Try to write data to the file, but error 200279

Similar Questions

• write table 2D data in the file but the file is empty

  Hello

  I tried to write all reading of powermeter data to a file in two ways, I can see the output in the Arrais indicator data but when I write to "File.vi of the worksheet" or write to 'text file', the files are empty.

  Please help me.

  Try to remove the vi "STOP".

  I suspect, it prevents the main vi before the backup occurs.

  As a second point: given that you save data inside a while loop be sure you add the data from the file and not crash each time.

  wire that is a 'real' terminal 'Add file '.

  Kind regards

  Marco

• Data from the file server error

  Hi, I used the following steps to create a server for FILE data
  
  To create a server for file data:
  1. connect to the topology Manager
  2. Select the topology > physical Architecture > Technologies > file in the tree of
  3 right-click and select Insert data server
  4 fill in the following fields in the Definition tab:
  • Name: the name of the database server will appear in Oracle Data Integrator
  • Username/password: not used.
  5. complete the following fields in the JDBC tab, depending on the driver used:
  • JDBC Driver: com.sunopsis.jdbc.driver.file.FileDriver
  • URL JDBC: jdbc:snps:dbfile
  6. click on Test
  7. click on Test in the Test connection window
  
  But I get an error
  
  http://img30.imageshack.us/img30/5173/test3i.jpg
  
  Can you please tell me what I'm missing. I'm new to ODI

  Hello

  Its just typo error, you mentioned here properly properly as com.sunopsis.jdbc.driver.file.FileDriver jdbc driver

  but looking carefully at the image file, you send, you talked the driver files, wrongly, that you are missing the word 'pilot' in your jdbc driver.

  Correct it and it will work.

• Best way to record 50 kech. / s data to the file

  I'm reading a data acquisition data at a sample rate of 50 kech. / s and save it in a file. My application must run for at least a few hours. At first, I tried a model of loop of consumer-producer with a writing on measurement file Express VI, but he wrote the data too slowly, and my queue. Now, I'm trying to use the Write to VI file spreadsheet with or without a loop of producer-consumer model (see attached screws). Both seem to write data to the file, but no written records the number of datapoints I expect (the two have a lot less datapoints).

  What is the best way to write data to the file? Seems like a basic question, so if it has already been discussed in detail in another forum, or if there are examples of what someone could point me to, that would be appreciated also.

  Thank you!

  Hvea look at "stream directly to disk with TDMS in LabVIEW".

• How can I write snapshot of my data to the file measured every 5 seconds

  Hello

  I try to take a snapshot of my stream once every 5 seconds and write it to a. File LVM. I have problems with the VI "write to a measurement file. The pace at which it writes data to the file seems to be dictated by the 'Samples to Read' parameter in the DAQ assistant. I tried placing the VI 'Write in a file measure' within a business structure and the launch of the structure to deal with a "time up" VI. As a result only in a delay of 5 seconds before the insiders 'Write in a file as' VI. Once the VI 'Write in a file as' is launched, it starts writing at 20 x per second. Is there a way to change it or dictate how fast the exicutes VI 'Write in a file measure'?

  My reason for slowing down the write speed are, 1) reduce space occupied by my data file. (2) reduce the cycles of CPU use and disk access.

  The reason why I can't increase the value of 'Samples to Read' in the DAQ Assistant (to match my requirement to write data), it's that my VI will start to Miss events and triggers.

  I don't know I can't be the only person who needs high-frequency data acquisition and low-frequency writing data on the disk? However, I see a straight road to key in before that.

  The equipment I use is a NI USB DAQ 6008, data acquisition analog voltage to 100 Hz.

  Thanks in advance for your help

  See you soon

  Kim

  Dohhh!

  The re - set feature has not been put in time elapsed VI!

  Thank you very much!

  See you soon

  Kim

• DASYLab how to write data to a file every 15 minutes

  Hi all

  I use dasylab and datashuttle/3000 to record data. What I want to do is to write data to a file every 15 minutes. I use the milti-file, which can write data to the file diffenret, but how do I control the timing, as the journal data every 15 minutes automatically.

  The other problem is that I use FFT analysis of the frequency spectrum. How can I determine the value of frequency where the peaks that happens.

  Thank you

  Write less data in the file that you have collected requires the reduction of certain data.

  There are three techniques to consider.

  With an average or an average of block - both reduce the data by using a function of averaging, defined in the module. To accomplish the reduction of data, choose block or RHM mode in the dialog box properties, and then enter the number of samples/data values that you want to reach on average.

  Average - when you reduce the data, you also should reblock data using the block length of the change in the output parameter. For example if you enjoy at 100 samples/second with a block size of 64, the average module configured on average, more than 10 samples will take 10 times longer to fill a block. The initial block represent 0.64 seconds, the output block represent 6.4 seconds at a sampling rate of 10 samples/second. If you change the size of output in one block, the program remains sensitive.

  Average block - average values in a block against each subsequent block, where the average is based position. The first samples are averaged, all second samples are average... etc. The output is a block of data, where each position has been averaged over the previous blocks. This is how you will be an average data FFT or histogram, for example, because the x-axis has been transformed in Hz or bins.

  Second technique - separate module. This allows to reduce the data and the effective sampling rate jumping blocks or samples. For example, to reduce the data in 1000 samples / second to 100 samples per second, configure the module to keep a sample, jumping 9, keep one, jumping 9, etc. If you configure to skip blocks, you will not reduce the sampling frequency, but will reduce the overall amount of data in a single block 9, for example. It is appropriate for the FFT data or histogram, for example, to have the context of the correct data.

  Finally, you can use a relay and a synchronization module module to control. For example, to reduce a sample data every 15 seconds, configure a generator module of TTL pulses for a cycle of 15 seconds of time. Connect it to a Combi trigger module and configure it to trigger on rising and stop the outbreak directly, with a trigger value after 1. The trigger output connects to the X of the relay command input.

  In addition to these techniques, you can change the third technique to allow a variable duration using a combination of other modules.

  Many of these techniques are covered in the help-tutorial-Quickstart, as the data reduction is one of the most frequently asked questions.

  In regards to the FFT... use the module of statistical values in order to obtain the Maximum and the Max Position. The Position of Max will be the value of the frequency associated with the Maximum value. The output of the statistics module is a single sample per block. Look at the different FFT sample installed in the worksheet calculation/examples folder.

• Access to the data in the file permissions

  I have a html file that is generated by a third-party application.
  I want to give only the permissions to write data in the file, I don't want to give permissions to remove content.
  (it's not the file's content in the file)
  How can I put it please suggest me.

  As I said...  I don't think that what you want is possible.
  If someone can write (Edit) a file, then it can also remove all the contents of this file.

  It seems to me that you are looking for a software revision control... something that helps other people to make changes to a [copy of a] set of files, but gives a control authority the word to say as to when and if changes go in the direct copy.  It also regression to an earlier point in time.

  "Comparison of revision control software.
   <>http://en.Wikipedia.org/wiki/Comparison_of_revision_control_software >

  HTH,
  JW

• Satellite P500/01R reads the data, but cannot write data on CD files

  I recently bought a laptop Satellite P500/01R. I am able to read a data CD, but can't write data on CD files. The CD is read/write.

  Any ideas?

  Hello

  Have you tried different burning software?
  I m using Nero and in my opinion one of the apps better combustion.
  Here, I can choose between CD, DVD, DL or Blueray (only possible if the CD/DVD drive also supports this).

  Have you also checked diffΘrents CDs from different manufacturers?
  You should do this since not all disks are 100% compatible.
  I had several problems with different CD or DVD in most of the cases it was a compatibility issue, I tried TDK and this kind of drive is compatible with my CD/DVD drive
  I m using the standard of R.

• Write data to text file generates the error

  Hi all

  I need to write data to a file using TestStand and I configired the entrance and outside like below, but I get the error message like ' an error occurred 'Write' calling in 'ITextStream' of 'Microsoft Scripting Runtime' [error Code:-2146828234].

  I followed the same procedure for reading text that works very well for me.

  Hope others might have faced the problem / or I do something wrong.

  Do what is necessary.

  

  Found problem while opening a file I used IO Mode ForReading instead of ForWriting.

  Unnecessarily the thread created, but then hope this can help someone later when they deal with a particular issue.

• fwrite error: try to write 26 bytes of file and the problems

  I'm writing 26 Hex bytes data file using fwrite and I have unknown problems because of which has written 27 bytes

  /////////////////////////////////// Code ///////////////////////////////////////////////////////////////////
  FILE * READ;
  READ = fopen ("DataReceived.dat", 'w'); opening the file for writing

  unsigned char data2send [26] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00};
          
  data2send [0] = 0xEB; conferment of the data
          
  data2send [1] = 0 x 90; conferment of the data

  data2send [10] = 0x08; / / data assignment
           
  crcsent = calCRC16 (data2send, 24); calculation of 24 bytes CRC and the addition of crc (16 bit) to last two bytes of data
          
  data2send [24] =(crcsent>>8) & 0xFF; Added to the second last octet CRC
          
  data2send [25] = (crcsent & 0xFF);   CRC has added up to the last byte
         
  If (ComWrt (coms, data2send, 26) == 26) / / send data to com port
  {
               
  fwrite (data2send, 1, 26, READ); ===> writing data in the file where there is problem
      
  }
  /////////////////////////////////////////////////////////////////////////////////////////////////////////////

  Production (WRITTEN in the file) should be:

  0xEB 0 X 90 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x08 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0 x 00 0x0A 0xA1

  Output that I get the file (which is incorrect) and do not do because I've specified 26 bytes to write

  0xEB 0 x 90 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x08 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0 x 00 0x0D 0x0A 0xA1

  How 0x0D is added to my data, even though I'm only add data Byte 0,1,10,24,25

  When I write 26 bytes then how 27 bytes are written to the file?

  Thanks in advance

  arfaoui

  I can only imagine that the problem may arise from opening the file in text mode and write on it (0x0A) a line break character: the system can automatically add a CR (0x0D) in order to maintain the standard CRLF. Try opening the file in binary mode instead (fopen with "wb" specification).

• Write delay failed unable to save all the data for the file $Mft

  Have a frustrating problem.  Help is greatly appreciated.  Learned the hard way and lost a dwg important issue which was unrecoverable.  Bought a new drive external hard seagate.  Could not back up the entire system with software pre-installed.  Download acronis true image home 2011.  Tried to backup system.  Receive error when trying to backup messages; 'Delay to failure of Scripture; Reading of the sector; Windows was unable to save all the data for the file $Mft. The data has been lost.  Have tried many fixes.  Unable to disable write caching method (grayed out / unclickable).  Played regedit 'EnableOplocks' is not listed to select.  Attempted to run microsoft 'fix it' and got the blue screen of death.  Short hair out of my head.  Suggestions appreciated.

  I don't know where Microsoft 'Technical support engineers' get their information.

  Write caching without a doubt "does apply to external hard drives", but it is usually disabled to prevent to sort the problem you are experiencing.

  I've seen several positions reporting to the same question that you do.  All of these positions were with SATA drives.  Is your Seagate eSATA drive?

  The disc is recognized as an external drive in Device Manager?  In Device Manager, go to the drive properties dialog box and click the policies tab.  An external drive should have two options: "Optimize for quick removal" and "Optimize for performance".  An internal hard drive shows the options as gray (with 'performance' selected), but there should also be a checkbox "Enable disk write cache" under the second option.

  What shows in your policies tab?

  If I understand correctly, "writeback" or "write behind" is implemented by disc material or its pilot.  If the option is not available on the drive properties > policies tab, I would suggest to contact Seagate support.

• When you try to copy a. DAT in Vista file, get error 0x80070057L, the parameter is incorrect

  I tried to copy a *. DAT file from a CD on my HARD drive. During the last 5 seconds, I always get the following error message:

  Error 0x80070057L the parameter is incorrect

  I am able to open the file, but can not copy. I tried on my laptop (Vista SP1) and on an another desktop running XP and get the same error.

  What causes this problem?

  Hello

  The problem occurs when you try to copy other files?

  Check if you can copy files in Mode without failure.

  Refer to this article for help:
  http://Windows.Microsoft.com/en-CA/Windows7/start-your-computer-in-safe-mode

  Kind regards
  Afzal Taher
  Microsoft technical support engineer

• When we try to write in a pdf file. document, it changes the Danish letters Æ Ø Å to different signs. To do this, this om pc and Mac. Anyone know of a solution? Thank you

  When we try to write in a pdf file. document, it changes the Danish letters Æ Ø Å to different signs. To do this, this om pc and Mac. Anyone know of a solution? Thank you

  Hi, I found the problem, it seems that the pdf file uses a helvetica font, and when we write in a part of the PDF with the Danish letters A, Æ, O, it changes signs. I changed the Roman fonts in adobe acrobat pro, and then there's no problem. But he seem´s that the standard in pdf files is helvetica, and there is not time to change the files, because we get only the files on the day of the exams at school. It happens in all versions of adobe 11 and DC, it is also a problem on Windows 7, 8.1 and windows 10 more Macbook.

  Kind regards

  Med Hotel hilsen

  Price Patrick Simon

  TI-Vejleder

  Langeskov Skole

  Ronningevej 38

  Langeskov 5550

  Denmark

  FRA: meenakshin83966505 [email protected]<>[email protected]>

  SVAR til: "[email protected]<>[email protected]> ' [email protected]<>[email protected]>" "

  Dato: måndag den 18. January 2016 kl. 14.39

  Til: Simon Price [email protected]<>[email protected]>

  Emne: You have been mentioned by meenakshin83966505 in Re: when we try to write in a pdf file. document, it changes the Danish letters Æ Ø Å to different signs. To do this, this om pc and Mac. Anyone know of a solution? Thanks to the Adobe community

  You talked

  by meenakshin83966505https://forums.adobe.com/people/meenakshin83966505?et=notification.mention> in Re: when we try to write in a pdf file. document, it changes the Danish letters Æ Ø Å to different signs. To do this, this om pc and Mac. Anyone know of a solution? Thanks to Adobe Community - see the reference from meenakshin83966505 to youhttps://forums.adobe.com/message/8402116?et=notification.mention#8402116>

• Error message on Windows XP, "Windows-Delayed Write failed, windows was unable to save all the data for the file.

  I use windows xp as the operating system. I bought the new 3G huawei data card. While surfing internet, between a pop-up is displayed

  «Windows-delayed write failed, windows was unable to save all data in the file C:\Documents and settings\new\Local Settings\Application Data\Google\Chrome\User Data\Default\Session Storage\004285.log.» The data has been lost. This error can be caused by a failure of your computer hardware.

  After this computer freezes and I have to restart my computer. Please help me how to fix this problem.

  The error basically says that he tried to write something on your hard drive and for some reason that unfinished write operation.  This could indicate a bad sector on your hard disk, damaged disk or a problem with your hardware.

  Whenever a problem involving a disk read or write appears, my first approach is to perform a verify operation of the disc to the hard drive.  Even if this is not your problem, it is a step of good routine maintenance. Run the disk check with the "/ R" or "Repair" option.  Note that the real disk check will be presented at the next reboot, will run until Windows loads completely, cannot be interrupted and can take more than a few hours to run depending on the size of your hard drive, the quantity and type found corruption and other factors.   It is better to perform during the night or when you won't need your computer for several hours.

  'How to perform disk in Windows XP error Cherking'

  <>http://support.Microsoft.com/kb/315265/en-us >

  HTH,

  JW

• The lateset, 2015.5 edition, does not transfer data from the metadata, only the focal length objective. Disappointment when you want to know what that lens you used. (It allows to rename the files but after you create a second copy. "It's an improvement.)

  The last edition, 2015.5, does not transfer data from the metadata, only the focal length objective. Disappointment when you want to know what that lens you used. (It allows to rename the files but after you create a second copy. "It's an improvement.)

  Yes, copied files from Nikon NEF, DNG.