The FRU for the LSI 9260-8i cable?

Similar Questions

• Sensor storage LSI 9260-8i in ESX 5.5

  Hi all

  I recently bought a new RAID controller for my 5.5u2 ESXi host. I chose the LSI 9260-8i to cause the positive reviews, price and compatibility 5.5. The main objective of the new RAID controller was to add the visibility of table in ESXi "State of material" and to allow management from a virtual machine via the MegaRAID Storage Manager. I flashed the 9260 with the latest firmware and then installed 5.5u2. The LSI RAID controller was found and both my drives are available and work as expected.

  Unfortunately, I have none is a sensor of storage in the status tab of the hardware. I tried to installed the Legacy and native drivers as the latest SIGS, all found HERE. I had success the legacy driver update but PMI would not update.

  Please respond if you have an LSI 9260 with 5.5 ESXi. I'm curious in the storage sensor is visible to you.

  Thank you!

  What do you mean by "PMI would not be updated"? I've updated smis-provider with:

  # software esxcli vib install d ' / path/VMW-ESX-5.x.0-lsiprovider-500.04.V0.54-0004-offline_bundle-2395881.zip '.

  .. .and everything went well. After the reboot, I can see State of health in the Hardware tab.

  BTW, you have 5.5 ESXi, you probably use VMW-ESX-5.5.0-lsiprovider-500.04.V0.54-0004-2371726.zip, listed as a provider of PMI for 5.5.

  But have you tried the other one, VMW-ESX-5.x.0-lsiprovider-500.04.V0.54-0004-2395881.zip, for 5.x?

  And one more thing: your controller reports its health status at least using the tool (storcli, megacli)?

• Photosmart 7520: Hi, have 7520. for the configuration of the fax, dsl with cable/tv/phone connection.

  Hi, if based on the system hookup, dsl(cable/telephone/tv). you need to connect a line to the answering machine. It's good, but if the phone base ref years machine isn't near the fax machine, how do you connect? I plugged a fax machine to the outlet line.

  Hello

  Your modem has port for fax? You must connect your printer to that port OR another phone line OR try the following:

  http://SmallBusiness.Chron.com/phone-fax-modem-share-same-line-57618.html

  and the photosmart 7520 does not have a printer capable of efax. The 7520 has however an extremist fax integrated into it, that's free too long you have a phone line.

  Source:

  http://h30434.www3.HP.com/T5/HP-connected-mobile-printing-and-cloud-printing/I-have-an-HP-Photosmart-7520-do-I-have-to-pay-eFax-to-fax/TD-p/2193039

  Kind regards.

• computer not automatically standby (formerly titled "impossible computer automatically sleep when it is connected to the internet with modem cable")

  Hi, I noticed recently that my computer (Windows XP Media Center Edition 2005) is unable to sleep automatically when it is connected to the internet with a cable modem. Change the settings for my current power mode and try a different feeding regime (diagrams of Windows XP default power and power management, I created) only solves the problem for 2 days at most. I also tried to change the settings for the other power plans mentioned, and yet once again, the problem was only set for two days at the most. I also tried turning off my computer, restarting my computer, recording Powercfg /Restore Default policies in Run, saving sfc/scannow in Run, and again, I got the same result. Reset and power cycling the modem cable is not helped either. To help you better understand the problem, for example, if I had the date set for the screensaver set to 1 minute, the time for the monitor to turn off set to 2 minutes and time for your computer set to 3 minutes, the screen saver activate after 1 minute, the monitor turns off after 2 minutes, but the computer would not sleep mode after 3 minutes , even after an hour or more. I tried to check the Task Manager, and I have not noticed any process that would be interrupting the day before. However, I noticed that when I turned on the monitor by moving the mouse, even when the computer was unable to sleep and unplugged the ethernet cable from the cable modem and waited, the computer has entered standby as it should have.  I tried to find a solution for more than a week, contributions for this issue would be greatly appreciated. Thank you for taking the time to read my post. (Update: it seems that the problem is something else then my cable modem.)

  Hello

  Thank you for the update.

  This behavior can occur because of possible conflicts of third-party software, which includes the third-party security software.

  You can also temporarily disable third-party security software and firewalls installed on the system and check the issue.

  If disabling the antivirus software solves the problem, you may need to configure the settings of the antivirus as a result program. Please contact the software vendor for assistance in this regard.

  Note: be sure to enable the security software on the computer after checking the issue.

  Note: When you perform a clean boot, you can activate services for the modem, network card and disable third-party services to check the issue.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• I have my printer connected to my router via a usb cable... I also have my (Vista) computer connected to the router by ethernet cable. How can I set the computer to print on my prints through the router?

  I have my printer connected to my router via a usb cable. I also have my (Vista) computer connected to the router by ethernet cable. How can I set the computer to print to my printer via the router?

  Usually, you need to install the printing software / drivers on your PC, configured / installed specially for a printer "remote" (its an option in the installation of the printer software)

• The connection between your cable modem, router or access point, and Internet are broken.

  What is the average message "the connection between your cable modum, router or access point, and internet are broken" and how to fix it?  We use internet provider time warner.  Can I access online using mini jetpack, but not through time warner.  Is the problem with our internet service or hardware problem?

  Hello Terri,

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the issue.

  This problem may occur because of damaged or incorrect network settings.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the network troubleshooting and check.
  Reference:
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  Note: You can run utilities times 'Internet connection' and 'network card'.

  If this does not help, use method 2.

  Method 2:
  Reset TCP/IP and check the issue.
  Refer to this article:
  How to reset TCP/IP using the NetShell utility
  https://support.Microsoft.com/en-us/KB/299357

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Laptop connected to the TV using a cable HDMI gets no picture just audio

  My TV captures the laptops of screen cable hdmi soon an i plug it in but won't play no audio and I cannot work out how to get the audio working. Help, please

  Hi cus.

  VGA, DVI and component video cables do support audio signals. HDMI cables are supported, but not all, audio signals compatible HDMI video audio support cards. If your TV has an audio input, you might be able to connect an audio cable separated from the sound card of your computer directly to the TV. Otherwise, you need to connect the different audio signal to an output device, such as external speakers or your stereo.

  HDTV: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/HDTV-frequently-asked-questions

  Update the driver for graphics card on the computer and check.

  How to upgrade the graphics card on the machine driver

  1. click on Start, click Control Panel, and then double-click System.

  2. click on the hardware tab, then Device Manager.

  NOTE: If you are prompted for an administrator password or for confirmation, type the password, or click on continue.

  3. click on display adapters to expand.

  4. under display adapters, double-click the entry for your graphics cards, and then click the driver tab.

  5. click on Update driver software.

  6. follow the Wizard update driver to update the driver graphics cards .

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Is there a way to tell if a virtual machine was created using the LSI or BusLogic SCSI device?

  Is there a way to tell if a virtual machine was created using the LSI or BusLogic SCSI device?

  No worries, you can try going to the virtual machine and looking for an online .vmx file such as - scsi0.virtualDev = "free".

  I shot on a vmware workstation VM, don't know if it's exactly the same vmware server, but is worth a visit.

  • Kyle

• When I connect the USB and LAN cable does not my trackpad

  Hey guys how are you.

  When I connect the USB and LAN cable does not my trackpad

  How can I fix this error. Please teach me.

  Which macbook model do you have?

  a USB mouse still works?

  your keyboard still works?

  No matter which USB port you use?

  No matter what USB device allows you to create this error?

• 13 spectrum HP 3004TU: Sound comes only not on the TV through HDMI cable

  Same problem like some users: using Win10 and despite the video past to the TV via HDMI cable I can't get the sound in the PC, and not in the TV. Drilling...

  He said that it is not plugged

  @porrinho

  Try to run this.

  http://ftp.HP.com/pub/SoftPaq/sp72001-72500/sp72370.exe

  REO

• I added a router and a connection high speed using windows vistawhen pc is connected to the router her there is no internet connection. When the pc connected to the Internet by modem cable is available

  I added a router and a connection high speed using windows vistawhen pc is connected to the router her there is no internet connection. When the pc connected to the Internet by modem cable is available

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  It will be useful.

• My photosmart c309g-m is connected to the router by ethernet cable. Can I add?

  My photosmart c309g-m is connected to the router by ethernet cable.  Can I still add to e-print?

  Hello

  Is a printer ready ePrint? You can use the home router to access the internet? If Yes and Yes, then you should be able to do.

  Kind regards.

• Unable to connect to the internet without Ethernet cable.

  I have a new router, but can't seem to connect to the internet without Ethernet cable. Trouble Shooter diagnostic tells me that "Windows cannot communicate with the device or resource (primary DNS server). I am at a total loss!

  Not sure, but this post can help (as seems to be the same or a related problem) - http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/cant-communicate-with-primary-dns-server/9043f785-2f4e-4cc1-adf5-6ba5ca413749?page=1&tm=1388597381623

  Good reading and see if it helps.

• Add disk Workflow fails when you use the LSI Logic SAS SCSI controller

  I'm in vCenter Orchestrator 4.0.1

  When you try to run the workflow work add drive on a virtual machine that uses the LSI Logic SAS SCSI controller I get an error no controller found.

  This workflow is under: library-> VIM 3-> Virtual Machine Management-> device management

  The workflow add disk supports the LSI Logic SAS controller?  If this is not the case, no idea of how to create my own custom adds workflow to disk that would work with this controller?

  Thank you!

  Which plugin you have configured to talk to your Virtual Center? the plugin 3.5 or 4.0 plugin? If you have used the plugin 4.0, you must use the library-> VC-> * workflow so that the correct objects get used.

• Cache SSD c2100 & LSI 9260-8i

  Hello

  On a C2100 with a LSI 9260-8i, what are the requirements for cache ssd work? I would add 2 SSDS (internally) to activate this feature, but I don't know if in addition the SSDS, I need nothing else, or if he is still supported on this server with the 9260-8i

  Thank you

  Asempris,

  I apologize, the C2100 does not support the Cachecade, which is the feature you describe using the SSD for the cache. You can also find more information on the C2100 here - http://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_cloud_products/poweredge-c2100_Owner%27s%20Manual_en-us.pdf

  Let me know how it goes.