test ports

Similar Questions

• E4200 last v1 FW, unable to get port 80 to port forward

  I try to configure mycloud.   I got it everything works fine until I updated to the: 1.0.06 FW of the FW.05

  When I test port 80 with http://www.yougetsignal.com/tools/open-ports/ I get the messaged that the port is CLOSED.   I have forwarded all ports, work very well. Except wich 80 my my NAS account

  the only thing I have not done is to reset the router.  It's a pain in the but.  I have 6 cameras Wifi on all there with remote access to my iPhone ect...

  Thanks for your help.

  I fixed it... I started 05 FW... this router is a joke.

• Impossible to access remotely to Zoneminder on port 80

  I have a Cisco Linksys E2500 modem and I can't access Zoneminder which is basically a Linux video security DVR software package.  It runs on a Ubuntu Linux server.

  I have HTTP port 80 forwarded to the address static IP of the server Ubuntu but I repeatedly get an error indicating that the connection has expired whenever I try to access Zoneminder remotely as in access it remotely from a coffee shop.

  I have absolutely no problem to access the Zoneminder when I on my home LAN.

  I can access other software from remote sites on the parameters of the port 4369 with a favorite TCP protocol.  In other words, 4369 port is forwarded to an another Windows workstation with a static IP address assigned. Absolutely no problem with 4369 port forwarding.

  Also, I tried port 80 on the site, YouGetSignal, which is used to test port forwarding.  The Web site indicates that port 80 is closed.  But when I test port 4369, the site indicates that the port is open.  Zoneminder that uses port 80 is fully operational when I test port 80 via YouGetsignal.

  My ISP told me that they do not block the ports including port 80.

  Any help would be greatly appreciated

  Thanx

  Try the following steps:

  [A] with the help of the Cisco Connect software (if at all, you have installed the router using this software)

  1] open the software and go to the option that says "settings of the router.

  [2] then click on the option that says 'Advanced settings', which will take you to the router configuration page.

  [3] then click on disable SPI Firewall Protection Security tab, uncheck the box filter anonymous Internet requests...

  [B] If you have not installed Cisco connect then you can connect to the router's user interface using its default IP address in the browser which is 192.168.1.1 and enter "admin" as password empty username field. This will take to the web interface of the router and then follow the steps as indicated above to make the changes.

• Port stuck

  I have a problem with a switchport on a N2048P. The port no longer works. This is my test port. The last thing I did, has been reconfigure trunk to access while it was up. After that, the port would send all traffic. I tried:

  • 6.1.2.4 to the 6.2.1.6 update (i.e. a reload)
  • from the trunk to access the generals and back to access
  • Hot-Swapping the switch hit in the stack by another

  The problem persists. The Exchange switch has the problem and kept until it has been reset to the factory settings. The output current of the switch is:

  switch#show spanning-tree gi4/0/3
  
  Port: Gi4/0/3   Enabled
  State: Forwarding                                Role: Disabled
  Port ID: 128.165                                 Port Cost: 0
  Port Fast: Yes                                   Root Protection: No
  Designated Bridge Priority: 32768                Address: F8B1.5657.4284
  Designated Port ID:   0.0                        Designated Path Cost: 0
  CST Regional Root: 80:00:F8:B1:56:57:42:84
  Root Guard..................................... False
  Loop Guard..................................... False
  TCN Guard...................................... False
  Auto Portfast.................................. True
  BPDU Filter Mode............................... Disabled
  Time Since Counters Last Cleared............... 1d12h15m9s
  BPDUs: Sent: 0, Received: 0
  
  switch#show interfaces status gi4/0/3
  
  Port      Description     Duplex Speed   Neg  Link   Flow  M  VLAN
                                                State  Ctrl
  --------- --------------- ------ ------- ---- ------ ----- -- -------------------
  Gi4/0/3                   Full   1000    Auto Up     On    A  301
  
  switch#show interfaces detail gi4/0/3
  
  Port      Description                 Duplex Speed   Neg  MTU   Admin Link
                                                                  State State
  --------- --------------------------- ------ ------- ---- ----- ----- -----
  Gi4/0/3                               Full   1000    Auto 1518  Up    Up
  
  Port      Description
  --------- ----------------------------------------------------------------------
  Gi4/0/3   
  
  Flow Control: Enabled
  
  Static configuration:
  PVID: 301
  Ingress Filtering: Enabled
  Acceptable Frame Type: Admit All
  
  Port Gi4/0/3 is statically configured to:
  
  VLAN    Name                              Egress rule
  ----    --------------------------------- -----------
  
  Forbidden VLANS:
  VLAN    Name
  ----    ---------------------------------
  
  Port Gi4/0/3 Enabled
  State: Forwarding                                Role: Disabled
  Port id: 128.165                                 Port Cost: 0
  Port Fast: Yes (Configured: yes)                 Root Protection: No
  Designated bridge Priority: 32768                Address: F8B1.5657.4284
  Designated port id:   0.0                        Designated path cost: 0
  CST Regional Root: 80:00:F8:B1:56:57:42:84       CST Port Cost: 0
  BPDUs: Sent: 0, Received: 0
  
  switch#show running-config interface gi4/0/3
  
  spanning-tree portfast
  switchport access vlan 301
  dot1x port-control force-authorized
  

  The combination of State: transfer and role: people with disabilities seems strange to me. It is interesting also, that the details of the interface is missing two lines after flow compared to a normal port control.

  Flow control: enabled
  Port: IG4/0/4
  Mode of belonging to a VLAN: Access Mode

  Any ideas on where the config is borked?

  Hi Josh,.

  It's just this port a port. As you can see in the output there is not a single bpdu sent or received on this port.

  The output of another port is:

  #show interfaces detail gi3/0/31
  
  Port      Description                 Duplex Speed   Neg  MTU   Admin Link
                                                                  State State
  --------- --------------------------- ------ ------- ---- ----- ----- -----
  Gi3/0/31                              Full   1000    Auto 1518  Up    Up
  
  Port      Description
  --------- ----------------------------------------------------------------------
  Gi3/0/31
  
  Flow Control: Enabled
  Port: Gi3/0/31
  VLAN Membership mode: Access Mode
  
  Operating parameters:
  PVID: 2
  Ingress Filtering: Enabled
  Acceptable Frame Type: Admit All
  Default Priority: 0
  GVRP status: Disabled
  Protected: Disabled
  
  Port Gi3/0/31 is member in:
  
  VLAN    Name                              Egress rule   Type
  ----    --------------------------------- -----------   --------
  2       ALT-VLAN                          Untagged      Static
  
  Static configuration:
  PVID: 2
  Ingress Filtering: Enabled
  Acceptable Frame Type: Admit All
  
  Port Gi3/0/31 is statically configured to:
  
  VLAN    Name                              Egress rule
  ----    --------------------------------- -----------
  2       ALT-VLAN                          Untagged
  
  Forbidden VLANS:
  VLAN    Name
  ----    ---------------------------------
  
  Port Gi3/0/31 Enabled
  State: Forwarding                                Role: Designated
  Port id: 128.139                                 Port Cost: 0
  Port Fast: Yes (Configured: yes)                 Root Protection: No
  Designated bridge Priority: 32768                Address: F8B1.5657.4284
  Designated port id: 128.139                      Designated path cost: 500
  CST Regional Root: 80:00:F8:B1:56:57:42:84       CST Port Cost: 0
  BPDUs: Sent: 104170, Received: 0
  

  There is no error of spanning tree in the newspaper. If you want I could you e-mail the output of the show of support.

  But I found the culpit. There was still a session from the active monitor on this port. Thanks anyway Josh.

• WampServer: Your port 80 is actually used by Microsoft-HTTPAPI/2.0

  I NOTE: WampServer has no relationship with Microsoft, but the problem has...

  Hello world

  I uninstalled WampServer 2.5 and installed WampServer 3.0 on my Windows 7 SP1,

  The WampServer icon color is orange, which means that one (Apache) service is not running.

  I used the 80 submenu test port and cmd gave me this:

  A test that uses port 80 *.

  = Put to the test by the netstat command filtered on port 80 =.

  Test TCP
  Your port 80 is used by a process of PID = 4
  The process of PID 4 is 'System' Session: Services
  The PID 4 service 'System' is "N/a".
  ERROR * this service ISN'T Wampserver - should be: "wampapache;

  Test for TCPv6
  Your port 80 is used by a process of PID = 4
  The process of PID 4 is 'System' Session: Services
  The PID 4 service 'System' is "N/a".
  ERROR * this service ISN'T Wampserver - should be: "wampapache;

  = Tested by attempting to open a socket on port 80 =.

  In fact, your port 80 is used by:

  Server: Microsoft-HTTPAPI/2.0

  Press Enter to exit....

  Microsoft-HTTPAPI/2.0 is the Internet Information Services (IIS) , but there's something funny...

  She has been disabled before!

  Also I have disabled the Windows Service activation process to http://forum.wampserver.com/read.php?2 view, No.8 134915

  I even tried to change the port 1080 and the bar state become green but after trying to install the apache service he gave me the

  In fact, your port 80 is used by:

  Server: Microsoft-HTTPAPI/2.0

  So, what's the problem?

  I found the problem!

  Microsoft-HTTP/API/2.0's not just IIS,

  Microsoft SQL Server Reporting Service !

  Disabled it and apache installed successfully.

  Please help anyone!

• [Need help] New Alienware X 51 BSOD when using the Ports of USB 3.0

  Hello world

  Today, I received my Alienware X 51.  After you set up the system, I plugged my external hard drive USB 3.0 one of the 3 USB ports on the back of the unit.  The system immediately blue armored and closed.  I let the system restart normally, only to find he Blue filtered and restarted again.  After the third BSOD, I deleted all devices on the computer and let it restart.  It has not crashed this time.  Always plug the devices back to demonstrated that when 3 USB hard drive was plugged into the system, the PC crashed.  I am able to reproduce this constantly: hard drive goes in, system hangs.

  I stayed on the phone with Dell technical support tonight, but all they could tell me to do is find another USB 3 device for test ports with.  Since I have none is available, I'm looking at the community of users for more help.  For the record, I managed to extract the files from BSOD dump.  Here is the latest in graphical format:

  

  Anyone seen this before?  My troubleshooting course consisted by uninstalling the driver for the Renesas Electronics USB 3 hub controller supplied with the system and reinstall the drivers using a package available on the Dell (http://downloads.dell.com/Pages/Drivers/alienware-x51.html) website.  It did not work.  I also tried to format the hard drive, but the BSOD persisted.  Needless to say, I am ideas.

  The drive works fine in a USB 2 port.  Of course, I am disappointed that I am not able to use the higher speeds of USB 3 port at this time.

  Anyone seen this before?  Any suggestions on next steps?  What information can provide this help?

  Thank you!

  I am surprised that this post was did not yet a member of Dell since there is a patch to do this, apparently, I had this problem when I arrived to an external hard drive a few days ago

  Remove the current driver for Renesas installed on your Alienware then click on the link below

  http://am.Renesas.com/products/tools/introductory_evaluation_tools/starterkits_evaluation_boards/usb_3_demo_card/index.jsp

  or just click here

  • RENESAS USB3 Host pilot 30230 setup.exe

  installation, this will fix the blue screen issue

• Thunderbolt to Gigabit Ethernet adapter not working

  Hello

  I'm new to this community has never had a problem on my mac since I had last year.  MacBook Pro retina mi 2014 running El captain.

  My ethernet is not picking up DHCP and thunderbolt ethernet does not appear in the network interface.

  I use also fell in love with VGA Converter works on the two test port.

  I also reset the PRAM and the MSC still nothing.  Also restored some peripheral preference to another forum I found on the internet.

  I created another account from administrator to test to see if the interface resumes, still nothing.  How ever wifi works without problem

  Thanks in advance if anyone could help with my problem.

  Dump of information systems presents its collection as below.

  Bolt of lightning to Gigabit Ethernet Adapter:

  Name of seller: Apple Inc..

  Device name: Thunderbolt to Gigabit Ethernet Adapter

  Vendor ID: 0 x 1

  Device ID: 0 x 8003

  Revision of the device: 0x1

  UID: 0X0001000203A8FCF0

  Apple serial number: DTN450706APDWKHBZ

  Route of chain: 1

  Firmware Version: 5.5

  Port (upstream):

  Status: Connected device

  Link status: 0x2

  Speed: up to 10 Gb/s x 1

  Port Micro Firmware Version: 0.0.8

  I have this problem as well. My crush to the ethernet adapter was working yesterday, but now I have not been able to run all day. I even tried everything said in this thread: ImtiazThunderbolt Ethernet does not work after upgrade to Yosemite , you should try what is in the thread, as it has worked for some people.

• Satellite A300 - 1MX Win7: can't capture video from conencted Camcorder FireWire

  Hello

  I have a problem with the video capture from a Sony TRV60E with a Satellite A300 1MX and Windows 7 camcorder via the firewire connector.

  The camera is not recognized (or more) Windows.

  I already changed the firewire driver under windows to the "legacy", also often described in other forums.
  And for a few hours, everything worked fine. The camera has been recognized and Pinnacle Studio 14 could capture video of him.

  But after eight hours, the camera was suddenly is no longer recognized.

  -l' camera is immediately recognized by a XP system
  -On the system W7, I uninstalled, reinstalled the driver firewire, powered down the material (shot of power and the batteries for several minutes), but nothing helped.

  I may have a different firewire driver? Or another operating system?

  Thank you.
  kJ

  It is not easy to say what the problem is here.
  For confuses me the fact that cam has BEEN recognized in the past and now for some reason any it is not recognized correctly.

  All devices are properly recognized in device (firewire port) Manager?
  You can test the firewire port using another device?

  You have discovered what may be the problem. Test port firewire with other devices to see if other devices will be recognized correctly.

• Receiving UDP does not receive messages

  Hello. I have problem with UDP receiver.

  I can receive messages from the same port you write.

  Stream: open vi--> vi--> read vi UDP UDP writing.  Transmitter and receiver usinf th test port.

  When I try to use vi UDP listen port to just read, I get all the data.

  Program flow. I use vi to send the command on the serial port to MCU. Answer MCU return by sending data to the network port using UDP.

  I start vi to listen to a port UDP (see attached), then I sent the order to MCU. I can see the response on Wireshark, but UDP vi does not receive anything.

  I checked the IP address. Lokks all the same. IP address of the PC and decice is the same as when I write and read at the same time. Any other port.

  Any help please.

  Is the port that you want to use to open? For safety that many IT services will be blocked in ports that don't think they are necessary, or don't want to use.

• Winsock gethostbyname() behaves different when debugging

  Hello

  I test porting a library in NI CVI 9.0 and I have just compiled a very simple DLL to perform a function of WinSock on XP SP3. When I run the executable from the command line, gethostbyname() returns the correct data. When I am debugging using the IDE of CVI 9.0, gethostbyname() returns-1.

  I don't know where to start because I don't know why there should be a difference.

  It is compiled into a DLL:

  #include

  #define LIBAPI __declspec (dllexport)

  LIBAPI int WINAPI SYScurrentHost(char *buff, size_t buflen) {}

  result = gethostname (chamois, buflen);

  If result (result);

  Return strlen (buff);

  }

  The main() which calls SYScurrentHost using (such as a console application) from the console returns the actual host name. But when I put a breakpoint in SYScurrentHost(), the result is-1 indicating an error. The LIB file for wsock32.lib is located in "C:\Program NIUninstaller Instruments\CVI90\sdk\lib\msvc\wsock32.lib" I've had to manually add (somehow I have a feeling that it shouldn't be necessary, but I got errors from the linker without him).

  Thank you

  Jason.

  Before making any calls to Winsock, you must initialize the library by calling WSAStartup. You will notice that if you call WSAGetLastError once gethostname returns-1, it returns WSANOTINITIALISED. It appears that the creation of a command window should automatically initialize Winsock, although I have found no documentation to support this thesis.

  A. Mert
  National Instruments

• How to generate a field real-time tiara?

  Hello

  I tried a lot of things, but it is not working properly.

  I logfiles with the data of one ore more test ports. All entries in log file has a time stamp.  Timestamps are not equidistant. I can read the log file and get a table 1 d (n long elements) of the timestamps and a table 2D data (n x m elements m test ports).

  How to generate a report in the tiara with the time that x-axis it? The difficult is, I can't transfer the timescale to tiara.

  I could first convert timestamps double and double transfer al. This does not solve my problem. The tiara-channel resulting if of type 'float' and not 'time '. I need a script to swich the channel to 'time'. I see no solution to load a layout of report (TDR), to call a script to transfer data from additional text.

  Hello bohm,.

  When you write a channel timestamp in a PDM file, tiara automatically identifies it as a weather channel. So when you export the right data, you will get good results ;-).

  To illustrate this, I wrote an example VI: it creates two TDMS files with random timestamps and displays then the two files into a single report of DIAdem. I hope that you find it useful.

  Best regards
  SFK

• VISTRA crashed, monitor and usb keyboard does not work

  WinVista desktop crashed and restart at all.  All I see on the LCD is NO SIGNAL.  The keyboard no longer works.  I tested both the monitor and the keyboard usb on another computer and they work fine.  Test ports usb with a speaker.  Speaker works fine.  I did an oil change of power.  No go.  Vista recovery disc, it can not read. I can't stop starting either because the keyboard does not work.  I can't get to the BIOS. Any suggestions?

  Hi AJKMart,

  I recommend you contact your computer or your motherboard manufacturer, as seems to be a hardware problem.

• HP ztouchsmart h052 usb rear

  I have a new hp touch smart Pavilion 23 h052 leave all in one office and the back usb ports I have work although maybe I uninstalled the drivers or deleted something istake so I deid a system recovery and they still do not work they work right up until yesterday just curious

  Use Diagnostics--> component--> port USB tests to test ports.

  

  If the Diagnostics reports that ports have failed you will need to contact by hitting the repairs.

  Is your computer desktop all-in-one still under warranty?

• Push notification to groups of BES to MDS

  Hello

  Ich have a small question. My Application sends notifications of type push to one or several groups of BES.

  This works well as long as the name of the Group has no spaces in the name as 'Test Group'.

  I have test it with the following to the URL:

  http://10.40.0.25:8080 / push? DESTINATION = $TEST & PORT = 100 & REQUESTURI = /.
  Return value: 505 / HTTP Version not supported

  http://10.40.0.25:8080/push?destination=$test%20Group&port=100&REQUESTURI=/
  Return value: 403 / forbidden

  Can someone help me?

  Thanks in advance

  Benjamin

  Hi Benjamin,

  You're targeting 20,000 users in a unique environment? Are all the user managed from a simple LOW?

  A Central push server can be set up to reach all users of an MDS instance, but 20 000 growth would cause stress. I suggest that additional tests and see how performance is affected before trying with the full 20,000.

• Push the connection interrupted by device - using eclipse of the bb Simulator

  Using BlackBerry plugin for Eclipse

  For OS 6

  After taking two weeks to try and correct an error "not close until you have finished" simple with SQLite, I now have a bit of a configuration issue with the Eclipse software.

  When I push a message to the Simulator, I get the following error.

  <2012-04-18 15:39:15.471 EDT>:[378]:::http://172.17.111.35:[email protected]&priority=2&besurl=192.168.1... pushId = -62be8811:136c6f71d73:-7ff576188, destination = [email protected], result code = 400 net.rim.protocol.iplayer.push.b: Push connection aborted by device>
  

  According to the knowledge base, a 400 error is 'invalid Push to the format.

  Mobile data service 3.7 and earlier versions: the email address or the personal identification number (PIN) used in the Push was not recognized as a user of BlackBerry Enterprise Server enabled for Mobile Data Service. »

  I'm sure it's something with the configuration in the rim.property file.  Something probably must be on or off, I can't understand.

  [MonitorAgent]
  MonitorAgent.listen.port=8070
  
  [WebServer]
  WebServer.Tomcat.transcoding= false
  WebServer.listen.host=localhost
  WebServer.listen.port=8080
  WebServer.listen.sslport=8443
  WebServer.servlet.monitor.port=8070
  WebServer.servlet.monitor.host=localhost
  WebServer.servlet.push.port=81
  WebServer.servlet.push.host=localhost
  WebServer.servlet.push.ssl=false
  
  [SRP]
  SRP.UID= please get one
  SRP.AuthenticationString= Please get one
  SRP.InetAddress= Please get one
  SRP.Port=3101
  SRP.logging=true
  
  [IPPP]
  IPPP.push.listen.tcp.port=81
  IPPP.connection.MaxNumberOfKBytesToSend=128
  IPPP.queue.flowcontrol.window.size=-1
  IPPP.queue.flowcontrol.timeout=600000
  IPPP.logging=true
  
  [UDP]
  UDP.receive.port=19781
  UDP.send.default=19780
  UDP.init=initialization_packet
  UDP.logging=true
  
  [HTTP HANDLER]
  application.handler.http.logging = true
  application.handler.http.CookieSupport = true
  application.handler.http.AuthenticationSupport = true
  application.handler.http.AuthenticationTimeout = 3600000
  application.handler.http.device.connection.timeout = 140000
  application.handler.http.server.connection.timeout = 150000
  application.handler.http.device.credentialTimeout = 60000
  application.handler.http.authentication.mechName2oid = Negotiate=1.2.840.113554.1.2.2, NTLM=1.3.6.1.4.1.311.2.2.10, Basic=1.3.6.1.4.1.88888.1.2
  
  [Security]
  net.rim.security.auth.DefaultDomain = rim.net
  
  [HTTPS HANDLER]
  application.handler.https.allowUntrustedServer = false
  application.handler.https.logging = true
  
  [TLS HANDLER]
  application.handler.tls.allowUntrustedServer = false
  application.handler.tls.logging = true
  
  [OCSP HANDLER]
  application.handler.ocsp.StatusProviders = net.rim.protocol.iplayer.connection.handler.device.ocsp.OCSPProvider
  application.handler.StatusProviders.OCSP.PrimaryResponderRank   = Default
  application.handler.StatusProviders.OCSP.Responder.Default      = http://dhobbs-wnt.rim.net/ocsp
  application.handler.StatusProviders.OCSP.UseDeviceResponders    = yes
  application.handler.StatusProviders.OCSP.UseCertResponders      = yes
  application.handler.ocsp.DebugLogging = no
  
  [LDAP HANDLER]
  application.handler.ldap.DEFAULT_SERVER = dhobbs-wnt
  application.handler.ldap.DEFAULT_PORT   = 389
  application.handler.ldap.DEFAULT_QUERY  = ou=people, o=rim.net
  application.handler.ldap.DEFAULT_LIMIT  = 20
  application.handler.ldap.COMPRESSION    = true
  application.handler.ldap.logging        = false
  
  [Database]
  Database.shouldConnect=false
  BESName=DAISY1
  Database.Driver=sun.jdbc.odbc.JdbcOdbcDriver
  Database.URL=jdbc:odbc:BESMgmt
  Database.DBCycleTimer=5
  
  [ACL]
  ACL.Authorization.Datastore=net.rim.shared.service.authorization.JDBCAuthorizationDatastore
  ACL.Enabled=false
  
  [ESS]
  ESS.helpfile    = help/Using_the_Email_Server_Simulator.html
  ESS.launcher    = bin/launcher.exe
  
  [Email]
  Email.deviceId      =2100000A
  Email.pop3Server    =pop3.server
  Email.smtpServer    =smtp.server
  Email.personal      =Dean Logan
  Email.address       [email protected]
  Email.smtpPort      =25
  Email.pop3Port      =110
  

  Any suggestions?

  Figured it out.

  When you set the port of the unit, I had the wrong port

  _notify = (StreamConnectionNotifier) Connector.open (appAttributes.devicePort + appAttributes.deviceSide);

  My company uses a Test port and a port of Prod, so that we can have 2 versions of the application on the device at the same time.  Then, chaning the listening port of 1315 to 1313 authorized service push push to the appropriate port and the app was able to read the data.