Console 3515 MCU Port problem

Similar Questions

• EM port problem

  Having a problem with EM on a test system I played with that.

  11 GR 2 (11.2.0.4) on SLES 11 SP3

  The listener has changed in 1522, after having been initially setup. I can connect via SQL on 1522 (with SSL), but console EM still watch port 1521 and think that the DB is declining because it cannot connect to 1521.

  OK, noted a SR with Oracle. Turns out that EM using TCP/IP over SSL is not yet supported (I was told its a question they are actively working on). Only option was to create a 2nd listener (auditeur1) using TCPIP and we can start it and stop it when we need to access the EM.

• charge port problem

  Hey guys I use an Iphone 5 16 GB and, recently, I found that my charger is not working properly so I change the cable and the problem is still there.

  My iphone does not load, BUT when I put a small piece of paper or something like that under the "cable plug" (sorry I don't know what to call it) and it works perfectly.

  So my question is: is it possible to fix this? Or can I replace the charger port?

  Hello, it seems that your charger port is broke off or a cable lost the appropriate connection. Your charger to another iPhone, try to find what is the problem. If it works fine with another iPhone, which means that your device needs to fix the charger port. In this case, it is best to take it to the service of Apple.

• Bluetooth Windows 7 USB port problem

  Hello

  I use a bluetooth class 1 dongle (manufacturer unknown) with the V 8.00.03 Premium toshiba bluetooth stack and a bluetooth headset. The specifications for the dongle are: Bluetooth V1.2, compatible USB V1.2/2.0

  I have a strange problem when changing the USB dongle is plugged. If I change the dongle on another USB port, searching for devices fails. I tried to uninstall the battery and of course remove device from the bluetooth Manager window.

  Also, strangely, when I plug the dongle on a USB extension on the same port, it does not either. When I put the dongle into the same USB port it works fine as usual.

  I want to change the USB port so that I can get the best reception, like its plugged in to the back at the moment. Also, I want to use the usb expansion for the same reason, to bring out above the office. Oddly, if, as I say, it does not work with the extension (just a regular cable with USB male on one end and female on the other to plug the dongle in.)

  Is this something to do with voltage drop down a cable? And regarding the change of the ports usb is it something to do with ports being installed on this USB port bluetooth only? I don't know exactly how ports bluetooth works, how they settle etc.

  Thanks much for any help.

  Hello

  > Also, strangely, when I plug the dongle on a USB extension on the same port, it does not either. When I put the dongle into the same USB port it works fine as usual.

  I think you're wrong here buddy
  If you use another manufacturer's computer, and if you have problems using it, you should check the page of computer manufacturing support.

  In my opinion the question isn t linked to Toshiba BT stack but to the USB ports on your computer.

• On Satellite Pro A300-13Y USB port problem

  I have a Satellite Pro A300-13Y with 4 USB ports. The USB ports of two right don t work. I bought this phone recently (2-3 weeks ago). It has a Windows Vista Business SP1 on it. I put chip in utility installed on it, I checked the Device Manager and tried to find driver for it but I couldn't solve this problem.

  So I called Toshiba service dek, they say that I need to install new standard to factory install to see if it can be solved. But I don t find it the best way and I have some applications installed on it and get some info on my laptop, so I would find another way to solve this problem.

  Also, I think it might be a hardware problem. Can someone show the way in which I can find or fix this? I can also send it to guarantee, but I made a mistake and if there is not a hardware problem that I have to pay for it.

  Hello

  I know it s not the best way, but it's the only way to exclude a hardware failure. If after a recovery of the won´t of USB ports not work then you can send it to repair without being in doubt that they will charge you for the repair.

  Welcome them

• Material RANE/Serato SL2 SL3 SL4 Core Audio Port problem with El Capitan

  Hi Apple,

  I and many others have had problems when using devices with Rane Serato DJ software where the breaks down of software, nor will we get audio drop-outs and crashes.
  (Audio Interface) device that I use is RANE SL3.

  MacBook Pro (retina, 13 inches, end of 2013)

  Version: 10.11.2 (15 c 50)

  Intel Core i7 2.8 GHz

  16 GB 1600 MHz DDR3

  Iris 1536 MB Intel

  1 TB SSD

  Serato have updated their software (1.8.1) to take in charge the last OX El Capitan (10.11.2) and announced that the problem is with the drivers of RANE and Serato not.

  See Site for more information: https://support.serato.com/hc/en-us/articles/213821528

  RANE said its now a problem with Apple and is a Port Audio problem. Please see their announcement about the update of BEEF: http://dj.rane.com/support/knowledge-base/el-capitan-update

  This is the Forum for discussion with RANE, saying they are awaiting your response on fixing this problem.

  here: http://dj.rane.com/support/knowledge-base/el-capitan-update

  Rane suggested only that downgrade us our BONES to the Mavericks or Yosemite. This should not be the case!

  We need answers, and for not having spent somebody else as everyone pushes the blame.

  Please you can find what the solution is rather then downgraded to a previous operating system. It's a very frustrating with all the people who spent loads of money on a Macbook and RANE hardware especially this time of the year where we DJs play every weekend like our jobs.

  Hope this gets sorted soon
  Concerning
  Anthony

  This is a user forum. While we, users can sympathize, is not in our power to resolve this issue if it's a bug.

  To allow Apple to know of this problem, you must use the appropriate feedback chanel.

  http://www.Apple.com/feedback/

• Visa set up serial port problem

  Hi all

  I use the RS-232 port to communicate with the instrument. At the moment the device is not their so I shorted pins 2 and 3 of the connector connected to the COM2 port, so that what ever I'm transmitting, I I'll be back. Using Hyperterminal I am able to verify that whatever i write, he's coming back.

  But when you use a Labview 7.1 I am tring to connect first by configuring the using VISA CONFIGURE SERIAL PORT.vi serial bus

  with the following parameters

  Visa resource name = ASRL2::INSTR (port COM2 because)

  Baud rate = 2400

  Data bits = 8

  Parity = None

  Stop bits = 1.0(Equal to 10)

  Flow control = None

  End of reading at the end of character = True

  Dismissal = A

  Up VISA is in error. The error code is 1073807202

  The procedure described above is similar in the read/write of Visa examples provided...

  I strive to solve the problem but all invain.

  Can anyone help me in this.

  See here

  I guess your problem is #2 (you have not installed OR visa).

• Serial Port problems - carriage return and use as an executable file

  Hello

  I developed an application to send a few simple commands on the serial port and read the corresponding answers of a device that I am in communication with.  I have been using logical Port to watch the line TX of the serial port.

  By using the Visa configure Serial Port I set the stop character property allow true and used the hexadecimal value D trying to make the termination a carriage return characters.  When I sent the order, I'll send the cmd followed by Enter.  No matter if this property is set to true or the hexadecimal value is set to D for carriage return or line break is, the serial port would always send a line break.

  Then I got crafty and the string constant under normal display to hexadecimal display.  The ONLY way I could send a carriage return was manually putting 0x0D after ordering.  So my question is, why the Visa set up the Serial Port is not working correctly, and is there a better way to send a carriage return?

  My next issue is facing the construction of executable files.  I'm using LabVIEW 8.2 and wrote this program for another employee to use on his laptop computer.  I did install runtime Labview 8.2 and led to the executable that I generated.  I did-> the executable by clicking Tools build the executable.  The problem I noticed was that the executable would open and will work perfectly, but it would not send any data the serial port.  I then ran the executable on my laptop (which contains the full version of LabVIEW 8.2) and the serial port has worked well.  I guess my question is... Are there plug-ins that must be installed to use the serial port with the Labview runtime engine?  Or y at - it a step that I failed to do?

  Thank you

  Gary Still

  Not immerse in the first issue. The Knight will probably be galloping until shortly.

  For your second question, after building the executable, you must build the installer and includes support for the VISA. VISA is required for serial communication, and it does not accept American Express.

  It may be useful

  -AK2DM

• W510 usb ports problem

  Hi all

  I have a W510 machine which has 4 usb ports, including 2 3.0 ones (blue marker), 1 still active (marked in yellow) and usb-eSata port a combo. They are all works well with data transfer, but I'm not sure that they do with the power supply matter. The use of two 3.0 ports seem to feed all the time, except when the laptop is turned off (say, my short of cooler for laptop when the thinkpad goes into mode 'sleep'; or I can easily wake up my pc by moving my mouse that is connected to one of the two ports 3.0)

  The combined port seems very well, his power goes off mode "Eve" (cooler stops working when it is connected to it)

  Always on that seems odd. Power goes off like the combo, but if I plug it into a something like the receiver of my mouse wireless, the machine does not start in the next boot.

  Does anyone have problems like mine?

  Hello partner,

  Try to check in the BIOS if the always on udb is activated and in the boot order if usb is not first otherwise u may have problems to start with something to plug...

• Parallel Port problem

  We used the kind of software that uses a key lock (which is connected to the parallel port), we have added new machines in our Mt. HP3330 company, i.e, who doesn't have a parallel port on the motherboard. The problem starts here, even after installing Add on parallel port & required installation driver, after the execution of programs, it gives an error not found "Key lock". This problem can be solved using the USB parallel port?

  Even after that the installation of the Add on parallel port & installation required pilot, after execution of programs, it gives an error "Key lock" not found

  You mean you bought a discreet the snap card to provide a parallel port?

  Check Device Manager for parallel ports that are available on your PC and what is their status...

  • Click Start
  • Click on run
  • Type devmgmt.msc and press enter
  • Enlarge (click on +) Ports (COM & LPT) section

  Please answer with the information on your parallel port (printer). Is there more than one?

  If there is that this means that even though there may be no physical outlet, your motherboard has the ability to add another via a ribbon cable.

  If this is the case there are two options...

  1. Configure your software to use the new (LPT2 probably) LPT port not LPT1.
  2. Remove the add-in and replace a cable sheet of the motherboard to a backplate with a parallel decision-making. You should be able to buy this th same place you bought the card.

  Tricky

  EDIT: 3rd option if you have 2 LPT ports: disable the port of the motherboard in the BIOS, uninstalling the card and its drivers. Re-install add it in card and should be LPT1.

• Spectrum of HP - MINI DISPLAY PORT PROBLEM

  Good evening, I'm Mattia, I have a HP spectrum 13 ultrabook; It has a mini display port, as the macbook, so I bought a mini display of sample of cable vga port to connect my ultrabook to my vga monitor 19 ". The problem is no signal in the company of Eve. Is there anyone who know the cable that should work?

  The cable I buy and the seller told me it should work:

  http://www.eBay.it/ITM/320935563726?ssPageName=STRK:MEWNX:it & _trksid = p3984.m1439.l2649

  Thank you all

  ML

  It nuovo e love cavo e funziona! He first che era stato dato era rotto e! Problem solved, grazie thousand per aiuto e per i consigli

• COM PORT problems

  I have problems with a USB series adapter.  When I try to load... it says all my COM ports are "In Use" and yet I have nothing installed or activated.  How can I clear the COM Ports and release them?

  Hi RWLeawood,

  This can happen if there is some hidden devices in Device Manager may use the COM ports.

  (a) click Start > all programs > Accessories and then click command prompt.

  (b) type set devmgr_show_nonpresent_devices = 1 in the command prompt and press enter.

  (c) type cd \Windows\system32 in the command prompt, and then press enter.

  (d) type start devmgmt.msc in the command prompt and press enter.

  (e) click view >Show hidden devices. This will display devices that are not connected to your computer.

  (f) now, if you expand the section on COM ports, all the COM ports that have created everbeen will appear, no presents those being gray. You can uninstall what you don't want (right click, select Uninstall).

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• WAG200G ethernet ports problem

  Howdy,

  I have problems connecting via ethernet to my WAG200G. Everything was working fine a week ago, but now, nothing.

  The problem occurs only with a computer and tried troubleshooting on site without success.

  When I connect the ethernet cable from my computer to the modem/router, I don't get a light on the front panel on one of the ports. I have changed the cables, ports, disabled ZoneAlarm and firewalls and nothing comes up. I checked the ethernet connection from the computer to a different computer and it works fine.

  On another computer, I have no problem connecting to ports and can confirm that 1-4 work and lights.

  Any ideas? Thank you!

  Thanks for the help - after more research found is not at all a problem of Linksys, but an automatic Windows Update which is in conflict with the Realtek driver.

• USB port problem - peripheral usb not recognized for what I plug

  When any device is plugged into usb port (ipod, camera, printer, etc.). I get the message "usb device not recognize."

  All the usb drivers have been updated, but I still receive the message.

  Hello, just for your info. I ran the patch program, but it didn't really do anything but say I had a problem with something and I had to pay someone to watch. Someone I know told me that the last thing that I had loaded several days before the problem was probably the problem. The only thing that was new was Avast program, so I uninstalled. But this does not work, I still had the usb problem before and after I reinstalled it. Also, I discovered that I had a problem to interface with Avast and after repeatedly talking about them and trying hard and it doesn't work, they wanted me to use their special program program uninstall in safe mode and uninstall Avast. So I did, then I reinstalled it and it fixed the problem to interface with Avast. Then a few hours later, I tried to use my usb ports again, just for the * of it. And quess what, they worked. Yes in some way the avast program stopped my work usb ports, when I installed it first. Avast said he couldn't have their summer program? Well it works now anyway. Thank you, Greg

• U2414H, display port problem

  Hi guys, so I just bought U2414H for my rig to play with graphics card AMD Radeon MSI R9 390 8 GB memory GDDR5 512 bits with 1 DisplayPort, 1 x HDMI, 2 DVI - I. My problem is, when I connect miniDP to the monitor (which is only a miniDP) to (DisplayPort) my graphics card, AMD Radeon MSI R9 390, but it only goes to the power save mode. I can't access same monitor configuration. I already change the input source to the port of mini-affichage on the screen. but it still saying no mini display port.

  So, help me please.

  Hi Chris thanks for the reply, apparently my problem is solved, the main problem is that I plug the 2 x 6-pin power for graphics card, haha. Only, I have attached the graphics card to the motherboard.

  : D