The parallel model configuration help

Similar Questions

• Equivalent of PreUUTLoop for the parallel model

  I am building a test sequence to test two DUT in parallel, on a station where some of the facilities will be shared.  I want to initialize all the equipment BEFORE the start of the exectuion of tests and even more specifically before the individual PreUUT of each execution taken step.

  It was logical to my approach "Initialize hardware" in the "PreUUTLoop" sequence reminder in an original design that used the sequential model. It must only be done once.

  Is there a reminder of similar sequence in the parallel model in which I can move step 'initialize hardware "?

  I put in the SequenceFileLoad callback.

• Monitoring with parallel model of global state?

  Hi all

  This can be a very simple question, I am new to TS, please excuse my lack of knowledge!

  I use the parallel model TestStand to test 16 individual DUT. I nailed pretty well parallel processes, but I'm trying to find a way to 'monitor' the global settings of the system.

  For example, some sensors global X defines a Boolean value if something happens (pressure lost etc.) How can I detect this boolean change and do something in response? I monitor the Boolean value in the execution of each thread?

  Thanks in advance for the help!

  Hi André,.

  You can create a sequence of void.

  Enter the void sequence in a new thread so that it runs in parallel.

  You will need to use a type of appeal to that effect sequence step.

  Few things you should take care:

  Ensure that the above step works only for a power outlet.

  Ensure that this thread is closed at the end before the end of the sequence main (you can use variables fileglobal as flags for the communication between the thread and the main sequence or the notification procedure)

  I hope this helps.

  Ravi

• Configuration of the two of the same model data acquisition

  Hello, community of NOR.

  I'm an intern in mechanical engineering with experience in base with LabVIEW.

  I would like to speak to OR directly on this issue, but I don't have a service contract and my company wants me to understand this before you buy LabVIEW.

  I hope that someone has experience about my question, and I would be very happy to help.

  We intend on purchasing an expansion card for our acquisition of data (OMB-USB-2416), but unfortunately it is offline and no custom would not happen in time.

  So, I need LabVIEW to read voltage HAVE two of the same model of data acquisition, which would amount to about 30 channels.

  Is this possible with LabVIEW?

  Thank you.

  Measurement computing says that the "physical channels" dropdown list is automatically filled in once both devices are configured.

• There is a configuration option that allows the parallel execution of sub vi?

  I'm trying to run a vi in teststand has two parallel execution paths. A path under vi implements the trigger and wait for data from a module scope, while in the other lane, I'm starting a power supply. The power waits until the scope is armed and runs.

  It works as a standalone vi. When I try to run this vi in teststand he works the first vi scope and then runs the power supply. Of course vi opportunities get to expiration and outputs and data are not met.

  I tried a number of methods of synchronization, and although they seem to work standalone, as soon as I try them in Testsatnd I have this problem.

  I am new to teststand and I was wondering if there is some configuration config I missed which allows a vi like this to run as he's independent.

  I have a number of simple screws that run as planned, but this one left me speechless.

  I had to split these screws but would really prefer to have them in the same vi.

  (The latest versions of teststand and Labview running)

  Henry

  hkroker,

  It is a known problem. Please refer to the following KB to help solve your problem.

  - Parallel blocks run sequentially why does my LabVIEW VI when it is called from TestStand?

  Concerning

  Anand jegou

  National Instruments

• Need urgent help! In my Vision Application, how to extract the parameters of the geometric model specified curve was generated by the template editor OR?

  I have an application of machine vision, in which the geometric pattern match technique was used to find the target in the images of type variant.

  as we know, we do a geometric model by model OR editor in the editor we can adjust the parameters of the curve specified settings to get the desired curves and we derive the custom box to ignore during the match. then we save the use of the same model in our application of vision.

  Now my question is coming. When I program my request for the geometric game. I have specified the parameters of the curve for the entrance of the IMAQ Advanced Setup learn ringtone 2, of course, I have to adjust this identical to the model, but I don't know how we extract the geometric model. I tried all the methods, for example, I can read data custom, IMAQ get characteristics of the geometric model(it's just for the basic functionality? so is there even a VI based edge?), even at anasys PNG file formats! But I can't read the info of the geometric model by myself!

  It is also illogical to adjust the CURVE SETTINGS manually again for the " IMAQ Advanced Setup Learn Pattern 2" after that I already have in the template editor OR!

  Hello

  Why do you need to specify the curve settings once again, if you have already built a model using the template editor? You don't need to use "IMAQ Advanced Setup learn geometric model 2 VI" to find games (see the attached example).

  You can wire the 'curve settings' control to 'IMAQ configuration geometrical game model 2 VI', but the values are not used if wire you a Boolean true to the node "use learning curve settings" (it's like that by default). To prove it, I enclose a small program with pre-created model (using the template editor) for a geometrical alignment. The model and the test of three images are also included.

  Try changing the settings of the curve with the 'use know curve settings' enabled, and you will see the corresponding score remains the same. Disable the Boolean control, then try to change the curve settings.

  Also take a look at the detailed help for "IMAQ configuration geometrical game model 2 VI", specifically the "learning curve parameters of use."

  I hope this helps.

  Best regards

  K

• I have a mac book pro 2009 model, now when I try to load it, there is no green light on the adapter and the laptop does not charge. Not sure if there is a problem with the card or the battery or the laptop. Kindly help

  I have a Mac book pro 2009 model, when I try to load it it not there no green light on the adapter and he is in charge. Not sure if there is a problem with the adapter or the battery or the laptop. Kindly help... Thank you

  Have you tried:

  Portable Apple computers: Troubleshooting MagSafe adapters - Apple Support

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

• I replace my airport express with the new model. Flashing orange. It works, but cannot configure security. Tried to reset via the reset button.

  I replace my airport express with the new model. Flashing orange. It works, but cannot configure security. Tried to reset via the reset button. Tried unplugging and tried unplugging the modem. I would like to fix.

  Modem... doing and... model number you have?

  What operating system do you use on your Mac, or you are using an iPhone or iPad set things up... or a PC?

• With the help of control and simulation module; e to get the time the MISO model Manager

  Hello

  Please can someone show me how to find the response time of the system below using the module control and simulation?

  (y (k) - 1,7407 y (k-1) + 0.6236y (k-2) + 0.1782y (k-3)) =-0.0932 u(k-1) + e (k)

  where there is out, u came and e is a white noise.

  I tried to enter the CD construct MIMO model, then connect it to CD response time. * s vi.

  But what I really need to enter the model coeffs every time? and I still don't see the answer!

  Help, please...

  Kind regards

  ruser

  Hello

  you have the correct image... I used the Toolbox ID sys (Assistant)... to estimate the system model...

  and I tried all week last get the model of my system in labview for use the control on this module.

  Alhamdulillah...

  I ended up doing... I saved the template to a file from the Toolbox id sys... (my model is in discrete form) then I loaded it in labview using load file pattern...

  so now I in labview...

  now for control parts... ..

  Thank you again...

  ruser.

• My laptop is one of the 4 home cannot connect to the internet, it's Vista and it has connected w/Ethernet no problem, I called Xfinity tech, that says, is the problem of configuration! Can you help me?

  Acer laptop, Vista is, she can connect wirelessly with my friend modem but my house, she can't, I use the service of Comcast, they checked the modem is fine, they think that the problem of configuration! I'm not computer too, thank you!

  Ryan (Shih Chi)

  Hello

  How do you try to connect the computer to the House? Wired
  or wireless?
  Try the methods provided and see if it helps to solve the problem.
  Method 1:
  Check out the link and follow the troubleshooting steps in the article.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
   
  Method 2:
  If you try to connect to t Wireless net work then refer to this link and follow the steps.
  Connect to a network with Windows Vista wireless
  http://TechNet.Microsoft.com/en-us/library/bb878035.aspx
   
  Method 3:
  Reset TCP/IP on your computer and check. Check out the link and follow the steps.
  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357
   
  Method 4:
  You can also visit this link and follow the steps.
  
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us
   
  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/ ) how to back up and restore the registry in Windows

• Help! I can't find the number/model number series/number for my printer!

  To fix a printer problem, it is often very important to know exactly which printer you are using and usually just 'Photosmart', 'Envy', or 'Laserjet' is not enough to narrow the possible diagnosis. Same different generations of the same model can use different hardware or software. While HP put this info in several places to find this info can sometimes be difficult or close to impossible if you don't know where to look, or what you are looking for. Watch this video to locate all of the above.

  If you need help to try one of these links on your specific printer family:

  Deskjets

  http://support.HP.com/us-en/document/c01105883

  Want to series

  http://support.HP.com/us-en/document/c01105892

  LaserJet

  http://support.HP.com/us-en/document/c01230412

  Officejets

  http://support.HP.com/us-en/document/buu04090

  Photosmarts

  http://support.HP.com/us-en/document/c01105892

  PSC

  http://support.HP.com/us-en/document/buu04090

  If you have any questions or concerns do not hesitate to ask!

  Good luck!

• How can I import tables to a different schema in the relational model existing... to add these tables in the existing model? PLSS help

  How can I import tables from a different schema in the relational model... to add these tables in the existing relational/logic model? PLSS help

  Notes; I already have a schema ready relational/logic model... and I need to add more tables to this relational/logic model

  can I import the same way like I did before?

  But even if I do the same how can I add it in the template? as the logic model has been designed...

  Help, please...

  Thank you

  To view the diagram of logic model in Bachman notation, you right-click on a blank area of the diagram and select the rating > Bachman Notation.

  David

• I just bought a new computer and I was wondering that if I were to do something like unistall Creative Cloud/PS and LR to my old model to the new model I'd appreciate any help (real) Thanx Jimi

  I just bought a new computer and I was wondering that if I were to do something like unistall Creative Cloud/PS and LR to my old model to the new model I'd appreciate any help (real) Thanx Jimi

  Cloud license allows 2 activations http://www.adobe.com/legal/licenses-terms.html

  -Install on a 2nd computer http://forums.adobe.com/thread/1452292?tstart=0

  -Windows or Mac has no importance... 2 on the same operating system or 1 on each

  -Two activations may NOT be used at the same time (noted in the link above of the license)

  IF you won't use the old computer...

  Remove the license on a computer http://forums.adobe.com/thread/1442423?tstart=0 can help

  -read http://helpx.adobe.com/x-productkb/policy-pricing/error-maxium-acitvation-exceeded.html

  -or https://helpx.adobe.com/x-productkb/policy-pricing/activate-deactivate-products.html

• Moving the virtual computer configuration file and work on the clone of the model

  Using the VirtualMachineRelocateSpecDiskLocator to move disks from different NFS data warehouses when cloning a model looks very good work.  However, the Virtual Machine configuration file and the location of work remain on their original NFS data storage, not moving with the root of the drive.

  If this move not all together, or am I missing a step here?

  Thank you

  Scott

  Specifying the "data store" in VirtualMachineRelocateSpecDiskLocator specifies the location of the VM virtual disks only. To move the virtual machine, it might also be necessary to specify "datastore" property of "VirtualMachineRelocateSpec. If this is not specified, the current data store is used to store the files of the virtual computer.

• After trying to use Fix - It to fix XP does not recognize the USB key, had to go back to the last good configuration and computer charge always VERY slowly. What's past and how to fix it?

  Windows XP SP3 has ceased to recognize a USB flash drive and card reader that he always acknowledged in the past. I tried to use Fix - It to correct the problem. Fix - It is then asked to restart the computer. When the computer is restarted, it would not load. After waiting almost two hours, I restarted with the last good configuration. Then reloaded, it took nearly an hour. Before using the Fix - It, the computer was loading in less than five minutes after a reboot. There a lot of things on it. What can I do now to solve the problem posed by Fix - It and also correct the problem with XP recognizes does not flash drives?

  Hi lental,

  ·         Have what fixit you tried?

  ·         Do you have an error message when you try to start the computer in normal mode?

  ·         What is the brand and model of the computer?

  ·         You're able to boot in safe mode?

  Follow these methods.

  Method 1: Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 2: Follow the steps in the article.

  Advanced Troubleshooting for General startup problems in Windows XP

  Method 3: Follow the steps in the article to resolve the problem of USB.

  A computer that is running Windows XP cannot detect a USB, an Apple iPod flash drive or an external hard disk drive

  Advanced troubleshooting tips for General USB for Windows XP problems

  For reference:

  How to make a computer faster: 6 ways to speed up your PC

  Slow PC? Optimize your computer for peak performance