Telepresence MCU - Port vs Adhoc Conferencing booking

Similar Questions

• Monitoring the use of telepresence MCU ports

  Hi people,

  I have a MCU4501 with 12-port HD. I wonder what a way to monitor the use of ports?

  Thank you

  Chenzhe

  See this thread: mcu-5320-port-use-report

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Configuration of the firewall Cisco Telepresence MCU 5320

  Hi all.

  I searched all the documents of the MCU again, but I found nothing on the ports it uses.

  Help me

  HI Sandra.  The 5320 MCU is the same as 4500 MCU.

  Incoming ports

  • FTP - TCP:21 + transient (dynamic rather than fixed) used TCP ports for passive mode
  • HTTP - TCP:80
  • HTTPS - TCP:443
  • H.323 - TCP:1720 + ephemeral TCP ports for incoming calls
  • SNMP - UDP:161
  • Outgoing calls to H.323 involve ephemeral ports TCP connections TCP TCP:1720 and a certain number of ephemeral TCP ports
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5060
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5061
  • Outgoing interruptions SNMP are sent the ephemeral ports UDP Port 162
  • Media (including audio and video, FECC messages) are ephemeral ports from ephemeral ports UDP.
  • The products acquired Cisco TANDBERG/Codian and gateway series series Cisco TelePresence allocate the ephemeral ports between 49152 to 65535 *. It is possible to change the ports on which these products receive and establish connections. For example, by default the Codian products Cisco acquired listen port 1720 H.323 calls and connections to port 80 web browser, but these can be modified (go to network > Services).

  Keep in mind this MCU does not support the streaming or conference me and have either the GK aboard.  If these ports are listed.

  The link to the Article can be found here:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/articles/conferencing_products_conferenceme_ports_used_kb_3.shtml

  VR

  Patrick

• Console 3515 MCU Port problem

  There is an old video conferencing MCU 3515, and I can't use the serial port to access him. When I connect the console cable to the serial port 9600/8/No/1/none affecting the Terminal application, there is no answer. I remember that we must use a special cable to access the MCU 3515 serial console. Does anyone have an idea?

  HELLO Cheng.

  You will find the layout of the pins in Tunis:

  http://www.Cisco.com/en/us/docs/video/CUVC/5_0/MCU/3515/Administration/Guide/cables.html

  Frequency settings looks ok:

  http://www.Cisco.com/en/us/docs/video/CUVC/5_0/MCU/3515/Administration/Guide/tshoot.html

  Also check that your terminal program works properly and that you are using the serial port on the right.

  Cheng: Please note the answers and set the thread if it's an answer!

• Cisco TelePresence MCU disconnects a session IP

  Now I have a MCU 4220, two VCS (neighbouring) and a version endpoint MXP 95. MCU is 4.3, and the version of VCS is X5.2.MCU are recorded in a vcs and 95 MXP is recorded in other vcs. Two VCS are nearby. Now MCU makes a call with MXP 95, but after a minute or so, MCU drops the call. I tried several times, and the situation is the same. The message to MCU I founded is "h.245 network connection error". I checked the network, everything is OK. I took an another MCU 4505 to test. Nothing wrong happene and the call can work well.

  Please give me some advice.

  Thank you.

  Hi do you have a firewall on your network where traffic can be? See you on your video mxp for this minute?

  / Magnus

  Sent by Cisco Support technique iPhone App

• Mac Book Pro, outdoor WiFi antennas work to extend wi - fi range when plugged into USB PORTS

  Outdoor WIFI antennas work if plugged into the USB port on the Mac Book Pro. If they do, those who extend range of transmission and reception wi - fi?

  Sorry, but I've never used an external USB wifi antenna but if you describe your use case a wifi Repeater/Extender can be a good option for you. https://www.repeaterstore.com/pages/WiFi-booster-Repeater-Extender-differences

  If the option is not a Repeater/Extender so will have to wait for someone who has used an external USB antenna down to.

• Telepresence using PVDM3 instead of standalone MCU

  Hello

  Can anyone advise what will be limited if we use PVDM3 ISRG2 router as a multitouch device instead autonomous telepresence MCU.

  Also we prefer to use CUCM v9.x to VCS.

  Materials will be used:

  1 CUCMBE v9.x

  2 PVDM3-256 (Qty: 2) on 2951 ISRG2

  3 CTS-MX300-55-K9 (Qty: 4)

  4 CTS-EX90-K9 (Qty: 4)

  5 cisco 99971 phones.

  Any valuable advice would be much appreciated

  BR, Shimjid.

  No it's not. There is no control of the layout or floor.

  Please remember useful frequency responses and identify useful or correct answers.

• The MCU 5320 Port usage report

  Is there a report that I can run to study the historical use of 5320 MCU ports including overall use?

  If you use one of the latest vesion of TMS, then Yes, you can - see report > use of Bridge.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• port of uplink on the booking page

  We can define the uplink port on the vRA booking page.

  

  1 is based over there?

  2. I think that the virtual machine is linked to the port group not the rising, correct link port?

  The reserves will display all exchanges that the user set in the endpoint identification information can be seen.

  You want only VM provisioning to trade, I would be avoiding the uplinks.

  Grant

• Cisco 4205 MCU and 5320 waterfall or any other alternative?

  There are 2 ports of microcontrollers 5320 (4.5) and (4.4) 4205 offering documents multimedia 16 and 12. I need to work together as an mcu with 28 or ports available max. Can anyone describe how can I do this?

  http://www.Cisco.com/c/en/us/support/docs/conferencing/Telepresence-MCU-...

  It's that this article may be the solution to my problem?

  Hello

  In your case use MCU 5320 (MCU1) as master and will act as a gateway for the 4205 MCU (MCU2) since no feature of the H323 gateway configuration and no guard integrated for series 5300 MCU.

  Kind regards

  ACE

• Two mcu 4205 cluster?

  Two mcu 4205 (4.4) with the same software both have 12 media port, now I have to make them work together as an mcu and 12 multimedia ports, have also the active guard and can be composed of devices or conferences by identification number, also I need if one of them is toward the bottom of the can function as main mcu and conferences continue

  How can I get there?

  Grouping/stacking of the MCU is not supported for 4200 series or 4500 to two MCU operate together as one.

  Clustering/stacking is supported only for the 5300 MCU series. You can only cluster/stack two units of the MCU.

  The idea of clustering/stacking the MCU is to increase capacity. The cluster will provide the sum of the capacities of the individual units. For example, if group you two microcontrollers that each supports 10 ports x 1080 p you supported a cluster which takes 20 ports x 1080 p.

  Optionally you can mount your two cascading 4205 microcontrollers:

  http://www.Cisco.com/c/en/us/support/docs/conferencing/Telepresence-MCU-4505/118763-config-MCU-00.html

  Another solution is that you need a Cisco conductor who works with VCS/CUCM.

  Take a look at these links for more information about deploying Cisco conductor:

  http://www.Cisco.com/c/en/us/products/collateral/conferencing/Telepresence-conductor/data_sheet_c78-709046.html?CacheMode=refresh

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/conductor/config_guide/XC3-0_docs/Telepresence-conductor-Cisco-VCs-B2BUA-deployment-guide-XC3-0.PDF

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/conductor/config_guide/XC3-0_docs/Telepresence-conductor-unified-cm-deployment-guide-XC3-0.PDF

  Kind regards

  Acevirgil

• Conductor create no MCU conference

  Deployment:

   CUCM 10.5 MCU5310 4.5 Conductor XC3.0.2

  I have a CUCM - conductor - MCU deployment and I am trying to set up the Conference date. I can call from end to bridge conference and point, by a busy year and the conductor I see the following:

   2015-03-02T17:27:02+01:00 conferencefactory.controller: Level="INFO" Event="An incoming call request has been rejected because the conference is not present." Conference_name="991115.my.meeting.alias" Destination-alias="[email protected]/* */" Detail="Can not create a scheduled conference. Scheduler must create conference before it can be used" Requester_(VCS/Unified_CM/client)_address="10.10.10.6" Source_protocol="SIP" Unauthenticated_source_aliases="[[email protected]/* */]" UTCTime="2015-03-02 16:27:02,99" 

  I see on the call history

   B2BUA rejected call on the Ingress with 486 Busy Here (Policy lookup response)

  On Journal MCU and Traces SIP I see nothing new, but on the driver of the Conference Bridge status is fine

   MCU (No description available); TelePresence MCU Enabled, Active. Utilisation: 0%

  No idea what could be the problem? i thing conductor to MCU something isn't good.

  Your question would be more place in the section of telepresence to the forums where these devices are more actively discussed in the conferences section you have posted in.  You can move your discussion by editing your message and change the categories at the bottom.

  It seems that you have either the Conference alias or the defined template to not allow incoming calls create the Conference, which means that only a planning as TMS application can create the Conference using the API of a conductor.

  Check the following in the conductor

  • Conference models > [model] > at the request of conference
  • Conference alias > [aliases] > Conference to create

  Also, sometimes people forget to have encryption enabled on the MCU and configured the MCU for the driver to use port 5061.  Which can also cause the Conference to fail.

• Tandberg MCU 5300 series supports the Conference me the feature?

  Hi all

  I would like to know that the 5300 Tandberg MCU series supports the Conference me the feature?

  We checked the 5320 MCU data sheet,

  Cisco TelePresence MCU 5320 CTI-5320-MCU-K9

  Comes with: 5320 - MCU and cables - MCU ports must be enabled with optional port licenses

  Software for Cisco TelePresence MCU 5320 license options

  1 nHD full HD/2 HD/4 SD/8 ports on 5320 MCU (max 10 with this option (6 used for nHD)) LIC-5300-4PL

  Second option Ethernet port (VFO) for the MCU 5320 LIC-5300-VFO

  AES and HTTPS option for the MCU 5320 LIC-AESMCU53-K9

  However, there is no information related to Conference me function.

  So, can we know everything that Tandberg MCU 5300 series supports the Conference me the feature?

  Best regards

  Ben

  Hi Ben,

  Conference is not compatible with the MCU 5300 series.

  Best regards

  Markus

  Sent by Cisco Support technique iPad App

• Video loading on 5310 MCU (via XML - RPC)

  Hello.

  I am trying to create a script for Nagios monitoring monitor the use of the video ports on my 5310 MCU (software version 4.4).

  I found an example of a perl using RPC::XML scipt and it works quiet well except for one thing: I have no video support.

  I used the "device.health.query" method, which should include a member named "videoLoad" (an allusion to Cisco TelePresence MCU API 2.10 Guide).

  I get a correct result of this method, but there are some missing members.

  Here is the result:

  rtcBatteryStatus

  Ok

  operationalStatus

  assets

  voltagesStatusWorst

  Ok

  fanStatusWorst

  Ok

  temperatureStatusWorst

  Ok

  temperatureStatus

  Ok

  mediaLoad

  1

  voltagesStatus

  Ok

  fanStatus

  Ok

  cpuLoad

  0

  rtcBatteryStatusWorst

  Ok

  There is no «videoLoad» Member

  Is that what I got wrong, or do I have to activate something on the MCU?

  Is there another way to get the load of the video of the MCU (such as SNMP or sth)?

  Kind regards

  Sven Lindeke

  HELLO Sven.  Thus, it seems that the platform of the 5300 series will not return these values as the old platforms.  VideoLoad and audioLoad return values have been deleted because they were reporting incorrect information from this platform works mixed audio and video DSP unlike older models of MCU.

  The only options I see here:

  (1) run a script to extract the status data > conferences page.
  (2) to invest in the conductor and request a conductor for audio and video ports in use.
  (3) account team push to drive above CDETS for call API to draw the status information > conferences page.
  (4) put in place a script to subscribe to and then listen to the events of feedback - see page 18 of the http://www.cisco.com/en/US/docs/telepresence/infrastructure/mcu/api_guide/MCU_API_2-10.pdf
  May be able to count participants join and leave this way maybe.

  I know that doesn't help you now, but only four methods I can recommend at this time.

  VR
  Patrick

• Need to monitor the media port use on 8510

  Info on MCU:

  Cisco TelePresence MCU MSE 8510

  Serial number SM021XXX

  Software version 4.4 (3.49)

  Build 6.18 (3.49)

  Availability 6 days, 22 hours, 15 minutes

  It is a HD blade that is configured for the ports of 40 media

  I have to be able to look at the use of the port over time to know when we have exceeded the maximum number of ports and the appellant has been abandoned to the audio only

  Thoughts?

  --

  Dan

  You can find exactly what you are looking for in the event logs.  I just maxed out our 8510 by a participant, the same fall first one I added in the test that matched my allocation of port instead of going 1-sending video of my test results are below.

  30330	17:40:09.423	CONFERENCE	Info	Unable to send the video to "Patrick Sparkman" - allocation exceeded
  30331	17:40:09.536	CONFERENCE	Info	now able to send the video extended to "Patrick Sparkman"