To sttartup error 'loading\3\dlcxtime.dll run.dll error. "

Similar Questions

• I get error loading \3\DLCXtime.dll

  When I start up I get error loading \3\DLCXtime.dll
  The specified module could not be found?

  How to solve this?

  Thank you
  Arthur H

  Hello

  DLCXtime.dll is part of your Dell printer drivers. You probably need to reinstall. Also contact Dell Support
  and their forums for known problems.

  Dell drivers
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell support
  http://support.Dell.com/

  Dell forums
  http://en.community.Dell.com/forums/
  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• At the start I have receiver error loading \3\DLCXtime.dll

  When I boot I get "error loading \3\DLCXtime.dll".
  The specified module could not be found.

  I know that this has to do with my old Dell printer driver drivers, but I've improved my printer and no longer have the old Dell on my system. I thought that I had uninstalled all the software from Dell, but obviously not.

  What should I do to rid my computer of this left over trash? Thanking you in advance.

  Kind regards

  G. Bowes

  E-mail address is removed from the privacy *.

  Hello

  DLCXtime.dll is part of the Dell printer drivers. You probably need to reinstall to check the status.

  You can contact Dell technical support for known problems.

  You can view this issue in the community Dell here: http://en.community.dell.com/support-forums/peripherals/f/3528.aspx

  You will get updates Dell drivers here: http://www.dell.com/support/home/us/en/19?c=us&l=en&s=dhs

  Let us know if you need assistance with any windows problem. We will be happy to help you.

• Fatal error: unable to load library "pdh.dll."

  When I double click on Skype icon, a dialog box appears. It says "Fatal error" at the top, and inside, it says: "cannot load library 'pdh.dll.'" "I can't Skype to open at all.

  I used Skype without problem the day before, and I did nothing for all the files or anything like that. I don't think so.

  I restarted my computer, uninstalled and reinstalled Skype and entered %APPDATA%\microsoft\windows\sendto and renamed the Skype folder, tried to open Skype, then renamed the file back again. None of this has worked.

  I did a scan for Malware, and he came clean. I am running a virus scan.
  Can someone help me?

  Try to run the tool (sfc.exe) System File Checker

  http://support.Microsoft.com/kb/929833

• I have a Dell computer that came with Windows XP Home edition. When I start my computer the monitoring of ERROR appears: RUNDLL error loading \3\DLBUtime.dll

  Error loading \3\DLBUtime.dll

  I have a Dell computer that came with Windows XP Home edition.  When I start my computer the monitoring of ERROR appears: RUNDLL error loading specified not found \3\DLBUtime.dll module

  I just click 'ok' and he goes, but, as for what it stop popping up everytime I start my computer.

  Can someone help me with this?

  Aprilm,

  You are LuLu5119, who posted a question last August?

  If this isn't the case, you should have started your own thread.  If so (and even if not), you should have responded to questions about Dell printers.

  Assuming that you complain of a "Error loading \3\DLBUtime.dll" message that appears when you start your computer, you should know that the DLBUtime.dll file probably has something to do with the software from Dell which has been partially deleted, but could also be indicative of malware as well as partially withdrawn.

  In both cases, the best way for start you to prevent the message at windows is to download Autoruns http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx

  Install the Autoruns and let it complete the scan of your computer.  Then click on the "Connection" tab and uncheck the following entry:

  Look for an entry that has 'DLBUCATS' in the first column.  If you do not see that, look for "rundll32 \3\dlbutime.dll" in the last column ("path of the Image).

  Uncheck that entry, close Autoruns and restart your computer.  You should get is no longer the message.

  If for any reason, you find later that you need dlbutime.dll running, run Autoruns and check the box. If you decide that you need never again, run Autoruns, right-click on the entry and select Delete.

  As General precautionary measure, in case your entry dlbutime.dll was related to malicious software, rather than the Dell printing software, download the following free scanners:

  MalwareBytes Anti-Malware: http://malwarebytes.org/
  SUPERAntiSpyware Portable: http://superantispyware.com/portablescanner.html

  For MalwareBytes Anti-Malware, download, install, update and run.
  For Portable SAS, follow the instructions on the Web page (note that the instructions assume that you use a different computer to download; if you're not, just make a note of the name of the file).

• Error Msg: your msg error loading win\jquarayeh.dll

  Each time computer is the startup error msg pop up: your error msg load win\jquarayeh.dll.  What is this msg and how to fix it?

  Each time computer is the startup error msg pop up: your error msg load win\jquarayeh.dll.  What is this msg and how to fix it?

  You are not charged by the letter when you post here.  Generally, it will display the full error message.  However...

  Looking for errors like this by doing a search on Google for the name of the file.  Usually, they turn up without success.  There is no success for jquarayeh.dll

  When a search in no hits or suspicious hits result, the answer is usually that the file in question is linked to the malicious software and your anti-malware application has deleted or quarantined file, but left to the Windows registry entry that tries to start the malicious software when you start your computer.

  First of all, download, install, update and run full scans with two of these free analytical tools:

  MalwareBytes AntiMalware
  SUPERAntiSpyware

  Do not run the scans at the same time.  They can take some time, so start an and then go for a non computer chore for awhile.

  If the scans does not solve the problem (and they can't, because the actual malware file has already been processed), then download and run Autoruns.  Click on the "Connection" tab and look in the column 'Image path' for the dll named in your error message.  If it is not displayed in the connection tab, click the "all" tab and use the file > search tool.  A characteristic of the search of Autoruns tool is that you must move the selection under the element line "found" before you "Find Next."

  Once you find the line with the file in question, either "delete" or (if you want to be safer) uncheck the box.  The latter prevents the line running, but you can reactivate it later by removing the check mark.

• At the start of XP, make error rundll error loading \3\lxcctime.dll

  When windows load I get this error rundll error loading \3\lxcctime.dll. How can I fix it?

  OS: windows xp home edition. recently had a lot of viruses on the computer. mainly Trojan viruses

  When windows load I get this error rundll error loading \3\lxcctime.dll. How can I fix it?

  This error is related to your Lexmark printer.  The following procedure may solve this problem, although I've seen conflicting reports.

  Follow the instructions here to uninstall and reinstall the printer software: Article 1.  Between steps 4 and 5, perform the following steps (if you can not complete step 4, post back with this information):

  • Open a command prompt window (start > run > cmd > OK)
  • Type the following commands in the black command prompt window, pressing ENTER after each line.  Note that there is a space after the = not before

  net stop spooler
  dependent on the spooler of sc config = RPCSS
  net start spooler
  output

  To step 6, start here: http://support.lexmark.com/index?page=home&locale=EN&userlocale=EN_US&segment=DOWNLOAD

• At the start, get error loading driver udesiab.dll

  on startup, I get an error loading driver udesiab.dll, no matter who with an idea what is this driver or how can I remove it?

  Hello

  read the slot results in google for "udesiab.dll."

  http://www.google.com/search?hl=en&source=HP&q=udesiab.dll&aq=f&aqi=&AQL=&OQ=

  There is no search results for her that usually indicates that it is malware or a stay starting entry of for her

  to be on the good side for malware scan;

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If the error persists after scanning use this program to out startup

  This utility, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configure Autoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services even more. Autoruns goes way beyond the MSConfig utility bundled with Windows Me and XP.

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902

• Startup error: DLL Load error can not load the resource dll: REPLRES. RLL the specified module could not be found

  Original title:

  ReplSync.dll - error loading DLL cannot load resource dll: REPLRES. RLL the specified module could not be found

  I get this error message whenever I start my computer: replsync.dll - DLL Load error can not load the resource dll: REPLRES. RLL specified module is not found Help please?  Thank you!

  Hello
  You did changes to the computer before the show?
  Method 1:
  Step 1:
  
  You can try to start in safe mode and check if the problem persists.

  The Advanced Boot Options screen lets you start Windows in advanced troubleshooting mode. You can access the menu by turning on your computer and pressing the F8 key before Windows starts.

  Some options, including the mode safe mode, start Windows in a limited State, where only the essential is started. If a problem doesn't reappear when you start in safe mode, you can eliminate the default settings and basic device drivers and services as a possible cause.

  Advanced startup options
  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode
  
  Step 2:

  If the problem does not occur in safe mode, and then try to perform the clean boot and see if the problem still occurs. Clean boot helps eliminate software conflicts. For more information, see the following link:

  http://support.Microsoft.com/kb/929135

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the article mentioned above.

  Method 2:
  
  You can run Windows Defender Offline tool.

  See the following link for more information about the same:

  What is Windows Defender in offline mode?

  http://Windows.Microsoft.com/en-us/Windows/what-is-Windows-Defender-offline
  
  Windows Defender Offline: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows/Windows-Defender-offline-FAQ
  
  Note: data files that are infected must be cleaned only by removing the file completely, which means there is a risk of data loss.

  Method 3:
  
  Try the SFC (System File Checker) scan on the computer.

  SFC/scannow is a very useful command that you can use in any version of Windows. When the SFC (System File Checker) command is used with the/scannow switch, the tool analyzes all the important files of Windows on your computer and replace if necessary.

  Missing and the corruption of the operating system (like many DLLs) files are probably the main cause of the major problems of Windows. In view of this, plus the fact that the SFC/scannow is completely automatic and very easy to use, the tool should be usually one of your top not troubleshooting.

  Reference:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Let us know if it helps!

• How do I resolve error that "Acrobat failed to load its core DLL?

  How do I resolve error that "Acrobat failed to load its core DLL?

  I have already tried to remove and reinstall, still get the same error message. I am running Windows 7 and have Norton Antivirus.

  http://helpx.Adobe.com/Acrobat/KB/reader-core-dll-error.html

• \3\DLCXtime.DLL startup error, Windows 7 64 bit

  I have error \3\DLCXtime.dll at startup. I used to have a Dell AIO 926 installed on this machine, but it is now gone from my home. I can't remove the software from Dell AIO 926 of the Remove Programs list, and I can't reinstall the drivers again found in http://www.dell.com/support/drivers/us/en/19/DriverDetails/Product/dell-926?driverId=R150575&osCode=W764&fileId=2731117707&languageCode=EN&categoryId=PR without physically reconnect the printer.  Any help is appreciated!

  Johnny

  Hi, Johnny,.

  Follow these steps to remove drivers.

  Start > type services.msc
  Press enter
  Scroll down to print spooler
  Right-click on the spooler > select Properties
  Make sure that the Startup Type is set to automatic
  Under the service stop status
  Wait for Windows to stop the printer
   
  Control Panel > open the printer folder
  Right click on the printer icon > select Open
  Do you see the documents listed in the queue for printing?
  Click file > cancel all Documents
   
  Start > right click on computer > select Manage
  Click on continue on window UAC (Vista, Windows 7)
  Select Device Manager
   
  Click on the + sign next to Ieeee... compatible printer
  Right-click on the printer driver and select uninstall
  Click on the + sign next to the imaging device (s)
  Right-click on the printer driver and select uninstall
  Click on the + sign next to printers
  Right-click on the printer driver and select uninstall
  Click on the + sign next to Bus USB controllers
  Right-click on the printer driver and select uninstall

  Go to uninstall programs in Control Panel

  Remove the drivers for the printer does not exist
   
  While the printer is turned on, unplug the cable from the rear
  Unplug the cable from the wall outlet
   
  Wait 5 minutes
   
  Plug the cable into the wall jack, and then the back of the printer
  Restart the computer

  Go back, and then restart the print spooler
    
  Go to the manufacturer's website and search for updated drivers

  Dell drivers and support
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/

• Impossible to access parameters for laptop and receive an error message saying "runtime error!" Program c:windows/system32/Dllhost.exe R6034. A request did try to load the wrong C run-time library. »

  Original title: laptop - unable to access settings.

  I can't access "pc settings" on the start menu. When select, goes to white screen, returns to 'start '. Error is displayed on the desktop = "runtime error!" Program c:windows/system32/Dllhost.exe R6034. A request did try to load the wrong C run-time library. "Any ideas on how to solve this problem? Thank you

  I found the answer here http://blogs.technet.com/b/ouc1too/archive/2013/10/19/windows-app-store-doesn-t-load-after-8-1-upgrade.aspx you just have to change application manifest path, in order, to fix all other applications

• When I run the exe file, it should load the niscope_32.dll why?

  Hello:

  I used scope in my program functions,

  and then I did it in the exe file and the installation file,

  but when I make them to another computer,

  To load the niscope_32.dll, what should I do?

  Hi ylongwu,

  You will need to install the driver OR-Scope on the deployment computer so that the code you can call the driver. You can download the driver from our Web site at drivers and updates the link below by searching our driver OR-Scope and choosing the appropriate version. I also recommend that you include the NOR-Scope driver as an extra Installer for your executable. In the setup of window construction there is a category called additional installers where you can choose the drivers and execution engines to install with your executable file. I've included a screenshot to show what it will look like for LabVIEW 8.x.

  Drivers and updates
  http://Joule.NI.com/nidu/CDs/fn/p/lang/en

  

• Half-life 2 says failed to load the Launcher DLL specified module could not be found

  Failed to load the Launcher DLL:

  the specified module could not be found

  Hi Madoo17,

  Welcome to the community of Microsoft and thanks for posting the question. I've surely you will help find a solution on the issue.

  1. Once you get this error message?

  2. it worked before?

  3 did you changes to the computer before the show?

  Perform the steps:

  Method 1:

  Put the computer in a State of boot is a way to know which application is causing this problem.

  To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Step 1:

  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

  Follow the steps in the link below to do the same thing:

  How to configure Windows XP to start in a "clean boot" State

  Note: After troubleshooting, be sure to set the computer to start as usual as shown here:

  Step 2: To configure Windows to use a Normal startup state

  After you have used the boot is a way to solve your problem, you can follow these steps to configure Windows XP to start normally.

  a. Click Start and then click Run.

  b. type msconfig and click OK. The System Configuration Utility dialog box appears.

  c. click on the general tab, click Normal Startup - load all services and device drivers and then click OK.

  d. When you are prompted, click on restart to restart the computer.

  Method 2: Use the (SFC) System File Checker tool.

  SFC system gives an administrator the ability to scan the files all protected to check their versions. If the System File Checker detects that a protected file has been replaced, it retrieves the correct version of the file in the folder cache (% Systemroot%\System32\Dllcache) or the Windows installation source files and then replaces the incorrect file. System File Checker verifies and repopulates the cache folder also. You must be logged in as an administrator or as a member of the Administrators group to run the System File Checker.

  Check out this link to do the same thing:

  Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)

  Hope this information helps. Please reply back with the State so that we can help you.

• Loading of the DLL string using the Code Library function node

  I experience now with the element of Code Library function node... what I wanted to do are, for example, I have compiled a. DLL file... which has a function that returns the pointer to string... function looks like:

  / * This function returns a pointer to the character string * /.

  char * pchar (int n)

  {

  char * str [] = {"error", "String1" and "Word2", "3"};

  Return ((n! = 1) & (n! = 2) & (n! = 3))? Str [0]: str [n];

  }

  but when I load into LabView DLL, a part of the chain on the screens to Panel frontal trash... any ideas why?

  p.s. when I do even with integer values... say my job is like int x = 5; Return x; and then I load in LabView to the digital indicator... it works great!

  So any ideas?

  thanx

  Cyrax says:

  I experience now with the element of Code Library function node... what I wanted to do are, for example, I have compiled a. DLL file... which has a function that returns the pointer to string... function looks like:

  / * This function returns a pointer to the character string * /.

  char * pchar (int n)

  {

  char * str [] = {"error", "String1" and "Word2", "3"};

  Return ((n! = 1) & (n! = 2) & (n! = 3))? Str [0]: str [n];

  }

  but when I load into LabView DLL, a part of the chain on the screens to Panel frontal trash... any ideas why?

  p.s. when I do even with integer values... say my job is like int x = 5; Return x; and then I load in LabView to the digital indicator... it works great!

  So any ideas?

  thanx

  You cannot return a pointer to the data stored on the stack. At the time when the function returns, the stack is reset to the State before the call to the function and in a multithreaded as LabVIEW environment probably long reused for other things when LabVIEW gets around to actually copy the returned pointer data.

  Since it is a read-only variable, you could create a permanent memory for string storage by declaring your variable static. This will create a memory area allocated globally for the string data (and also cause a compile error when you try to write in this area somewhere in your code, which is a good thing).