Transmitting the power of Linksys WRT54GL v1.1?

Similar Questions

• Transmitting the power of version 3.1 of the WAP54G

  Hello

  someone at - it known the transmitting power (in mw) of version 3.1 of the WAP54G?

  Thank you.

  This is the firmware part only third I know for the WAP54G V3.x with the function you're looking for without a lot of other useless to play. Simply go to advanced wireless settings, select the power and configuration of the antenna and your done.

  Note: The maximum power output is 84mw, and change it to any value that has no effect. Something like netstumbler to measure the new signal at the level of the customer in order to give you an idea on the comparative difference in signal.

  Concerning

  Fred

• Linksys WRT54GL v.1.1, not Internet, 127.0.0.1

  Dear friends,

  I wonder what happened after the change to my dorm to the normal IP proxy automatic. With the proxy of my router (WRT54GL v.1.1) worked without problems and now it doesn't.

  A friend bought Apple Airport as he says that the old technology does not support this network more. The thing is when I connect the RJ45 cable to my internet computer without seting, I get up, everything is automated.  So I can't believe that my router (WRT54GL v.1.1) is not able to do too much.

  When I connect (via The DHCP Auto - Configuration) internet even to my router (WRT54GL v.1.1) I get the following information under status:

  	IP address:	127.0.0.1
  			Subnet mask:	255.0.0.0
  			Default gateway:	0.0.0.0
  			DNS 1:
  			DNS 2:
  			DNS 3:
  			MTU:	1500

  I downloaded

  Firmware version:

  4.30.18 build 6, 8 January 2016

  You have an idea, what happens? Is this router linksys WRT54GL v.1.1 outdated and I should now get Apple Airport?

  Thank you!

  Let's get this work, ceciliamaiitre. 127.0.0.1 is the loopback Internet protocol (IP) address also known as localhost. The address is used to establish an IP connection on the same computer or computer used by the end user.

  Besides, who is your ISP? It is possible that the IP from the modem is on the same range of router that is causing this conflict or this challenge. To resolve this problem, change the 3rd octet of the IP address of your router (e.g. 192.168.2.1) or you can simply use 10.10.10.1. Don't forget to release and renew the IP address. And if there is still no internet connection, just powercycle the router.

  Jay-15354

  Linksys technical support

• Unable to connect to the Administration of Linksys to my WRT54G v.6 page

  Hello

  Recently, I moved into a new House and brought my old router with me.  I set up this router to my former place long ago, but when I hooked it up here, I am unable to connect to the Admin of Linksys page (http://192.168.1.1 for example).  I think that I changed the router what IP to 192.168.1.101... it was a long time ago so I don't remember exactly.  I tried find what it was by typing "ipconfig" in the command prompt and using the address "Default gateway" IP address as the address of router, but that has not worked.

  I tried to reset the router to factory default settings by pressing the button of reset for 30 seconds, then connect to http://192.168.1.1 but it does not help.  When I release the reset button, just power light continues to blink rapidly until I unplug the router.

  I can access the internet without any problem, but I noticed that I connect my router differently than the instructions provided here.  I connect an ethernet cable from my modem to 1 of the 4 ports on the router (just like my laptop) rather than the port of 'internet' on the back.  Don't know if that is related or not, or even what is the cause.

  I use Windows Vista on my laptop if it makes a difference.

  Thanks in advance for your help,

  Ryan

  The modem must be connected to the internet port of the router and the conputer on one of the 4 ports on the router... Now, check if you are able to ping the default gateway of the router. If you get 4 answers then, make broser on the computer settings... Open an IE, click Tools > Internet Options, then click on delete and delete all the files, cookies, history, forms... GoTo 'Connections', make sure that never Dial a connection is selected, click on network settings and make sure that all the options are unchecked... Once you are finished, click OK... Close IE and reopen...

  Now, try to open the linksys configuration page by typing 192.168.1.1 in the address bar. You can also try another computer.

• Can't make an Apple iPod Touch to connect to my new Linksys WRT54GL Wireless router.

  Hello.

  I'm trying to set up the iPod Touch (bought for more than a year; using v2.2 (5 G 77) firmware) of the of my client to connect to my new encrypted Linksys WRT54GL Wireless router. After we entered the password (too many sensitive cases and WPA shared key) as five times, he said "Failed to join"FooBarWRT54GL"" immediately.

  The router uses the latest firmware v4.30.13 with these wireless settings:
  Wireless network mode: Mixed (you want to support the devices/clients and B).
  Wireless Network Name (SSID) example: FooBarWRT54GL
  Wireless channel: 1-2, 412 GHZ
  Security mode: WPA2 Personal
  WPA algorithms: TKIP + AES
  Example of WPA Shared key: Abunchofletters aspacetoo

  I guess that this device can do WPA Personal as she saw the WAP and requested a password. We have not had any problems with a year old 15 "MacBook Pro (2.4 Ghz and Mac OS X 10.5.8) and it's easy as cake.

  Any ideas? Thank you in advance.

  I finally got to work, with the help of Apple at the forum: http://discussions.apple.com/thread.jspa?messageID=10650288... I had to do a manual configuration. Don't know why selecting the WAP and entering his password/password didn't work.

• Protect a Linksys WRT54GL from access (ignore software config / selector)

  Hello

  hope you will be able to help.
  I have a Linksys WRT54GL - OF and my problem is,
  that someone manipulates the router.

  Is it possible to protect the router in this way
  It is not possible to reset the router

  using the reset button

  NOR by the Linksys software tool?

  Especially the software tools is the problem - I fear.
  someone reset / manipulate the router using software.
  Is there an option?

  Many thanks in advance,
  T

  1. block the router to prevent people to press the reset button.

  2. to avoid changes via the web interface defined a strong admin password.

  Otherwise, try 3rd party firmware that you can configure just about in everything you like.

• Linksys WRT54GL do not connect for its "incoming log Table?

  Hello.

  Is it me or does Linksys WRT54GL v1.1, with its v4.30.13, no newspaper "Incoming log Table" firmware? I see nothing in http://192.168.0.1/Log_incoming.asp (Yes, I changed its default IP 192.168.1.1). However I can't get logs in his outgoing. I guess only inbound log table is logging blockades and other data.

  Thank you in advance.

  I think that there is a problem with the firmware. Read this.

• macOS Sierra - press and hold the power button to enter the mode 'sleep'

  I recently updated my MacBook Air (13 inch, early 2015) model of El Capitan macOS Sierra 10.12. Before the update, hold down the power button / stop for 2-3 seconds, put the machine in standby mode. It does not properly after the update. Release the power button to switch to sleep mode works only once after each time you start the machine.

  I know he has an option to set the mode of sleep using Ctrl + button / stop and by selecting one of three options to restart, sleep and Shutdown, but who needs 3 more click click and is not fast. Also, independently of any application that is open, pressing the button walk / stop worked fine before the update, but now I need to be on the desktop even do Ctrl + Power button work.

  All patches available for it? Miss me the old way of put my Mac to sleep I do not remember if I did some tweak in my Mac, or was it a default feature...

  Greetings jainam2209,

  Thank you for using communities of Apple Support. It seems you want to put the Mac to sleep, but it does not always work.
  I would recommend read you these articles, the first article explains the ways that macOS Sierra is supposed to go to sleep.
  The second article can help if the computer won't sleep when you're trying to sleep.
  

  macOS Sierra: put your Mac to sleep

  macOS Sierra: If your Mac won't go or stay asleep

  Take care.

• After resetting the iPad to default it show that the power cord is trying to connect to iTunes

  I got an iPad 16 GB factory reset default after a while display only the power cord going to iTunes, need help to get this operational back, it worked Ok before resetting all we have tried to make clear the former owner information

  The iTunes icon and cable image means he went into recovery mode, you will need to connect it to iTunes to your computer to reset the iPad, and you can then restore/resync your content.

  If the previous owner had not disconnected from the settings > iCloud on it and find my iPad has been activated, you will need to communicate with him or her: disable find them my iPhone Activation Lock - Apple Support

• The power button will not turn on my computer. Is there a way to solve this problem, or the computer not sleep once I do back on?

  I have a MacBook Pro 2011.

  The power button does not turn the computer on when the computer goes to black screen.

  The battery he is

  iI tried to Community assistance to research and tried to wait. The next morning, I was able to turn it back on. Now, it happened again.

  Please help me. I can afford a new Mac.

  Thank you

  Get it fixed. Make an appointment at the Genius Bar in Apple for the service. If you need a Apple Store - find a store - Apple.

• My MacBook Pro with El Capitan 10.6.11 close the menu drop down. I have to turn off the power

  The closing down and options no longer work in El Capitan 10.6.11 restart on my MacBook Pro mid-2012. I have to press the power button to turn off.  When shutting down or restarting are selected, the Ribbon at the top of the screen disappears and Finder is no longer available but other aps on the bench of the accused are still available. When I restart after turning off the power, the system is back to normal until I need to close again.

  Hello

  Just in case, run disk utility.

  Open utility disk located in Applications/Utilities

  Then select the disk to boot on the left and then select the first aid tab and then click run.

  If disk utility indicates that the disc seems to be OK, you are finished. Otherwise, you must repair the disk.

• Another that holding down the power button, then by restarting, how should I manage my end 2009 27 "iMac when he crashes on the first blank white screen and won't start?

  Another holding down the power button, then by restarting, how should I handle turn on my end 2009 27 "iMac when he crashes on the first blank white screen and won't start?

  Combinations of keys start for Mac - Apple Support

• A Mac mini, purchased in the UNITED Arab Emirates can be used in the USA with only change the power cord?

  A Mac mini, purchased in the UNITED Arab Emirates can be used in the USA with only change the power cord?

  Yes.

  http://www.Apple.com/Mac-mini/specs/

  the voltage may vary from 100-240 V AC.

• Hi all, I bought apple phone I 5s recently is the power button / stop does not. Bought in the United States, but I was shifted to the India, the works of will to guarantee in India please help

  Hi all, I bought apple phone I 5s recently is the power button / stop does not. Bought in the United States, but I was shifted to the India, the works of will to guarantee in India please help

  Ask an authorized service provider regarding iPhones, a guarantee of a country may or may not be honored in another function where you take the device.

  (143868)

• Is there a way to the target url by using the power of Attorney (I want to say is possible to use the proxy to target a site something like that.)?

  Is there a way to the target url by using the power of Attorney (I want to say is possible to use the proxy to target a site something like that.)?

  By default, you can not in Firefox.

  But you can use an add-on like FoxyProxy Standard, I think he understands the functionality you need.