That does Create DAQmx Virtual Channel (TEDS AI accelerometer) actually?

Similar Questions

• Create a virtual channel that increases a counter for each iteration of a cyclic load test

  We will be a long period of cyclic fatigue tests, and I wish I could keep track of which iteration we are on this block.  The current plan is to test for 10 hours at 15 Hz, and then stop test for 2 hours for an inspection of the structure.  Later tests will begin upward.  Each of these blocks of 10 hours can start at a number of 0, but I would like to follow the release of our cell so that when he sees a rising edge (with filtering to take account of any noise) it will increase a 1 meter.  Each sample will then save this number in a column in the data file.  It doesn't have to be perfect in the measurement on the forehead, he sees the new cycle, but there need to be specific in the way that it is not miss or as an additional cycle.

  Is something like this in Signal Express full?

  Yes, what you are proposing is possible with SignalExpress full. You can call LabVIEW signal express code, so call a LabVIEW VI, which contains your counter code is a way to do it. If want to do entirely in SignalExpress you can use DAQmx features by browsing up to add a step > acquire signals > DAQmx acquire and put in place a task entry counter to match your needs.

• DAQmx create virtual channel (VI) error-229771 reports

  Hello

  When in a project that I am working to get error-229771 code whenever I try to run 'DAQmx create Virtual Channel (VI)' this does not happen when I create a vi not in a project.  The problem is that this project is very large and it if poster impossible to recreate. It's several hundred vi. Y at - it something that I missed in the forums and support that could explain this. I created the VI below in the project and outside the project. In the project, the error occurs outside the project, it runs without any problems.

  Message:

  229771 error occurred at .vi:1780003 DAQmx create channel (I-voltage-Basic)

  Possible reasons:

  Internal software error has occurred in the MIG software. Please contact the support of National Instruments.

  Task name: _unnamedTask

  Any help would be appreciated.  Thank you, Matt.

  LabVIEW version: 15.052(32bit)

  OR Max Version: 15.0.f0

  NEITHER DAQmx Verson: 15

  OS: windows 7 service pack 1

  PC: Intel Core i7-2600, 8 GB of ram

  Data Aquistion: NEITHER DAQ USB-6289 calibrated June 2015

  This code snippet returns the name of the first channel of analog input on the device first, and then tries to create a task for her. The bed of the canal, then close the task.

  

  Error message

  

  Hi Matthew,

  Thank you for following up after you fix your problem.  I'm glad to hear that you do not encounter this problem more.

  Here is an article that lists the reasons for this error (although unfortunately, I cannot pin down which is the exact cause in this case).

  http://digital.NI.com/public.nsf/allkb/03123D0E8A36C48E862577A4005B6BAA

  NOTE: This article specifies that the error occurs at startup task VI DAQmx.  You do not use the start task VI, so the task starts automatically in the DAQmx Read function.  The error will occur instead in the DAQmx virtual channel create, that you encounter in your error.

  I hope this gives you an idea about what could have gone wrong, and I'm sorry he is no more details.

  Good programming!

• Error-200431 occurred at .vi DAQmx Create Channel (I-acceleration-accelerometer)

  Hello

  I tried to use DAQmx Create Channel to accelerometer and yet it responds with error (see below). When I use max OR to measure the accelerometer (I-acceleration-accelerometer), there is no error, and I see that acceloremeter works.

  OR PXI-1042 and I use OR-4462 card to measure vibration vith acceloremeter.
  

  Error-200431 occurred at DAQmx Virtual Channel Create

  Possible reasons:

  Physical channel selected does not support the type of measure required by the virtual channel you create.

  Create a channel to a type of measure that is supported by the physical channel, or select a physical channel that supports the type of measure.

  Property: I. MeasType
  Requested value:
  You can select: sound pressure, voltage: Microphone, accelerometer, Position: Eddy Current proximity probe, Force sensor: IEPE, speed sensor: IEPE

  Task name: _unnamedTask<104>

  Hi serdaryilmaz,

  I'm not sure why the accelerometer mode does not work, but it works very well in normal mode - it maybe has to do with the accelerometer, you?  Whatever it is, if it works with the voltage mode, I am happy that we found a way to make it work.  Is this an acceptable work around you?

• problem by creating a virtual traditional NI-DAQ channel

  Hello friends,

  in fact I change computer daq to a machine, but for now I have problems when I try to create a virtual channel.

  I see the jury on the devices and interfaces but when I fill in the parameters of the analog track exactly in step giving the ports, and the channel of material not appear anything and when I finished the configuration in the virtual channel properties appears invalid configuration and there I can't select anything in the hardware channels.

  I don't know what is happening?

  I installed labview 2009 Windows 7 with MAX 5.0 and NI DAQ 9.4

  Please help me or ideas on the...

  Thank you...

  You change os or change at DAQmx. Traditional DAQ has been made obsolete when DAQmx was introduced with LabVIEW 7. If your card is one of the old cards that didn't is not supported by DAQmx, then Yes, you would also have to replace one if you stayed with windows 7.

• problem setting daq virtual channel to PCI-6229

  Hello

  I have trouble to set up a virtual channel to PCI-6229.  It comes to LABVIEW 7.1.  I am updating a VI in LABVIEW 6.1 to 7.1.  When I go through the Assistant of MAX, I get it configured how exactly it is about the version of LABVIEW 6.1, but then under device, there are not listed, although MAX recognizes the labview map in the NOR-DAQmx devices section.

  Please help me on this one, as I'm new to labview and cannot find another way for this VI to work but with virtual Renault.

  Thank you

  Hello

  The PCI-6229 is a map of series M and it is supported only by DAQmx Device Driver

  Since you MENTIONED that it is the virtual channels in LabVIEW 6.1, your old VI must use of the API OR-DAQ traditional (old)

  Howerver the transition from the traditional DAQ in the DAQmx will certainly not be a major concern for you

  Since you're new to LabVIEW, you can quickly adapt to the use of DAQmx

  The following links should help you to learn and get into programming with DAQmx

  http://zone.NI.com/DevZone/CDA/tut/p/ID/3021

  http://digital.NI.com/public.nsf/allkb/BB06D0620FDD7ADB86256D2700557BFC

  http://zone.NI.com/DevZone/CDA/tut/p/ID/5375

  http://zone.NI.com/DevZone/CDA/tut/p/ID/2744

  http://zone.NI.com/DevZone/CDA/tut/p/ID/4342

  No matter what other assistanceyou seek, let us know

  Kind regards

  Dev

• Physical channel selected does not support the type of output required by virtual channel

  I use a box USB-6251.  Inside of MAX, I can set the device to Dev1 / ao1 sine wave generation and if he have output a sine wave.  When I use DAQmx DAQmxCreateAOFuncGenChan function I get error: selected physical channel does not support the type of output required by virtual channel.  The pilot DAQmx does FuncGen on the box USB-6251 or MAX out a set of tensions?

  Hi Paul,.

  Welcome to the Forums EITHER!  The DAQmxCreateAOFuncGenChan is supported only on products Elvis II.  For other devices, including the 6251, you must use the ordinary DAQmxCreateAOVoltageChan and create your own data buffer.  I would recommend looking in the following example:

  Start > all programs > National Instruments > NOR-DAQ > textual Code > ANSI C examples...

  Analog on > generate voltage > Cont Gen Volt Wfm - Int Clk

  In MAX the Sinewave output is used as a test signal - in this case MAX is a period of the wave sine values to write to the buffer and generate these data.  Again, you can produce a sine wave (or any other function) using the AOVoltageChan, but the AOFunctionGenChan is used only with Elvis II.  Just generate data points for the sine wave that will produce DAQ hardware.

  -John

• Duplicate a CTR Global Virtual Channel Max does not update the CO. Pulse.Term setting

  Hello

  Here is the description of the problem:

  MAX version: 4.6.2f1

  DAQmx: 9.0.2

  Material: cDAQ-9178, output digital OR-9474.

  This module to:

  • CRT out 0 <-->PFI3
  • CTR 1 to <-->PFI7
  • TRM 2 on <-->PFI1
  • CTR 3 on <-->PFI5

  1. in MAX create a Global as an exit CTR on ctr0 virtual channel.

  2 use the double in the menu to create a second output of counter. Change its name and replace it with ctr ctr output OUT 1.

  3 al ' MAX, the pulse output configuration pane must take into account the change showing the terminal output pointing to the appropriate forum

  4 export settings in an INI file and look at the CO. Pulse.Term settings for both channels CTR: they will appear together with the SAME exhortations!

  5. with the help of LabVIEW write a vi that generate pulses on these 2 ways, you will get the error-89137 saying that a PFIi resource is already in use. If you look at the Task CO. property Pulse.Terminal, it returns the same to two piles, which is the same error in the ini file.

  Can someone at arrival OR this? THX.

  Laurent

  PS: I posted this message in the LabVIEW Board as I have not found one for MAX

  Hello

  Corrective action request (CAR) ID: 228780

  Best regards

  M Ali

  Engineering applications

  National Instruments

• Writing to the nodes property DAQmx channel does not refresh the channel values

  Hi all

  I have a riddle.  I created a task programmatically in LabVIEW and programmatically added several analog input channels to the task.  It's easy.

  I wish that my user must be able to modify the individual channels within the task.  To this end, I created a set of screws that allow it to change the settings appropriate to the channel (for example, if it is a channel of thermocouple, it can change the type of thermocouple, CRC value, etc... If it is a strain gauge channel, it can change the coefficient of fish and so on).  These screws all works beautifully, like the VI where they live.

  The specific question that I have is that writing to the channel property nodes refreshes not communication channels.  See the images below.  The first image is the code that needs to define new channels of communication:

  

  Note that immediately after setting the property nodes, I read their values back, just to see what comes out back.

  The second image is an image of the public Service immediately after the execution of this VI.  Note that the values read from the channel property nodes did not updated to match to the set of values, but instead kept their initial configuration values:

  

  What I am doing wrong?  I fought this for a few days now and I'm stumped.

  Thanks for your time!

  Diane

  Hi, Diane.  A week ago, I also had a problem changing the channel properties (not sure that our situtions are exactly comparable, but...).  My 'solution' to want to change the appearance of the task was to just throw the original task and recreate all the elements of the task from scratch.

  I've not done enough 'experiments' to work when you can and cannot change, but am now much more cautious...

  Bob Schor

• Time scale does not properly after separation of the two signals of virtual channel

  Hi all

  I have a problem when I use a virtual channel with two analog inputs. I'm cutting the two signals into two separate tables of waveform, as shown in the attachment. The two signals seem to be reading very well, the problem is that the time scale (x-axis) begins to act on the strange. Seconds displayed time seems to keep jumping up and down at a high frequency, resulting in the two signals of displayed does not correctly in the table of waveform. Could someone please try to help me? Any help would be greatly appreciated!

  Thanks in advance.

  Try to acquire a signal with first time information. You can replace the DBL 2D with a data type of 1 d wave. You don't need this code extra silly - just a function of Board Index to get the separate channels.

• Can NOR-DAQmx application read a virtual channel with two independent

  Two standalone applications OR-DAQmx need to read the same virtual channels of the same material at a different frequency at the same time. Is this possible?

  Thank you

  This is not possible since which application is executed, the source is reserved so that the second application cannot read.

• Programmatically, create a multi-channel DaqMX task

  Is there a way to create a task of multichannel DaqMX programmatically, without having a task to copy?

  Yes and it is an easy way to find a way to do it.

  Start by creating a task in MAX (Ben, but I want to avod MAX!) Don't be afraid that it's just a one time event that will allow us to know what are the steps)

  Go to a block diagram and steady decline DAQmx task on the diagram and choose the task you created in MAX.

  Right click and select 'create configuration and example '. LV will create the code that goes with the taks.

  Study the config VI that was created. It will show you what it takes to create a task without MAX.

  I hope that helps!

  Ben

• I accidentally loaded a .iso file on my PC and can not get rid of it. When I try to delete the file it says that the file is opened by the system. Also the file created 3 virtual drives like E:, F: and G: __Please let me know how I can remove this .iso

  I accidentally loaded a .iso file on my PC and can not get rid of it.  When I try to delete the file it says that the file is opened by the system.  Also the file created 3 virtual drives like E:, F: and G:
  Please let me know how I can remove this .iso file.

  Try Safe Mode. Repeatedly press the F8 key as the computer starts getting the menu diagnosis. Use the arrow key to select Mode without failure. MS - MVP - Elephant Boy computers - don't panic!

• Is there a download from Microsoft which will create a bootable usb media that does not have the drivers?

  Original title: A bootable Windows 7 media

  I work on a Lenovo 2-in-1 with Windows 7 (for games) and 10 (for a normal use) Windows to dual-boot. I created a USB stick with Windows 7 Pro (64 bit) of a legitimate Windows 7 Pro disc. The computer starts on the usb device and plays normally, however, one of the steps asks a driver for cd/dvd and this 2-in-1 (Lenovo Flex 3) doesn't have a built-in CD/DVD. All other drivers are located in a folder system. My question is, given my key Windows 7 can I create a new bootable media that does not demand drivers? Is there a download from Microsoft which will create a bootable usb media that does not have the drivers? I know that I can reinstall the drivers manually after the installation.

  Thank you

  Matt Armshaw

  Windows 7 or Windows 10 come preinstalled?

  If you install Windows 7 on a system that is preinstalled with Windows 10, you must do the following before:

  -Disable the secure boot UEFI

  -Disable the quick start

  -L' install created media can be corrupted.

  How to: Dual Boot Windows 7 or Windows 8 with Windows installed 10 first

  I suggest that you try to create another bootable copy.

• When I try to read Blu - Ray, it says "Windows Media Player cannot play the DVD. The disk has been created in a way that does not support the player. »

  Original title: Blu - Ray

  My computer can read blu - ray, but when I try to play one, it says "Windows Media Player cannot play the DVD. The disk has been created in a way that does not support the player. "How should I do?

  Hello
   
  The Blu - ray disc format is not supported in Windows Media Player. To play a Blu - ray Disc, you must use a non-Microsoft program that supports playback of Blu ray and a device that can play Blu ray discs.
   
  See the article mentioned below:
   
   
  Read a CD or a DVD in Windows Media Player: http://windows.microsoft.com/en-us/windows7/Play-a-CD-or-DVD-in-Windows-Media-Player
   
  Note: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.