Trying to access a scanner on the network

Similar Questions

• 'PC' is not set up to establish a connection on port "file and printer sharing (SMB)" with this computer - I get this after enabling access to public folders and then trying to access (another pc on the network cannot connect to this pc but see).

  • Tried to reconfigure the firewall
  • Tried to change files and printers, sharing options
  • Restarted other computers trying to connect to my public folder
  • Tried to adjust the network discovery
  • Do all computers on the network among the same workgroup
  • I can access public folders from the other computer and their content
  • Other computers on my network, in my workgroup can see my public folders, and users, but cannot access it.
  • Other computers can see my computer, but can not access: error code: 0 x 80070035.

  Can't access: 'Public' and 'Users' in the title:

  -Network
  MyName-PC

  Please don't give me that: "If you try to connect to another computer, make sure that this computer is on, that you have enabled file and printer sharing on both computers, and file and printer sharing can communicate through your firewall." Because I seek NOT to connect to another computer... I want to just access MY Public folder and the users folder and eventually allow others to access also.

  Hi Katmandu774,

   

  Welcome to Microsoft Answers Forums.

  The Public folder is a convenient way to share files that are stored on your computer. You can share files in this folder with other people using the same computer and with people using other computers on the same network. Any file or folder you put in the folder Public is automatically shared with the people who have access to your Public folder.

  If you are not on a domain, you can limit network access to the Public folder so that people with a user account and password for this computer. To do this, turn on sharing protected by password.

  1. Open the network and sharing Center by clicking the Start button, clicking Control Panel, click network and Internet, click network and sharing Center.
  2. Click the arrow next to password protected sharing, and then click one of the following options:

  ·         Turn on password protected sharing

  ·         Turn off password protected sharing

  1. Click apply. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  To control the level of access to the Public folder

   

  1. Open the network and sharing Center by clicking the Start button, clicking Control Panel, click network and Internet, click network and sharing Center.
  2. Click the arrow next to public folder sharing, and then click one of the following options:

  ·         Turn on sharing so anyone with network access can open files

  ·         Turn on sharing so anyone with network access can open, change and create files

  ·         Turn off sharing (people logged on to this computer can still access this folder)

  1. Click apply. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  Also, make sure you add everyone to the public folder and give the necessary permissions to access it.

  Sharing files with the Public folder

  http://Windows.Microsoft.com/en-us/Windows-Vista/sharing-files-with-the-public-folder

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Migrated domain users are needed to access shared folders on the network with AD username old or need to share with the new AD ID

  Dear Sir

  Migrated domain users are needed to access shared folders on the network with AD username old or need to share with the new AD ID

  I am in a field & I'll migrate with a domain name.

  EX: now I'm in the field of the AAA tomorrow my domain name will change to BBB. User accounts are created in two AAA & BBB and the two domain user IDs are different.

  data servers are also migrating with the new domain.

  is it possible to access share with the old user id folder in new field or both to share the files again with the new user ID Active directory.

  Kind regards

  Chauvet J.

  Hello

  The question you have posted is related to professional level support. Please visit the below mentioned link to find a community that will support what ask you:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• Error when trying to access an item in the repository through the VAC

  Hello

  I tried to access an item in the repository of the ACC, I receive the following error message:

  Error reading the list index or a table of the database. , This means the database table holding that this property has sequential whole not starting with 0 in multiple columns. This only happens if the database table has been modified directly (outside of Dynamo).

  java.lang.Exception

  at atg.adapter.gsa.ListTable.loadHelper(ListTable.java:190)

  at atg.adapter.gsa.ListTable.loadProperties(ListTable.java:97)

  at atg.adapter.gsa.GSAItemDescriptor.loadProperties(GSAItemDescriptor.java:5874)

  at atg.adapter.gsa.GSAItemDescriptor.loadProperty(GSAItemDescriptor.java:5986)

  at atg.adapter.gsa.GSAItem.getPersistentPropertyValue(GSAItem.java:1339)

  at atg.adapter.gsa.GSAItem.getPropertyValue(GSAItem.java:1232)

  at atg.adapter.gsa.GSAItem.getPropertyValue(GSAItem.java:1510)

  at atg.repository.RepositoryItemImpl.getPropertyValue(RepositoryItemImpl.java:151)

  at atg.repository.nucleus.RepositoryItemPropertyMapper.getPropertyValue(RepositoryItemPropertyMapper.java:151)

  at atg.beans.DynamicBeans.getPropertyValue(DynamicBeans.java:333)

  at atg.beans.DynamicBeanState.initializeFrom(DynamicBeanState.java:152)

  to atg.beans.DynamicBeanState. < init > (DynamicBeanState.java:122)

  to atg.ui.repository.model.RepositoryItemState. < init > (RepositoryItemState.java:428)

  at atg.ui.repository.model.RepositoryAgentImpl.createRepositoryItemState(RepositoryAgentImpl.java:2934)

  at atg.ui.repository.model.RepositoryAgentImpl.getRepositoryItem(RepositoryAgentImpl.java:3901)

  at atg.ui.repository.model.RepositoryAgentImpl.getRepositoryItem(RepositoryAgentImpl.java:1225)

  at atg.ui.repository.model.RepositoryAgentImpl.getCompressedRepositoryItem(RepositoryAgentImpl.java:1251)

  at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)

  at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)

  at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)

  at java.lang.reflect.Method.invoke(Method.java:597)

  to atg.security.proxy.UserSessionProxy$ SessionSkeletonHandler.invoke (UserSessionProxy.java:273)

  at atg.rmi.context.ContextualSkeletonImpl.invoke(ContextualSkeletonImpl.java:127)

  at sun.reflect.GeneratedMethodAccessor401.invoke (unknown Source)

  at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)

  at java.lang.reflect.Method.invoke(Method.java:597)

  at sun.rmi.server.UnicastServerRef.dispatch(UnicastServerRef.java:303)

  to sun.rmi.transport.Transport$ 1.run(Transport.java:159)

  at java.security.AccessController.doPrivileged (Native Method)

  at sun.rmi.transport.Transport.serviceCall(Transport.java:155)

  at sun.rmi.transport.tcp.TCPTransport.handleMessages(TCPTransport.java:535)

  to sun.rmi.transport.tcp.TCPTransport$ ConnectionHandler.run0 (TCPTransport.java:790)

  to sun.rmi.transport.tcp.TCPTransport$ ConnectionHandler.run (TCPTransport.java:649)

  to java.util.concurrent.ThreadPoolExecutor$ Worker.runTask (ThreadPoolExecutor.java:895)

  to java.util.concurrent.ThreadPoolExecutor$ Worker.run (ThreadPoolExecutor.java:918)

  at java.lang.Thread.run(Thread.java:662)

  Corrected data type for a property change in the definition file.

• How to access multiple VMs on the network with nic 1 host?

  Greetings,

  I have a server vmware running windows XP with 3 virtual machines in suse. I would like to access the 3 virtual machines from the network at the same time. The vm 3 has their own static ip address. I use the bridge network mode. There is only 1 NETWORK card on the XP computer. With this configuration, I can access only 1 vm the network at a time. When I added an another NIC and jumpered it on a second computer, virtual, then I can access 2 at the same time.  Any ideas on how I can access all the vm 3 at the same time on the network with just 1 NETWORK card?

  Even if you only have a physical NETWORK adapter, you should be able to access all the guests at the same time when they use bridged networking and have a correct IP configuration. Can you put your host IP configuration and your guests so we can check it out. Make sure the guests are really "bridged" and disable all firewall during the test.

  If you found this information useful, please consider awarding points to 'Correct' or 'Useful' answers and answers. Thank you!!

• I try to do the Task Scheduler open an Access 2007 DB on the network

  Hello

  Any help with this one?

  I have a DB of 2007 access on a shared folder on the network.  I want 4 users to be able to start and DB that open when they are connected.

  It works when you schedule the execution of a program that is located on the local disk, for example, open Notepad or a other prog.

  When I do the following...

  Create the new task (no base)

  Open task DB name > run when the user logged on (they must be in any case) use with the highest privileges = yes > Configure to Vista or server 2008 (using Small Business SERVER 2003 and Vista Bus)

  Relaxation > in the journal to start GOLD > specific user or group (ME) check box selected = Yes

  Action > start a program > Browse to the program/script = x player database - name.accdb

  Conditions - no defined (of course supply sector)

  Settings > allow the task runs at the request - stop after three days (again, I'm not that long!)

  Click RUN to see if it works. Nothing happens

  All suggestions, anyione has done something similar?

  Tried several variations on the settings, still no joy.

  Thanks in advance. McP

  You can get help by creating a new post on the forums TechNet here: http://social.technet.microsoft.com/Forums/en-US/itprovistaact/threads

• Error "you don't have permission to access \\Mike-PC\c. Contact your network administrator to request access." When you try to access a computer on the network

  Original title:

  There are three computers in my office. Both run Windows 7 Edition Home Premium and the third is running Windows 7 Professional.
  I am trying to allow access to files on the computers of Home Premium. I go to 'Network' and open the other computer, but he said "You are not allowed access. \\Mike-PC\c contact your network administrator to request access." I went to Mike-PC computer to 'Share' this folder then joined the homegroup even / working group and everything in 'Advanced sharing' in the 'network and sharing Center', but it does still not activated.

  The Professional Windows 7 computer successfully ' "shared folders and the other two computers can read / write files, but not the other way around.

  Any help would be greatly appreciated.

  Hello

  1 are these computers using a homegroup or working group?

  2. were you able to share files earlier?

  3 have had it all changes to computers, before the show?

  Method 1:

  Refer to the suggestion provided by Jack MVP on January 25, 2011, in the following link.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/you-do-not-have-permission-to-access-pcname/baa06630-4d3d-4ba2-837a-b087bd21cdb3

  Method 2:

  Disable the firewall and security software and check.

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off

  Note: Runs the computer without antivirus software or firewall is a potential threat to the computer; don't forget to activate the security software after completing the troubleshooting steps and after you have identified the problem.

• Error code 651 while trying to connect my computer to the network

  * Original title: Please help

  I am trying to connect my computer to work at our network and when I try to connect to our broadband network he said WAN mini port connection and then it gives me an error code 651.  Does anyone have a suggestion?

  You are probably connected through the bad device.  You must have a wireless to laptop (?).  If so,.

  Control Panel

  Network and Internet

  Network Sharing Center

  Change the settings for the adapter.

  Make sure that the network adapter to use is selected

  Right-click on it and select Connect

• Problems with NAT? Can't access internet from inside the network?

  I was intrigued with this problem for a few days now. I'm stuck on what could be the issue. The problem is that I can ping my router, G0/0 and G0/1, to the internet. However, since the switch and my PC, I can not ping Internet. I'm sure that everything is configured correctly, but here is my setup for the switch and the router:

  Router 1:

  version 15.1 no service button horodateurs service debug datetime msec Log service timestamps datetime msec encryption password service ! hostname LAN_Router_1 ! boot-start-marker boot-end-marker ! ! enable secret 5 *. ! No aaa new-model ! no location network-clock-participate 3 ! dot11 syslog no ip source route ! IP cef ! ! ! ! domain IP MyTestLab.com 8.8.8.8 IP name-server IP-server names 8.8.4.4 No ipv6 cef ! Authenticated MultiLink bundle-name Panel ! ! ! ! ! voice-card 0 ! ! ! ! ! ! ! Crypto pki token removal timeout default 0 ! ! ! ! license udi pid CISCO3845-MB sn FOC105013BA username * secret privilege 15 5 *. ! redundancy ! ! property intellectual ssh time 60 property intellectual ssh authentication-2 retries property intellectual ssh event logging property intellectual ssh version 2 ! ! ! ! ! ! ! ! interface Loopback0 192.168.254.1 IP 255.255.255.255 ! interface GigabitEthernet0/0 DHCP IP address penetration of the IP stream stream IP output NAT outside IP IP virtual-reassembly in automatic duplex automatic speed media type rj45 ! interface GigabitEthernet0/1 the IP 192.168.0.1 255.255.255.248 penetration of the IP stream stream IP output IP nat inside IP virtual-reassembly in GLBP 100 ip 192.168.0.4 priority GLBP 100 115 GLBP 100 preempt automatic duplex automatic speed media type rj45 ! ospf Router 5 router ID - 192.168.254.1 network 192.168.0.1 0.0.0.0 area 1 192.168.254.1 network 0.0.0.0 area 0 ! IP forward-Protocol ND no ip address of the http server no ip http secure server ! ! IP nat inside source list 10 interface GigabitEthernet0/0 overload IP route 0.0.0.0 0.0.0.0 dhcp ! access-list 10 permit 192.168.94.32 0.0.0.15 connect access-list 10 permit 192.168.17.0 connect 0.0.0.7 access-list 10 permit 192.168.52.0 connect 0.0.0.7

  
  access-list 10 permit 192.168.0.0 0.0.0.7 connect
  access-list 10 deny any newspaper
  !
  !
  !
  !
  !
  !
  control plan
  !
  !
  !
  !

  profile MGCP default
  !
  !
  !
  !
  !
  connection of the banner ^ C
  W A R N I N G

  THIS IS A PRIVATE COMPUTER SYSTEM.

  This computer system, including all related equipment, network devices
  (specifically including Internet access), are provided only for
  authorized used.

  All computer systems may be monitored for all lawful, including purpose
  to ensure that their use is authorized, for management of the system, to
  facilitate protection against unauthorized access, and to verify security
  survival and operational security procedures.

  Monitoring includes active attacks by authorized personnel and their
  entities to test or verify the security of the system. During the surveillance,.
  information may be examined, recorded, copied and used for authorized
  purposes.

  All information, including personal information, placed on or sent over
  This system may be monitored. Uses of this system, authorized or
  unauthorized, constitutes consent to monitoring of this system.

  Unauthorized use may subject you to criminal prosecution. Evidence of
  any unauthorized use collected during monitoring may be used for
  administrative, criminal or other adverse action. Use of this system
  constitutes a consent to monitoring for these purposes.
  ^ C
  !
  Line con 0
  Synchronous recording
  local connection
  line to 0
  line vty 0
  local connection
  entry ssh transport
  output transport ssh
  line vty 1 4
  opening of session
  transport of entry all
  !
  Scheduler allocate 20000 1000
  NTP 198.60.73.8 Server
  NTP 13.85.70.43 Server
  SaveRunConfig event manager applet
  cron cron-event timer entry ' 0 0 * * ".
  command action 1.0 cli 'enable '.
  cli 2.0 action command "RAM".

  Router 2:

  version 15.1 horodateurs service debug datetime msec Log service timestamps datetime msec encryption password service ! hostname LAN_Router_2 ! boot-start-marker boot-end-marker ! ! ! card order type necessary for slot 1 Monitor logging warnings enable secret 5 *. ! No aaa new-model ! clock timezone CST - 5 0 ! dot11 syslog IP source-route ! IP cef ! ! ! ! domain IP MyTestLab.com 8.8.8.8 IP name-server IP-server names 8.8.4.4 No ipv6 cef ! Authenticated MultiLink bundle-name Panel ! ! ! ! type of parameter-card inspect global Select a dropped packet newspapers ! voice-card 0 ! ! ! ! !

  
  !
  !
  Crypto pki token removal timeout default 0
  !
  !
  !
  !
  license udi pid CISCO3845-MB sn FOC1411592J
  username * secret 5 *.

  !
  redundancy
  !
  !
  property intellectual ssh time 60
  property intellectual ssh authentication-2 retries
  property intellectual ssh event logging
  property intellectual ssh version 2
  !
  !
  !
  !
  !
  !
  !
  !
  interface Loopback0
  192.168.254.2 the IP 255.255.255.255
  !
  interface GigabitEthernet0/0
  DHCP IP address
  penetration of the IP stream
  stream IP output
  NAT outside IP
  IP virtual-reassembly in
  automatic duplex
  automatic speed
  media type rj45
  !
  interface GigabitEthernet0/1
  IP 192.168.0.2 255.255.255.248
  penetration of the IP stream
  stream IP output
  IP nat inside
  IP virtual-reassembly in
  GLBP 100 ip 192.168.0.4
  priority GLBP 100 110
  automatic duplex
  automatic speed
  media type rj45
  !
  ospf Router 5
  router ID - 192.168.254.2
  network 192.168.0.2 0.0.0.0 area 1
  0.0.0.0 network 192.168.254.2 area 0
  !
  Default IP gateway 192.168.0.1
  IP forward-Protocol ND
  no ip address of the http server
  no ip http secure server
  !
  !
  IP nat inside source list 10 interface GigabitEthernet0/0 overload
  IP route 0.0.0.0 0.0.0.0 dhcp
  !
  SSH extended IP access list
  permit tcp host 192.168.52.2 any eq 22 log
  permit tcp 192.168.10.0 0.0.0.255 any eq 22 log
  permit tcp host 192.168.17.18 any eq 22 log
  any eq 22 host tcp 192.168.0.1 newspaper permit
  permit tcp host 192.168.0.2 any eq 22 log
  permit tcp host 192.168.0.3 any eq 22 log
  permit tcp host 192.168.0.5 any eq 22 log
  denyip a session
  !
  access-list 10 permit 192.168.94.32 0.0.0.15 connect
  access-list 10 permit 192.168.17.0 connect 0.0.0.7
  access-list 10 permit 192.168.52.0 connect 0.0.0.7
  access-list 10 permit 192.168.0.0 0.0.0.7 connect
  access-list 10 deny any newspaper
  !
  !
  !
  !
  !
  !
  control plan
  !
  !
  !
  !
  profile MGCP default
  !
  !
  !
  !
  !
  connection of the banner ^ C
  W A R N I N G

  THIS IS A PRIVATE COMPUTER SYSTEM.

  This computer system, including all related equipment, network devices
  (specifically including Internet access), are provided only for
  authorized used.

  All computer systems may be monitored for all lawful, including purpose
  to ensure that their use is authorized, for management of the system, to
  facilitate protection against unauthorized access, and to verify security
  survival and operational security procedures.

  Monitoring includes active attacks by authorized personnel and their
  entities to test or verify the security of the system. During the surveillance,.
  information may be examined, recorded, copied and used for authorized
  purposes.

  All information, including personal information, placed on or sent over
  This system may be monitored. Uses of this system, authorized or
  unauthorized, constitutes consent to monitoring of this system.

  Unauthorized use may subject you to criminal prosecution. Evidence of
  any unauthorized use collected during monitoring may be used for
  administrative, criminal or other adverse action. Use of this system
  constitutes a consent to monitoring for these purposes.
  ^ C
  !
  Line con 0
  session-timeout 360
  exec-timeout 360 0
  7 password *.
  Synchronous recording
  local connection
  line to 0
  opening of session
  line vty 0 4
  SSH access class in
  Synchronous recording
  local connection
  entry ssh transport
  output transport ssh
  !
  Scheduler allocate 20000 1000
  NTP 198.60.73.8 Server
  NTP 13.85.70.43 Server
  SaveRunConfig event manager applet
  cron cron-event timer entry ' 0 0 * * ".
  command action 1.0 cli 'enable '.
  cli 2.0 action command "RAM".

  Switch:

  version 12.2 no service button tcp KeepAlive-component snap-in service a tcp-KeepAlive-quick service horodateurs service debug uptime Log service timestamps uptime encryption password service ! hostname LAN_Switch ! boot-start-marker boot-end-marker ! ! username * secret privilege 15 5 *. ! ! ! No aaa new-model clock timezone CST - 6 1 supply ws-c3750-24ts switch mtu 1500 routing system IP routing IP - domain name MyTestLab.com 8.8.8.8 IP name-server IP-server names 8.8.4.4 ! ! ! ! ! ! ! ! ! spanning tree mode rapid pvst spanning tree logging spanning tree extend id-system ! internal allocation policy of VLAN ascendant ! property intellectual ssh time 60 property intellectual ssh authentication-2 retries property intellectual ssh event logging property intellectual ssh version 2 ! ! interface Loopback0 192.168.254.5 the IP 255.255.255.255 ! interface FastEthernet1/0/1 switchport access vlan 17 switchport mode access spanning tree portfast spanning tree enable bpduguard ! interface FastEthernet1/0/2 switchport access vlan 10 switchport mode access spanning tree portfast spanning tree enable bpduguard ! interface FastEthernet1/0/3 switchport access vlan 666 switchport mode access Shutdown spanning tree portfast spanning tree enable bpduguard ! interface FastEthernet1/0/4 switchport access vlan 666 switchport mode access Shutdown spanning tree portfast spanning tree enable bpduguard

  
  !
  interface FastEthernet1/0/5
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/6
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/7
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/8
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/9
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/10
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/11
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/12
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/13
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/14
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/15
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/16
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/17
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/18
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/19
  Description # PC #.
  switchport access vlan 10
  switchport mode access
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/20
  Description # X_BOX #.
  switchport access vlan 666
  switchport mode access
  Shutdown
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/21
  switchport access vlan 94
  switchport mode access
  spanning tree portfast
  spanning tree enable bpduguard
  !
  interface FastEthernet1/0/22
  switchport access vlan 5
  switchport mode access
  !
  interface FastEthernet1/0/23
  switchport access vlan 5
  switchport mode access
  !
  interface FastEthernet1/0/24
  switchport access vlan 5
  switchport mode access
  !
  GigabitEthernet1/0/1 interface
  switchport access vlan 666
  Shutdown
  !
  interface GigabitEthernet1/0/2
  switchport access vlan 666
  Shutdown
  !
  interface Vlan1
  no ip address
  Shutdown
  !
  interface Vlan5
  IP 192.168.0.5 255.255.255.248
  !
  interface Vlan10
  address 192.168.10.2 255.255.255.0
  !
  interface Vlan17
  IP 192.168.17.17 255.255.255.248
  !
  interface Vlan52
  IP 192.168.52.1 255.255.255.248
  !
  interface Vlan94
  IP 192.168.94.33 255.255.255.240
  !
  ospf Router 5
  router ID - 192.168.254.5
  Log-adjacency-changes
  network 192.168.0.5 0.0.0.0 area 1
  network 192.168.10.2 0.0.0.0 area 2
  network 192.168.17.17 0.0.0.0 area 2
  network 192.168.52.1 0.0.0.0 area 2
  network 192.168.94.33 0.0.0.0 area 2
  0.0.0.0 network 192.168.254.5 area 0
  !
  IP classless
  IP route 0.0.0.0 0.0.0.0 192.168.0.4 permanent
  no ip address of the http server
  no ip http secure server
  !
  !
  SSH_IN extended IP access list
  permit tcp host 192.168.52.2 any eq 22 log
  permit tcp 192.168.10.0 0.0.0.255 any eq 22 log
  permit tcp host 192.168.17.18 any eq 22 log
  any eq 22 host tcp 192.168.0.1 newspaper permit
  permit tcp host 192.168.0.2 any eq 22 log
  permit tcp host 192.168.0.3 any eq 22 log
  permit tcp host 192.168.0.5 any eq 22 log
  deny ip any any newspaper
  !
  !
  connection of the banner ^ C
  W A R N I N G
  THIS IS A PRIVATE COMPUTER SYSTEM.
  This computer system, including all related equipment, network devices
  (specifically including Internet access), are provided only for
  authorized used.
  All computer systems may be monitored for all lawful, including purpose
  to ensure that their use is authorized, for management of the system, to
  facilitate protection against unauthorized access, and to verify security
  survival and operational security procedures.
  Monitoring includes active attacks by authorized personnel and their
  entities to test or verify the security of the system. During the surveillance,.
  information may be examined, recorded, copied and used for authorized
  purposes.
  All information, including personal information, placed on or sent over
  This system may be monitored. Uses of this system, authorized or
  unauthorized, constitutes consent to monitoring of this system.
  Unauthorized use may subject you to criminal prosecution. Evidence of
  any unauthorized use collected during monitoring may be used for
  administrative, criminal or other adverse action. Use of this system
  constitutes a consent to monitoring for these purposes.
  ^ C
  !
  Line con 0
  session-timeout 60
  exec-timeout 60 0
  Synchronous recording
  local connection
  line vty 0
  access-class SSH_IN in
  local connection
  line vty 1 4
  access-class SSH_IN in
  opening of session
  line vty 5 15
  access-class SSH_IN in
  opening of session
  !
  NTP 198.60.73.8 Server
  Event Manager environment suspend_ports_config flash: / susp_ports.dat
  Event Manager environment suspend_ports_days 7
  Event Manager user Directorystrategie "flash: / policies /.
  Event manager session cli username "stw".
  political event manager sl_suspend_ports.tcl
  political event manager tm_suspend_ports.tcl
  SaveRunConfig event manager applet
  cron cron-event timer entry ' 0 0 * * ".
  command action 1.0 cli 'enable '.
  cli 2.0 action command "RAM".

  Well, I totally forgot the keyword "log" and NAT:

  Cisco IOS NAT support ACLs with a keyword "log"?

  A. When you configure Cisco IOS NAT translation dynamic NAT, an ACL is used to identify the packages that can be translated. The current NAT architecture does not support the ACL with a keyword "log".

  http://www.Cisco.com/c/en/us/support/docs/IP/network-address-translation...

  If your problem is not the mask with joker, but the command "log"...

• I'm trying to access all sites gives the warning (error code: sec_error_unknown_issuer)

  This affects my computer only profile (windows 8) and only on Firefox. I disabled SSL on AVG as help pages suggest and tried to reinstall, both without effect. Someone knows how to fix this?

  Check the date and time and time zone in clock of your computer: (double) click on the clock icon in the Windows taskbar.

  Find out why the site is not approved, then click on "Technical Details" to expand this section.
  If the certificate is not reliable because no issuer channel was provided (sec_error_unknown_issuer) and then see if you can install the intermediate certificate from another source.

  You can retrieve the certificate and check details such as WHO issued the certificates and the expiration dates of certificates.

  • Click on the link at the bottom of the error page: "I understand the risks".

  Let Firefox recover the certificate: "Add Exception"-> "get certificate".

  • Click on the "view..." button. "and inspect the certificate and the Coachman, who is the issuer of the certificate.

  You can see more details like the intermediate certificates that are used in the details pane.

  If "I understand the risks" is missing, then this page can be opened in a (i) frame and in this case, try the shortcut menu and use "Frame this: Open image in New Tab".

  • Note that some firewall monitors connections (sure) and that programs like Sendori or FiddlerRoot can intercept connections and send their own certificate instead of the certificate of the Web site.
  • Note that it is not recommended to add a permanent exception in such a case, so only use it to inspect the certificate.

• Trying to access local resources in the RDS, the resources of the user session only 1 shows

  I'm developing an application to be able to copy files to the local drive of the user to a RD.  I Remote Desktop of the user defined options to put their C: drives the RD session on two remote computers.  When I connect the server from a remote computer, I can see his drive C: in the left pane of Windows Explorer.  When I connect with each other, however, the C: drive of the computer is not indicated, and I can't access it.

  My application will have multiple simultaneous users, most of the time, and some of the programs need to return data to their respective local computers.  Is there something I'm missing, or there at - it another way to do this programmatically or by command line Copy?

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Remote Desktop Services forum. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en-us/winserverTS/threads

• Module is trying to access a secure API - the reinstallation of Signature keys...

  Hello

  ATER, a problem that I have to reinstall my eclipse + jde plugin, as a result of this relocation, I also need to ask new .csi file in order to resinstall also Signature keys.

  After receiving 3 new csi files, signature keys has been successfully installed.

  Now, I have no problem when I run a ' build and sign Blackberry Widget Project ", that I get every time that a" SUCCESS BUILDING "result.»

  The problem is when I execute the widget on a real device, after the launch of the application whenever I get a "Module to access a secure API attempts" then the request has failed.

  Feature: Storm 2 9529 worm 5.0.0.306 (platform)

  For your information before my new installtion of the eclipse + JDE widget built with previous keys and the previous eclipse running on the same device that above.

  I did not change my source code, I try just to check if the application still running with the new keys and the new Eclipse + JDE.

  Does anyone have an idea what's wrong?

  Looks like you need another set of files of csi.

  Before installing your new keys delete all files sigtool.csk, sigtool.db and sigtool.set on your PC.  This will clear your previous code signing keys.

  So be sure to install each of the 3 csi files in the mansion even to make sure that all are installed in the same development tool.

• Looking for user/passwd name access f4500 info via the network

  Hello

  I have a Deskjet f4500 connected via Wifi. When I connect to the printer via a browser by specifying the IP address, I get a nice graphic information page (ink levels, networking, etc...)

  On this page, there are 2 other thumbnails 'Settings' and 'Networking '. When I click on these thumbnails, I get a popup window indicating that the site "printer HP Networking @" requires a user name and a password.

  I have not find the name of user/passwd anywhere in the hp docs and web.

  The problem is the same unser Windows or Linux.

  Can you help me?

  Thank you

  Didier

  Hello

  This is news to me - I'll have to remember that.

  Best wishes

  DP - K

• trying to access a database on the test server msaccess

  Hi, wonder if anyone can help me.

  I have been tring to connect to a database access on my ftp site wiothout any chance. The file is stored on the server and every time I try to make a connection to the base I get the same error, via a DNS or a connection string.

  the error is as follows.

  HTTP 404 File not found error code

  possible reasons

  1. There is no server running on the machine testingf

  2 test specified for this site server is not mapped with the Http://mywebsite/httpdocs/_mmServerScripts/MMHTTPDB.asp URL . Make sure that the URL prefix is the root of the site.

  (("If I download an .asp page < % Response.write(Server.MapPath("/mydatabase.mdb ")) % >, when you click the page returns;D:\inetpub\vhosts\mywebsite\httpdocs\mydatabases.mdb as well prove that the server executes scripts ASP. It does not view real-time data, return the above error. did the same with a time responswrite and works the same, good loading on the server, but does not not or the link to dreamweaver cs3.

  Any ideas would be grateful, my ISP has helped me all they can, but yet they do not know why I can't get the connection works.

  all the best, Mark

  > I have been tring to connect to a database access on my ftp site wiothout any chance

  I assume you are talking about web server that you can not connect to access via FTP

  Check your paths for your test server in site manager.

• I am trying to open my folder on the network.

  

  But I get this.

  You must have missed certain permissions.  On the computer KRYCH, right click on the folder and choose Properties.  Then go to the Security tab and check that it is allowed for all.  Also check the tab of sharing for the share permissions, which are similar but distinct.