TSM 1012 & cDAQ 9133

Similar Questions

• cDAQ 9133 12 "MONITOR WHITE

  cDAQ 9133 race built into windows 7 and a monitor 12 "NOR connected to monitor port is empty after coming out of sleep mode. cDAQ 9133 State seeing a flashing yellow, press reset button, indicator light turns off, monitor indicates reboot and then turns off. OR 12 "monitor power LED blinks green. Press the button has no effect. Monitor remains blank. Must be able to cDAQ turned off, and then to restart windows and monitor to display normally.

  Currently, there is no update of the BIOS for the cDAQ-9133.

  The timer that is documented in the section of the Menu system of the TSM-101 x Series manual is a little misleading: it means actually how long the screen display remains visible after the last button an is pressed.  As you found with your test during the night, monitor screen saver and standby modes depend on the display of the operating system configuration.

  The behavior you have described - the impossibility of recovering the display when power off monitor and turn it back on - is a known issue that is currently under review.  For now, the recommended solution is to configure the display to be always active, just as you did.

• XNET Signal list control deployed to target RT OR-cDAQ-9133

  I develop a VI to read and record the signals from the engine CAN. One of the requirements is that it will be a stand-alone application which runs on the target device, a device of real-time OR-cDAQ-9133 with a module NI9861. It also has a module analog thermocouple which is read and recorded alongside the CAN signals.

  in any case, I did the front panel so that the user can choose the CAN signals of a drop-down list of all signals in the XNET database and then run the VI to display and record the signals. On the development of PC, it works as expected, I can change the signals before you run the VI.

  When I build and deploy the project I am no longer able to do. The drop-down boxes are grayed out and do not respond to clicks. How to allow the user to choose signals to read and log?

  I've attached a picture to better explain the control of front panel, I have for the user to choose the signals. Nothing complicated just to select the node and right click to create the control. The image is what it looks like on the development of PC, I have not a screen capture of the target device.

  I was able to find a work around. I used an array of enum on the front panel controls that are then wired in a case surrounded by a loop structure for. This generates the signals XNET list based on the table of the enum. Probably not a more elegant solution, but it works and allows the CAN signals to choose in the front panel on the target of RT.

• The SD cards are recommended to be used with the cDAQ 9133?

  Embedded controllers that are the recommended type and size recommended SD cards to be used with the cDAQ Win7 9132 and 9133?

  Hardware specifications for two controllers, you will find that the SD and SDHC cards up to 32 GB are supported.  There is no model or brand recommended, but there are 16 GB (783658 - 01) and 32 GB (783659-01) maps available for purchase through the OR.  You can find those listed in the accessories section available hardware user manual.  See the fees section of the controller product page for more details.

  EDIT: Linked to the UNIFIED and product Messaging page

• NEITHER 9212 - issues with sampling frequency, number of samples and size of buffer or slowness comes together with thermocouple module

  To begin with, I am very new to labview and unfortunately on that my first task is to build something rather complicated for a project that my company works. Fortunately it is especially followed rather than control critical processes.

  Currently, I have a cDAQ with modules, DI, AO, and TC.

  cDAQ-9133

  NEITHER 9472

  NEITHER 9421

  NEITHER 9263

  NEITHER 9205

  NEITHER 9212

  I'm currently running read-write for all 5 of these modules in parallel while loops and analog and digital inputs/outputs modules that all work as expected. Each loop requires 1 sample per channel through the wizard DAQmx etc for each module and I got can interact with all the asyncronosly inputs and outputs which at the moment is the goal. I can switch power switch for each module save memory, or if the need arrives later.

  My problem is that the module TC (NI 9212) when tilt on which allows the acquisition of sample 1 loop seems to take much, much longer to collect samples. I have played with different acquisition parameters and can seem to get a continuous flow of data when you use streaming samples, or even when specifying N-samples but I come in questions where the "application cannot catch up with the hardware.

  I tried to find an optimal number of samples/sampling, rate, etc I can get an update of temperature more than every 1 to 2 seconds, but if I set the number of samples that are high enough to apparently get a constant flow, what ends up happening waveform graphs seem to lag behind the actual data, and that's where I get errors. I only want 1 sample per channel per cycle anyway. Yet once, all the other modules in the cycle with less than 100ms delay between acquisitions but the module thermocouple ends up being 1-2 seconds. It's okay because in our application temperature should not rise/drop very quickly but its boring nonetheless.

  I have the acquisition set up for the same (NI 9212) thermocouple module was like my modules of analog and digital inputs (NI 9205 and NI 9421) take 1 sample every time the task is called so I'm having a hard time understand why do the same for the TC module introduced such a delay. Max sampling rate is supposed to be 95 samples/s/ch, so I guess that the delay must come from call the task over and over again in a loop.

  Synchronization and how you have configured the 9212?

  In the case of high resolution, it can reach 1.8 samples/s. see page 7 of the plug technique here for rates for the supported modes:

  http://www.NI.com/PDF/manuals/374389a.PDF

  -AK2DM

• Unsupported personality: PCL on print Laserjet 1012 from Windows 7 Pro 64-bit

  I have an HP Laserjet 1012.  My PC has Windows 7 Pro 64 bit.  I used the Laserjet 1015 PCL 6 drivers.  When I printed the first two times, it worked fine.  Now each page just print "Unsupported personality: PCL ' at the top.

  What should I do now?

  Thank you for your ' Experts for a day Tech Support.

  Mark

  Hi rbarbo43,

  I found the following thread that will help you during the installation of the printer in Windows 7. Let me know if you need assistance?

  http://h30434.www3.HP.com/T5/printer-networking-and-wireless/LaserJet-1012-driver-for-Windows-7/m-p/351356#M16114

• Elite x 2 1012: Disable "auto rotation" on Elite X 2 1012

  I have a X 2 1012 elite and I can't conrol the function "auto rotation". There is no hardware button and I do not see a combination of keys.

  Yet when I go into the section display settings for Windows 10 "rotation lock" button is grayed out, - I can't select it.

  Any suggestions?

  Shahman,

  I was wondering if your keyboard base is attached when you try to access the setting of auto rotation?

  It should be greyed out when attached and only reactive once detached.

  Sometimes, once separated, you may need to rotate the tablet to portrait. Then the automatic rotation of images button works.

  Have you tried this yet?

• When I try to update iTunes I (-1012) error message what should I do?

  Hello world

  I am trying to download the latest update to iTunes App_Store but the server (l think) prevents me from that and the error message

  "The operation could not be completed. (NSURLErrorDomain error-1012.) -(1012)" appears.

  No matter what kind of suggestion helps solve such a problem is appreciated putting in mind that I always get a black window, whenever I turn on or restart my Mac and there is message says "no bootable disc. "Please enter a '. So I am forced to do it the hard way with the help of the ' alt ' key.

  I have also tried other methods provided by the community in order to resolve the error I get from App_Store such as; concerning keychains an another one about recover host.

  Have you installed something called "Avast?

• 'Manual' HP 1012 Laserjet cleaning Cycle

  Is there a way to launch 'manually' on a HP 1012 Laserjet Printer cleaning cycle? I'm on Windows 7 x 64 (using the work around the drivers), and the software provided cleaning does not work on this OS. Thank you!

  Yes there is! Here's how you can run a manual cleaning cycle:

  1. Load paper photocopier rank in the paper tray.

• X 2 elite 1012: X 2 elite 1012 512 GB

  I'm looking to pre-order the 1012 with 512 GB ssd and the m7 processor. I can't find anywhere. I can not even find a customization option. What is going on?

  Hello donohum77,

  If its not listed on HP store catalog, then it is not yet been made public to see availability.

  Unfortunately, not even HP employees are privileged to make the information.

  HP retains a wrap tight on this type of things.

  I'm sorry.

• X 2 elite 1012 G1: HP Elite Thunderbolt 3 65W USB - C docking station does not not on Elite X 2 1012 G1

  Hello

  I just got the USB docking station - C HP Elite Thunderbolt 3 65W.

  I plugged in and my Elite X 2 1012 G1 fresh, but that's all. No ports do not work. The monitor is not recognized or the other.

  If I plug in my phone via USB, it loads, but not recognize it as a storage device.

  I have looked everywhere and can not find drivers that will solve this problem.

  I have:

  -Shot lightning software installed and running, but still without success.

  -Installed and running "Intel Thunderbolt Firmware Update Utility", but get an error that there is no controller driver.

  Help, please.

  PS. The machine was reimagee with an SOE enterprise. So I don't know if I am missing drivers.

  OK problem is finally resolved.

  Rebuilt everything. Everything is OK now.

  Workstation.

  Lightning blow job.

  Happy customer!

• RD450 MMR, BMC, TSM TMM default username and password

  Someone can point out the default username / password for the management system? Also, since it's ridiculously difficult to find these passwords, anyone have a list of all? We should post to keep them in one place. My favorite is the rd450 manual says to use the help inside the TMM to find info. Pretty hard to do when you can not connect.

  Hello

  The RD450, as well as the TD350, RD350, RD550 and RD650 use ThinkServer System Manager (TSM).

  The default username and password is:

  User name: lenovo
  Password: len0vO (zero capital v O)

• LabVIEW 2014 does support CDAQ 9136

  I use LV 2014 SP1, I wanted to buy CDAQ 9136 Windows controller for one of my projects. I'd like to figure out if I can use the SP1 of 2014 LV with DAQmx15.1 in the program for this controller? User manual CDAQ 9136 does not say anything on the support of LV, just said that DAQmx 15.1 is supported.

  When I tried to add a target CDAQ in SP1 LV2014 with DAQmx15.1, it does not show the CDAQ 9136. I won't use the real time of the CDAQ 9136 version, but I'm confused. Any help would be greatly appreciated.

  

  Nanda,

  I would like to clarify the compatibility for the NOR-9136. It is compatible with DAQmx, starting with DAQmx 15.1. In other words, it can be used as a normal cDAQ chassis in any version of LabVIEW with DAQmx 15.1 or later installed (within reasonable limits). However, compatibility in real-time with the cDAQ-9136 has not introduced before LabVIEW time real 2015 module, which is only compatible with LabVIEW 2015. Thus, to use the cDAQ-9136 as a real-time controller, you will need 2015-LabVIEW and the module time real LabVIEW 2015 or later. This note can be found in DAQmx 15.1 notes for supported devices.

• Impossible to get more than 1 channel to read with DAQmx cDAQ-9172 under Windows 7

  I have the cell load, voltage, and input thermocouple connected to a cDAQ-9172. My sensors entries have been scaled and verified in MAX, and all of them work.  DASYLab 13, the driver is "dcDASY.dll" and the hardware configuration is "NI MAX.

  When I add a task NEITHER-DAQmx Analog Input (that is, a set of scales) it appears correctly. If I add a second channel of the task and select it, I get this message:
  'Channel of task name saved with the module is not available. DASYLab resets the module parameters for usable first channel name task. »
  The name of the task remains the same for each new channel I have Add. If I change the name of the task by using the tab to the drop down menu, it says:
  "You have configured several ways out for the module. If you modify the task, you lose the settings. You want to change the task? »
  Both display the same data channels, and I can't work simultaneously several channels. It seems I missed something obvious, but I can't.

  The parameters are:

  Measurement and Automation Explorer 4.6.1
  NOR-DAQmx 9.0

  Material:-cDAQ-9172
  Slot 1 - NOR 9215 (0-10 Vdc analog voltage)
  Slot 2 - NEITHER 9211 (thermocouple)
  slot 3 - NI 9481 (relay)
  slot 4 - NI 9237 (entry deck w / excitement)
  housing 5 - OR 9402 (DIO)
  slot 6 - NI 9263 (0-10 Vdc output analog)

  Thank you

  You can't perform different tasks (continuous) HERE on a single chassis. The first tasks that starts will be 'the resource booking '.

  Combine the AIs of the various modules in a single task (see photo): start by creating the task of thermocouple. Then add AIs 9237 (e.g. Kraft) and 9215 (volts) using the button with the blue, symbol. Set the mode of synchronization of the task of "continue". Save the task, start DASYLab (second photo).

  Change a task (adding channels, etc.) to the MAX while DASYLab works always, will result in unexpected behavior. To synchronize the configuration of MAX with DASYLab, you will need to close/restart DASYLab or use the 'sync' of the function (see photo 3 "syncmax.jpg"). You can set this function as a shortcut by right-clicking on one of the eight green or grey circle things.

  You should think about an update of the MAX/DAqmx drivers. 9.x is a little outdated.

  Updated at least DAQmx 9.9, better 14.x or 15. 0 (stay far 15 1.x).

• Using instrumented hammer model PCB 086D 50 with the NI9234 module and chassis OR cDAQ 9188

  Hi all

  I need to try to shock with a PCB 086D 50 instrumented hammer hammer. I use the chassis OR cDAQ-9188 with the NI9205 and NI9234 modules. The hammer is connected to the NI9234 and accelerometers are connected to NI9205.

  When I test the modules in SignalExpress I get very good results for the dog, but the accelerometers are ok. Also, if I am controlled the hammer OR Max where I have the option to activate the IEPE the result is ok. In SignalExpress, I couldn't find the option to activate IEPE.

  I have no experience using software, but I started to learn. Does that mean that I need to program the system for my setup in LabVIEW? Also, the installer of the equipment makes sense, the modules that I plugged on the cDAQ can be used simultaneously? Should I have the additional device in order to use the hammer with cDAQ 9188?

  Thank you very much

  Emina

  You can enable IEPE in SignalExpress. Here is a configuration for a single power hammer and three accelerometers a 9234-related.

  

  You don't mention the model for accelerometers. They are also the IEPE sensors? If so, have what conditioning of signals you added before the 9205?

  The Assistant Sound and Vibration (built on SignalExpress) contains an example of Impact Test. The Sound and Vibration Toolkit comes with a sample project for the impact test. With free evaluation period, go ahead and look at how one of these examples is implementing the configuration and the triggered acquisition.