tensioning of excitement to 0 after VI

Similar Questions

• Pavilion G6 2302 ax battery cell no. 4 tension showing o mV even after charging is complete.

  Hi guys,.

  My Pavilion g6 2302ax cell no. 4 battery voltage showing o mV even after a full charge.

  I baught my laptop 2 months before and its hardware works very well so far, I've noticed this problem. I've attached a screenshot of the HP support assistant screen. Please take a look.

  

  If anyone has an idea about this help please.

  Hello dipuab,

  Your battery test shows 0 on the fourth cell.

  There is nothing wrong with the battery, the test is designed for only three of the battery cells, test one of the tests will display 0.

  Here is a link to another post that had the same problem. Message 7 of 7.

  Hope it will be useful.

• How do I capture the output of voltage full bridge with Signal Express NI9219

  Hello.  I'm trying to do and calibrate a load cell with the installation of full-bridge strain gage.  I use a NI9219 module with a cDAQ chassis.  Is it possible to capture the actual output voltage?  Signal Express gives me a value of strain, but I really need to know the output voltage.  Where to look.  I need only two channels for full-bridge.  I think that could connect the wires to the two remaining channels and read the output voltage of the strain gauges which would be connected as a tension of the 9219 entry, but I think that Signal Express could give me the voltage and output voltage directly.  Any input would be appreciated. Thank you!  P.S. I only use this equipment on occasion and am not the more familiar with it, so keep things simple for me.  Thanks again.

  Hi jgh@AET,

  The NI 9219 measures the ratio of voltage full bridge in hardware sensors, allowing any variation of the voltage to cancel. You won't be able to measure the output voltage of the sensor regardless of the voltage without additional channels, but you can measure the ratio of raw tension using the type of Bridge (V/V) . You can also use the type of measure of Force (bridge) measurement of load cell with engineering units (N, lb, kgf, no strain).

  This screenshot shows where the two Bridge (V/V) and Force (bridge) can be selected in the DAQ Assistant:

  

  These types of measurement were added sometimes around DAQmx 9.1, so if you have an older version of NOR-DAQmx, your DAQ Assistant maybe not them. The latest version is currently 9.4 of NOR-DAQmx. Front of NOR-DAQmx 9.1, the approach to recommend to measure the load cells was to use the custom with Excitation voltage type and a custom scale. However, Tension Custom excitedly can't Bridge of calibration in the DAQ Assistant.

  Brad

• Using signal (+/-10 000 g) accelerometer

  Hi all

  I use an accelerometer for measurements of vibrations.

  The accelerometer is connected to an external excitation device to provide the excitement of the accelerometer (coupler-Kistler). The coupler is then connected with the NI SMU-6361 module which is connected to the NI PXI3-1073 chassis. Based on the gain of 1 and the excitement of voltage of +/-10V, the accelerometer can provide + / 10 000 g. I use assistant DAQ for now to see the signal and then moved to DAQmx. I chose the option of tension instead of tension with excitement and I put the settings +/-10V for max and min values of signal, CSR for Terminal configuration. I also used the option of scaling of the table for the g-10 000 to-10 V and 10 000 g for 10 V. The accelerometer does not seem to work properly as long as the signal does not change. Is it possible for the advice me what goes wrong with the configuration of acceleration it please?

  Thank you.

  How to set up the chain of coupler/measure:

  Your sensor has a sensitivty (let's say it's a constant for a given frequency range) S_ug [mV/g] and you add the coupler with a gain of G_c [V/V = 1]. so you get S_total [mV/g] = S_ug * G_c

  The acquisition of your data can read + 5V-(lire les spécifications en détail, généralement qu'ils peuvent lire jusqu'à 5.5V) and the maximum expected acceleration is?

  You can always overtemperature or increase the G_c to measure your signals in an optimum range.

  You read a voltage u (t) and g (t) = u (t) / S_total.    You can do this conversion in your program, or tell MAX / DAQmx for that already in the driver.

  You should read the manual of the hitch on the way to configure the gain or sensitivity.

  If you measure the pulses, lockout for above 10 kHz signals... you can always use the sensor (up to maybe 40-60 kHz), but some more signal processing is involved in this case and make an FFT on the signal. (or a higher uncertaincy)

  If you have the functions of transfer of the probe and the coupler, you can convert your signal in frequency domain, compensate for the functions of transfer and convert bach in time domain, to get a better estinate of your acceleration.

• Problems with 2.1 update

  I got the email address of the upgrade and was more than excited, but now, after, I wish that I had just stayed with my 1.4.8.

  I tried a factory reset and reduce a lot of apps, but it continues to run very slowly for me: /

  It takes me like 7 minutes just to open a text message and answer to the back and a good 5 just to make a call phone o_O.

  Am I the only one having this problem?

  I know this is just a beta version, but that Vibrant is really calling my name and I am very close to just buy it and say forget the Cliq /:

  I begin to think that it is the phone myself. Sorry, but it looks like you need a replacement phone.

• NTVDM.exe is suspended.

  Windows XP Pro SP3.
  NTVDM.exe has suddenly stopped working if I run cmd.exe or command.com.  No error message, no prompt, just a blinking cursor.  If I run cmd.exe orders BACK internal DIR & CD work fine, but when I try to run one of my programs ntvdm.exe BACK starts and crashes.  When I run command.com ntvdm.exe starts immediately and crashes.

  It started when I installed a trial version of Nero 9 CD burner.  I discovered this problem and uninstalled Nero 9 about 2 hours later, but the problem persists.  The crew of Nero tech support had me do a scan and send it to them, but concluded that it did nothing to my computer to cause this problem.  I noticed that I have an empty folder named WindowsPowerShell in the windows\system32 directory, but I don't know if it's there before installing Nero 9.  I never used it.  I also noticed that there are no dosx.exe in the windows\system\32 directory.  I copied the \dllcache folder and that made no difference.  Seven weeks to research on the net has produced nothing.  I discovered yesterday the Process Monitor from Sysinternals and installed.  Exciting program!  After scanning through thousands of lines of events after ntvdm.exe begins until it crashes, several times, the only thing I found is an 'access denied' something done ntvdm.exe.  I don't remember the details.  None of the missing files.

  It drives me crazy!  You can provide any help will be greatly appreciated!

  Windows XP Pro SP3.
  NTVDM.exe has suddenly stopped working if I run cmd.exe or command.com.  No error message, no prompt, just a blinking cursor.  If I run cmd.exe orders BACK internal DIR & CD work fine, but when I try to run one of my programs ntvdm.exe BACK starts and crashes.  When I run command.com ntvdm.exe starts immediately and crashes.

  It started when I installed a trial version of Nero 9 CD burner.  I discovered this problem and uninstalled Nero 9 about 2 hours later, but the problem persists.  The crew of Nero tech support had me do a scan and send it to them, but concluded that it did nothing to my computer to cause this problem.  I noticed that I have an empty folder named WindowsPowerShell in the windows\system32 directory, but I don't know if it's there before installing Nero 9.  I never used it.  I also noticed that there are no dosx.exe in the windows\system\32 directory.  I copied the \dllcache folder and that made no difference.  Seven weeks to research on the net has produced nothing.  I discovered yesterday the Process Monitor from Sysinternals and installed.  Exciting program!  After scanning through thousands of lines of events after ntvdm.exe begins until it crashes, several times, the only thing I found is an 'access denied' something done ntvdm.exe.  I don't remember the details.  None of the missing files.

  It drives me crazy!  You can provide any help will be greatly appreciated!

  U have already repaired components of the help system
  sfc/scannow

• Record will turn off by itself

  I have a Sansa Clip + 4 GB and like it a lot.  He plays very well and when he records it superbly.

  However, when I want to record a class, I start recording, put it in reverse so that the microphone is pointing towards the sound source.

  I come back later and find the turned entire drive, and when I go to play the record, it's a few minutes of time, while the class was an hour of time.

  I'm doing something wrong?

  You can sleep under tension, so it turns off after a certain period of time?

  You have enough free space (memory) to record for the hour? These things recorded in WAV format, so they use a lot of memory for recording space.

• Aurora

  My beautiful ladies and gentlemen, I bought an alienware last year. I was so excited. Then after 8 hours it stop working. Called and after 5 transfers of phone, I finally got a Dell technician certified in my house, but alas, he couldn't fix it. So I called Dell again and after 13 phone transfers and 2-1/2 hours on the phone, I hung up. I had my wife, who is a certified Dell technician, call them up and after 9 phone transfers and two hours, she is my money back. They refused to replace the computer, instead, just handed my money. It's a weird business model. Thank you for your time Fat Tony

  buddymarange

  Glad to hear that Dell will refund your money.

  Bev.

• 'Connections' blackBerry smartphones on... But no emails come through

  I can't receive new e-mail messages even though many came via Outlook. I tried the following:

  • Perform a Soft Reset
  • Performed a Hard Reset
  • Go to 'Manage connections' and all the connections off tension, then back again.  After shooting it back on once again, the Mobile network has a check box to the left of it and a green check mark on the right.

  I see several bars in the upper left corner which lead me to believe that wireless is enabled.

  The story is that I left the blackberry in my car to charge overnight.  When I'm in my car at midday, it appeared that I had received messages until 09:00 this morning, and then it suddenly stopped.

  I have no idea what's going on and I scoured these pages to try to find a solution, but none seems to fit this Bill. Any help would be greatly appreciated... Thank you!

  have youe besadmin send you service directories

• Excite AT10-A-104 error after factory reset

  Hello

  I have reset my Tablet: excite AT10-A-104 to the factory setting (I bought the unit in 10.2014).
  The process has completed correctly and update proceeded correctly.
  Tablet starts correctly but after 30 sek. He starts the long inscription of the device with the error: device Toshiba App Instaler recording: "the software updates check error".

  The same situations when I use applications: Toshiba App manager: "network without an available internet connection error. Connect to Internet, and then try again to update your software.

  My internet connection is OK.

  Thanks for your help!

  I have exactly the same problem, can not see the answers, have you sorted and how? Thank you

• Excite Pro - problem of WLan authentication after 4.3 update

  Hello

  I have a Pro excite, and today I did all the updates that where possible to the Toshiba service station.
  The last update Idid was the 4.2 to 4.3.

  After this update, it is not possible to connect to my Wifi.
  Authentication problem...

  I tried all of them, with or without WPS restarting the Tablet and the router...
  Before this update, it was no problem to connect with WiFi.

  What can I do?

  You can try to reset the Android system to factory settings and might try to reconfigure the wireless network.

  I found this recommendation in one of the discussions of the forum:

  + The reset process will erase all data, settings and apps on your tablet. You must have a backup of any data you want to keep before proceeding. +

  + 1. Make sure the Tablet is turned off and not in sleep mode. +
  + 2. Hold the volume and Power buttons simultaneously until the two Android icons appear. +
  + 3. Use the volume buttons to select the white box to the right. +
  + 4. Once selected, press the power button. +
  + 5. Use the volume keys to select wipe cache partition, and then press the power button. +
  + 6. Select Yes, and then press the power button. +
  + 7. Use the volume keys to select wipe data / factory reset and press the power button. +
  + 8. Select Yes, and then press the power button. +
  + 9. The tablet will reset now. +

• Excite PRO 3G connection does not work after last update Android v4.3

  Hello

  I live in Italy and last Sunday (26 January) my excited PRO Tablet (model AT10LE - A - 10 H) received version Android 4.3.201121220.35.

  After restart my wifi works fine, all other app very well work, but my 3g connection does not work, mobile bar is empty and it says "no service".

  My sim card is ok. I used this sim card before the system update and I don't have a problem with Android 4.2.2.

  Please help me.
  Thank you

  > After reboot my wifi works fine, all other app very well work, but my 3g connection does not work, mobile bar is empty and it says "no service".

  Go to mobile network settings and search again for the 3G network.
  I had a similar problem with my Android Smartphone and my o2 provider
  I started to search for new, so I chose the O2 again and then I could solve the problem.

  In the case where this does not work for you, recommend you to reset the default Tablet (factory settings)

• How to filter the traces of tension TDMS after acquisition?

  Simple question. We have acquired a lot of electrophysiological data with express signal. We now need to filter data after the acquisition for later analysis. I can import the files TDMS tension of previous experiences, but can't seem to run the filters we used on the side of the acquisition to filter the existing traces. Is there a simple way to do this?

  -smb

  Hello Chinchilla,

  I enclose a few screenshots on how to add a step to an analog input filtering. You can select the type of filter and order too.

  

  In this screenshot you can check how to change the configuration of the filter

  

  Finally, you can access the TDMS of LabVIEW file with one of the examples of PDM. Please follow these instructions:

  1. open LabVIEW

  2 - go to help > find examples to open the Finder 'example '.

  3 - Go to Fundamentals > file Input and Output > TDMS > Standard Read and Write and select the VI named TDMS read Events.vi

  

  You will need to know the data present in the file to read correctly. For this, you can use the leading PDM Viewer VI:

  http://zone.NI.com/reference/en-XX/help/371361K-01/Glang/tdms_file_viewer/

  Or you can use the Toolbox for excel: http://www.ni.com/example/27944/en/ (allows you to transfer the data to Microsoft Excel).

  4. After reviewing the data, you will need to apply a filter. You can find the filter functions in the range of Signal Processing.

  

  Please let me know if you have any questions on this subject.

  Kind regards

• Excite Pro AT10LE-A-108: after JB 4.3 external BT keyboard upgrade does not work

  Hi all!

  After update 4.2 JB JB 4.3 does not work my bluetooth keyboard.

  Pair ok, Tablet keyboard sees but does not.
  Please, do toshiba repair package or fix problem.

  On the other my android device (phone LG with 4.1.2) working this keyboard ok.

  Sorry, my English is very bad. (Google Translator)

  Thank you.

  [Keyboard Type | http://www.trust.com/en/all-products/18441-executive-folio-stand-with-bluetooth-keyboard-for-ipad]

  Okay, please, I want to downgrade 4.2 JB for this tablet, it's possible?

• Toshiba EXCITE Pro - WiFi. Authentication failed after update

  Hello.

  Just got this tablet.
  Everything seemed ok by updating to the latest version (because first of all to solve the problems of heat).

  After the update * I lost my WIfi connection. Failed authentication * (has not changed anything - linked - update ok 1 minute before the last update).

  After that I started to not test, Wps, Wifi etc etc security connection
  * Finally, at a random time (and with the original settings) I logged in *. After that I closed the Tablet the same problem occurred.

  After doing the same things again once I finally logged and this time it seems to be ok, even though I stopped the tablet.

  However, it's frustrating.
  Maybe you have to address this issue?
  I have seen and others return this tablet after having this problem.

  It is not a hardware problem since its correct operation before the update.
  Of course tried factory reset twice.

  Hope, I don't have this problem again, * but I inform in the hope that fix you this in a future update.*

  Hello

  Go to your wifi settings - forget your network - connect again with your code

  Normally after that he has to work again.

  Concerning

  Post edited by: Fulgore