The volume max Sound Check turned

Similar Questions

• Siri remote control controls the volume but will not turn on or turn off the tv more

  LLA Siri remote control the TV volume, but does not turn the TV on or off more. My anynet + him Cec is enabled. How can I get this function runs again. Tired of using two remotes

  That is dependent on the TV then you will need to contact their support

• Audio Line in/out on SP2309W lowers the volume of sound transmission

  Try to use plugs SP2309W Audio Line-in/out to pass the computer sound through headphones, I found that the volume is * much * reduced, compared to plugging headphones directly into Win8 x 64 PC.

  As discussed in http://en.community.dell.com/support-forums/peripherals/f/3529/p/19328102/19680277.aspx, this plan offers no functional benefits; It's just more convenient in terms of layout of the cables on the desktop.

  Does anyone know if this behaviour (interfering with sound signal and by reducing its volume) is design? Is it possible to assign it?

  "Interestingly, when the monitor enters the power saving Mode, the sound is not through audio in/out more."
  This is normal on all Dell monitors.

  The other problem has been reported before, but the sample size was small. I've not heard of a fix for this. I would plug the headphones directly into the PC.

• Narrator has no sounds. All the troubleshooting for sound check.

  Narrator does not. Sound clip very well on another app

  Hello

  1 did you do changes on the computer before the show?

  2. do you receive any error messages?

  3 - is the issue limited to only a particular type of file such as Microsoft Word or happen with any kind of file?

  I suggest you to visit:

  Troubleshoot Narrator

  http://Windows.Microsoft.com/en-us/Windows-Vista/Troubleshoot-Narrator-problems

• Apple tv 4 can I cut or reduce the volume of the sound effects o

  using the Apple TV 4 a trip through applications, I find very annoying sound effects. Is it possible to turn off or reduce the volume?

  You cannot change the volume, but you can turn off: settings-->--> clicks of navigation audio video > off

• How can I turn back on the volume on a Windows XP computer?

  Using a Windows XP computer, I sailed somewhere that had the ability to mute sounds. It is not the volume control, I checked to make sure that no sound is cut off or too low. I also tried to plug in my headphones to the other jacks, and I can still hear nothing.

  Unfortunately, nothing has worked, and the volume remains silent. I don't know how to get back to everything I clicked, too.

  Any suggestions are appreciated.

  Using a Windows XP computer, I sailed somewhere that had the ability to mute sounds. It is not the volume control, I checked to make sure that no sound is cut off or too low. I also tried to plug in my headphones to the other jacks, and I can still hear nothing.

  Unfortunately, nothing has worked, and the volume remains silent. I don't know how to get back to everything I clicked, too.

  Any suggestions are appreciated.

  =====================================
  The following links may be worth a visit:

  No sound in Windows
  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows
  (Win XP / Vista / 7)

  (307918) how to troubleshoot sound problems in Windows XP
  http://support.Microsoft.com/kb/307918/en-GB

• Turn off the vibration and sound for notifications?

  Sound & Notification in a sliders to media parameters, alarm and ring volume, but no notifications. There is a switch to vibration for the call, but not turn it off for the vibrations.

  How do I turn down the volume on notifications and turn off vibrate?

  It is not related to Sony, it's Google work. But there were other threads on how to disable or enable the vibration to other than the default applications:

  https://talk.sonymobile.com/T5/Xperia-Z1-compact/issue-with-vibration-and-notification-per-app-since...

  You need to customize each app.

• the volume control of the sound both play at the same time

  Hello...

  I want to separately control the volume of sounds

  I used a VI of its volume, but it reduces the volume of these two sounds,

  even if the ID of the task of both played sounds are provided separately.

  Please help me for the same...

  Thank you.

  If I'm not wrong, its volume will set the system volume. So, it does not depend on "audio files". I think so...

• Can not adjust the volume of the music unless the piece is played

  Hey people,

  I noticed that when you use Spotify and Pandora, by pressing the volume buttons on iPhone adjusts system volume if a song does not play. Once a song begins to play the volume buttons to adjust the volume of the music. If the volume came to be turned up really loud the last time that the application has been used, you start to play the song at full volume to lower. Any ideas if this can be fixed? It would be nice if the volume buttons would change the volume of the music whenever you are in the application at all, not once a song begins to play.

  Thank you

  Owen

  Hi osmithy,

  Thank you for using communities Support from Apple!

  I understand that when you do not listen to music, and you set the volume on your iPhone, it adjusts the volume of the system as you say, but when music plays, the volume buttons to adjust volume of the song.

  This is the expected behavior and works as expected. This information can be found in the following link.

  When you are on the phone or listening to songs, movies or other media, the buttons on the side of the iPhone set the audio volume. Otherwise, the buttons control the volume of the ringer, alerts and other sound effects.

  Volume controls - iPhone

  Best!

• Re: Satellite A200 volume "increases" if I turn left or right meter

  Hi guys,.

  I have a Satellite A200-1ah.
  The problem is with my volume wheel. The volume "increases" if I turn the meter to the right or to the right.

  Help, please.

  Very strange
  It seemed to start?

  If this isn't the case then this problem could be related to hardware and so you would not be able to fix it.

  By the way; Do you use the OS preinstalled Toshiba or did you change something?

• Disk Defragmenter has detected that Chkdsk is scheduled to run on the Volume: C:. Please run Chkdsk /f.

  I know this question has been asked several times, but I did these steps and still not get Defragmenter to work.  My Disk Doctor said I don't have problems with my Defragler work program - but I don't have a C: drive not 'dirty '.  I have Windows XP Home Edition and do not know how to run an XP Recovery Console.  Y at - it an easy way just to get the Defragmenter to work?... when I run Chkdsk... It goes through stages and then closes and the problem is still there.  Defragmenter just stopped working, my computer everything works fine.  Help, please.

  Hmmm...  It should only take a few minutes for ImgBurn to create the bootable XP Recovery Console CD, then maybe one of the songs that you have downloaded (xp_rec_con.iso or install IgmBurn) won't quite right.

  You want ImgBurn to play a happy tune when it is successful and a "Oh no!" message when it fails, but it shouldn't take hours to burn this ISO file bit.  You can try another system.  You can always uninstall ImgBurn when finished.

  I say 'be patient' when you run the chkdsk /r command because sometimes it seems to be stuck (or even go back), but it should end later.  Depending on the volume size, the amount of data on the volume, the speed of your system and what the chkdsk finds to do, you can watch several hours.

  Look at these words from the mouth of Microsoft:

  If you use chkdsk /f on a drive or drives for very large (for example, 70 gigabytes) with a very large number of files (for example, millions of files), chkdsk may take a long time (for example, over several days) to complete. The computer is not available during this time because chkdsk does not relinquish control until it is completed.

  At the time of this writing, I'm guessing a disc 70 GB was "very large" but it is quite modest by today's standards.

  Now with today's technology, it is unlikely to take days, but it could still take some time!  If your HARD drive is afflicted with a problem material and dying, it can never finish or be unable to fix things.

  To start XP, it automatically checks each volume to see if it is dirty and will try to run chkdsk from the afflicted volumes.  Sometimes, it's good enough to clear the dirty bit, sometimes it isn't.  You will see a message at startup if the volume should be checked for consistency and XP will do the best.

  That's exactly what the message tells you:

  Disk Defragmenter has detected that Chkdsk is scheduled to run on the volume: (c :))

  You can query the dirty bit on a volume from the command prompt window.

  Click Start, run and enter in the box:

  cmd

  Click OK to open the command prompt window.

  To query the bit of impurity on drive C, type:

  fsutil dirty query C:

  The sample output:
  Volume c is dirty
  Volume C: is dirty

  Type "exit" to close the command prompt window.

  If you are suspicious of your HARD drive and think it might be failing, now would be a good time to backup your personal data (documents, pictures, music, etc.) to an external location - a separate attached USB drive or a few clouds on the Internet.

• What is this average, Disk Defragmenter has detected that chkdsk command is schduled to run on the volume: (C). Please run chkdsk /f.

  Been trying to run the defrag on my C drive and this message keeps coming up.

  When you try to defragment a volume of that Disk Defragmenter reports:

  Disk Defragmenter has detected that Chkdsk is scheduled to run on the volume: (c :))
   
  Please run Chkdsk /f.

  This means that the volume that you want to defragment was marked 'dirty' XP.  This is not necessarily all of the data has been lost on the volume, it simply means that XP thinks that the volume should be checked to find errors because of something that happened before.

  You won't be able to defragment the volume until the dirty bit has been removed.

  A volume can be marked as dirty, if the system underwent a power interruption (power failure, pulling plug, removing the battery, button / stop), abandoned restart or an abnormal termination.  One of these events?

  When XP starts, it automatically checks the bit of impurity on each volume.  You can also tell XP to ignore the bit of impurity on any volume, but this probably isn't a good idea in case there is a real problem that needs to be fixed.  If you have a hard drive where the dirty bit will not disappear, you can tell XP not to check.

  If the starting XP detects that the volume is dirty, it will be automatically run the check disk with error correction (chkdsk/r) and try to fix the problems detected.

  If the chkdsk command succeeds, it clears the dirty bit, and then you can defragment the volume.

  You can check the status of your bit of impurity from a command prompt window.

  To do this, click Start, run and enter in the box:

  cmd

  Click OK to open a command prompt window.

  For example, to query the bit of impurity on drive C, type:

  fsutil dirty query C:

  The sample output:
  Volume c is dirty
  Volume C: is dirty

  Is the volume of your sale or it is not dirty?

  Since XP of course already thinking that the volume is dirty, XP will automatically run chkdsk when it restarts to try to clear the dirty bit, in order to plan another running chkdsk can not help you much.  Sometimes the auto chkdsk on a reboot will be not only clear things to the top, but you can try it.

  I would like to start in the XP Recovery Console and run chkdsk /r from there you can actually watch and see what happens and decide what to do about this.  When own running chkdsk/r, it clears the dirty bit unless your HARD drive is somewhat distressed.

• Sound seems to be decreasing after that I have used headphones, or turned down the volume.

  I have a HP G62 and he had a GOOD volume, but after that I have to use headphones or turn down the volume, he seems to do something for the volume and when I want to play sound after headphones are disabled you can hardly hear it.
  I turned the volume up on top of everything I can find, but it is so weak, it is not worth listening to!

  Hello

  1. What is the operating system installed on the computer?

  2. were there any changes (hardware or software) to the computer before the show?

  Perform the steps in the article, and check whether the problem is resolved or not.

  No sound in Windows (Windows 7)

  Note: this also applies to Windows Vista and Windows XP

  Hope that helps.

• My reading shows the HDMI as a default device, but the sound is yet to come of the computer laptop, even when the volume is turned off on it

  Original title: HDMI sound

  I know that many have had problems, but I did not mine specifically. My HDMI connection was working fine with my laptop HP and m HD tv. I didn't use it for a while, now it is just the video, no audio on the TV. My reading shows the HDMI as a default device, but the sound is yet to come of the computer laptop, even when the volume is turned off on it. Ive read all the reviews and updates of pilot who was old. I don't know what else to do!

  Hello

  System Restore does not have this long period of time.

  You may want to refer to the suggestions in the thread below link and check.

  No sound via HDMI output portable computer connecting to TV

  I hope this helps.

• Windows XP my sound recorder audio device is a DODEC Audio USB, the volume and advanced is grayed, how do he turned the back?

  I just installed a turntable to record albums. I installed everything simply by following the instructions. The volume of the sounds and advanced recorder is grey and everything I do doesn't change it. Can someone help me?

  Hello

  You can view these methods:
  Method 1

  Download & install the previous version of the drivers for the sound card and check if it solves this problem.

  1. type devmgmt.msc in the search box start and press ENTER.

  2. in Device Manager, expand the audio drivers listed in the list of devices.

  3. right click on the audio driver > click Surdesinstaller.

  4 restart the computer and install the downloaded software.

  Method 2
  
  In addition, if you use a recording program, update or reinstall the program registration.

  Method 3:

  Please follow these steps to enable the "Windows Audio" service:

  1. Open the control panel of Windows XP by (depends on your settings in Windows):
     By clicking on "start > settings > Control Panel.
     By clicking on "start > Control Panel.
  2. Open the "Administrative Tools" Panel by (depends on your settings in Windows):
     Double-click the control panel 'administrative tools '.
     Click on "Performance and Maintenance" and then "Administrative Tools".
  3. Go to 'Services' Control Panel by double-clicking it.
  4. Locate the "Windows Audio" service.
  5. Check the "Status" column to see if it is disabled.
  6. If it is disabled, click with the right button on the "Windows Audio" service and choose "Properties".
  7. On the general tab, change it "Startup Type:" drop-down on "manual".
  8. Restart your computer.
  9. Follow steps 1-6 to open the properties of the Audio service 'Windows'.
  10. Click on the 'Start' button to activate the Audio service 'Windows'.
  11. You will now be able to change the control panel 'sounds and Audio devices '.