The goal of the DSC HX10v quality is higher than the HX9v DSC?

Similar Questions

• Slide the optimized quality vs high (24 bit)

  Captivate v5.5

  All my projects are created with quality optimized blade.

  Looking at my projects via our LMS the quality of some slides are poor compared to the original - lines down and through the slides, etc.

  Dept. computer SCIENCE suggested I download the project again on the LMS with quality slide 'High (24-bit)' and see if it improves quality when read through our LMS.

  While preparing for this I found that my project with a quality of "Optimized" Blade is 56.1 MB, but when past zipper 'High' quality the size of the file is actually slightly less, 55.6 mb. I expect the size of the file to be much greater when the high value.

  This makes me think that change it 'High' project will make no difference for the quality when read through our LMS.

  Can someone explain (in simple terms please) what is actually the difference in 'quality' of a project of v5.5 slides are all 'optimised' against one who has all the parts, set "High (24 bit)"

  Do you think that change a project to high 24-bit will improve the Visual quality through our LMS vs a project set to optimized?

  Thank you in advance,

  NEL

  Yes, it's a little known fact that using high quality 24-bit actually causes file sizes SMALLER.  Optimized is supposed to choose the best method of compression on a basis of slides while high 24 bit compression just apply the same setting to all slides and is used as the default output of the PNG image.  For some reason, optimized didn't bat raise 24 bits, even if most of the literature says it should.

  To get rid of your objects on the slide, try turning off advanced project Compression.

• I look at the TB dashboard seen comes from open TB. On the left, I see folders. The folder "sent", lets say, is higher than the "Outbox" folder I want to

  I look at the TB dashboard seen comes from open TB. On the left, I see folders. The folder "sent", lets say, is higher than the "Outbox" folder I want to put the "Outbox" folder above the folder "sent". How do I do this ever?

  I know that the addon will allow you to rearrange accounts, so you could put 'Local folders' over another e-mail account.
  It will also allow you to use files within an account.

  So if you have a Pop email account that uses the Global setting of the "Inbox", then it should allow you to move the position of the Outbox within this special account.

  But as the 'Outbox' is a 'Local folder' folder, I'm not sure that you can move it out of "Local folders" and reposition it on another account.

  The method for moving files is done via the menu bar.
  'Tools' > 'manually sort folders ".
  Select the folder and use "move up" or "Down" buttons.
  Then click on the button "refresh folderpane' to see the new sort order.

• There was an update to Windows XP sp1 would recognize higher than 127 readers ~ 137 GB, why this update was not in the version later service pack?

  (1) there was an update to Windows XP sp1 would recognize higher than 127 readers ~ 137 GB, why this update was not in the version later service pack?

  (2) where can I find so that I can then reinstall windows XP, updated to sp1, install the patch to see the complete player to sp2 and 3 can be installed?

  original title: supervision XP

  Maybe the disc has been formatted as part of your original installation of Windows XP with a pre - SP1 version of Windows.  At that point, he could only format the drive as 137 GB.  After you upgrade to a post-SP1 version of Windows, look at your hard drive with Disk Manager (start-> Run-> "diskmgmt.msc").  It can show the rest of your unused space that you might then be able to allocate in a second partition.

  If you want to keep one big partition, you will need to get a 3rd third party tool that can extend your current 137 GB partition to use more of the available space.  Google for it, plenty of them out there including those that are free.

  HTH,
  JW

• Manager tasks shows my CPU 100% usage but when I go to the process tab only a handful of programs with a percentage higher than 0 if displayed and none of those who are more than 3%

  Original title: Task Manager

  Manager tasks shows my CPU 100% usage but when I go to the processes tab and sort by CPU usage there are only a handful of programs with a percentage higher than 0 if displayed and none of those who are more than 3%.  What else is using my system resources that is not displayed by the Task Manager?

  Click Show processes from all users . There may be other systemic processes and processes that run under other accounts.

  Ramesh Srinivasan, Microsoft MVP [Windows Desktop Experience]

• Higher than the usual number of download errors

  Hello

  I was just curious if anyone here knew nothing of a level higher than the usual number of download errors I hear on clients.

  The anaylytics seems to backup the fact that several of our downloads fail outside the previous months (based on the new issue that comes out).

  Is there some sort of infrastructure maintenance going on right now?

  Thanks for any idea that you might be able to provide!

  Gold support would be the correct place. I don't know who you might meet instead of. I know that some members of staff watching these forums, but this isn't the resource, so that they are intended to be used.

• Audio Fadin incoming and outgoing, but the video quality remains high.

  Hello. I am regularly skyping someone, but the incoming audio signal began fade in and out and sometimes mute altogether. The video quality is very good and she can still hear and see me OK. The volume for Skype and everything else is wound up to the maximum. I tried skyping someone else and the problem was not present.

  I do not understand how the audio quality that I can fade, but the video quality does not change. I would have thought if they had problems of band bandwidth then the video would have refused and the Lady, I'm not talking would receive me in this good quality either.

  Is anyone know something about this problem and a possible solution?

  Thank you

  Hello. In the case where someone comes across it because they have the same or similar problem I found the solution. It turns out, somehow, that the volume of my microphone had been wound up to the maximum. Because Skype reduces the audio signal entering when you make noise, the person I was calling I couldn't hear because I was broadcasting involuntarily every tiny noise. This interrupts my incoming audio. For some reason I have the microphone picks up a ridiculous level of background noise. Only, I discovered this after a test of back to back with my mother's laptop. To stop the problem I just wrapped up my microphone volume down in audio on Skype settings until there no sign up tapping or other noises. So I send you not now sounds that would hurt my incoming audio. It also explains how the Lady I was calling could still hear me fine and the quality of the video never abandoned, but the audio signal coming at my end was.

• InDesign cc export presets pdf for the quality and high quality printing press are missing.

  I have more quality of printing or high-quality print options to export a PDF file. Is - this intentional? Can I get back them?

  The first thing to try is repalcing preferences and restart the computer. See replace your preferences

  If this does not work, I put a folder of the old benefits here: https://www.hightail.com/download/OGhkZ285Q1JBNkUwTWRVag

• When the stream through flash quality is worse than Live Encoder

  I am creating a system where people can broadcast to a Flash Media Server. When I aired in the flow using direct, the video seems decent. When I try to stream Flash, the video comes out strongly pixelated.

  The only code I can find to do it is:

  Cam = Camera.getCamera ();

  cam.setQuality (0, 100);

  NS = new NetStream (nc);
  ns.attachCamera (cam);

  Should not be a way of resolution of entry? Encoder Live has ~ 15 parameters, are these adjustable parameters, with the release of Flash?

  You must set the mode also

  camera0.setmode (240,320,30,false);

• How can I activate my volume higher than does the volume control

  I would like to get more than allows the volume control. Just don't go to loud. I have a toshiba laptop with Windows 7.

  Hello

  I suggest you to add speakers to the audio output of the laptop. If you use small speakers that were included with the computer, you will not get the best performance available. New speakers offer more options to optimize the audio output.

  Also buy a set with a subwoofer if you want quality entertainment at home or in your office.

  For your reference: Getting sound from your computer: recommended links.

  http://Windows.Microsoft.com/en-us/Windows7/getting-sound-from-your-computer-recommended-links

  Hope this information is useful.

• PCI-6120 noise performance is higher than in the data sheet.

  I use the PCI-6120 card in warp mode, at 1 MHz. everything works, but there seems to be a discrepancy between the measured acoustic performance (with 50 ohm or short) and performance between quotes in the datasheet, 6120/6115. Here is my comparison.

  City of range AI N + Q (uV) measured N (uVrms)

  +/-42  V          550                               1410

  +/-20  V          220                               600

  +/-10  V          110                               280

  +/-5    V          69                                 140

  +/-2    V          31                                 60

  +/-1    V          18                                 30

  +/-0.5 V          10                                 20

  +/-0.2 V          5.1                                15

  It seems to me that N + Q data are shifted a range of analog input as numbers are good but not on the beaches of right. For example, the range V cited 42 N + Q agrees with the V 20 measured noise range. Everyone knows this?

  So what you measured here is actually the system noise, who we spec on page 4 of the specification, uncertainty about the noise, which we spec on page 3.  The noise of the system for the PCI-6120 is shown below.  To calculate the noise from the system of these specs, you use the following formula:

  (LSBrms system noise) * (Input Range) /(2^Resolution) = Vrms system noise

  Thus, for the 42V range, noise specified in LSBrms is 1.2 LSBrms.  The input range is 84 (±42V is total 84 volts).  The resolution is 16 bit.  So:

  1.2* ((84) /(2^16)) = 0.001538 V = 1 538 uV

  For each of the beaches, the sound of the system is:

  Range	LSBS	Sound system (µV)
  42	1.2	1538.09
  20	1.2	732.42
  10	1.2	366.21
  5	1.5	228,88
  2	1.7	103.76
  1	2	61.04
  0.5	2.2	33,57
  0.2	2.8	17.09

  Hope that answers your question.

• Using package firmware level higher than the current version of UCSM?

  It's probably been asked before, but I couldn't find an answer.

  Can I download and use a blade firmware that is greater than the UCSM version?  For example, my UCSM is at version 2.2 (3d), but I want to install a package of 2.2(5b) blade firmware.

  Is this supported without first UCSM upgrading and interconnection of fabric?

  Hey, Walt,

  It is not supported so that your blades at a higher level than your infrastructure, so firmware you want to upgrade the UCSM/FI/IOM until you upgrade the blades. Here are some useful documents:

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/SW/firmware-m...

  You can use this cross reference your HW and SW to ensure they are compatible with one another:

  http://www.Cisco.com/Web/TechDoc/UCS/interoperability/matrix/matrix.html

  Let us know if you have any other questions.

  HTH,

  Wes

• EZVPN connection fails with the error "Split tunnel higher than max attributes...."

  Hello

  We have ASA 5520 acting as the VPN server and the router Cisco 1941 as EZVPN client. These last days of customer is not able to establish the vpn connection. 1941 continuous router generates the below the log messages

  ---------------

  001569: Jul 22 ABC 12:19:05.883: CRYPTO-4-EZVPN_SA_LIMIT %: EZVPN (VPNGROUP) Split tunnel attributes (51) greater than max allowed split attributes (50)

  001574: Jul 22 ABC 12:19:07.835: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = vpn_user group = VPNGROUP Client_public_addr = Server_public_addr =

  004943: Jul 22 ABC 11:32:42.247: % IP_VFR-4-FRAG_TABLE_OVERFLOW: Dialer1: the table fragment has reached its maximum 16

  ---------------

  Future prospects for aid and the suggestion of experts

  Thank you

  Israr Ahmad

  Yes, your split tunnel access-list is too big, and he has reached the maximum number of lines.

  Try to reduce the number of ACL for your tunnel of split ACL maybe combining the subnets if possible.

• How can I make my text even the first letter to the last letter after I twisted it? My "S" is higher than my "D".

  

  It's always a direct envelope? You can adjust the envelope using the gradient mesh tool.

• Host memory consumption is higher than the comments its use (incl. Cached) and overhead?

  I'm under ESXi 5.1. I don't have any custom reserve configured for memory. I'm running in CVS 'Sandy Bridge' mode.

  I noticed earlier than expected host memory consumed on many of my guests. This example comments running Server R2 2012 with the latest version of VMware tools running.

  VMware reports

  

  The guest operating system reports

  

  My understanding is that the "Standby" and "Modified" on the client contains the ' cache ', and the 'Cached' memory prompt is the typical response to this question that I see when people seek only to the memory of 'In Use'. In my case, I'm factoring in the memory cache, my guest shows 3805 MB of real memory, yet my host shows 7.68 GB of memory consumed host, with only 68 MB of general consumption. According to my calculations, the virtual machine should be only consume about 4.28 GB of memory.

  Post edited by: bradduane Replace the values of text with screenshots.

  I think I found my answer in the guide 'Understanding memory resources management' here: http://www.vmware.com/files/pdf/mem_mgmt_perf_vsphere5.pdf

  Section "when to retrieve memory host" page 15:

  «In the high State, the use of global memory machine virtual comments is smaller than the size of the host memory.» Whether or not the host memory is overcommitted, the hypervisor will not recover memory via hot-air balloon or permutation. (It is true that when the limit memory VM is not set).

  If memory free host down to the low threshold, the hypervisor begins to find the memory using the balloon. Balloon happens before free memory has actually reached the soft threshold because it takes time for the balloon pilot to allocate and PIN memory physics reviews. Usually, the balloon pilot is able to retrieve the memory in a timely order to keep free memory in the host above the soft line. »

  I checked esxtop, pressing "m" for the display of the memory, and I see that hosts VMKMEM shows 'State', so the only memory of way either currently retrieved is by sharing the page. Only when I start to run out of memory of the host, that this State becomes 'soft' or 'hard', balloon or Exchange will be held in order to free the "free" memory of comments. ESXTOP show my 'minfree"than 940 MB, while it shows that I physically 6960MB of free memory.