Similar Questions

• Impossible to test, check, calibrate the card (PCI-6221) DAQ with MAX

  Hello

  We bought a PCI-6221 DAQ card and we have installed. However, it seems that the device is not recognized. First of all, it appears as a device in the PXI system then that is a PXI system. Then, I don't have access to the 'properties', 'self test' and "to calibrate" menu. This issue should be linked to the first.

  I tried to remove the driver and install it again, but it didn't work, so I tried the update but it is the latest version. Is there a problem with the driver?

  I checked with Labview if it was possible to use it, but no devices were found by the DAQ assistant. We have the whole NI Developer Suite 2009.

  Thank you for your time

  Cedric THOMAS

  Hello

  It works! Great! Thank you very much for your help.

  However, does this mean that DAQmx 8.8 is having trouble with the PCI-6221 device? Or I made a mistake during installation (but I have followed the manual)...

  I even can I create a simulated device also. That I couldn't do before with MAX 4.5.

  Thank you

  Cedric

• Synchronize the clocks of PCI I / AO with multiple AI in parallel

  I want to synchronize my HAVE and AO to run on the same clock and have my AO beginning with a relaxation from the beginning of IT.  All works beautifully except when I have another process running in parallel.  I use the cDAQ chassis 9178 and I have a low resolution HERE (9201) that runs in the context of monitoring for alarm conditions.  I want to run in parallel to my DAQ vi.

  In the vi DAQ begins AI (9222) and triggers the AO (9263), the AO clock is referenced to Dev1/AI/SampleClock and start trigger is referenced to/Dev1/I/StartTrigger

  The problem seems to be that if the 9201 collects data HAVE then my AO is actually running at that frequency of clock instead of the 9222 (since the 9201 is always launched in the background, the OD has seen this first)

  How can I tell the AO (9263) to run with the AI 9222 clock and trigger rather than the AI 9201?  I think that I do not understand how the chassis works with modules...

  Gracias.

  Hello Telleurium,

  The quick answer is call specifically on the timing engine and relaxation of timing engine. This will ensure that the 9263 and the 9222 are synchronized. Please take a look at the example below what I call specifically on the timing engineof teo.

  

  A more detailed explanaiton of what happens is that the 9201 seizing first the timing of AI engine (which means that it is now associated with the AI and AI trigger sample clock) so you see the 9263 is synchronized with the 9201.

  Best regards

  Izzy O.

  Technical sales engineer

  National Instruments

  www.NI.com/support

  P.S. on further notice, that it would probably be easier to point the 9201 on a different timing engine.

• I need to generate 3.3 V logic level Digital train of pulses with the NI PCI-6221. Can I change the level of 6221 OR logic output?

  I need to generate 3.3 V logic level Digital train of pulses with the NI PCI-6221. Can I change the level of 6221 OR logic output?

  The output cannot be changed. 5V to 3, 3V level controllers are readily available (Maxim, I think). As long as the scanning speed (etc.) is fast enough for your pulse train, even 3, 3V regulator would work. I don't know if NEITHER offers a module to condition TTL levels.

• WHT is the downside of the scope with respect to the operation?

  WHT is the downside of the scope with respect to the operation?

  not 100% sure I understand your question well, but scope is available for the duration of your request - which means that if you insert data in the scope it remains around the life of your application - which can be a drain on resources.

• The use of knowledge check with sanitation?

  Our courses are set up so that the quiz questions act as knowledge checks throughout.  For example, we have a course with 20 slides, with a quiz question each slide that will remedy a previous slide if the answer is incorrect.  The problem is that scope quiz once, slides between the slides 'return to the quiz' and the next quiz question are to be ignored.

  What we have discovered is that once the student is in the scope of quizzes (after the first control of knowledge), Captivate you go directly to the next quiz question when the student arrives on a slide that contains an action for success of the «back to the quiz»

  For example:

  Slide 1	Slide 2	Slide 3	Slide 4	Slide 5	Slide 6...
  Text slide	Quiz question 1	Text slide	Slide text sanitation	Text slide	Quiz question 2
  Action = next slide	Action = next slide	Action = next slide	Action = back to the Quiz	Action = next slide	Action = next slide
  inQuizScope = False	inQuizScope = True	inQuizScope = True	inQuizScope = True	inQuizScope = True	inQuizScope = True

  In this example, slide 4 is the sanitation for the quiz question slide 2.  Slide 5 is to be ignored during the progression of courses (starting at slide 1 and progressing along the whole time), because the student is brought quiz slide 4 is seen.  In this case, by selecting the 'next' button triggers the 'back to the quiz' operation and causes the course proceed directly to the next quiz question (slide 6).

  Our workaround for this has been to add additional slides for sanitation at the end of the course, which can only be accessed from the questions on the quiz, but that seems to be additional work and is not very elegant.

  Someone at - he found a way to sanitation between quiz questions without skipping the blades once within reach of quiz?

  The only way I can think of is to use variables and actions to follow the slides had been seen so that if a question has been reached before the slide before it had been consulted, then it would jump to that slide.  But this solution would require some work and would not necessarily more "elegant" you have solution.

• Install the Mini PCI wireless network card. Need help!

  Hello
  I have laptop Toshiba 5200-701 which is upgradble of wireless network, so I bought the mini PCI card Philips wireless brand. The reference is PH12127-E/PH11107-E and support 802.11a/b/g network address MAC 00 4F 05 43 88 F4.
  When I inserted the card in the laptop it shows new hardware found and then I downloaded website IBM software since I was told that this card is basically designed for laptop IBM, however, my laptop is unable to install the software and still facing problem... so please could someone help.
  Thank you very much.

  Moral salvation

  Well, in my opinion, you bought a bad wireless card. I don t think that your game can works with your device. Before you buy some hardware components, you need to check the compatibility of these parts. Toshiba service partners always have information about the units on the right. However, I found a wireless card that is compatible with your laptop. It's a PA3212U-1MPC.

  Good bye

• Location of the Mini PCI Slot on Satellite P10

  Hi - I have a portable series of P10, PSP10E-0RCJM-EN.

  It is initially provided without an internal WIFI card but a swith and LED indicator.

  I hope to fit a suitable Mini PCI card.

  I am likely to find that an antenna is already installed?

  That more can someone guide me as to where is the slot mini pci and how to access it please?

  I read the previous posts about the contacts of masking/insulation on the card wifi on this and other forums, so I'm ready for this problem when I get there.

  I hope you can help, impatience of someone soon!

  Graham

  Hello

  The wireless network card is an option on this unit. It is possible to switch this unit with the WLan card. The WiFi antenna should already be included in the specifications.
  The WLan pci slot, you will find at the bottom of the unit.
  It s close to the slot of the modem.
  However, I would recommend consultation with the user manual. There you should find more details.

• Satellite Pro M10 - location of the mini-pci slot?

  Hello

  I have a M10 Pro of the Satellite with a mini-PCI Intel Pro 2100. Now, I wanted to put in a new card, but I can't find the mini-pci slot? I opened all the way down, but there nothing. Where is it located and what is the best way to open the laptop? I guess a lot of screws must come out...

  Hello

  Well, as far as I know the mini-PCI card is under the keyboard. In this case, you will need to remove the unit covers. But if you open Notepad, you will lose the warranty.
  In my opinion, you should contact the ASP for help and detailed descriptions.

  Good bye

• Satellite A100-028 - How to replace the mini-PCI WiFi card?

  Hello

  I want to replace the Intel with a Module Atheros wireless card.
  Unfortunately on the background there is no cover for the mini PCI Slot.
  Where he is? I guess that they are under the top cover or under the keyboard.
  Should I a short "How To" in this way:
  Which screws I release that covers and so on are to be released.

  Thanks in advance.

  Hi Galdor,

  It of not simple to change the W - Lan card.
  The card ist under the keyboard and under the top cover.
  You have to disassemble the entire and when you do that you lose your warranty.
  I think it's the best for you to contakt a service point for this work.

  Greet
  Thorsten

• PCI/4070 Flexdmm with Windows 7

  See the datasheet shows Vista/XP Compatible and has been wondering if puts up-to-date or another gives Windows 7 compatibility? Thank you

  The latest NI-DMM driver is version 3.0.5 which will work with the PXI/PCI-4070 and works with Windows 7. It is available for download here:

  NOR-DMM 3.0.5-Windows Server 2003 R2, 32-bit/XP 32-bit/Server 2008 R2 64-bit/Vista/7

  Hardware devices (DMM) to support the hardware and the software requirements are listed in the Readme of the driver download page.

• the NI PCI-6023E tarjeta not me appears en max

  The NI PCI -6023E no abilitada en appears don't MAX y cuando quiero instalar el driver me pide a 2 CD el cual no tengo, bajo el driver Windows 7 USO y cuando el solo este link CD1 appears

  
  

  http://www.NI.com/download/NI-DAQmx-7.3/369/en/

  
  

  Espero para me help can achieve instalar con exito el driver

  
  

  Gracias

  Hola;

  Primero that nada; You version of LabVIEW no esta soportada para Windows 7; Sino hasta 2009 sp1 version. ES posible that LabVIEW no h. esperas como, por lo you recomendaria fornuis you version.

  Compatibility of the versions of Windows with LabVIEW

  Version mas actual than puedes instalar DAQmx are the LV 8.5 9.3 para Windows 7 y puedes descargar Aquí.

  EXITO

• PCIe-653 x with DAQ traditional

  Hello

  We want to update some of our network using a PCIe-6536. Is it possible to run this card with traditional NIDAQ?

  Does anyone have experience with the PCIe-653 x with DAQ traditional. Or is it only possible to run this card with DAQmx?

  Greetings

  Oliver

  Hi Oliver,.

  PCIe cards not are usually not supported by the old traditional DAQ driver.

  In any case, you should consider updating your application to DAQmx as TRANS. data acquisition support is quite limited (see also the official statement of OR below)

  "Caveat ".  NOR-traditional DAQ
  (Legacy) is an older driver with the obsolete application programming
  interfaces
  (API) for the development of acquisition data, instrumentation and control
  requests for former of National Instruments DAQ devices. You must use
  NOR-DAQ traditional (old) that in some circumstances. Refer to the
  File Readme of NOR-DAQ for a glimpse of the two API NOR-DAQ, the
  benefits of
  NOR-DAQmx and more information about when to use NOR-traditional DAQ
  (Legacy)
  including a complete list of devices supported, operating systems,
  application
  versions of the software and the language versions. You can install the most recent
  version of
  NOR-DAQmx software, available at ni.com/downloads.
  "

  Kind regards
  Bernd

• Calendar and the problems of data collection with the DAQ Assistant

  Hello NOR Developer area,

  I am a Novice of LabVIEW and have seen how helpful you all can be, and if I come to ask for your help.

  I'm having some trouble with a VI I built that specifies an input voltage, a SCB - 100 connected to a PCI-6031E and converts this tension in a temperature displayed on a waveform table. The goal is to give a constant reading of the temperature and display it in a chart for as long that the VI is running (and to reset the chart the next time the tracks of VI).

  The problems I've encountered currently are:

  -After a few minutes of the VI running, I get an error message 200279: tried to read samples that are no longer available. The requested sample was already available, but has since been replaced. (to the DAQ Assistant express VI).

  -I don't know how to change my chart so that the minimum value X is both during which the VI was launched and have the maximum X value increases with each iteration of the loop. Currently, I have the VI get the time system and contributing to the property node X scale. This worked for the graph of the voltage, but not for the temperature chart

  I appreciate those of you who took the time to read my post.

  Thank you all for your help.

  Sincerely,

  Ethan A. Klein

  SB candidate in Chemistry & Physics

  Massachusetts Institute of Technology

  Class of 2015

  PS I enclose my VI to give you a better understanding of my current situation.

  E A Klein wrote:

  Thanks for writing.

  What property node is talking?
  I do not understand that many different data types. How can I go on the treatment of all the data?

  (Did you mean I should wire 'blue' data for mathematical functions rather than using the node property tension?)

  Sincerely,

  In fact, one of the nodes property.  I mean specifically the tension property node.  But in reviewing, I noticed the other nodes in property for the chart.  Just set auto-scaling to the X scale and that should take care of two of the nodes property (right click on the graph, X scale-> AutoScale X Scale).  I also recommend placing your mathematical functions in a Subvi to make things easier to read.  Attached, that's what I think you're after.

  I hope that these small tweaks will speed things up enough to avoid your error.  If this isn't the case, then we should begin to look at the design of producer/consumer model or take readings at the same time.  It might also be worth looking away the DAQ Assistant and DAQmx real screws.  But one step at a time.

• What is the analog input of the NI PCI-6229 impedance?

  I am trying to determine the effect of a 12 K resistor that is in series with an analog input of an NI PCI-6229 data acquisition card.  Resistance of 12K seems to be part of a RC filter.  I have a 0-10 VDC source this supply circuit.  What is the impedance of the analog input of the NI PCI-6229 data acquisition card?  If it makes any difference, the analog input is connected in differential mode with a 180K resistor to Gnd AI.

  Thank you

  RWB

  Hi, RWB,.

  The input impedance is classified in the specifications 10 GOhm.  So, the effect of your k 12 resistance should be relatively low.  Take care!