There is no diagram

Similar Questions

• EXPORT hi res diagrams since InDesign cc

  I create an InDesign document to PDF export for the web. There are many diagrams that I understand that I made in Illustrator and exported to PNG (also tried TIFF, but no difference). When I put in my InDesign document, they look quite good HOWEVER when I export to PDF diagrams are coming Blur/Blur (especially text in diagrams). Please is it someone could share their experience with how to get diagrams come out looking beautiful and strong and crisp in a PDF file for the web. I'm pretty new to this, so any help would be greatly appreciated. I see my deadline creeping up on me!

  Thank youI

  Go to Illustrator, save your file under HAVE and place them in InDesign.

• Point cloud with missing data and 3 sets of data

  Hello

  I'm doing a scatter diagram that has 3 sets of data in it (i.e. 3 plots on the same graph), except that 2 of my sets of data have a missing value while my third set has all the values. I end up getting 2 lines that are disconnected. I can't just remove the line containing the missing data for the 2 sets of data because since my category axis is time, my data points get shifted and no longer appear at the right time. This is the chart that I have.

  

  Thank you.

  Hi Gabrielle,.

  If there is a diagram of dispersion, the x axis is a value axis. If you have auto selected for the min and max values on this axis, the scale may change when you remove the data point, 15, 85, but the rest remains in the same position relative to the values on each axis of ordinates. What change will be , however, is the curve on which 15 85 approached a local y maximum.

  Scatterplots will always leave a gap in the line/curve of connection where there are a pair of missing data. There are two ways to close the gap.

  If the chart is an essentially linear relationship, you can use a calculated value is pair up with the lack of value x. The downside of this is that the representation of this point will be indistinguishable on the map of the other data points, measured.

  A better way would be to make two tables, one with the full data set, the other with the partial sets, but with the pair missing completely removed.

  Adjust the cards the same size and have the same scales on each axis, then just remove one of the cards except the data points, the curves connecting the data points, the x axis of ordinates and the legend showing the color and the forms used to plot each series.

  Give a graphic a transparent filling and place it in front of the other.

  Kind regards

  Barry

• Toshiba power saver is unbootable

  (Satellite M40x)

  Hi all

  I need help, such as every time that I am pressing energy saver Toshiba told me that I have to open windows power options and use the Toshiba power saver, but I can find it there in the diagrams. I have chenged the parameters once accidentally a normal windows and settings for the Toshiba power saver no longer works.

  I tried to re - install (download formtoshiba site), but now I get an error when starting...

  Please help because I lack the characteristics

  Sander

  You must go to the window power options and change the POWER SCHEMES drop-down back to ECONOMY of ENERGY TOSHIBA. Except if it is positioned like this energy saving windows will always be the default.

• Satellite M100 - where is a 2nd RAM slot?

  Hello

  I read in the manual there are two ram slots in this model, but can not see elsewhere.
  If anyone can tell me where is the other location, there is no diagram?

  Advanced use of the Forum to search always ;)
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=40422

  * A slot under the keyboard and the other bottom of base *.

• My h9 - 1215t Phoenix HPE is missing in the form of graphics card.

  Hi all. I recently bought a desktop Windows 7 model HPE h9 - 1215t Phoenix from the HP store. The day before I placed the order, the computer was available with the Nvidia GTX 680 as an option, but deleted the day I bought the computer, so I ordered the computer and bought an EVGA GTX 680 instead (Yes, cost me about $300 + extra too). Well, today, a week or two after you received the computer, I had the chance to open and take a look at the plug on the side of the PSU to be sure that I am able to run a 680 GTX in there, because it requires at least a 550w power supply at least 38A the 12v rails. I knew I was good on the 550W as it comes with a 600w PSU, but I wanted to check the amperage of rail. So I open the housing cover side and take a look at the PSU, and I see that I should be able to run the graphics card very well and a call to technical support available EVAG explaining what I confirmed it. But then I noticed something off the computer pedal. I noticed that there seemed to be different from what I saw in the manual, on the HP support site and tear down/install videos. Then I realized, IT LACK THE CONSERVANT SUPPORT of CARD GRAPH. This support is essentially a medium which has two functions, first of all, it supports graphics cards that are installed in these computers, as they can be big and frame h9 more small/more low need help a little. In addition, it supports and adds stiffness to the chassis/body itself. Well, I looked on the housing cover and of course, there is a diagram showing the missing piece, and how you should remove it to work on the computer. I was on the phone all NIGHT HP, fired back from technical support and sales and tech and sales and so on and so forth. After-sales service was good and they seemed like they really wanted to help but could not, support seemed like they did not give two * s, is if you could even understand them well enough to revisit their behavior. After having recited my S/N and the model number, name and address and million times I gave up. Supervisors do not help yet. Sales gave me an option indicating that they would send me a new one, but, that I had to pay for the new and the accusation that is held on my card until they received a new once I removed the stand and put it on mine or just returned my old one. This was not an option that I don't have an extra $ 1,000 on my line of credit, as well as, given the fact that I WOULDN'T have to DO. It's HP high time f *, now why in the heck do I have to buy another computer, so they will fix the problem?

  http://support.HP.com/us-en/document/c03028387

  The support is shown in this tutorial from HP that precedes, it appears in "Step 2" and "Step 3"in the tutorial."

  Now my question is, one, someone already had this problem before? Because it really seems to be as if the person build this forgotten CTO computer reinstall the support when he'she finished the job and he bundled. Also, my other question is, WHO in the heck do I talk to to get this replacement part. Because that of course standard HP support is room runable, or not of the all ready to help me with the problem. Anything short of this computer back or get a replacement can be done? Is not an option that I use this computer for work, and I absolutely can't be without him for more than 1 day and I absolutely refuse to buy, or even let put them a cool/warm on my card for the additional amount for a new computer, because it's not my fault, and I would not solve the problem. HP needs to fix. I don't understand why someone can't just get a model h9, pop the * er open and put the dang game in the mail. When did things get so complicated and such to where people can't complete this simple action? Can anyone, anyone at all help me? Anyone from HP? I would really like to hear your opinion and your explanation as to why your emplyees completely refuse to help me. Seems as if HP now has my money, for this purpose, they don't give 2 of those stinking.

  @Win7Loyalist:

  I understand your frustration when something isn't quite right with your new test bench.  I've been there.  You paid a lot of money for a complete system, and you wait until it is complete.

  I also own an HPE Phoenix system, and I have a model h9 - 1120t with an i7 3770 k liquid and a GTX 670 which I added myself.  Mine is a Power Edition MSI GTX 670, which is Overclocked at the factory and is actually a bit better than a reference GTX 680 model.

  But I hope I can ease your frustration a bit, unless you have already found or bought one of the supports.  If so - you can skip reading any further.

  This metal bracket is not required to be left in the case, and it is designed for the purpose of shipment.  Yes, it supports and rigidity was added to the case, but this is necessary only when shipped, and not when its definition in your office or anywhere where you put your home.  The Phoenix case is not fragile and didn't need added support when in your office.

  I already had my GTX 670 graphic card when I got my rig to Phoenix, and I removed the clamp support immediately and have never used.  He has been since then in the area of HP in my attic.  I have have my system for over a year now and can you - you have no need (or want) that ugly support in there, unless you plan from somewhere, this shipping system.

  Because you must return your system to its original configuration if you need to send back to HP for warranty service, you must deliver 630 GT little in it anyway, and it's so light it will not need the support.  I suspect that's why they left.  Of course there's always someone just forgotten.

  In any case, I understand that you should have the support you are 100% right about this, it is not necessary, but I don't want mine here.  I spent a bit of time to clean the birds nest of wiring that HP did (it was a mess) and I really "tightened" and straightend the wiring inside my case and having decent airflow.  Much better than the factory.  This just square would stand in the air, not to mention that it's ugly.

  I'm surprised that its hard to get a good.  That makes no sense at all.  It's like a $5 coin.  I'd sell you mine, but I have a year left on my warranty and I need if I must refer the drill rig to HP for anything whatsoever.

  In any case, enjoy your Phoenix is really a very nice gaming platform.  I can launch ANY game of current generation such as BF3, Bioshock Infinite, Skyrim, Tomb Raider and even Crysis 3 - on the highest settings at 1920 x 1080 and get great frame rates.

  I said it before and I'll say it again, I really don't understand why HP has never promoted this platform.  It was obviously intended to go against Alienware, but no one has heard of the HPE Phoenix system.  HP does not appear to worry about marketing or promotion of this system at all.

  What a waste.

• Reading data with NOR-5772

  I'm reading the data with the NOR-5772.  I tried the example code(NI_5772-Getting_Started_(Host).vi), and it will read noise (with nothing plugged into channels).   However when I try to send a signal (such as that generated with a NEITHER-DAQ card on the same system and routed to AI0/AI1), the signal does not change a lot of the noise.   I have the drivers updated and am under LabView 2012 (32-bit and 64-bit, I get the same result)

  Everyone has to experience this problem?   Thank you.

  Yes, the device is AC coupled and has a high pass filter.  There is a diagram of frequency response on page 20 of the user manual:

  http://www.NI.com/PDF/manuals/373625a.PDF

  It seems that the cuttoff frequency is about 100 kHz.

• NEITHER Starter Robotics it

  Hello

  I am interested in this kit 'DANI'... really I intend to buy it to have on the sbRIO-9632 trained in real-time applications.

  My question is after having used this kit in with examples of labview training... I'll be able to use the sbRIO 9632 in another application also for motors continuous command.

  I would like to build a project of DC motor Position control

  using a mould to tilt mechanism and I think to get use of the sbRIO 9632 and the circuit of engine on this kit and use it to Pan tilt mechanism

  I have waiting for a tilting mechanism pan with two engines 12DC, this mechanism also has a pot. for your comments.

  I'll go and buy this robot kit and you train?

  Am I able to disammble (without losing its function as a robot when gathered) and use the tips (driver sbRIO9632 and motor circuits) need in my project of pan/tilt?

  Thanks in advance

  The sbRIO on the robot Starter Kit still usable by itself, even if it is removed from the robot.  You can use it as any other sbRIO-9632.  One thing to keep in mind is that you will need to provide a power supply for the Board once it is removed from the robot.  It requres a 19 to 30 VDC power supply.

  Regarding your question about to dismantle the robot, there is no reason that this will not work if if it is installed correctly.  Do not forget that you would be responsible if yes or no it works once reassembled, because NEITHER does not officially support dismantling the robot.  There is no diagrams or instructions (that I know of) to do this.

  Chris M

• Analysis of torsional vibration

  Hello

  I have the speed Vs time from one end of the tree with the other end of the tree. I want to do the analysis of the vibrations of twist in a tiara. Could someone help with the step by step procedure?

  In the results, I would need the angular displacement (°) vs speed axis in different orders. Also, there should be diagrams of campbell showing the critical frequency (who liked angular displacement in a particular order of vibration)

  Thank you

  Vishnu

  Hi Vishnu,

  Assuming that the speed data are correct phase for both ends of the tree, the difference will be momentary speed difference. You are actually looking for data 'movement' or twist, so start by integrating the two signals in the time domain. This should provide a signal increases gradually. Subtract one from the other, and you should be left with a straight line with momentary variations around zero. If it's not right around zero, then you will have a broken tree (different speeds) or digital issues due to long queues and limitations during the integration. Best option then is to assess more short sections of data as high-pass filtering of the original data or calculated may introduce errors.

  Assuming you start with speed in ° / s, the reading will be in degrees.

  Frequency spectra and order plots then must be made for which you can search for "joint time frequency and order analysis tool for DIAdem." Don't ask me about it, because I know that there are, but haven't found any easier options using our dynamic frequency analyzers.

  Amplitude control / speed score should normally show resonances, you can convert frequency again to show frequency.

  HTH,

  Marcel

• EliteBook 8540p: I have no driver or registration for memory card reader in Device Manager

  There is no registration for my memory card reader in Device Manager. The card reader does not work. SD card works in my other PC. Tried to download the Driver Ricoh Media Card Reader suggested by HP Support, with no results. It's as if there is no such thing as the card reader. Is there a way to shake the player in a localizable device? Or is it dead material?

  Hello:

  If there is that no device Base system not listed in Device Manager in need of drivers, then the unit is completely dead/disconnected from the motherboard.

  I'm not a PC repair in commerce or training technology, and there are no diagrams of the motherboard I know to see how the circuit card reader is attached to the Board of Directors.

  If you look at Chapter 4, pp 93-94's service manual, it seems that you can replace all separately.

• OR SHC68-68 for the PXI-6255

  I see that the PXI-6255 DAQ module recommends the SHC68-68-EPM cable and SHC68-68 cable for each connector. My question, is there any detailed diagrams for the SHC68-68 cable pinout? Is it a one to one with the data acquisition module?

  Hey TreyB

  SHC68-68-EPM cables both SHC68-68 have mappings to pin one.  Links to our documentation for pinout for these cables are below:

  The SHC68-68-EPM cable pinout - http://digital.ni.com/public.nsf/allkb/DE2D842E545DE64B86256F78006EAB1A

  The SHC68-68 cable pinout - http://digital.ni.com/public.nsf/allkb/26223F0B830148FD862577770069EBC4

  You will notice the two cables have different internal shielding, as well as twisted pairs different configurations.  The two are armoured noise outside (the prefix "SH" indicates this).  The SHC68-68-EPM cable is optimized for mixed signals on our X and M Series devices that contain analog and digital channels and offers additional internal shielding between digital and analog lines for better signal integrity. The SHC68-68 cable offers only twisted pair and no armour to protect against digital transients because the cable is intended to be used on the single analog connector.

  Kind regards

• Synaptics touchpad - erratic cursor behavior

  On my Compaq Presario CQ56 (Win7 64 bit) sometimes, the cursor jumps around erratically, usually to the top of the screen that I try to move the cursor down. An external mouse, it works very well. I have the latest version of the driver (15.1.6.64), and I fiddled with the settings of control without result Panel. Sometimes it works fine and I tried to correlate the time that it is wrong with everything I do when this happens (for example if it happens after the laptop has been for a long time) but no luck so far (and in particular, it may happen now, I open the lid or after 10 hours of use). It makes no difference how hard or soft as I press, whose fingers are used, if the rest of my hand is far...

  I also discovered something interesting. In the device settings page, the edge Motion option is disabled. However, under region Motion edge there is a diagram that shows where your finger on the touchpad. Under normal circumstances, the position of the finger is correctly reported, and the mouse cursor also moves that I have spend my finger. When the cursor is wrong, touch the top of the touch pad shows that he thinks that my finger is down. Left and right movements are traced with some degree of accuracy. Because I move my finger down, it suddenly jumps to show that my finger is on the top. Put it down, and yet once it pops up. Meanwhile the mouse hardly moves at all, which seems to indicate that the driver don't is not the operating system to generate messages of mouse movement.

  Any ideas?

  In desperation I completely uninstalled the Synaptics driver, and I now have a touchpad that follows actually just my finger instead of developing its own ideas to dominate the world. It was a bit of a struggle to convince Windows 7 (which has also its own agenda to dominate the world) that I wanted to remove the driver completely, but now I'm using the mouse Microsoft PS - 2 vanilla driver has nothing fancy features which I never use and which seem only to lead to complications, Synaptics bug code and a lot of grief for their unwitting victims.

  Before I uninstalled the Synaptics driver, I continued my comments and noticed that the touchpad seems to work reliably after a restart, until I right click on it. I could imagine that, and I'm certainly not trying to confirm leaving a team of Synaptics software geniuses near my machine again for some time. Still, someone else could benefit from observation. You never know.

  Serve and enjoy, Synaptics.

• How to connect an International ST75 components fluid flow meter to the DAQ system?

  Hello

  I am trying wire a ST75 meter to my DAQ system consisting of a device PCI 6052E DAQ, SCXI 1102 b card and a block to connect SCXI-1300. 1102 b has four 249 Ohm resistors connected to channels 0-3 for use with the current of the flow meter signals.

  The flow meter has two output signals 4-20 my and RTN, SINK, SOURCE and com connections The documentation is not clear how to connect the sensor to the Terminal Board, other than to say if the two output signals is used, one of the sons of RTN are used. So far, I can not get the signal from the flow meter to work in LabView, so I don't know if I have it plugged properly. Currently I have 1 wire OUTPUT on the Terminal Board + CH2, CH2 - wire to the chassis ground terminal and the COM lead on the sensor.

  Thanks in advance.

  Towards the end of the manual there are wiring diagrams:

  http://www.fluidcomponents.com/industrial/library/manuals/flowmeters/ST50, % 20ST 51, 20ST 75% 20Guides %2%...

  SINK/SOURCE/COM are used for pulse ouptuts. It seems that there are two outputs, one for 4-20mA temperature the other for flow.

  The one you need (flow) conjnction with RTN wired to use the + and - (or COM) your DAQ hardware.

  -AK2DM

• HP Pavilion Slimline 400-314: power on password

  A friend brought me his computer for repair and looking for the admin password to start.

  Hello:

  There is a rider of password on the motherboard with that you have to finagle.

  To clear the password BIOS follow these steps:

  1. turn OFF the computer and unplug the power cord.

  2 move the jumper of password of pins 2 and 4 (by default) on pins 4 and 6.

  3. connect the power cord and turn on the computer.  Password should be gone now.

  4. turn OFF the computer and unplug the power cord.

  5. then replace the default password jumper (pins 2 and 4).

  Below the diagram of the motherboard... the password jumper is marked on the motherboard (in white) on the lower right part of the image (where you see blue jumpers).

  You need to understand who is who, because there is no diagram to jump.

  It seems to me that a blue jumper clears the CMOS memory, and another erasing the password.

  

• How are you legal papert in the paper tray?

  The Pro 8600 came with 2 paper trays.  I don't know how to set the paper of legal size paper tray.

  Hello

  Please see the cyan/blue part, there is a diagram that shows you how to extend the status bar.

  Kind regards.