Troubleshooting couldn't identify the problem

Similar Questions

• Network Diagnostics Windows 7 cannot apply patches "unable to identify the problem.

  Hello. I'm running Windows 7 x 64; logged as administrator. Until recently have not had problems with the automated network diagnostics. Periodically, the Internet will stop working, and I click on "connection problem fixed." The system would not not automatic, including reset network cards and renew the IP addresses.

  Recently, this function has stopped working. Now, whenever I try to use Network Diagnostics, this utility ends with the message "Troubleshooting could not identify the problem."

  When I click on 'Further information', there is a message that "issues found: the adapter doesn't have a valid IP address" and the solution 'reset the adapter' is followed by ""DO NOT RUN " "

  If I create manually a problem such as disabling an adapter, it will give a similar indication that convenience store has been impossible to identify the problem. However, if I open the section more information, it shows that the adapter is disabled. with a solution 'Adapter to activate' that is NOT EXECUTED and nothing is done.

  I don't understand why this utility DOES NOT patch over. I looked for a setting activate for this and does. This problem appeared out of nowhere. It does not matter where I invoke diagnostics network - the result is the same.

  Thanks again for your time!

  Sincerely,

  David

  Hello

  Good to know that the problem is solved. Appreciate your efforts. Feel free to respond if you need help with Windows in the future, we will be happy to help you.

• Printer prints not; Unable to identify the problem of troubleshooting

  I have a HP OfficeJet 6500 (OS is Windows 7) on a wireless network that do not print. . Ran the Printing Troubleshooter, but it has been unable to identify the problem.

  Hello

  1. when it changes on the computer prior to this question?

  2. do you get an error message when you try to print?

  3. If so, what is the exact error code/message you get?

  Perform the following methods and check:

  Method 1: Run the fixit from following link and:

  Problems printing and printing errors

  Automatically diagnose and repair when you cannot print or for problems setting up a printer, connecting to a network printer and related errors.

  http://support.Microsoft.com/mats/printing_problems/

  Method 2:

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Let us know if it helps.

• I can't installed my AI of lightroom j recut in cd error message is "Advisor to identify the problem to support the following problem has been met the instalation n d programe has s could not initialize download Adobe" what I wanted to f

  I can't installed my AI of lightroom j recut the cd en error message is "Advisor to identify the problem to support the following problem has been met the instalation n d programe has s could not initialize download Adobe" what I wanted to do but this programe n exists more so know what to do?

  Please refer to the site link below and try the troubleshooting mentioned:

  https://forums.Adobe.com/thread/1848277

• HP color LaserJet 2550 PCL 6: If anyone can identify the problem of these prints?

  When I print, I get areas white, spots, lines, etc...

  If I print & printing becomes better & better until after 5-10 prints, it's perfect.

  I can print a few pages, then it will begin to fail again... but not as bad as when spends a lot of time and then try to print.

  I typically re - calibrate before printing, but I can't be sure if that is actually help.

  Here the 6 test pages, in order from the top left to bottom-right. It took 6 pages to get a good page.

  All the "ink" is full and there is no error msgs.

  Can someone identify the problem of these prints?   What piece of hardware is a failure.

  http://www.demonsdisks.com/pics/temp/HP-test-pages.jpg

  Thank you very much

  Your backup drum is bad.  Because the lines are now gone which confirms the first keg was bad and the new defect is caused by the backup.

• 1st step you should take to identify the problem

  Hi gurus

  I did my interview today and has confused the following question:

  Question Your query was working fine yesterday and today, when you try to run the same query, then it stuck, what would be the 1st step you should take to identify the problem?.

  My answer I checked the Plan to explain...

  but it seems that I gave the wrong answer.

  Any idea, what should be the 1st and other steps to identify and resolve the problem. Thank you

  Concerning

  Shu

  I did my interview today and has confused the following question:

  Question Your query was working fine yesterday and today, when you try to run the same query, then it stuck, what would be the 1st step you should take to identify the problem?.

  My answer I checked the Plan to explain...

  but it seems that I gave the wrong answer.

  Why it looks like you have the right answer?

  Any idea, what should be the 1st and other steps to identify and resolve the problem. Thank you

  Only the people interview you can say what response THEY were looking for and, for them, ONLY it would be the right answer.

  , You ask them what response they wanted? If not, why? It is an object of an interview - to see if someone is WILLING and ABLE to COMMUNICATE with you and he is not afraid to ask questions if they don't understand something.

  If you ask the poster what they were saying. If you did NOT request you missed them the perfect opportunity to get your question answered.

  When running a query today is different than it yesterday so SOMETHING has CHANGED.

  The FIRST step is to confirm that you really have a performance problem. In other words, to confirm that the request really is "stuck".

  The NEXT step is to determine what has changed between yesterday and today. There is a large data load? Are there more users of the NLE system?

• Setup failed to initialize. Download Adobe Support Advisor to identify the problem!

  Good evening

  I just redownload LR 6 LS11. But the initialization block with the message: "Setup could not initialize. Download Adobe Support Advisor to identify the problem. But this program is more supportati. How to unlock the boot?

  Thanks in advance!

  Please see the links below.

  • Error: "cannot install initialize | Windows
  • The Adobe CC Installer failed to initialize [windows OS]
  • I'm having trouble trying to install the trial cc version. The installation program is unable to initialize. Please help me
  • Creative cloud Installer fails to boot into OSX Mavericks

  Hope this will help you.

  Kind regards

  Hervé Khare

• Troubleshooting couldn't recognize the question

  I connected my mobile WiFi hotspot with my laptop now. The WiFi router is malfunctioning for the past days. I tried several times to troubleshooting, but the issue could not yet solved. The problem occurred when I clicked some link appeared when trying yo get tickets for matches coming baseball on the web. Now I'm stuck with my work and it has been 4 or 5 days. Does anyone know how to fix this? Can you recognize?

  Hello @adamTR

  Welcome to the community!

  Have what troubleshooting measures you tried?

  Did you try to do a factory reset and start over from scratch?

  See this article for more information about how to restore your connection.

• MS Vista startup repair couldn't fix the problem automatically

  Hello

  A little history - MS Vista was trying to install updates when the delivered system running. He failed. So I rebooted and it worked very well.

  When I re-started again after using it, even once, he tried to install updates. He failed. So I rebooted and it worked fine again. I went through the whole process several times in recent weeks.

  Then the other day, I got this screen start that says "Windows cannot repair this computer automatically. Since then, I can't get the computer started.

  The details of the problem are shown as:
  Problem event name: StartupRepairV2
  Signature of the problem 01: AutoFailover
  Signature of the problem 02: 6.0.6000.16386.6.0.6000.16386
  03:6 problem signature
  Signature of the 04:524296 problem
  Signature of the problem 05: CorruptFile
  Signature of the problem 06: CorruptFile
  Signature of the 07:3221225624 problem
  Signature problem 08:3
  Signature of the problem 09: WrpRepair
  Signature of the 10:10 problem
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033

  In addition, all tests have been completed successfully, with the same error code = 0x0

  First cause is to the states that "Startup Repair tried several times but still not determine the cause of the problem."

  If I have to re - install the operating system again... I was not given a CDROM as a HP laptop... How can I actually re - install, when I do not have the CDROM?

  Also, I have some very important folders on the hard drive and I want to recover the files first before reinstalling the operating system...

  Any advice on how I can get before I have to destroy it by reinstalling the operating system would be greatly appreciated.

  Thanks to you all.

  As you don't have a Vista DVD, try this:

  Download the ISO on the provided link and do a repair of the disc.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  For recovery disk/s and/or the use of the recovery Partition:

  http://h10025.www1.HP.com/ewfrf/wc/siteHome?lc=en&DLC=en&cc=au

  Online 24/7 support for home and individual HP products

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  You can also make recovery disk/s since the Partition of recovery in case of hard drive failure or System Crash, when you are in service again.

  They will tell you how to do this.

  Every computer manufacturer has their way of doing recovery disk/s.

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  Save all data, because it will be lost during a clean installation.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1 in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.

  Mick Murphy - Microsoft partner

• My form fields appear not on some operating systems, but are very good on most! Can anyone identify the problem?

  I have real problems with FF3.6.6 doesn't show is not some fields of text on a page. I run Windows XP with Mac 3.6.6 with 3.6.6 and a + 3.6.6 running virtual machine (with 2 s, Chrome, Safari, Opera), but it is fine for me but more and more people say that the fields are not there. The fields are a registration form which has been used for years in the address section. Can someone take a look to see if they can see all the fields here, or why the fields could not show in some cases. I do not spam you to look at the page, it's legitimate.

  Thank you very much

  If things with the announcement of the name don't work then the first suspect is always software blocking ads or extensions like Adblock Plus which can block content.

  I don't use of ABP, so can only test and it may always be a set of specific filter that is the cause.

• Try installing windows 10 with Windows 7 installed. Troubleshooter does not solve the problem

  Try installing windows 10 with Windows 7 installed. Troubleshooting Windows Update tool has not been set. Error code0x80070057 (2016 = 03-09-T - 08_11 - 14 p)

  Try to upgrade manually:

  Task of pre-required

  When you make significant changes to your computer for example updated operating system, you must always back up. See the links to resources on the backup by clicking the link for each version of Windows you are using: Windows XP, Windows Vista, Windows 7, Windows 8/8.1

  • How to back up and restore your files manually
  • How to free up disk space in Windows
  • How to: 10 tips before installing Windows 10
  • How to: determine if a device application or hardware is compatible with Windows 10
  • Will remain the documents and applications, or install app must

  then

  • How to download official Windows 10 ISO files
  • How to: upgrade previous versions of Windows using the file ISO for Windows 10

  then

  • Turn off (preferably uninstall) your Antivirus utility before you perform the upgrade.
  • Reboot several times, and then try again.
  • Disable the general USB peripherals (for example - smart card reader).
  • If you are using a SCSI drive, make sure you have the drivers available for your storage on a thumdrive device and it is connected. During the installation of Windows 10, click on the advanced custom Option and use the command load driver to load the driver for the SCSI drive. If this does not work and the installer still fails, consider switching to an IDE based hard drive.
  • Perform a clean boot, restart, and then try again.
  • If you upgrade to the. ISO file, disconnect from the Internet during the installation, if you are connected in LAN (Ethernet) or wireless, disable both, then try to install.
  • If you are updated through Windows Update, when download reaches 100% disconnect from the LAN (Ethernet) Internet or Wi - Fi, then proceed with the installation.
  • If this does not work, try using the. ISO file to upgrade if possible.
  • If you are connected to a domain, go to a local account.
  • If you have an external equipment, attached to the machine, unplug them (example, game controllers, USB sticks, external hard drive, printers, peripherals not essential).

• Impossible to solve the problem of Windows Vista Service Pack 2 update! (error code 80073712)

  original title: could not resolve the problem of Windows Vista Service Pack 2 update!

  Hey there,

  I got Windows Vista Home Premium Service Pack 1 in my laptop when I bought it. Recently there was no updates of security (e.g., KB2481109) to install it into my system with a error: 80073712 and I had received a notification from windows to install Windows Vista Service Pack 2update. I tried to install it from windows update, but I got the error: 8024200d. I read the solution on this site and followed by download the stand-alone file and install "System Update Readiness Tool" (KB947821). ". After that I downloaded the standalone version "Windows Vista Service Pack 2" (KB948465) and tried to install it, but I got the error: 800f081f. "» I did Scan SFC which there is "no question of integrity" in the system, uninstalled "Avira Antivirus software" and again tried to install Service Pack 2 , but again, I've got the error: 80073712 After all this I couldn't solve the problem. Please provide some tips if anyone has solved the same or has a solution!

  Thank you very much

  UD

  Hi Electrocuteud,

  You have access to a Windows Vista installation disc? If so, follow the steps in this document to perform an InPlace upgrade. This will reinstall Vista without making any changes to the files and programs on the computer. Even if your data and programs must be safe, it is always advisable to make sure that you have a recent backup before major changes on the computer.

• "Solve the problems of search and indexing" Windows Search directories

  When I try to search show no results. When I try to solve the problem and perform "Troubleshoot search and indexing", the problem is not resolved automatically and the following message appears: problem encountered incorrect permissions on the directories of Windows Search

  Hey Dalton,

  Deactivation and activation then Windows search of offers to activate Windows activate or disable can help resolve the issue.

  Perform the steps mentioned below and see if it helps.

  a: Type of Windows features turn on or off in the start search box and click on enter.

  b: uncheck Windows Search

  c: restart the computer.

  d: Type of Windows features turn on or off in the start search box and click on enter.

  e: Now activate Windows Search, and then restart the computer.

  f: Then click on Control Panel > Folder Options > view TAB > enable Show hidden folders files - Open C: (root drive) with windows Explorer - right click on the ProgramData folder > Security TAB > advanced > change permissions > check "replace all child object." > check if the user of the system, Admin, set to full control > Edit creator owner > check full control > close Edit > Apply > wait so 'YES' – and then click OK > OK

  g:  Now, check if the indexing works.

  Good day!

  Answer please if you face concerns.

• I need help for the problem event name: BlueScreen. Help, please...

  Problem event name: BlueScreen
  OS version: 6.1.7600.2.0.0.768.2
  Locale ID: 1033

  More information about the problem:
  BCCode: 116
  BCP1: FFFFFA8007D53010
  BCP2: FFFFF88006CEAC48
  BCP3: 0000000000000000
  BCP4: 0000000000000002
  OS version: 6_1_7600
  Service Pack: 0_0
  Product: 768_1

  Hi Vikram,

   

  Thanks for posting the question in the Microsoft Community!

  You get the blue screen error in the computer.

  To work with the issue, I suggest you to visit:

  Resolve stop (blue screen) error in Windows 7

  http://Windows.Microsoft.com/en-in/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  Note: When you restore the system to a previous state, programs and updates installed later will be deleted.

  Note: When checking a disk for errors, if bad sectors si des secteurs defectueux sont are found then the system tries to repair sector. All data may be lost. So make a backup of the data.

  Note: When you format a disk, all data will be lost.

   

  It would be useful for us to identify the problem, if you could upload the dump file.

  You can use the Sky-drive to download the dump file. Check the link for the steps on how to download Sky-Drive.

  http://social.technet.microsoft.com/Forums/en-US/w7itproui/thread/4fc10639-02db-4665-993a-08d865088d65.

  The location of the dump file is C:\Windows\Minidump\.

• Yet once the problem persists

  Hi friends,
  
  Three months before I configure e-mail in the apex and the mail was sent to apex as usual.
  
  But now it does not, as I couldn't guess the problem because there is none of the mails in the mail queue and it doesn't show any errors in the apex.
  
  But I don't know why im not receive emails.
  
  Since we set up our own smtp server and it is the address of the host of this 172.16.1.25 and I have also specified in the settings.l instance
  
  And we also use database 11g, we have activated the network as services.
  
  Then also, why im not receive emails, I don't know.
  
  It worked before, but it doesn't now. All that's missing here.
  
  Kind regards
  Mini

  Hey Mini,
  This message is typical of a server that is not reachable for any reason any.
  It might be that the smtp service is not running or it is not responding on the configured port or IP address (is it operational? it still works on the same IP? is there a firewall between the two? have you recently changed firewall rules?)

  Open the command line on the computer that runs the apex and try this

  Telnet port addr

  for example, I have a test of smtp server to 192.168.1.24 running on port 25 and my virtual servers apex I can perform this test to check if it is running:

  Telnet 192.168.1.24 25

  25 is the standard SMTP port.

  If it works, if opens a connection with the SMTP server, if not, will report you an error.

  Flavio

  ----
  http://oraclequirks.blogspot.com
  http://www.yocoya.com