The SDS in T400s uses the SATA interface?

Similar Questions

• Can Satellite Pro L300-22N - I use a SATA hard drive?

  Hi all!

  My hard drive is broken. Now, I want to put a new one in it. I have a SATA hard drive, but I can put it in this laptop? Because the old one was an ATA (I guess)

  Thank you very much!

  Hello

  I can confirm the info given by Liam.
  The L300 supports the SATA interface and you use the SATA 2.5 HARD disk

• Passage of thanks VM SATA drives? (update: a bug in the user interface web host)

  I use ESXi 6.0 for private home use and am currently building a NAS with him (on top of ESXi OpenMediaVault). However, as I am using only material quality consumer, my SATA controller does normally not for raw device mapping. I added the raw device manually in accordance with VMware KB: Raw Device Mapping for the local storage but when I try to join the top device (via the file on the local data store) a virtual machine, the user interface gives me an error message indicating that the capacity is too large for the given data store (of course, the system disk is much smaller than the data disks).

  Is there a way I can still add raw devices to virtual machines?

  Another update: upgrading the client to the web user interface host to 3731936 seems to fix this problem. I can now add virtual disks as RDMs in the web client.

• Any camera regardless of the interface is available for use with the LabView interface.

  Hello

  I intend to go for some CMOS camera,

  but I have a huge doubt before buying, the camera of menttioned above is not anywhere in this list. Nor can I see any type being supported USB device.

  The question is

  1. is a camera regardless of the interface is available for use with the LabView interface?
  2. Can I build a VI to communicate with any device image and recording of camera and take the data?

  Any kind of help or advice is greatly appreciated... I have to buy a CMOS camera and begin to run.

  Thank you...

  Hello Virginia,.

  I am pleased that this information has been useful, one thing I wanted to mention is that USB 3.0 has its own standard USB 3.0 Vision which is currently not supported. If this camera is also Direct Show compatible then you will be able to acquire an image using IMAQdx and manipulate all the attributes that are published to the API Live Show.

  I hope that USB 3.0 Vision will be supported in the near future, and we tentatively announced for this standard of communication for the August 2013 Vision Acquisition Softwareupdate.

  See you soon,.

  -Joel

• Can I use the SATA port connected to an optical drive to plug in a hard drive?

  I have a Pavilion e9270t desktop, Win7 Pro SP1, and I want to connect 3 HARD drive to the motherboard. Can I do this? Can I use the SATA port connected to an optical drive to plug in a hard drive?

  Thanks, CHemming

  CHemming,

  I've not seen UEIF support in the existing BIOS.

  If your demand on a 3T led, re - consider a maximum of 2 T.

  If you ask to have 3 hard disks, then you can do it without harassing the present cable of CD.

  The cage of your system hard disk will support 3 hard disks. Manual upgrade service

  All you need are the SATA data and power cables. Your Board has 4 SATA data ports.

  When you report back after inspecting your system for SATA power cables, I will move the cables and adapters, if necessary.

• Aironet 1240AG - cannot use the web interface

  I'm trying to set up a new Aironet 1240AG. After that she won an IP from the DHCP in my LAN, I can always connect using the web interface. I use an Internet Explorer 6.0 on Win 2000. It keeps telling me cannot find the server. Please I need help

  Hi Olivier,.

  First off you're welcome :) This method really works without the need for a WLC, be patient. Check the address static IP put you on your TFTP (* range 10.0.0.2 to 10.0.0.30)

  Rename the access point image file in the folder of the server TFTP c1200-k9w7 - tar.default for a series of 1200 access point

  Looks like a problem TFTP (no firewall on your PC?)

  Take a look at the details in the following threads that each has to do with TFTP. There are some great tips to troubleshoot TFTP some of my NetPros favorite ScottMac, Cisco's Stephen and Jack Young. The likely culprit may be you need to uncheck "Hide extensions for known file types" on your server TFTP;

  http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=WLAN%20Radio%20Standards&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc042b/8#selected_message

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc03c4/2#selected_message

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddbf271

  I hope this helps! Good luck!

  Rob

  Remember messages useful rate...

• ThinkPad E420 - what is the type of this laptop SATA interface? Is this 2 SATA or SATA 3?

  Dear all,

  What is the type of interface SATA of ThinkPad E420? Is this 3 SATA or SATA 2?

  I noticed that this laptop hard drive transfer rate is 3 Gb/s, which means that it is a SATA 2 HARD drive, isn't it? It also means that the laptop SATA interface is SATA 2?

  I tried searching the support site and product from lenovo for this information, but I can't.

  Thanks in advance.

  Best regards

  Haris

  You're right, the E420 is SATA2.

  SATA3 is very rare in the laptops!

• ASA 5510 using only the GB interfaces

  I am looking for should I use a 5510 to activate two interfaces for VPN connections broadband from only a few sites. Our 5505 s (I have dozens) can not manage speeds of more than 100 MB and I have now a few FIOS beyond that--150 to 300mpbs.  I want a 5510 basis who needs to manage a few voice / data sites and just use two interfaces. A basic 5510 allow 2 gigabytes or just ports FE interfaces?  I have to be able to use 2 GB interfaces and no one else. I don't know that the 5510 will probably support the same QOS settings that I use on the 5505 s... I just need more speed interface so that I'm not bottlenecking data (I know I could use several 5505 s and extend the charges but is not how I want to do it for other reasons). Thank you

  Hello

  To my knowledge the ASA5510 supports 2 x 1 Gbps interfaces when you the Security license for the SAA. The basic license counts 100Mbps interfaces.

  Take a look at this document for more information on licensing above

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/license/license82.html#wp190732

  Its a document from the 8.2 version but its still even to 9.x on the license requirement more security get the 2 x 1 Gbps interfaces

  The documentation for ASA5500 series promises an 300Mbps for the ASA5510 model flow, but I guess that's a value of location. In the most recent document, two values of max flow max and Multiprotocol are given.

  Here's a link to the document

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6032/ps6094/ps6120/prod_brochure0900aecd80285492.PDF

  -Jouni

• Use the Gigabit Interface as an interface of Interior with guarantee of 100

  I have a PIX 525 with two Gigabit interfaces, and I'm doing an internal interface with 100 security, 'nameif ethernet0 gb inside the security100' is the command that should work. I get this message:

  Aspirin (config) # nameif ethernet0 gb inside the security100

  Security 100 is reserved for the "inside" interface

  Use: nameif

  No nameif

  Aspirin (config) #.

  What is the problem? Is this possible? How are you?

  Please try to use the lowercase I name when the interface so that it should read inside.

  It is case sensitive

  Thank you

  Syed

• Public and private IPs on the same Interface by using NAT Exemption/policy NAT

  I'm looking for some feedback on whether my thoughts on the installation program will run.

  Equipment: PIX 515E 6.2 (2)

  Scenario:

  The inside interface of the PIX will host 3 blocks of addresses IP - 24 public 2 blocks and 1 private/16 block. (All IP addresses have been replaced by dummy blocks.)

  Blocks of audiences:

  * 192.168.10.0/24

  * 192.168.20.0/24

  Block of private:

  * 10.50.0.0/16

  Traffic from the public 2/24 blocks should go through the firewall without address translation.

  The two blocs of the public will be able to receive connections initiated from the Internet.

  Public blocks will need to be able to send and receive traffic on a static VPN tunnel to our headquarters without subject to address translation

  Traffic leaving the sector private/16 block should be subjected to PAT before passing through the firewall.

  Private/block 16 will not receive incoming traffic from the Internet (other than responses to outbound connections initiated from within the private block).

  However, the private block will also have to be able to send and receive traffic on a static VPN tunnel to our headquarters * without * subject to address translation (i.e. hosts on our corporate network must be able to initiate connections to the private block and vice versa).

  The inside interface of the PIX will be connected to a Catalyst 3xxx series layer 3 switch, which will be responsible for routing all internal (so the PIX will never be routing of traffic on the interface, it was received).

  My ideas on how to implement are:

  * Use the exemption of NAT to exempt public address translation blocks. This will allow incoming and outgoing connections through the firewall.

  * Use the exemption of NAT to exempt the block private NAT when connecting to our head office on the VPN tunnel.

  * Use policy NAT w / PAT to translate the block private connecting to all other hosts.

  I have translated these thoughts in the following configuration snippet.

  Because the NAT exemption is processed before policy NAT in the evaluation of the NAT rules, I believe that this should allow the public IP blocks treat incoming/outgoing traffic without translation, while submitting the private translation block (except during handling of incoming/outgoing connections to our network of corporate office).

  Can someone confirm my assumptions about this?

  # ----------------------------------------------------------------------

  traffic of # which should be exempted from translation

  permit ip 192.168.10.0 access list nat_exempt 255.255.255.0 any

  nat_exempt 192.168.20.0 ip access list allow 255.255.255.0 any

  nat_exempt ip 10.50.0.0 access list allow 255.255.0.0 10.100.0.0/16

  traffic of # which should be the subject of translation

  policy_nat ip 10.50.0.0 access list allow 255.255.0.0 any

  # Suppose 192.168.5.1 is the address to use for PAT

  Global (outside) 1 192.168.5.1

  NAT (inside) 0-list of access nat_exempt

  NAT (inside) 1 access-list policy_nat

  # assumes that 192.168.10.7 is the IP address of the inside layer 3 switch

  Route inside 192.168.10.0 255.255.255.0 192.168.10.7 1

  Route inside 192.168.20.0 255.255.255.0 192.168.10.7 1

  Route inside 10.50.0.0 255.255.0.0 192.168.10.7 1

  #assume the following configuration sections appear elsewhere: static tunnel VPN, ACL, ifconfig, etc..

  # ----------------------------------------------------------------------

  Yes, this will work, even if you don't need political NAT for the 10.50.0.0 network. For PAT the 10.50.0.0 network when to anywhere (except via VPN) just do:

  Global 1 192.168.15.1 (outside)

  NAT (inside) 1 10.50.0.0 255.255.0.0

  As I said, you have works perfectly, the above is just an easier way to do it.

• How to configure VPN remote access to use a specific Interface and the road

  I add a second external connection to an existing system on a 5510 ASA ASA V8.2 with 6.4 AMPS

  I added the new WAN using another interface (newwan).

  The intention is to bring more internet traffic on the new road/interface (newwan), but keep our existing VPN using the old interface (outside).

  I used the ASDM GUI to make changes and most of it works.

  That is to say. The default route goes via (newwan)

  Coming out of a VPN using a site to character the way previous (out) as they now have static routes to achieve this.

  The only problem is that remote incomming VPN access Anyconnect do not work.

  I put the default static route to use the new interface (newwan) and the default tunnel road be (outside), but that's the point is will not...

  I can either ping external IP address from an external location.

  It seems that the external interface doesn't send traffic to the - external interface (or at least that's where I think the problem lies). How can I force responses to remote VPN entering IPS unknown traffic to go back on the external interface?

  The only change I have to do to make it work again on the external interface is to make the default static route to use external interface. Calling all internet traffic to the (external connection) original

  Pointers appreciated.

  William

  William,

  As it is right now that you will not use the same interface you have road to terminate remote access unless you know their IP addresses by default.

  In one of the designs that I saw that we did something like that.

  (ISP cloud) - edge router - ASA.

  The edge router, you can make PAT within the interface for incoming traffic on port udp/500 and UDP/4500 (you may need to add exceptions to your L2L static) of the router. It's dirty, I would not say, it is recommended, but apparently it worked.

  On routers, this kind of situation is easily solved using VRF-lite with crypto.

  M.

• How to use the Shell of the user interface with multiple applications (ear)

  I use 11.1.1.6 JDeveloper.

  I want to modularize the functionality in applications (ears) and use the Shell of the user interface as a navigation mechanism between applications and single entry.

  Is this good?

  What is the use of Shell of the user interface best practices.

  What about security (2 AA)? Security of the ADF?

  Thank you

  Hi user,

  You can use the shared library ADF function if you would like more information

  http://andrejusb.blogspot.AE/2010/07/deploying-ADF-applications-as-shared.html

  use the adf security

• Anyone who has a problem with the system crashes when importing using the new interface to import

  Anyone who has a problem with the system crashes when importing using the new interface to import

  Can specify you what Adobe program you use so that we do that your post is in the right forum?

• In Camera Raw 8.4.1 I can open the DNG for 3 years, but it's using the old interface and features not the current - how can I change this. Rebuilt the cache.

  Creative cloud running on a HP with 18 GB of Ram - I'm working on a project using DNG 3 years old and when I open in my current Camera Raw, it uses the old interface with 'contrast' down and "valorisation" below 'exposure' - How do Camera Raw to open with the current interface?

  Thanks for any help.

  Craig

  If you are referring to the version of process , you who set the ACR camera Calibration tab.

  

  Also remember that all images with previous settings will show the process used when they were stopped.  Which can also be changed in this tab.

• What should I use to create the user interface of a CEAP plugin on mac

  Hey there,

  I'm new to the development of a plugin, but I did development of script for quite a long time however. I'm tring to develop an ECAP plugin. I go to the sample project of "Panelator" (from AE CC SDK), but I don't know how to create ui for the control panel plugin stuff.

  The sample project is not an example of code to do this on a mac computer, I found the code examle for windows however.

  So, can someone generously tell me how? I had to do with cocoa? But as I understand it, I can only use Objective-C to write cocoa ui.

  Thank you very much!!!

  Hi Li Zhiqing,

  We have just announced in the next major update to AE CC signs HTML5 is supported:

  http://blogs.Adobe.com/AfterEffects/2014/04/new-changed-after-effects-CC-2014.html

  This will allow to create the user interface using HTML5 and use your scripts for the conduct of AE.  It is quite a bit easier than the use of cocoa for the construction of the UI panel.  Thoughts?