the installed switches?

Similar Questions

• Tecra S11 - bluescreen when the WiFi switch is on

  I've known several accidents suddenly blue screen, with apparently no advice. After several tests of different conditions I counted it takes place when the WiFi switch is on. So, it should be associated with Bluetooth or WiFi.

  Any suggestions how to proceed further? apparently I have the latest drivers (Windows 7 64)
  Thanks, Guido

  Hey Buddy,

  Have you already checked the BIOS if you have installed the latest version? If this is not the case check this on the Web from Toshiba site and make an update of the BIOS. Maybe it helps

  But I had a similar problem last year and the solution was exchanging the WLAN card.

  I think your Tecra S11 should still be under warranty and in this case that the repair will be free. :)

• Tecra 9100: How to enable the WLan switch?

  Hi, new here.

  I have trouble getting the Toshiba Wireless LAN Mini PCI Card to work.

  I installed all the latest drivers on the Toshiba site.

  It is activated in windows and the switch on the front of the laptop is on. 6 led is off.
  The FN + F8/Wireless icon button does nothing.

  Windows repeat me any available wireless network.

  When I try and turn on the wireless card switch network device software Toshiba it just says, 'wireless communication is disabled. Please activate the wireless communication switch. »

  The switch on the front would be tired?

  Any help would be greatly appreciated.

  Thank you

  Oceaness

  Hello

  I guess the 6 LED's LED wireless card.

  This LED should shine when you activate the WLan switch on the side of the laptop.
  Looks like you have not activated the WLan switch.
  I put t know exactly where the WLan switch, but you should check the front of the laptop near the headphone jack.

  Check it out.
  Then the LED should shine and you must activate the antenna with the FN + F8 key combination.

• Network with Airport Extreme problems connected to the Linksys switch

  I have a wired network in my house.  It has the following configuration: Modem base station Airport Extreme for Linksys switch and then all wired connections.  It is in a wiring closet in a room upstairs.  I have 2 other extremes from the airport, to spread out of the range, but they are currently disabled and disconnected from the network until I have found why I get auto ip address on several of my wired connections.  I have reset the modem, EI and switch.  More wired connections seem to be working very well, but there are 4 or 5 who say that the ethernet cable is connected, but it can not connect to the internet because of a self assigned ip address.  I thought maybe it was a problem with the port of the switch, but when I plugged a cable work in, everything worked again.  Thus, for example, on my iMac, in a study downstairs, I had plugged on the ethernet port in the wall.  He let me only to connect to wireless internet.  He says the ethernet connection had a self assigned ip.  I went upstairs and took the cable from the switch and directly connected to the Airport Extreme, and then connect to this iMac worked fine via ethernet.  So I'm really confused as to why it does not work when it is connected to the switch.  Why are only a few connections ethernet works and others not?

  Any help would be greatly appreciated.

  Why are only a few connections ethernet works and others not?

  Because either you have a bad port on the switch (unlikely, but possible) or a wired Ethernet connection bad, or maybe both ends of several of the Ethernet cables (99% of the time, the problem is in the wiring or connectors Ethernet... not the switch).

  But, we must test the switch first and then work from there.  It might be much easier to call a guy from wire or the custom installation specialist to do all this for you, but if you want to give it a try... Here's how.  It is not difficult at this stage, just take some time.

  Unplug the switch except the Ethernet cable that connects the AirPort Extreme to each cable Ethernet switch.  Label each Ethernet cable with a number or a letter you can install the wires in their original position on the switch.

  Use of a laptop computer with an Ethernet port and a short, spare Ethernet cable... virtually no matter what length will make... and turn off the WiFi on the laptop so it should use Ethernet to connect to Internet.

  Test an Ethernet port on the switch with the laptop and the Ethernet cable to make sure that you have get a good Internet connection. If you do so, test the next port of the switch. Continue until all ports of the switch has been tested.  With luck, they will all work.

  If this is the case... which is likely... then you know that the Ethernet switch is working properly.

  Now things get a little more complicated. Ideally, you have documentation that tells you what Ethernet cable goes to what area of the House. If you don't, just connect the Ethernet cable to the switch... then go to the other end of the Ethernet cable to the wall outlet and connect the computer laptop and short Ethernet cable to the wall socket.

  If you have no documentation to indicate where each cable goes, so go ahead and connect all the Ethernet cables to the switch.

  Still, make sure that the wireless is disabled on the laptop so that it can only connect to the Internet via an Ethernet connection. Check if you can get a good connection Internet in this way. If you can, then you know that the individual Ethernet cable and the Ethernet port on the wall are working properly...

  Test other areas one at a time the same way.  You are very likely going to find Ethernet cables or a wall of ports that do not work properly. The hardest part here is that you... or a wire guy... will have to check the Ethernet cable at both ends to ensure that the Ethernet Sockets have been installed correctly.  It is not easy. The wires are tiny and its easy to get involved.  Installation of new Ethernet cards, it's really a job for an experienced guy who will provide hopefully a cable Tester well when it comes.

  Some Ethernet will certainly be replaced.  In rare cases, the cable itself has a break somewhere... and it's not easy to fix something like this, without pulling new cable... that would not be possible according to the House provision.

  When you know that all ports on the switch are working and all ports Ethernet wall around the House work... so... we can get the network set in place and working properly.

• It takes up to 4 minutes for the player switch between library and Rip, and vice versa.

  I run Media Player 11 on my XP machine with spare 120G on the C: memory and 3G - recently, it takes up to 4 minutes for the player switch between library and Rip, and vice versa. I have re-installed twice but no change. No new software has been installed before this time.

  Hello Absno69,

  Thank you for your message.  You mentioned that there were no new software installed before that happens.  Were there any hardware changes or updates?  If this isn't the case, we will perform a system restore to a point that you know that your system is working effectively.  Click HERE for the system restore instructions.
  Please let us know if it did or did not help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• "operations are underway. Please wait. The machine switches off automatically '-system never stops.

  Sometimes, when to stop Vista, instead of a normal shutdown, I get quite common background and a message reading: "operations are underway. Please wait. The machine switches off automatically. "The system then continues to run indefinitely, and I finally have to do an emergency stop. After the reboot, I then most of the time have to do a restore to an earlier point; Once in a great while, he'll tell me the test stops abnormally and charge really. Tried to figure what could be causing it and can't find a logical reason. Diagnosis never found anything, but there is not really anything in the windows which diagnosed something as a shutdown of the system.  Help.  It's boring.

  Hi Baron Stewart,

  (1) since when are you facing this problem?

  (2) remember to make changes?

  Method 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...)  Except the mouse and keyboard and then try to stop

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

  Method 2:  Select the boot and then check if the problem persists

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  
  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

  Method 3: check the logs in Event Viewer for more information on this problem

  Open event viewer

  What are the information in event logs? (Event Viewer)

• Cannot connect wireless or even turn on the wireless "switch" on my computer

  I recently installed a copy of Windows 7 Professional, yet the installation, I couldn't have the wireless network to connect to what either.  The first thing I noticed was that my wireless button (which is a touchscreen as a device on the top of my keyboard) was not on, can I turn it on, or do I not have the fn + f2 option.

  My computer is a HP Elitebook 8440p and regardless of what precedes, I proceeded to install drivers wireless on HP support site, they had to choose some and I ended up trying 3 which did not work.  I found a page of networking which showed these drivers wireless with a connection of sorts but closer examination revealed that the problem lied with simply turn on my wireless switch.

  LAN works fine (I'm here now) and the wireless switch control active if I turn on my any and hit him (orane to blue towers), but otherwise, I am astonished.  I don't think that the router is the problem, but it is a 'Fast' model... that's all I know at this point, although I'll try to find the type of exact model if its important.

  I think it's information pertienent, thank you for any help you can provide!

  My computer shows management I installed the drivers...

  In fact, I found the answer (I hope help you someone else with your post if the time is not lost)

  My wireless is fine, it turns off when I plug my ethernet cable.

  Appreciate the answer however.

• MuseJSAssert: Error calling the function switch: TypeError: undefined is not a function (assessment '$element .on this.')

  As usual I never update muse immediately incase of any question, however, a few days after the update (have not installed the update) I go on my site, this message appear out of no where "MuseJSAssert: error calling the function switch: TypeError: undefined is not a function (assessment ' this.)" ($element.sur ') ".

  So I decided to install the update and see, but the message would have still done appear then I wiped my server and download all my files to perhaps solve the problem of Javascript, and yet the message is still displayed.

  Note that this came from nowhere even tho I don't update my muse or uploaded to my FTP in days.

  My site entire is now totally useless after months in manufacturing.

  Can anyone help?

  The error on the sites is caused by having custom include the code that loads several different versions of jQuery. A single Web page should only have one.

  The redirect URL that fails intermittently. We actively work to diagnose and fix that, but which will not only cause these errors. Each Muse site contains a snippet of JavaScript that silently and automatically returns to use the version of jQuery that muse will be mailed to your host if the CA version is not available for some reason any.

  The problem is a number of customer sites have wrong incorporated several different versions of jQuery. When the CDN version is available, it is used. Unfortunately, when it is not available, an incompatible version loaded by the custom code or third-party widget is used and which translates these errors.

  Long term loading multiple versions of jQuery should be removed from the code or the third-party widgets on your site. In the short term, we will have solved CDN failure and these errors will disappear, but they return in the future if multiple copies of jQuery in the code no Adobe added to the page are not deleted.

• How to leave the virtual switch as a physical switch law in esxi 5?

  Hello.

  I have Esxi5 installed on a server with 3 physical network card (they are supported and found in Esxi) on that Esxi I installed a virtual-SIN (NexentaStor) machine. The first network adapter is connected to the router, the second network adapter is connected to a PC. DHCP is enabled on the router. Normally on a real switch all connected pc should automatically get an IP address from the server (router), or must be able to communicate when they have a fixed IP address. This does not work on the virtual switch. One of my virtual pc Gets an IP address in a range of false, and I can't connect a real PC at this switch

  2 questions:

  1. Should what settings I use in esxi5 to get virtual pc the good IP address?
     
  2. Is it possible to connect a real pc directly to the second NIC in my esxi server and use the virtual switch as a true switch? In this way, I can use the Gigabit Nic for a fast and direct connection to the virtual NAS and can connect to the internet via the switch?
     

  

  Any help would be appreciated

  Pieter

  ESXi does not NAT unlike VMware Server or Workstation/Fusion.

• Network management - only the virtual switch

  I installed latest ESXi 4 Update 1, which is available. I m running Active Directory LAB on several virtual servers Windows 2008 R2 and one of them acts as a router with RRAS role. I m creating 3 different subnets and one of them must be only virtual - no material connection NIC in the interface of ESXi´s it seems that I can't do this, while creating the new switch virtual it forces me to select NIC it becomes a problem, because if I use a virtual switch for Windows 2008 router has the physical NETWORK map It will come to mean that the cable is disconnected. And I need a virtual connection between virtual servers only, that they will be the single subnet between them and communication to physical clients will go through this router´s of Windows 2008 NIC that is not supposed to be physical.

  How can I archive with ESXi?

  You can create a vSwitch without attached Teddy.

  Do not select any NIC, or delete them after the creation of the vSwitch.

  André

• Cannot install VMware ESXi 4.1 "cannot find the image of the installed system.

  Started in iso ESXi 4.1 downloaded, burned on a CD, CD, go to the screens, press F11 to install.  Immediately get the following error:

  -

  ---

  The installation operation failed!

  The installation operation encountered a fatal error:

  Cannot find the image of the installed system.  This is due to the image being not mounted correctly or the CD-ROM not supported.

  -

  ---

  The material is a system of handcrafted with Intel DQ35JO Council, latest version of the BIOS, Intel E6850 CPU, 8 GB of RAM, 2 SATA drives.  I know this isn't on the list compatible but is a 'white box '.  I installed ESXi 3.5 on it in the past and got it working, and I saw other success stories with this Board/CPU.  Yes, I have activated the virtualization mode in the BIOS and powered down/up.

  Here is what I tried:

  -Redownload VMware-VMvisor-Installer - 4.1.0 - 260247.x86_64.iso to ensure that it was not corrupt (2 copies, against perfectly)

  --Also tried another drive (IDE) CDROM

  -Created a bootable USB using uNetBootin 4.7.1 and booted from it

  -Switched SATA setting in the BIOS from AHCI to IDE

  I get the same exact error.  I searched here and everywhere and don't find any reference to this error.

  Help - all do you offer for my next step?

  Have you had a previous vSphere installed on your system?

  I had the same error on my 'white box' (in fact, it is black).  I used to run esxi 4.0 (u2) on my Acer X 3300 (6 GB, Quad Core AMD Athlon II).  Controllor internal SATA is not supported, but it allows me to use the box for normal windows task and ESXi is sitting on a SDHC 4 GB flash card.

  When I started my freshly burned ESX4.1 cdrom, I got the same error.   I thought that the fact that maybe there was an existing install on my destination drive (the flash memory card), and that the CD could not perform an upgrade.

  So, I tried the upgrade path (first trying to utility of the host and the .xml error message).  After reading the manual, I did the upgrade from 4.0 to 4.1 using the device of vMA and I must say that esxi 4.1 works great on my white box.

  Then I suggest that you try upgrading and see how far that gets you.

  Good luck (and a beautiful weekend)

  Marino

• VMware View client silent install switches

  I am unable to find a doc who has all the silent install switches listed for installation of the vmware view client. I found this thread http://communities.vmware.com/message/924962 but it does not list what makes each switch and I need to remove the reboot. I use landesk for this to get out for our customers. Also is there anyway to also put in the default server view vmware with a switch without using Group Policy? Thanks for any help I get.

  http://OZTeK.blogspot.com/2009/07/VMware-view-client-silent-installation.html

  See you soon,.

  Oz

• MuseJSAssert: Error calling the function switch: ReferenceError: Spry is undefined.

  I started Muse today and he said there was an update available. I installed and then made a few small changes on my 5 page site. Then I exported the HTML code and uploaded to my server.

  But now when I try to navigate the site in Chrome, I get the following error message:

  MuseJSAssert: Error calling the function switch: ReferenceError: Spry is undefined.

  The only changes I made were adding text to a few pages and adding metadata to each page information and displaying HTML exported locally (before transfer) everything behaves as it should... an error message.

  Any ideas why its doing this? or, more importantly, any suggestions on how to stop it from doing this? He did not have that yesterday before get me these small changes.

  Here's the URL: www.gardensbytheseaursery.com

  Thanks in advance.

  Jake

  This error occurs if all of the files for the site that we downloaded.

  The 2.0 update includes numerous improvements in the generated HTML, CSS and JavaScript, so while you can directly changing only some pages, if you are using an external FTP client all the exported files, and the files must be downloaded. (The new built-in FTP support automatically only generates and download the files that have changed since the previous download.)

• How can I find the installed version of Firefox?

  How can I find the installed version of Firefox?

  You run v33 right now. But you can still check two ways

  • Click on the

    

    button-> then the help icon (?) then on Firefox

  • Type of topic: in the address bar

• Is it possible to get the option "Switch to tab" higher when you type in the awesome bar?

  Hello

  I am currently under the latest version of Aurora and although I really like it, there is one thing that has bothered me kind of. I am often under more than 100 tablets at once and all of them to find the desired search tab takes a long time, so I would like to use the function "Switch to tab", but more often than not, this option is very far down the list of suggestions, causing me to miss them. So I would like to know if it is possible for this option as one of the first suggestions, instead of putting down in the list.

  Thanks in advance,

  xMyth

  Hello xMyth, I don't know if that's exactly what you're looking for, however when you start your search in the address bar with % it will be limited to open compressed only...