connections.
  2 press the ALT key, click Advanced Options, and then click Advanced settings...
  3 select Local area connection and click the green arrows to give priority to the desired connection.
  4 after organizing network connections available according to your preferences, click OK.
  5 the computer will now follow an order of priority when the detection of the available connections.

  More details here:
  http://Support2.Microsoft.com/kb/2526067

• Tecra Z50 - need to connect two external monitors

  I think to buy Tecra Z50, but one of the features that I need is the ability to connect two external monitors.

  Is it possible to have a monitor connected to the HDMI and a VGA (with computer laptop lid closed)?

  * Hi-speed III Port Replicator is not an option, because it is not available in my country (Croatia).

  Hello

  I don t think you will be able to connect two external monitors to this laptop using HDMI and RGB port at the same time because of different types of signals.

  The RGB/VGA port supports analog signal.

  The HDMI port provides the digital video output and when the external monitor is connected to the HDMI port the device is set to HDMI.

  > * Hi-speed III port replicator is not an option because it is not available in my country (Croatia).
  What of the Dynadock? Its an external device connected to the s for computer laptop USB port.
  It supports own graphic unit and you can connect to another external monitor such Dynadock 2nd.

• Tecra Z50-A-12 X is not properly connected to the Port Replicator III

  Hello

  I just bought a TECRA Z50-A-12 X with HI-speed III 120 replicator Port Replicator.

  It works but the computer is not stable and I fear that this will eventually damage the port see me problems when using.

  Indeed, the PC sits well in the Replicator.

  Is there a solution or did not have this app?

  Thank you for your response.

  Nice day

  Hello

  Please don't get me wrong, but you should clarify this with Toshiba directly. Here on this forum, you can hear some useful opinions and comments, but I think you should get info straight from Toshiba directly.

  You can also do is to contact the nearest Toshiba service provider and ask for help. You can visit ASP and demonstrate how it works and I hope that you will get a professional opinion on this problem.

  Long ago I had a Tecra laptop with port replicator, and he was well in place and really does so port replicator he not there no danger of damage to the small port located in the lower corner.

• Tecra Z50 - mSATA SDS + 2.5 "HDD?

  Hallo!

  I've seen in a Youtube video, that the SSD that come as standard are mSATA those and that there is space for a 2.5 drive "under.

  So my question is: if I buy a Toshiba Tecra Z50-A-12R, which comes with a 500 GB HARD drive, can I install an additional mSATA SSD as my system disk and using the 500 GB HARD drive as a second drive?

  Thank you
  Martin

  Well, some models are equipped with an mSATA Solid State Drive (SSD) instead of one
  hard disk drive. The computer seems to supports a 128 GB and 512 GB disk SSD 256Go

  but as far as I know there is only a single SATA controller to connect a HARD drive or SSD.
  The mSATA SSD drive is connected to the controller using mSATA HOLDER ASSY.

  So this cpl carrier is necessary if you want to use an mSATA SSD.
  Of course, you n t need if you use common disk 2.5 SSD or HDD 2.5

• Tecra Z50-to-17 t constantly freezes during shutdown

  My new Toshiba Tecra Z50-to-17 t constantly crashes on shutdown.

  At first I thought that it could connect to the Cisco all lie, as it appeared in the event viewer several times.
  After I deleted it went well for a while, but now the problem occurred again, but this time there is nothing to see in the event viewer.

  Can someone help me what is wrong and how can I fix it myself?

  Hi friendly smirou

  The laptop has been preloaded with Win 7 64 bit system.
  I guess that you are still using this system, I would recommend you to repair the system using the windows have auto repair function.

  Start Notepad, and then press F8.
  Now you should be able to access the Advanced menu.
  Here, you can choose between different options.

  You can choose the last known good configuration option.
  You can also choose the first option to fix your computer, which will open the next window, where you can access the Startup Repair feature.
  There, you might choose the Startup Repair option

  Otherwise, it would be desirable to recover the computer laptop back to settings factory just to check if its a system single or maybe hardware problem related question

• Tecra Z50 - A - Intel Rapid Storage Technology does not

  Dear Sir

  We bought a lot of laptops Toshiba Tecra Z50 - A with a hybrid HDD (with SSD cache).

  The exact model:
  TECRA Z50 - A
  PT544E-00D01TBT

  We staged and repartition laptops via SCCM.
  However, when you install all the drivers and the Intel Rapid Storage Technology software, I see that only rge WHAT HDD is used and no partition SSD with the Intel RST.

  How we enable this?
  The problem is that the performance is incredibly bad.
  Laptops are very slow, even if the specifications are good:
  CPU i5-4200U
  8 GB RAM
  Windows 7 x 64

  No idea how to turn this Intel RST?
  In the BIOS I find no option for RAID, as must be enabled for the RST to work.

  Thank you

  To be honest I n don't know what you mean exactly the RAID mode. There is no RAID mode.
  The laptop was equipped with a 500 GB SATA HDD HYBRID.

  The part of the HARD drive is used for writing, the SSD part for the reading of the data.
  The performance of SSHD can be placed between a HDD and SSD, but it s significantly slower than an SSD.

  If you have already installed the - Intel Rapid Storage Manager driver, then the service should work

  In the case where it does not run in the background, try to install the latest Intel RST page of Intel driver.

• Tecra Z50 - A - 11 c: external display do not wake

  Hello

  I've got Tecra Z50 - A - 11 c and an external display connected to the VGA port.
  I implemented the plan of power management to turn off the screen after 10 minutes.

  The monitor turns off after 10 minutes of inactivity.
  The problem is that is not wake the mouse or a key.

  I have to restart the laptop to put the image on the external monitor.
  The internal display works fine.

  It seems to me like a BIOS problem, but I have the latest version of the BIOS.
  Any ideas?

  Thank you
  Jacek

  What happens if you press the function key (Fn + F5) to change the display output? This combination activates the external monitor again?
  Have you noticed the same problem using the hibernation, or "sleep" mode?

  I m not very good if it really a laptop before issuing.
  I mean the internal display still works fine and it would be advisable to check this problem using different external monitors.

  By the way: the laptop supports Intel HD Graphics 4400. Try to install the latest Intel GPU driver:
  https://Downloadcenter.Intel.com/SearchResult.aspx?lang=eng&ProdId=3719

• Tecra Z50-A-11V: new SSD but earn 8.1 does not detect

  We bought a M550 Crucial 256 GB drive and you want to replace in a Toshiba Tecra Z50 - Av1

  We don't want to make any transfer of data or cloned.
  We want to do a clean install with Windows 8.1
  The BIOS recognizes the SSD

  But when you install Windows 8.1 doesn't detect any disk connected to the device and asked additional drivers. Windows does not detect the drive

  https://www.dropbox.com/s/mlvk6v3lxzi1rrh/2014-05-04%2009.47.18.jpg
  https://www.dropbox.com/s/fr2eo5l9xonaoln/2014-05-04%2009.48.59.jpg
  https://www.dropbox.com/s/8usxog8wm06funr/2014-05-04%2010.06.09.jpg

  I have also tested with version lasted this driver (old F6 to start to locate the hard disk driver)

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=23496&lang=eng&wapk w = f6flpy-x 64.zip

  and with toshiba package
  http://support.Toshiba.com/support/viewContentDetail?ContentId=4004211
  You can see that I have the version 3.20 BIOS. Interestingly, I see that the last one is the Toshiba has released version 3.1

  But still the CRUCIAL drive is not recognized by the instalation of windows startup

  The problem is similar with ubunto, kubuntu,... the drive is detected by the BIOS, but not for the OS.

  any help?
  Thank you

  Hello

  You solved this problem?
  Could you install system 8.1 Windows on this SSD drive?

  I think that the installation of additional drivers during the setting procedure isn't necessary since Win 8.1 should already contain pilots essential.
  From my point of view of the few, there could be a compatibility issue (maybe the SSD firmware update could solve that problem).

  What another SSD disk usage? You have the same problem with other SSDS from other manufacturers?

  Your comments would be appreciated.

• Tecra Z50-A-169 - impossible to reinstall WiDi running Win7 64 bit

  I got WiDi running, but it crashed the Tecra Z50-A-169
  It is not possible, that I do not understand why of resettlement.

  Registry may be damaged.
  Try to do a restore of the system in a week or two.
  Or try a registry cleaner like CCleaner.

• Tecra Z50-A-180 does not start using the new SSD OCZ Vertex 460

  Hello

  I bought an SSD OCZ Vertex 460 for Tecra Z50-A-180 but the system only started only not with this device.

  BIOS detect SSD but not find any system start-up.

  I cloned the old SSD HARD drive, but the system does not boot with SSD.

  I installed the firmware 1.03 on OCZ.

  I await response.

  Thank you to

  What program did you use to clone?
  Maybe it's not compatible with the version of Windows.

  If you load a new copy of Windows or Ubuntu on the SSD can it start?

• Supervisor of unlocking Tecra Z50 - A - 16 d/remove password

  Hello

  Last week, I bought a new Tecra Z50 - A - 16 d and I set a supervisor password. Now, I can not access the bios, because I can't unlock it.
  What is the key to unlock or remove the supervisor password? I read in the user's guide and google it, but he found nothing. In password utility I can put only a user password, but not of supervisor.

  Thanks in advance!

  Posted by theatre
  

  Hello

  Last week, I bought a new Tecra Z50 - A - 16 d and I set a supervisor password. Now, I can not access the bios, because I can't unlock it.
  What is the key to unlock or remove the supervisor password? I read in the user's guide and google it, but he found nothing. In password utility I can put only a user password, but not of supervisor.

  Thanks in advance!

  I too have same question I know what I set it I just do not know how to remove/disable supervisor? I use the Satellite Pro R50 - B - 12 p and I have 10 of them with supervisor defined using the same password.

  Kind regards
  Kye

• Tecra Z50 - A can't see the mobile broadband network

  8.1 Windows does not recognize the Sierra LTE mobile braodband on my Tecra Z50.-a.
  There is no software on the Toshiba support site. Observer of Sierra drivers or AirCard.

  He can't see the material in my equipment manager.
  Can't see the mobile broadband in the network domain.

  Need help!

  Thx a lot

  Can you please send full model of your laptop Tecra name?
  By the way: do you use the original pre-installed OS that you got with your laptop?

• Tecra Z50 - A - not available for downloading latest drivers

  I use TEMPRO to receive notifications on updates of driver for my Tecra Z50 - A (Windows 7-64 bit).
  But every notification contains download links pointing to the file wrong driver.

  For example, by using the following notification:

  http://www.Toshiba.EU/innovation/Dow...N=v3.3&build=5

  the driver which can be downloaded is over 1 year (http://support1.toshiba-tro.de/tedd-...0410120234.zip) and not as described in the notification.

  Also note that the same problem going on research drivers directly from:
  http://www.Toshiba.EU/innovation/Dow...ivers_bios.jsp

  So for me there is no possibility of updating my laptop.

  Thank you for your support.

  See you soon.

  Drivers using the following Toshiba official page cannot be downloaded because URL locates the old files:
  http://www.toshiba.eu/innovation/dow...ivers_bios.jsp .

  For example:
  http://www.Toshiba.EU/innovation/Dow...N=v3.3&build=5

  Please fix the download links or offer another way to update.
  Thank you.