Time capsule and extreme; Cannot create the roaming network

Similar Questions

• Airport Express, Time Capsule and Airport Express using the same network

  Just moved into a new House and this is what I install.  I have 7 Port wired into the House.

  Closet of network in the Garage:

  • Cable modem
  • Airport Express
  • netgear switch 8 ports
  • It works pretty well.  All my wired connections work fine.  Wireless is quite good but cove not enough of space in my house.

  Think about adding my airport express capsule of time in my office - plugged into one of the hard wired connections.  Who works AND let me wish the WIFI?

  Thank you!

  Yes fine, assuming that first test you the Ethernet port in the office by connecting a computer (with WIFI disabled on the computer) using a spare Ethernet cable runs to ensure that the computer can get a good connection in this way.

  Put the airport Time Capsule to create a wireless network that uses the exact same wireless network name and password in your existing network. Apple installation "Wizard" automatically configure airport Time Capsule in the correct setting of the Bridge Mode for the device.

• Cannot create the pool network

  When you try to create a PvDC, I get an error in UI vCD which says 'could not be created.  I drilled down into the error and shows the explanation below.  I also checked the - news and newspapers of debugging on both cells in this environment and they just declare the same data.  When you look on the side of the VSM in this puzzle, the "extended network" seems to have been created no problem for this new PvDC.

  Error response VSM (100): id to load is required for loading. nested exception is java.lang.IllegalArgumentException: id to load is required for loading

  Someone noticed on the things to check?

  There were obsolete entries in the database POSSIBLE vCD caught on during the creation process.  Engineering once deleted the obsolete entries, a repair on the PvDC and/or a recreation of the PvDC enabled the creation of network pool to cross.

• Apple Extreme, Time Capsule and Express on the same system, what is the best way to set it up so that all devices smoothly from one end of the House to another?

  Apple Extreme, Time Capsule and Express on the same system, what is the best way to set it up so that all devices smoothly from one end of the House to another?

  I'm going to assume that you plan to have wireless devices.

  Let's say that the Capsule is your "main" router  If this is the case, then it must be located in the House, so that the distance between the time Capsule is the same for the outside walls of the House.

  Then, on the 'left' side of the House, looking for an airport to midway between the Capsule and time of the outer wall of the House. Do the same thing the 'right' side of the House.

  In other words, each of the two airports that "extend" the wireless signal are located at equal distance from the Capsule of time... but they are in opposite ends of the House.

  If you intend to interconnect all the airports and Time Capsule using a permanent, Ethernet wired... which by far is the 'best' way to put in place a network in terms of performance and reliability... then you can locate one of the devices anywhere you want.

• setting up time capsule and express wired after disconnection of the airport

  I have a 2 TB Time Capsule and three 3 wired express airport throughout my house.  I know that when I added first the cable express, that I had to call apple to change some settings.  Now I can't service because they are more than a year and after a recent quick breakdown (two or three) power is the airport expresses link is more and a bunch of my settings seem to have changed on the Time Capsule.  Any help would be greatly appreciated.  Thank you

  If you think there are setting changes, then it would be better to start over.

  • First of all, you want to make a 'factory' reset on all of your base stations. This will return them to their "out-of-the-box" configuration Once finished, leave them turned off.
  • Then, we put up the Time Capsule (TC). Since it has been reset, it will broadcast a Wi - Fi unsecured network with a network name of something like: Apple network NNNNNN.
  • Use AirPort Utility on your iPhone, Mac or PC to configure the TC as a stand-alone wireless router. In other words, configure it to provide a secure WiFi network.
  • Once the TC has been configured, verify that the clients on your network can access the Internet with it.
  • If he succeeds, proceed to the next step. If this is not the case, stop and post back with your results.
  • We will now configure all of your base stations for a roaming network.
  • Power-up one of the three stations based AirPort Express.
  • Once again, you will need to use AirPort Utility to continue. The utility must now find the Express, and if all goes well, it will offer to the Express allows to extend the TC using Ethernet. It's what you want and just go through the steps automated window 'Installation '. And then on actually.
  • Do the same for the other two express base stations.

• How can implement you not with Tim Capsule and AirPort their simulation on the iMac?

  Hello

  How can implement you not with Time Capsule and AirPort their simulation on the iMac?

  I don't know what you're asking.

  AirPort Extreme is a wireless router.

  A Time Capsule airport is an AirPort Extreme with a built-in hard drive for data storage.

  An iMac is a Mac computer.

  An iMac is not a wireless router, so he is unable to perform the functions of a wireless router.

• Cannot access Time Capsule and MacBook Pro on Windows task force immediately after upgrade to Vista professional professional 7

  I had a Windows workgroup for years, linking the PC and Mac, but also a Linkstation network through a Time Capsule router/Hard Drive Combo.  Immediately after the upgrade from professional Vista to 7 Professional on my Sony Vaio VGN-Z750D, I can see the Time Capsule and MacBook but cannot access it.  I am able to access the Linkstation - system wonder a user name and password, and I have immediate access.  However, the system does not n = me a username and password when I try to access the two Apple products.

  Interestingly, I can access the Vaio MacBook, in providint the username and password for the Vaio.

  Please notify.  Thank you.

  IT FIXED!  Found the answer on the W7 Forum

  Access to Mac OS X Windows sharing Windows 7
  Windows 7 will not work with the Mac OS X Windows support for default share file. If you try to access a shared folder on Mac OS X, W7 will display a logon error repeatedly.
  The problem is that W7, by default, will only use NTLMv2 for authentication, which is not supported by the service of sharing of Windows of Mac OS x.
  The other problem is that safety minimum Session for NTVLM SSP based Clients.
  To work around this problem:
  1. in W7, open the control panel
  3. double-click on Administrative Tools
  4 double click on local security policy
  5 expand "Local policies" and select "Security Options".
  6. locate "network security: LAN Manager Authentication Level" in the list and double-click it.
  7. change the setting of "NTMLv2 only send responses" to"send LM and NTLM - use NTLMv2 session if negotiated"
  8. network Security: minimum session for the NTLM SSP (including secure RPC) Clients security
  9. change the setting of "128-bit" unchecked (No Minimum)
  10. click on OK

• Error message: cannot create the folder C:\Documents and Settings\Marlon\Local Application BVRP Software\NetWaiting\MoHlog.txt Settings\

  I recently had a problem with the virus 'Restore Windows'. I was able to get rid of it with Malwarebytes antivirus scanner, but when I turn on my computer I get this error message.
  Cannot create the folder C:\Documents and Settings\ of Settings\Marlon\Local Application BVRP Software\NetWaiting\MoHlog.txt
  
  
  I'm no expert, but I feel that my C drive disappeared, or at least has been hidden. My documents, pictures and music files are all empty. My programs (start > all programs) have been removed and deleted the shortcuts on the desktop. When I go to my computer, my personal and shared document files are not accessible. Under the description it says that they are hidden. My local disk (c) is also empty, but there is still very little space which suggests that programs and files have not been deleted.
  Is it possible to recover my files?
  Thank you

  Hello

  MoHlog.txt file is related to the software of modem on the computer, you can uninstall and reinsta it check if it works.

  Also scan your computer for any infection by virus still present on the computer using any scanner online.

  You can also try the system restore to the point before that the computer has been infected by the virus and check if it helps.

  Good luck!

• Empty Device Manager and for error message "cannot create the enumerated device root need to install Parallels paravirtualization pilot".

  Original title: Device Manager empty

  I have Windows XP Service Pack 3 installed in a Bootcamp partition on my Intel iMac. I can detect and install new hardware such as USB keys. However, the Device Manager window is blank - how can I get the window to display the devices connected to the computer? I am also unable to install Parallels tools when I use Bootcamp as a virtual machine. The error message "cannot create the 'root-enumerated device' necessary to install Parallels Paravirualization driver.

  Hey Harcjk,

  For your first question, go through this article.

  None of the items appear in the device list manager when you open
  http://support.Microsoft.com/kb/311504

  For the second question, here are some suggestions:

  Method 1: Uninstall & install Parallels tools

   

  NOTE: we highly recommend you make a backup of the virtual machine before you continue.

  a. start your virtual machine and cancel the installation of Parallels Tools Wizard.

  b. Click Start--> Panel--> Add / Remove programs and remove the Parallels tools in the list of applications.

  c. restart Windows.

  d. install the Parallels tools by clicking on the Virtual Machine--> install the Parallels Tools.

  Method 2: Uninstall antivirus software

  If the problem persists, try the following:

  Temporarily uninstall all the antivirus software to the virtual machine and repeat steps of the "Uninstall & install Parallels Tools" section above.

  Note: Don't forget to install the back antivirus software, once the problem is resolved.

   

  Method 3: Uninstall, clean & install Parallels tools

   

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following windows Help article.

   

  How to back up and restore the registry in Windows XP

  http://support.Microsoft.com/kb/322756

  a. If the problem persists, try the following:

  b. start Windows.

  c. go to "Start" > "Control Panel" > "Add/Remove Programs" and uninstall theParallels Tools if it is present.

  d. go to 'my computer' > 'C' drive > "Program Files" > "Parallels" folder and delete the "Parallels Tools" folder, if present.

  e. click the Windows 'Start' menu-> 'run' and type 'regedit'. Click OK.

  f. in the registry editor, go to "My Computer\HKEY_LOCAL_MACHINE\SOFTWARE\Parallels" and delete the heading "Parallels Tools" and go to "My Computer\HKEY_CURRENT_USER\SOFTWARE\Parallels" and remove the 'Tools' section.

  g. restart Windows.

  h. now install Parallels tools in the 'VM' menu on the Parallels Desktop menu bar, while Windows is running.

  I hope this helps.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• I can't join or create a group of houses in windows 7 it says my pc and laptop cannot create a how I should I followerd all articles I can find on the microsoft kills site

  I can't join or create a group of houses in windows 7 it says my pc and laptop cannot create a how I should I followerd all articles I can find on the microsoft kills site

  Hey borq Queen,.

  Welcome back you hear. If, after completing all the steps below, you are still unable to create or join a homegroup, I think that the issue is to do with IP/V6.

  Check your setting of the adapter for IP/V6. Your network connection must have IPv6 enabled to create or join a homegroup. If it is disabled, follow the steps below to activate it.

  (1) right click on the network icon and select open network and sharing Center.

  (2) in the window that appears, select change the parameters of the map.

  (3) in the network connections window, select the connection to the Local network for the Integrated NIC, and then change the settings for this connection or the file > properties.

  (4) in the connection properties page, check the box for Internet Protocol Version 6 (TCP/IPv6).

  Close all windows and restart your system.

  Try to create a homegroup.

  You should be able to create or join one after the activation of the IP/V6.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think

• Time Capsule and Airport Express keeps disconnecting

  I have a problem setting up the network at home. I have a Time Capsule that is connected to a router Huawei, the Capsule is set to 'Create a wireless network' and router mode "Off (bridge mode).

  It was great to all workers and I get 2.4 Ghz and 5 GHz networks.

  Today, I bought an Airport Express so I can extend the wifi signal in the new section of the House, I tried to connect it to the time Capsule because 'Extend a wireless network' for a while, it would connect and everything seems fine and then begins the two TC & AE drop and reconnect again and let down once again , the led starts between green and amber shifts from time to time and keep doing that... The WiFi keeps fall signals and reconnect!

  I'm not sure what the problem... ! tried to set up two or three times but nothing seems to work. But once I turn off the AE, the TC begins works very well!

  Here is how my network configuration must be:

  Wall -> RJ11 >- Huawei -> Ethernet >- TC ... > WiFi >... AE 

  Note: when I connect the AE to transport CANADA the 1st time, this pattern was shown in Airport utility:

  Internet > TC > AE

  but it would be still lower, after the reset of the AE several times and tried to configure several times, now what I see is that both are connected to the Internet icon somehow!

  Any help!

  Begin by looking at the location of the AirPort Express to the TC Terminal. It is in the same room, another room or different floor? Another room or floor, if that it the basic construction building materials used in the walls or the ceiling in your home?

  What exact models are each of your base stations?

• KB2628259 doesn't install, cannot create the directory or file. Anyone know of a solution?

  KB2628259 doesn't install, cannot create the directory or file. Anyone know of a solution?

  Hi dakota25,

  ·         Did you do changes on the computer before the show?

  ·         You are able to install other updates successfully?

  ·         You get the error message?

  Follow these methods.

  Method 1: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Put the computer in a clean boot state to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 3: You can also manually install updates (KB number) by downloading from the Microsoft Download Center.

  http://www.Microsoft.com/downloads/en/default.aspx

  Method 4: Follow the steps in the article.

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  You cannot install some programs or updates

  http://support.Microsoft.com/kb/822798

• Cannot create the C:\WINDOWS\system32\drivers\drive.sys file

  Cannot create the file 'C:\WINDOWS\system32\drivers\drive.sys '. The process cannot access the file because it is being used by another process.

  I get this error message all the time on my desk. No matter what I do, internet research, watch videos, listen to music, work offline, it does not apply to just be online. I really want to know how to solve this problem, I searched everywhere I could, and I can't find again no anwer. Please reply and if you want more information, then I'll be happy to provide.
  Thanks for your time.

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:
  Start the computer in safe mode and check if the same problem occurs:
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Method 2:
  Try to perform the clean boot and check if it helps:
  http://support.Microsoft.com/kb/929135

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  It will be useful.

• DBCA cannot create the database in 12 c in Windows

  Hello

  After the installation of Oracle 12 c on R2 Windows Server 2012 and successfully running the netca command to configure the listener, I run with the DBCA tool question

  It throws an error message of "Recovery Manager could not restore the data files"

  I looked at the log files, here is some information:

  Corrupt block 1 found during the backup piece, reading file=C:\ORACLE\PRODUCT\12.1\DBHOME_1\ASSISTANTS\DBCA\TEMPLATES\SEED_DATABASE. DFB, corr_type = 4

  Review of blocknum = 1, file=C:\ORACLE\PRODUCT\12.1\DBHOME_1\ASSISTANTS\DBCA\TEMPLATES\SEED_DATABASE. DFB, found the same corrupted data

  Not sure if this helps, but I am attaching several log files to help debug the problem.

  I read the post DBCA cannot create the database in 12 c, but it doesn't quite have an answer.

  Any help is appreciated.

  Thank you

  Pranav

  Looks like a bad installation or a bad block on your disk. Have you tried creative using the "Custom Database" model in the wizard dbca (one that does not come with the data files)? It will take more time to create, but shouldn't read the dbca reported as corrupted file

• Error Lightroom: You cannot create the required folder

  Hello

  I have an error with the Lightroom program. I installed from application cloud creative and seems to be all right. When I open the program I get the error:

  There was an internal error. You cannot create the required folder: / users / lived / Library / Application Support / Adobe / Lightroom / metadata Presets.

  

  Report an error by CAT, but apparently there are problems and not receive messages from operators. They worked on my files internally and now have problems because the app says that some files cannot be synchronized.

  Can someone help me? Please

  Hi viviang,

  Greetings!

  There is a permission problem.

  Try to give permissions to both libraries (library system & user library) and the Applications folder.

  For the Applications folder

  ---------------------------------

  Open Finder

  On the left panel, you will find applications-> folder, right-click on this (CTRL + click) and then click on read the information.

  Inside you will find sharing and permissions - Click on this

  You will find an icon of padlock at the bottom right, click on the lock icon, and then he could ask your mac password, please put to.

  Now, click the little plus (+) and then add the users you want to, please make sure that you add the admin account.

  Give read and write at all.

  Click the gear icon at the bottom of the get info window and choose "Apply to the elements included" it appears a message that the changes cannot be undone - click OK to that.

  This measure will apply privileges and which can take some time depending on the size of the file.

  Once this is done, click the lock icon, and then close the get info window.

  Done with file applications here.

  For the user's library

  -----------------------

  Open Finder

  Click OK at the top of the page and select 'go to folder '.

  Type "~ / Library ' and press go

  Click (CTRL + click) on the library folder, if you are within this library, you can right click (ctrl + click) on an empty space between folders and then click on information

  Inside you will find sharing and permissions - Click on this

  You will find an icon of padlock at the bottom right, click on the lock icon, and then he could ask your mac password, please put to.

  Now, click the little plus (+) and then add the users you want to, please make sure that you add the admin account.

  Give read and write at all.

  Click the gear icon at the bottom of the get info window and choose "Apply to the elements included" it appears a message that the changes cannot be undone - click OK to that.

  This measure will apply privileges and which can take some time depending on the size of the file.

  Once this is done, click the lock icon, and then close the get info window.

  Made with the user here library folder.

  For the library system

  ----------------------------

  Open Finder

  Click OK at the top of the page and select 'go to folder '.

  Type "/ Library" and press go

  Click (CTRL + click) on the library folder, if you are within this library, you can right click (ctrl + click) on an empty space between folders and then click on information

  Inside you will find sharing and permissions - Click on this

  You will find an icon of padlock at the bottom right, click on the lock icon, and then he could ask your mac password, please put to.

  Now, click the little plus (+) and then add the users you want to, please make sure that you add the admin account.

  Give read and write at all.

  Click the gear icon at the bottom of the get info window and choose "Apply to the elements included" it appears a message that the changes cannot be undone - click OK to that.

  This measure will apply privileges and which can take some time depending on the size of the file.

  Once this is done, click the lock icon, and then close the get info window.

  Done with the record of the library system here.

  Please let me know if it works

  Please note: do not just right-click on MAC HD complete and provide all permissions that can bring the MAC in any startup mode.

  Concerning

  Jitendra Khatwani