Troubleshooting system error: 53 - path not found network

Similar Questions

• While making a stop to a vista computer remotely, an error "the path not found network" takes place.

  I'm stopping distance this computer running Windows Vista Homp Premium from a Windows XP Professional computer. I ran shutdown.exe, but it says "the network path is not found." The network is working properly and I can't do a ping to this computer. I made sure that I ran the closure of an administrator account that has the same cridentials as an administrator on vista computer account (when I changed it, I got "access denied"). Quite simply, I know I have the privileges necessary to perform a remote shutdown.

  I found the solution. He has been to change the LocalAccountsTokenFilterPolicy by following the instructions here: http://support.microsoft.com/kb/942817

• When I use the Client for NFS provided by Windows 7, I'm unable to connect. The "mount \\ip address\share Z:" command fails with the error code "the path not found network".

  Identification of customer's Windows 7 NFS UID GID information

  I am trying to connect to the Windows 7 Client NFS on a server running on a computer (VxWorks) NFS.  I am able to properly connect Client NFS software by a 3rd party on the NFS server.  However, when I use the Client for NFS provided by Windows 7, I am unable to connect.  The \\ip address\share Z: mount"command fails with the error code"the path not found network ".  I can't do a ping of the computer running the NFS server.

  The NFS Client operating system: Windows 7 Ultimate, 64-bit

  Data captured by Wireshark

  MOUNT V1 EXPORT call 3rd party client
  Identification information Flavor: AUTH_UNIX (1)
  Length: 32
  Stamp: 0xc7065970

  Machine name: PC
  UID: 1000
  GID: 1000

  MOUNT V1 EXPORT appeal of the NFS client
  Identification information Flavor: AUTH_NULL (0)
  Length: 0

  It seems that the credentials of NFS Client are not correct.  How can I change the flavor of AUTH_UNIX and the UID and GID to 1000?

  Hello VDAEMP,

  As Eddie and Sudarshan has said, the Microsoft Answers community focuses on issues and problems related to the consumer environment. Please join the public IT pro TechNet forums below:
  TechNet - Windows Server
   
  Thank you

• Linksys - router bridge - E8350 path not found network

  Dear community of Linksys,

  I recently bought a Linksys E8350 router, to replace the old AP in my network domestic.

  To make the installer of my clear network, I did a little diagram:

  

  So, as you can see, at the top left is the router/modem provided by my internet provider (Telenet, Belgium).

  I have a wired connection in my room, where I have my desktop and NAS connected computer. I also plugged the

  Linksys E8350 that is configured in Bridge mode. My laptop is connected wireless to the E8350.

  On the E8350, I disabled DHCP and NAT and gave him a static IP outside the range of my other router.

  My problem:

  When I go to the network through windows file Explorer, I can see my desktop from my laptop and vice versa.

  But when I double click to access one of them, I get the error message "network path not found".

  Connection via start > \\Computer-name gives the same error.

  Since my laptop or my desktop, I can see my NAS on the network. I have internet on all my devices:

  My office through internet cable connection, my laptop has wireless internet connection trough

  and I can evaluate my NAS from the internet.

  When I remove the E8350 entirely from my network and connect my laptop a hollow wired connection.

  everything works fine. I can see all the devices on the network, connect to my NAS and share files between computers.

  Things I tried already:

  -My PC and laptop are both in a 'private network '.

  -J' disabled my firewall

  -Everything is activated in the menu "sharing advanced settings."

  -J' tried to connect the E8350 to the switch via the Ethernet or WLAN port, nor to solve the problem

  -J' tried to change the NETBIOS settings

  -I don't have your antivirus software that might interfere with something

  -J' updated the firmware on my linksys router to the latest version

  To be clear, the problem occurs when I put the E8350 in my network, otherwise everything works perfectly.

  I hope that I have provided some information decent on my problem, because I can't seem to figure it out myself.

  Thank you in advance.

  Pindox

  The topology of your network is effective from your diagram. With the E8350 in mode bridge in this topology is WAN is connected to the network switch.

  Many devices of bridge no hand NetBios address very well. In some cases, the best way to access the network through a bridge device resources is to use remote devices IP address instead of its computer\device network name.

  In Windows, you can drive old school card NAS records using the IP address of the Servers\NAS:

  PC command line:

  NET use s: \\192.168.0.3\my_nas_folder / persistent: Yes

• Lsass.exe system error object name not found, unable to start Windows in any mode.

  I am working on a friends computer who has a problem, it does not boot in any mode.  This includes everything and all alternate Mode without failure, last known good Configuration and other options in between.

  The computer is an old one but running Windows XP with Service Pack 3 and is updated from a few months ago.  He had a program to update AVG as well as several anti-spyware installed SpyBot, Adaware, and Malwarebytes programs.  Sometimes, the computer had a virus or spyware that was eventually deleted by the user with these programs in the past.

  I searched the internet for at least 8-10 hours looking for solutions without real success.  If not all of you with this problem, most eventually do a full reformat their hard drive.  This owner does not have a recovery disk (lost?) with their computer for that and they have important documents that they would be saved.  A solution (last resort) is to remove the hard drive and put it in my computer to copy documents on a cd/dvd.  It is very likely to buy a newer computer at this stage anyway, but needs these documents

  -----------------

  What happens is after the start screen of Windows, but before the Welcome screen, a box with the lsass.exe system error error: object name not found appears.  Clicking on it just restarts the computer to restart the process.

  I used a boot Norton cd to test the virus in case it might be this worm Sasser, sometimes associated with this error and it is clean. so I really doubt that this problem is associated with that.  Also used checks and drive to scan to check for errors.  Don't check, there is no way to go back to a previous restore point or configuration.

  Tried to use the recovery console out of my Windows XP installation disk: in this case I tried to develop a copy of the file lsass.exe on the hard drive, but it could not extend the file.  I tried several times with the same results.  Don't really know if that would have helped it worked.

  At this point, I'm really at a loss on how to continue.  Any suggestion would be appreciated and thanks in advance!

  Your friend's computer is not likely to be infected by the Sasser worm that this virus is many, many years now. Extract the data on the drive and do a clean install/factory restore of Windows. You can usually buy the mftr computer recovery media. (if an OEM brand like HP, Dell, etc.). low-cost. If you decide to reinstall Windows, test the material first to make sure it's healthy. Or skip reinstallation if your friend is going to buy a new computer and just take the data for him.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot
  http://michaelstevenstech.com/cleanxpinstall.html - Clean install - how-to
  http://www.elephantboycomputers.com/page2.html#Reinstalling_Windows - what you will need at hand

  1 remove the drive and put it in a box of USB drive or use a USB adapter. Attach it to a computer that is running a working XP/Vista/Windows7 installation. Use the work of Windows Explorer to copy the data to the hard drive of the system to the rescue and burn data on cd or dvd, or copy it to an external hard drive. I prefer not to do it if I know the drive is infected because he has a chance to infect your host system. In these cases, I use #2 below.

  2. you can start the computer target with a Bart PE (XP only) or Linux Livecd such as Knoppix or Ubuntu and retrieve the data in this way. This has the additional advantage to tell you if the problems you are experiencing are hardware or software related because if the computer behaves perfectly in Linux, you know that Windows (software) is the culprit. Conversely, if the computer behaves badly under Linux, you will know that there is a hardware problem. This is general information on the use of Knoppix for the recovery of data when you do not have Windows:

  You will need a computer with two cd records, one of which is an engraver of CD/DVD OR a USB thumb drive with enough capacity to contain your data OR an external USB hard drive. Download Knoppix .iso image file and create your bootable CD *. If you do this in a previous (XP or Vista) operating system, you will need the third burning like Nero, Roxio or freeImgBurn software (Windows 7 can burn .isos natively). Burn as an image, not in the form of data. Then boot with the CD that you created and the Windows files will be visible under Linux. If you want to burn CD/DVD, there will be a Linux burning program to use.

  * If your computer has only an optical drive and you want to use this drive to burn data or need to test drive, you can create a USB bootable Linux instead of a bootable CD. This site will show you how to do it-http://www.pendrivelinux.com

  http://www.Knoppix.NET
  http://www.nu2.nu/pebuilder/ - Bart PE Builder

  See also - http://lifehacker.com/5504531/the-complete-guide-to-saving-your-windows-system-with-a-thumb-drive
  And for future disaster recovery programs - http://www.elephantboycomputers.com/page2.html#Backing_Up

  MS - MVP - Elephant Boy computers - don't panic!

• path not found network when joining the domain

  I am using windows server 2008 r2 when I join the area win 7 & 8 pro his show network path was not found, but in xp it works

  Hi Pradeep,

  Thanks for posting your query in Microsoft Community.

  The problem you are having is more complex than what is generally answered in the Microsoft Answers forums. It would be more appropriate to redirect your request to scientists on TechNet Forums that are well equipped with knowledge on this issues.

  You can click on the link below to send your query in technet forum.

  http://social.technet.Microsoft.com/forums/en-us/w8itpronetworking/threads

  I hope it will give you the help you need. Please do not hesitate to contact Microsoft Community for Windows related queries

• To connect to a shared folder between PC - error Code 0 x 80070035 "network path not found."

  I have a client with 8 computers on a workgroup network.

  Among youth, 2 computers not talking to each other or to connect to shared folders on the other drive. Both computers will speak on other computers on the network (wireless).

  I looked at all the solutions that have been validated for the message Error Code 0 x 80070035 "network path not found." and none of them have solved the problem. I can't ping one computer to another. I noticed that when troubleshooting on the PC (both are desktop windows 7), 'client' that when I ping the other PC it returns an IPV4 (192.168.x.x) address, but when I ping another PC on the network returns an IPV6 address. I tried to turn off IPV6 adapter in the network adapter settings. It made no difference. I searched several 6to4 adapters in Device Manager, but only 1 exists. Turn it off did not seem to make a difference. As I said, both PC's are accessible by other computers on the network (wireless), but they cannot access each other.

  Restart both computers several times (including cold starts and stops).

  The only one I don't have not tried yet is releasing and renewing the IP address on both.

  Any suggestions?

  Well I fixed it myself.

  In this case, there was a number of things I've done.

  First of all, I checked to make sure that the firewall is not the issue. It wasn't.

  Secondly, I checked the network connection to see if it has been set to the office network. One of them was, and that we have tried to connect to a was created for the Public network. Who changed the network and restarted.

  Who has not solved the problem.

  Finally, in desperation more than any other thing, I restart the network modem.

  Guess what? That fixed the problem.

  So, I guess it was a problem of ARP table or some other problem. When I tried to ping from the "client PC' on the shared drive PC, the IP address was 192.168.1.65. When I got the customer go to the drive shared PC and check the IP address it is 192.168.1.69.

  Restart the modem and the "client PC" has solved the problem.

• Cannot connect Windows 7 to the field get error network path not found.

  Title: original network path not found

  I have a professional Windows 7 Desktop and Windows Server 2008 Standard server.  When I try to connect my desktop computer to the domain, I receicve an error "the network not found path.  I tried almost all of the solutions found for the search for this error without result.  How can I locate the source of this error and fix it?

  Hi ECBender,

  Thanks for posting the question in the Microsoft Community!

  You cannot connect to a domain and the message that the network path was not found.

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the Forum TechNet site:

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  I hope this helps. If you need additional help, let us know and we would be happy to help you.

• Home network problem: 0 x 80070035: network path not found.

  I have problems with my home network; my laptop is unable to access the files on my HTPC

  More precisely:

  Laptops and PCs are running Windows 7 Ultimate. My laptop is connected to the home wireless network, the PC is connected through the LAN. Router is a Netgear DG834GV. Both computers have fixed IP addresses. They are part of the standard workgroup workgroup. There was formerly a group residential, put in place, which worked very well. We also have a Vista laptop that does all the unusual problems. Until a few days ago, the whole Setup worked perfectly. I could previously access/copy/distribute multimedia content, play on the PC via Zune music on my laptop and print from my laptop to the computer, but now I am unable to do one of these. The other laptop still works fine.
  From the network on the PC screen, I can see the files from the laptop and access.

  However, since the network on the computer screen laptop, I see the PC, but when I try to open it I get the error "Windows could not access \\MEDIACENTER. 0 x 80070035 the network path was not found. "I ping the PC with the IP address and name, and I can even remote to the computer desktop.

  ipconfig on the laptop did something funny...

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Card tunnel Local Area Connection * 139:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Card tunnel Local Area Connection * 143:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  Card tunnel Local Area Connection * 140:

  ... up to 200. I can't that assume it goes back to #1 as well.

  After a few suggestions on here I just went through the enable netbios over TCP/IP, but now I can't see even the PC! Still can ping and access internet tho.

  Any suggestions as to what may be the cause?

  Here is the solution for "error code 0 x 80070035 network path not found" on Windows Vista and Windows 7 computers. Click on the button 'START', select 'CONTROL PANEL' and go to 'DEVICE MANAGER'. Click on "NETWORK CARDS", then click on 'VIEW' and select 'SHOW HIDDEN DEVICES'. In the expanded view, you will see a long list of numbered "MICROSOFT 6to4 ADAPTER". My Windows 7 Professional Office had 200 of them. Right click and select 'DELETE' on all but 1 of them. You can only do 1 at a time, so it takes some time. When you have only 1 left, restart the computer and enjoy being able to see the other computers on your network, including the RESIDENTIAL group files.

• C$(\\192.168.1.253 networks) (O :) network path not found.

  Using a new dell with windows 7 - I get a message: Mircosoft windows network: network path not found.

  Network location (1) C$(\\192.168.1.253) (o) what does that mean?

  It's a path mapped to a share.

  Click Start > computer > you should see this path under 'Computer' > right click on this share > select disconnect

  Reboot and see if the message reappears.

  I hope this helps.

• ERROR: NetExpress 5.0 install path not found - WOOF SDK 4.1

  I was finally able to install the SDK with your help, but now I'm looking at another problem.
  
  In the installation document, after the addition of Eclipse it says:
  Start Eclipse by opening the directory of the SDK Oracle Client utility Scripts
  (Start? All programs? Oracle Utilities 4.0.0.x Software Development Kit? Oracle Utilities
  Scripts Client Software Development Kit) and by double clicking on startEclipse.bat. x is the
  Build number.
  •
  This launches Eclipse with the Welcome tab.
  
  When I run the .bat file, I get the following error:
  ERROR: NetExpress 5.0 path not found... on line 52 of C:\OUAFSDK\SDK\4.0.0.5\Scripts\bin\getBinDirectory.pl.
  
  Nowhere in the install doc it says nothing on NetExpress.
  
  Any ideas?
  
  Thank you.

  It is available on e-delivery in the same place in which you downloaded the framework and other applications.

• Scheduler BI - error "path not found".

  People,
  
  I am trying to edit 'My account' to set devices in 'My products'-> book.
  I could note the health empty error message and not able to create any kind of device.
  
  ******************************************************************
  Mount errors
  
  Path not found (/ users/admin/_prefs/instruments/e-mail)
  Error details
  Error codes: U9KP7Q94
  ******************************************************************
  
  Please let me know where things could've gone wrong.
  
  Thanks in advance!
  
  Cecilia.

  You must manually create.

• Could not initialize the TestStand engine. Path not found.

  Hi, so far I have installed and removed TestStand 3.5 3 times in a row, just to still get this message (see subject) when I try to start the sequence editor. I even uninstalled all the software of NOR I had on this laptop reinstall the whole... Nothing has worked. Now I wonder, is that what I'm doing wrong? What can I do to get TestStand running?

  Well well, on this message when I hit OK, another message

  The sequence editor does not start. Cannot create the TestStand engine.

  Hit OK on that message again just puts an end to the sequence editor leaving me with a white screen.

  Any ideas what is wrong?

  best regards and thanks in advance.,

  Ingo

  Ingo-

  Sorry for your frustration. Your idea to uninstall and reinstall should work normally. The second message is just the result of the first error, so we need to understand which path is not found, and we don't know why this happens. I tried to force my copy of TestStand 3.5 to fail like messing around with the installation and I couldn't find a way to cause the error "path not found". I had a lot of other more detailed errors, but I have been unable to reproduce your message.

  A few questions:

  (1) what operating system do you use?

  (2) you install to the default location under Program Files? You use a network somehow path?

  (3) you have permission to write the locations on your system?

  (4) what are you logged in as long as administrator during the installation, reboot and start the sequence editor.

  (5) have you messed with any of the registry under HKEY_LOCAL_MACHINE\SOFTWARE\National Instruments\TestStand\3.5 settings, where something is wrong manually?

  (6) added user under the TestStand directory components that could somehow load and cause a problem?

  If you have an installation on the system, you can quickly try to empty the directory Cfg under TestStand, so that it generates new copies of these files.

• The page you are looking for is not available. You may need to contact your administrator with this error: 404 Page not found.

  I am at a loss.  I've set up a root certification authority to sign all servers in my workspace of Horizon, SAML is in the Green and after a lot of reading when troubleshooting also synchronized on all my ESXi hosts and guests.

  Basically, what I did is the following:

  Set up the connection to the Server VMware View Horizon 5.2 - created different pools and can connect via the customer different platform. (a few times to eliminate any possible configuration errors along the way)

  Configuration of VMware View Horizon Workspace 1.0 (a few times now) with self-signed and CA signed certs.  My workspace appears fine, the synchronization of files, apps work, and view pools appear.  When I try to launch your desktop from inside the Horizon workspace I get this error:

  The page you are looking for is not available. You may need to contact your administrator with this error: 404 Page not found.

  Now I think that I followed it down to something to do with SAML connection - which, to my understanding, archery chips between workspace and view.  On the login server, I see it in the Windows event log:

  BROKER_USER_AUTHFAILED_SAML_ACCESS_REQUIRED

  SAML access required but not tempted by customer

  Attributes:

  Source = com. VMware.VDI.Broker.filters.SamlAuthFilter

  Time = MON may 20 16:06:41 MDT 2013

  Gravity = AUDIT_FAIL

  Node = ViewConnection.access360.ca

  Module = broker

  Recognized = true

  Something is not crossing to allow me to access my office view since the workspace of Horizon.  If I remove the requirement of SAML on the login server see, when I try to connect to a desktop computer from the view connection server I get a promotion for and can I get my IDs & field and have full access with reviews, as well as blast HTML - just cannot get there with Horizon Workspace.  There must be something that I am missing with SAML...

  As I said, I'm at a loss here on what does not work between the Horizon workspace and the connection of SAML for display to connect to the server.  There is no server security, server transfer, and firewalls is all off, so I don't think it's a network problem.  Simple as possible.  The Windows Journal event displays the login displays server error is: access required but not attempted by client SAML.  I have all my servers synchronized after a few seconds - so I don't think that documented the TIME Horizon workspace synchronization time sensitivity is responsible here.  I am Pack overnight, but will do exactly the same thing with a client of tomorrow - hopefully without the same result!

  Any ideas?

  A

  So I re-deployed the VAPP (again!) very attentive as I went.  As usual, the initial database installation failed because I entered my domain FULL of the gateway name, so it does not match.  After useful messages already there for this (Workspace install fails with error creating the user admin) I used the wizardssl.hzn of connfigurator - going to recreate a rootca to the environment based on my FULL domain instead of the bridge - going and then let it grow all for the other vApps.  I then connected to each and pulled down my private rootca and ran c_rehash, etc. (another useful message!- adding MS signed Certs to Horizon Workspace & laquo;) Carlos & #039; Corner) I actually use my background to UNIX and openssl to be my own private CA and sign all of my certificates.  I created the SAN cert and added to the SSL configuration on the Configurator - going and connector - going.  Oddly enough, both of these server do not appear to be accepting SAN cert that includes their ENTIRE domain, but that's for another day... My Horizon Workspace FQDN does show as being approved by installed RootCA private (which does not have other DNS names for the service - going, the Configurator - goes, the data - will and the connector - will, but as I have already said--a battle for another day) so it's a good thing.  I joined my workspace to my domain name - well!  Activated would be pools seen in the Configurator - goes - sync - good.  CRT for the my display login server has accepted and implemented the SAML trust.  Still good.  Sync in my opinion users group who already had a couple of linked clone pools allowed to do.  Good.  Connected to the FQDN of my workspace and clicked on computers - seen my 3 pools.  Clicked on one and after a few seconds, launched in a new window of the explosion.  Success!  I disconnected and connected on a different machine, and something that I saw before, but doesn't have a lot of attention to was the connector - will put 'use windows authentication', I couldn't understand why every time I sailed on my Horizon workspace a no vmware window opens asking access my FQDN:443 with a user and pass.  It is this setting - duh.  I'm not sure yet that gives me, so it's off for now.

  Thanks for all the input: it's good to know that there are others with some of the same questions.  It's still v1.0, it is related to some of these pitfalls.  It is capricious with derived from same time less than 10 seconds seems to have a negative impact.  Had to ensure my ESXi servers were strong (never worried a lot in the past with MS AD being quite tolerant with small derivatives) I tired my vApps affecting a NTP, but they seemed like being left to the default of synchronization to the ESXi host.  See how than pans.  CERT is somewhat capricious depending on your deployment.  Of course the connector - will and the Configurator - must be signed by a CA that they are internal, but always be nice to then have signed internal...

  Now, I'm on ThinApps for desktops as well as the web interface integration.

  I bumped my head against the wall with my first configuration of Citrix XA and XD (before having VDI in a box!) and it was the best way to learn.

  I don't know that I grave along that I finished my PoC, but I'm very happy with today's results.  I still plan on the comparison of my logs successful with the logs I have pulled my former deployment TIME and see what it was that it was broken.  I think it was that wanted me a PTR record to my domain FULL DNS MS. name  I think I just had the direct search for the original bridge - will and FULL, but only a setback for the gateway domain - name.  Would explain why I was never able to connect to the gateway to access your desktop.  Oops.

  A

• Preview in browser - HTTP Error 404.0 - not found

  I installed xampp on a computer network in order to set up a php mysql Web site.

  Using dreamweaver on my local machine, I've implemented the new site. Please see below...

  (The folders below are on the C drive network - not my local machine)

  local root folder: "xampp\htdocs\mysite."

  file of the test server: "xampp\htdocs\mysite."

  Prefix of the URL : http://localhost/mysite

  When I try to preview in the browser, I get this error message:

  HTTP Error 404.0 - not found

  The resource you are looking for has been removed, had its name changed, or is temporarily unavailable.

  Detailed error information

  Module	IIS Web Core
  Notification	MapRequestHandler
  Handler	StaticFile
  Error code	0 x 80070002

  Requested URL	http://localhost:80/mysite/info.php
  Physical path	C:\inetpub\wwwroot\mysite\info.php
  Logon method	Anonymous
  User logon	Anonymous

  For me, it looks like he's trying to find the file "info.php" on my local computer when it is in fact on a computer on the network.

  I opened a session on the computer on the network using desktop connection remote to test the info.php file in Internet Explorer and it works very well.

  So, how can I solve this problem for me to "Preview in browser" on the network? Can it be done?

  Thank you

  Wookie says:

  I installed xampp on a computer network in order to set up a php mysql Web site.

  Using dreamweaver on my local machine, I've implemented the new site. Please see below...

  (The folders below are on the C drive network - not my local machine)

  local root folder: "xampp\htdocs\mysite."

  file of the test server: "xampp\htdocs\mysite."

  Prefix of the URL : http://localhost/mysite

  Localhost is an alias for the IP loopback address used by each computer to identify itself. If these files are on drive C of the computer on your network, you must use the IP address of the computer on the network, instead of localhost. Other information you give shows that the computer tries to find localhost on your own computer running IIS, not of XAMPP.