The queue limit in CS4 Capture HDV

Similar Questions

• Evacuation of the queues on Cisco 6504-E and 6509-E Cisco line cards

  Hello

  In our network environment, we get the following configuration:

  Cisco 6509-E(Sup-2T) as the main switch equipped of line card module WS-X 6848-SFP (1 GE)

  Cisco 6504-E (VSS-720-10 G Sup) as long as the service of distribution layer switch equipped WS-X 6704-10GE line card module

  .

  Time modules line cards end Layer 3 connections from the layer of access/core.

  The QoS trust status is ""DSCP ' on line card interfaces and 6504-E 'mls qos trust dscp' is explicitly configured to trust the DSCP values. "           As is clear from interface capacity output below, "QoS queueuing" mode on both cards line is "CoS" only, and DSCP evacuation lines is not available in interface ' wrr-tail ' configurations. Similar problem exists on the interfaces of channel member of port on the main switch Sup - 2 t as well.

  CORE01 #sh int gig2/1 cap

  GigabitEthernet2/1

  Model: WS - X SFP-6848

  Type: 1000BaseSX

  QOS scheduling: rx-(2q8t), tx-(1p3q8t)

  Queueing QOS mode: rx-(cos), tx-(cos)

  VSS01 #sh int t1/2/1 cap

  TenGigabitEthernet1/2/1

  Model: WS - X 6704-10GE

  Type: 10Gbase-LR

  QOS scheduling: rx-(8q8t), tx-(1p7q8t)

  Queueing QOS mode: rx-(cos), tx-(cos)

  CORE01(Config-if) #wrr - queue?

  minimum bandwidth of WRR bandwidth set with weights or percentages

  cos-map set up cos-sheet for a queue threshold ---> Cos map only no. DSCP

  the queue limit configure the queue limit

  detection of random set up the random detection

  the bandwidth of the SRR maximum queue set up with weights of form or

  percentages

  tail-drop threshold thresholds configure queue

  VSS01(Config-if) #wrr - queue?

  minimum bandwidth of WRR bandwidth set with weights or percentages

  COS-map set up cos-sheet for a queue threshold---> Cos only no. DSCP map

  the queue limit configure the queue limit

  detection of random set up the random detection

  tail-drop threshold thresholds configure queue

  In the above scenario, how the evacuation of the queues should be applied and what are best practices? If 'wrr-tail' is not supported for DSCP, it's recommended to set up "Political map" for evacuation queues and/or any other configuration of queues and then apply the policy of the outgoing evacuation on the interface function. Also, if the queue of political output card config is used, this allows for all the other DSCP / COS line cards in the system, so that the configuration is compatible with the network of 6500.

  Thank you and best regards,

  Mohan

  :

  Disclaimer

  The author of this announcement offers the information in this publication without compensation and with the understanding of the reader that there is no implicit or explicit adequacy or adaptation to any purpose.  Information provided is for information purposes only and should not be interpreted as making the professional advice of any kind. Use information from this announcement is only at risk of the reader.

  RESPONSIBILITY

  Any author will be responsible for any damage that it (including, without limitation, damages for loss of use, data or profits) arising out of the use or inability to use the information in the view even if author has been advised of the possibility of such damages.

  Poster

  My understanding is that you use wrr-queue cos-card as you would be for the CoS values understand the DSCP values have been mapped in these CoS values.

  If you look at figure 2-25, in the reference I provided, you will see 'Final internal DSCP is mapped to CoS' and ' "DSCP-CoS > rewrite" when dealing with exit port QoS. "

• CS4 does not recognize the MPG files that it captured previously

  Hello

  I have spent some time in the knowledge base and search the Forum, but don't see anything that could help me.

  Windows 7 64-bit on Intel I - 7 920 quad 12 GB of ram CS4 version 4.2.1.  This problem developed there months after installing the suite CS.  Other than what is explained here, there were no changes to the operating system or CS4.

  The problem is that CS4 has ceased to recognize imported MPG files to a HDV camera about a month, using the PrPro capture utility (F5?).  These files have been imported into the project and then treatment Panel (MIC, effects, etc.) on a 64 THAT HDV preset timeline minute.  The entire sequence has been made and read successfully.

  After completing the sequence, I exported it with SOUL to create the elementals of blue ray MPEG to add in yet.  The TEA code finished without obvious mistake.

  Then I created a project again and tried to add the asset - an audio and a video file.  The audio file is added without problem.  Importing video files failed 99% with encorr and Windows hung.  Power off required stop.

  Suspecting a problem with the video file, I open the video file in Windows Media Player and it played ok.  (I note here that this was the first time on this machine that I used WMP, and he did a few configuration steps?)

  I tried yet again without success.  At the next reboot, I open the windows task manager and placed on the second screen so I could watch the CPU to use.  The use of the CPU ran 3 to 8% but when still hung, grew the Task Manager

  I have uninstalled and reinstalled again and SOUL and then upgraded for current levels of the rev.  Same answer as before.

  Based on a post on the site again, I deleted the cache of media key in the registry and rebooted.  Always without success.

  At this point, I decided to see if one of these manipulations had affected the PrPro project.  The project, the sequence and the project Panel all come up as before.  However, all the MPG files were marked OFFLINE.  AVI files and PSD image files were unaffected - they remain linked. These files are all on the HARD disk in the PC itself - no removable disks or network

  I tried to re bind the file by clicking on the main capture file, but each attempt resulted in the error message "unsupported format". or corrupted file.

  Using WMP, I found that the files were not damaged.  I also confirmed that ADobe had recreated the media cache keys and was in fact identified files files.

  I tried to reimport the original capture file and received the same error message.

  I have paid full CS4 and I confirmed that I had options MPEG, when I created a new project.

  For now, I'm more interested fixed the PrPro reason no longers recognizes MPG files he captured, processed and made yesterday. I will fight the problem still on this site.

  Everyone knows this or can make a suggestion how to fix this?

  I do not see why reinstall again and SOUL would have caused this.  I can suspect WMP.  Where can I find which codecs are charged and their priority? What is the codec for prpro would look? MainConcept?

  I intend to use Gspot to see this as code mpg files - need the codec used by adobe.

  Any help you give would be appreciated.

  I can help you with one of those - project files/folders are intact. I am paranoid that I save things like that, even if they should not be affected in some way.

  Like the Adobe Clean Script, run several times is designed to eliminate all things Adobe CS4, I don't know how it might affect the other Adobe programs in a suite. Maybe others can give you a definitive answer.

  I also usually recommend run a cleaner registry, like CCleaner (and to let the default registry backup first), before the reinstall. IIRC, a user had a problem with him, but could have been OE, as most of the users here swear by it, and I've never had a problem (always do the backup of the registry but).

  Good luck and sorry for the bad news. Maybe someone from Adobe can shed more light on why, but I have yet to hear of what happens with CS5, so maybe all that has allowed the reversion has been fixed.

  Furthermore, it seems important to make all updates immediately after reinstalling, before launching the program. It is in any case the recommendation.

  Hunt

• Why "limit maximum instances of this event in the queue" in the dialog box change events?

  Why I "would limit the maximum instances of this event in the queue" in the dialog box change events?

  

  I think that this is new for LV 2014, but I couldn't find an explanation for an instance of good use. A research on OR displays only the 2014 help text, which explains what it does, but not why?

  Does anyone know good arguments to use this option?

  Thanks in advance.

  Justin Tyme

  

  It is useful for user interface elements that can enqueue actions as quickly as they can be made.

  For example, say it takes takes 1 second to take a picture and save it. The user presses the button "Take a photo", but they do not see a new image file again after a wait of 250 ms (human beings humans can be impatient) so they press twice. Finally, they see a new file image... and then another... and then another... To get rid of this possibility, check this box.

  Or that you have a cursor to adjust some settings. Moving the cursor updates very fast! If the user swipes from 0 to 1 then the program might try to send all the rest as a parameter to your instrument, which takes some time. Instead of sending all of these values, it is probably better if the software can keep up with the cursor and send a value of about 1 at the same time, the cursor said 1. If you do not check this box, the user can be 1, but the unit will continue to receive values from 0.53, 0.54, 0.55...

• CS6 Capture HDV however no video does appear in the order

  Aloha all,.

  I wonder what I'm doing wrong... I opened the capture, the camera is online and remote control works, I indicate to capture the 'band' in the area of long-shoring, I hit the record button and the device renders the video, timecode of the point begins to register but timecode of the captured quantity begins to roll and when the capture is finished, there is no video.

  I checked and re-checked the unicameral connections and if I had a bad cord or bad device connection control does not work and the camera would not be recognized, so I then went to my video card to see if there is a setting I have to do and there is nothing to do... I'm totally lost, what I am doing wrong?

  Mahalo-n-aloha... konadon

  HDV camcorders offer "downconversion" DV on the 1394 output when you listen HDV recordings. If your recording is HDV, but you can only capture it as DV, so that's the question. In addition, if you have the control of bridge and timecode but no video, indicates the same question. In the menu of the camera, turn off the function "convert i.Link" and also set VTR "HDV", rather than "DV" or "Auto".

  With the camera off, unplug the cable to the computer 1394, close App edition. reconnect 1394 PC should recognize the camera and the camera (in playback mode). Then you can start the first and should be able to capture HDV.

  Jeff Pulera

  Safe Harbor computers

• Premiere Pro CS4 - audio not listed is not in the queue of Media Encoder

  Hey all,.

  The title says it all. I have two audio files from Premiere Pro CS4 both with the extension WAV. When I go to them for export as a media, Media Encoder does not seem to take it to the top and the queue window remains empty.  I had no problem with video files, but this is my first time needing to encode audio files strictly.

  Is there a trick?  I need to encode to MP3 or WAV. Any ideas?

  Thanks for the tips.

  Ok.

  Couple of notes.  A re-export off Soundbooth as .wav files, .mp3 is not.  Two, you do not mention the details of any sequence could have created and been working in.

• Can I change SD and HDV sequences at the same time in CS4?

  I have a camcorder Sony PD 150 and I am looking to buy a Sony HDR - HC # HDV 1080i Camcorder to use as a second video camera shoots.  Can I edit images from two cameras on the same timeline in CS4?    I use a PC, Windows XP Home Edition, Version 2002, with a processor Intel (R) Pentium (R) 2.80 GB 2.5 GB of RAM.  Thank you!

  Lewis B.

  With your processor, I suggest you downrez in HDV, DV camera and change only in SD and deliver on DVD or similar.

  If you want to make HDV, get a better PC, invest in InstantHD Pro of S.redgiant to uprez your DV material (and you can still be disappointed by the results) and get a reader and burner BRD.

• How to get Premiere Pro CS4 rendering HDV again?

  Embarrassing problem:

  Use PP CS4 (as part of the master collection) for several months, no problem. Details of the system below. This morning, I made a 1 HR 1080i HDV sequences 29.97df (AVCHD, Blu - ray) m4v format. I've done many other makes this same sequence, with no problems (MPEG 2, etc.). Completed successfully rendering. So, I decided that I would study the output and possibly adjust the brightness. I tried to import the PP. any sequence, he showed as a screen orange without video or audio. I assumed that this meant that the PP could not interpret the video rendering, which seemed strange (it seemed to be a reasonable-AVCHD with audio PCM format).

  Like it wasn't a big problem, I simply deleted the imported clip and decided to make an another record in HDV MPEG-2 format. (I have I'm going to do a standard DVD also and wanted images MPEG-2.) I started to export standard (MPEG-2 1 - pass VBR with 384K audio preset, even the one I had used many times before) and nothing happened. Adobe Media Encoder hung on the first image with no progress. I tried to stop the queue and delete current file. SOUL hanging there. I had to use the Task Manager to kill him. I then closed PP and rebooted the system. Open pp with sequence again and I tried export again in the same way. Same results.

  I tried a few times with different preset settings - whenever TEA would hang and he made no progress. Whenever I couldn't cancel, but had to kill using Task Manager.

  Then, I decided to do a new rendering part of the sequence just to see if that would make a difference. I put a small bench and deleted the files of rendering by using the option menu sequence. A red lines as expected. Sequence hit + effects on a work area. Nothing. Render hung with 0.02% full. Tried to cancel. No dice. You have to use the Task Manager to kill PP.

  Tried a bunch of times with different segments of the sequence. Every time I did, I would be cleanly restart the system to ensure that nothing has been left in a strange state.

  If at this point, I could not export or go to MPEG-2 or AVCHD.

  Next: I create a new test project dummy with a film DV, import, apply effects and rendering. No problem. Export also works very well.

  The same project, create sequence HDV and import the small clip of HDV video. Plays very well. However, cannot make no effect and cannot export. (Same problem as before: hangs.)

  HERE IS WHERE I AM NOW:

  PP works fine in every way except that I can't make any effect of HDV footage and I can't export HDV to MPEG-2 or AVCHD format. I can make and export DV SD to SD (AVI etc) formats with no problems. I was also able to export the HDV SD AVI film (but only without effects - if I tried to apply effects in PP, they wouldn't render-hang as before).

  Here's what I see:

  ImporterProcessServer.exe hangs in the background (Task Manager) as PPProHeadless and processcoordinator. None of them shows no activity of the CPU. Somehow, the HD processing pipeline is defective (locked). There seems to be no problem for SD DV rendering.

  Here's what I did to try to solve this problem:

  -Downloaded and updated to latest version of DirectX (9 c for XP)

  -Downloaded and updated for more recent QuickTime

  -Ran CHKDSK on the system and A / V drives (no problem found)

  -Reinstalled PP, AE, SOUL and modules involved in the original game from DVD - ROM

  -Downloaded all updates of PP, AE, Adobe's SOUL and installed

  -Deleted all files of the user for the PP, SOUL, etc. (i.e. under Documents and Settings) and permit software to re - create.

  -Delete the Cache of media and permit PP to recreate (which she did successfully). Also moved Cache of media to a few different readers.

  -Double amount of virtual memory available (it was a shot in the water because everything had worked perfectly before)

  -Rebuild the cache plugin (now SHIFT key)

  -Checked for own log events (in the Windows Event Viewer)

  -Check the logs of other SOUL and PP without finding something interesting

  -Checked the nVidia card has latest drivers (it did)

  -Services checked to make sure minimum of background tasks are running

  -Checked to make sure that the disks have enough free space

  -Sacrifice a goat to the God of the Moon at midnight

  (Kidding on the last one of them, but just barely.)

  I'm open to suggestions, but I'll be skeptical of suggestions that the equipment or system is at fault, given that PP has run so well before, and given that the computer does not show any other problems. My hunch is that in some way something damaged the MainConcept HD codecs, but I guess that uninstall and re-install the software Adobe must have re-installed them, and which did not help. I don't know of another way to test them, or to re - install just this component. It is confusing that the SD treatment works very well.

  I'm frankly at a loss and have spent 8 + hours trying to understand this...

  Thanks for help that someone can give!

  Jim

  System details:

  Dell PW690/2 processors/2.66 GHz Xeon Dual-Cores

  Windows XP SP3 to date with all patches of OS

  4 GB OF RAM

  4 10K SATA drives inside the chassis

  1 drive eSATA RAID 0 array 1.5 TB external dedicated to A / V files (around 50% free)

  nVidia Quadro FX 3500 dual monitor display w/two NEC 1770VX

  M-Audio Delta AP 192

  Pioneer Blu - ray and regular DVD players.

  Video information:

  Mainly of JVC HD200 and Canon XH - A1 HDV 1080i. Some imported from FireStore, some captured via IEEE.

  Also a few former SD a Canon GL-2 DV film.

  The procedure is:

  1. Disable
  2. Uninstall
  3. Run the cleanup script
  4. reset
  5. Run the cleanup script
  6. reset
  7. Reinstall
  8. Activate

• IPCC Express, option for the appellants out of the queue and leave a message.

  We are running 4.0 (5) IPCC Express improved. I need to configure our current ICD script so that when the appellants are held in the queue, they can press 0, out of the queue and leave a voice message. The ICD script we use is an exact copy of the script icd.aef by default on the system, it has just been copied and renamed. My question is, what are the steps I need to use the script to enable this feature?

  Two options. Option 1: Use the IPCC completely to save messages and manage messages as you seem to did so. Option 2: Transfer the caller to your voicemail number pilot and use your voice mail system to record the message.

  Steps to Option 1:

  1 early on in the script, use the step to read the Contact information call to capture the called number and save it as a variable.

  2. use the step to get a string to allow the caller to press 0 to leave a message. On the Filter tab, allow only the key 0 be hurry.

  3. in the leg successful step to get a string of digits, add the following steps.

  a. contact Dequeue step.

  b. reading quick step that contains a prompt that asks the caller to record a message after the tone.

  c. step recording, which records the message saved in a Variable of type "Invite".

  d. use the Terminate step to end communication with the appellant (you can add a quick step before that game if you want to tell the caller that the message has been saved).

  e. at this point, you can either use writing document step to record voice messages in a folder on the server of the IPCC, or you can use a series of other steps to place a call to the queue and play the message the following agent that meets, or you can attach it to an email and send it it make the address email of your choice (or a combination).

  I have this HUGE warning. I had several problems with what I've been able to overcome, but it requires a bit of diligence.

  -L' registration step requires a termination character (# or *). If the caller hangs just straight up, the script returns an exception and drop dead. You can manage the 'contactinactiveexception' using a step on the Exception and have it go to a label that you can put it as the first step under the leg successful registration step. In this way, if the user hangs up, the script handles the exception by going directly to the successful step. You can clear the exception just after that.

  -You will also want to handle this exception before Terminate step. If the caller hangs up and you try to put an end to this contact when he is no longer active, the script will always die, and the remaining steps will not run.

  We use the option to place a call in the queue. In itself, this requires a lot of thinking to make sure that the script is not die when an exception occurs. I ended up putting some exceptions in place where if there is a problem and that the recorded message never makes it to an agent, a log file is stored on the server as well as messages stored in a .wav file. Then, an email is sent to the contractor with these attachments also.

  Thus, it is as effective as make you it. Try to keep things simple at first, and then build on that to improve the experience of the appellants.

  Steps for Option 2:

  1. use the step to get a string to allow the caller to press 0 to leave a message. On the Filter tab, allow only the key 0 be hurry.

  2. in the leg successful step to get a string of digits, add the following steps.

  a. contact Dequeue step.

  b. call no redirection to the number voicemail pilot.

  I have not used this option, so I can't say with certainty how Callmanager will handle this call. The voicemail system will need to see the call as transmitted from a number that has a voice mail on the system account. If this does not work, you can use a dummy CTI Port with a fake extension that is configured to transfer to voicemail, then the voicemail box must be associated with the wrong extension. If you use Cisco Unity, you will also be able to use a routing rule to force the IPCC calls to a particular mailbox. Call the Viewer from the unity tools depot allows you to see the way in which the appeal is made to the unit.

  I hope that helps you and that it is not too verbose.

• Cannot capture HDV in Windows 7

  I have a new Windows 7 PC (Dell Studio XPS 9000) and have not been able to capture HDV from my Canon Vixia HV30 camcorder.  I could not capture DV no problem when I put the camcorder to downgrade the output using 'DV Lock.  I tried Movie Maker and several other programs with the same result.  Each program recognizes the HV30 correctly.  When I start the capture, the computer manages to control the camcorder and begins to play.  However, HD video capture, usually to create a 0 bit file.

  I tried using different software in compatibility mode of previous versions of Windows and have also tried to use the "legacy" Firewire driver version, but nothing seems to solve the problem.  I don't know exactly what the problem.  I've seen some reviews that mention another card Firewire is required.  I also noticed that the Canon HV30 Windows driver is a "generic A / audio-visual device" driver.  I wonder if there is something that Microsoft needs to get to a specific Canon for Win7 driver.

  For any help or suggestion would be great!

  Hello ej76,

  Thank you for visiting the Microsoft answers Site.

  You can check with the manufacturer of the device camera to a compatible Windows 7 device driver. In addition, you can also try to install the device driver Windows Vista camera in compatibility mode and check the issue.

  To do this, please see the link below:

  http://social.technet.Microsoft.com/forums/en/w7itprohardware/thread/80cae5ee-dc98-4A2F-8284-a1ab826059b7

  In addition, you can check out the link below, provided by the manufacturer of the device to display information about the transfer HDV on your PC by looking for HD transfer in the search box.

  http://www.USA.Canon.com/consumer/controller?Act=ModelInfoAct&tabact=SupportDetailTabAct&fcategoryid=269&ModelId=16206

  I hope this information is useful.

  Thank you

  Mary
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Hard drive crashed. Cannot activate the new installation of CS4

  I had photoshop gifted to me by a friend. I never had record, just a digital camera download and via the phone took care of activation. Here is the text of my e-mail used to [email protected]:

  Dear Kyle,

  Thanks for purchase and register your copy of Adobe® Photoshop® CS4. You now have a multitude of creative tools at your disposal. While taking advantage of the online resources, we also encourage you to select a free benefit. At Adobe, we want you to make the most of your software, it's our commitment to you.

  Note: You are not eligible for additional benefits once you choose your delivery. There is a limit of free advantage by registered product.

  You guessed it, now get more.

  How the hell reactivate my cs4? Telephone and chat is 100% worthless.

  Lost information - response #1 in https://forums.adobe.com/thread/2008767

• Economy of capture HDV in MP3 format

  Hello... I have no problem with DV with CS6 capture, but trying to capture HDV, when I press stop in the capture window, rather than appear immediately to give the name of the file, location etc., dialog box option instead just automatically recorded as an MP3 file on the location of the recorded disc... Needless to say I can't even import this file in my project PP. MP3 As mentioned, this does not happen with standard DV import. FWIW I'm captured HDV footage on a Mini DV cassette from my Sony V1 camcorder via a Firewire cable to my PC.

  Any suggestion or help will be greatly appreciated... Thank you very much in advance.

  Here, many of us use the free HDVSplit for HDV capture:

  HDVSplit 0.77 beta

  Don't be fooled by the designation of the beta.  It is a program of old, but reliable.

• Premiere Pro CS6 (6.0.5) Capture HDV crash Bug

  Where will be fixed the bug Capture HDV to 6.0.5?

  Just buy the Mac version and may not even start to use because of this bug.  Seems to have been a question for a while (9/2013).

  Found many discussions on CreativeCow and Adobe receommend even reinstall and back to 6.0.4.  User who tried and even returned to 6.0.2 and still has problems with the HDV capture.  They used a Canon, I use a Sony HVR - Z1U.

  Thank you

  The f

  Hi Slim7,

  You can remove the previous version and follow the instructions below to download Premiere Pro CS6.

  Hello

  Please follow the steps below

  1. go to www.adobe.com

  2. click on downloads (top)

  3. Select Adobe Photoshop elements 12, which will open Photoshop download page. (This page is just to open the download page so do not click download go to the next step)

  4 once the Photoshop Elements download page is open click on the the link below for Premiere Pro CS6 start downloading.

  For MAC:

  http://trials2.Adobe.com/AdobeProducts/PPRO/6/OSX10/PremierePro_6_LS7.dmg

  6. double click on only .dmgfile to install the product once the two files have finished to download to start the installation.

  Once the product is installed, go to the link below and updated for the desired update.

  Mac:

  http://www.Adobe.com/support/downloads/product.jsp?product=98&platform = Macintosh

  Kind regards

  Vinay

• Capture HDV in Pr CS 6 cassette

  I have a Windows 7 platform and works with a video camera XL1a Canon HDV, but cannot capture any material in first Pro CS6 via a fire wire connection.

  The camera installs successfully and I can run through the window first CS6 caputure (fast forward stop playing and so on), but there is no picture.

  When I run caparture the camera starts but I have not any video in the preview window and it does not take into account any material.

  Can someone help how to capture HDV tape hardware in the PC?

  With two cameras showing the same problem, the more likely culprits are the driver or cable FW settings.

• reconfigure the queues

  Hi all.
  
  I need to reconfigure the queues on our small group and would like some advice of experts.
  
  I would like users to be able to submit work with commands like:
  
  $ qsub-l h_rt = 500 myscript.sub
  
  and/or
  
  $ qsub-memory hard-l = 30GB myscript.sub
  
  so that the Planner can choose lineups and hosts within the configured queues limits and resources of the host.
  
  Whereas the time limit works very well, I don't know how to implement the required memory...
  I think I should set on a host also available memory and declare it as a consumable resource, but I don't know how to precede.
  
  My queues would be something like:
  -1h.q (wallclock time 1 hour)
  -1d.q (wallclock duration 1 day)
  -3d.q (wallclock time 3 days)
  -2w.q (wallclock time 2 weeks or maybe nolimit..)
  
  Queue configuration example:
  
  # qconf - sq 1h.q
  QName 1h.q
  @1hour.hg parameter Listehotes
  seq_no 0
  load_thresholds np_load_avg = 1.75
  suspend_thresholds NONE
  nsuspend 1
  suspend_interval 00:05:00
  priority 0
  min_cpu_interval 00:05:00
  processors not DEFINED
  BATCH, [node03.cluster = BATCH INTERACTIVE QTYPE],
  [node25.cluster = BATCH INTERACTIVE]
  ckpt_list NONE
  pe_list make mpi orte smp
  Run again FAKE
  slots 8, [node03.cluster = 2], [node25.cluster = 2]
  TMPDIR/tmp
  shell/bin/csh
  Prolog NONE
  epilogue NONE
  shell_start_mode posix_compliant
  starter_method NONE
  suspend_method NONE
  resume_method NONE
  terminate_method NONE
  notify 00: 00:60
  OWNER_LIST NONE
  user_lists testers2.us
  xuser_lists NONE
  subordinate_list NONE
  complex_values NONE
  NONE projects
  xprojects NONE
  calendar NONE
  default initial_state
  s_rt INFINITY
  h_rt 01:00
  s_cpu INFINITY
  h_cpu INFINITY
  s_fsize INFINITY
  h_fsize INFINITY
  s_data INFINITY
  h_data INFINITY
  s_stack INFINITY
  h_stack INFINITY
  s_core INFINITY
  h_core INFINITY
  s_rss INFINITY
  h_rss INFINITY
  virtual_free INFINITY
  h_vmem INFINITY
  
  
  # qconf - shgrp @1day.hg
  @1day.hg nom_du_groupe
  setting Listehotes node04.cluster node05.cluster node06.cluster node07.cluster.
  node11.cluster node12.cluster node16.cluster node20.cluster.
  node21.cluster node22.cluster node26.cluster node27.cluster.
  node28.cluster node29.cluster node30.cluster node31.cluster.
  node32.cluster
  
  All hint/advice will be welcome.
  
  Thank you and best regards.
  Robi

  rnunnari wrote:

  If it's good for you, your work in progress will be killed by the operating system, when it is more than 30 GB used then you can use the limit of resources h_vmem to the configuration of the queue.
  The h_vmem requires the amount of virtual memory used by all running jobs. If the limit exceed, overconsuming work is killed.
  The virtual_free is a soft limit and work will get a SIGXCPU signal that could be intercepted by the work.

  In the case above, apart from ensuring that jobs don't take no more memory unless indicated, the Scheduler would also choose a host with any memory required for this task?

  HM no you define this queue resource limits settings. for example. your host have a physical memory of 40GB and you want to keep some free memory, you can set the h_vmem to for example 30G resource_limit. Present 2 jobs, asking h_vmem = 30G will be scheduled to this host, but if the amount of memory usage of these two jobs reached the limit of 30G, a job will be killed.
  The jobs are always planned, because the h_vmem is not a consumable.

  >
  >

  To set up the EMS just to submit work to hosts that provide 30 GB, then you can install a complex variable and adding the complex_values to the configuration of the queue.

  xuser_lists NONE
  subordinate_list NONE
  complex_values = 30GB memory
  NONE projects
  xprojects NONE
  calendar NONE

  Each task that demand memory-l = 30GB will be scheduled in this queue.

  That's probably what I'm looking for... but:
  (1) all the nodes in each single queue may have a different amount of memory

  
  (2) the planner needs to know the amount of memory provided by each host
  memory of l - 3) = 30 GB should be considered eligible any host that has at least this amount of memory
  (4) that the memory must be a consumable resource so that if other tasks are running in a host, the Scheduler will examine the memory consumed by this job

  Any comments/advice/help very welcome.

  Thank you and best regards.
  Robi

  I think that in this case the complex variable preconfigured virtual_free might work for you.

  qsub-l virtual_free = 30G

  Presentation of jobs like this is just programmed to be host providing 30G of virtual memory, or also the mem_free, which shows just the physical memory.

  Best regards
  Marco