TV connected via the VGA input to HDMI don't get no signal after preparing the Windows message, works fine in safe mode

Similar Questions

• laptop stops shortly after the start, but works well in safe mode / command after chkdk or ckdsk/r

  Problem 1: There are months, my two year old Toshiba Satellite L655 s5096 started losing charge the battery even when it is plugged.
  Sometimes, the problem was solved by using a different wall outlet. I replaced the battery, but eventually the problem comes back.

  Problem 2: at the same time that the problems loading starts, Windows has stopped booting normally. Sometimes repair or restoration leads to a normal start, but sometimes I run Chkdsk/r (Chkdsk sometimes the only works [!]) Mode through safe mode w/Command Prompt.

  Problem 3: There are two days of problems 1 and 2 reappeared, but a few minutes after that Windows starts, my machine stops, even if I am able to run Wndows in Mode safe mode w/network.

  I am correct in surmising that this isn't a motherboard (hardware) problem? I don't really want to have to replace this machine if I don't have to. Is this a Windows problem? Upgrade to Windows 8 would solve the problem? Or is it the result of the virus that escaped my Avast scans?

  I'll install Windows 8 when I checked my automatic online data storage works.

  Hi Denise,

  Thanks for posting your question in the Microsoft Community forum.

  I understand that the computer shuts down shortly after starting. I'll help you with this problem.

  1. what security software is installed?

  2. are you sure the workload problem is not limited to a faulty wall unit?

  3. have you checked with the manufacturer of the computer if it is not a battery problem?

  To resolve this issue, let us try these methods:

  Method 1.

  You can create a new power plan and check if that helps.

  Power plans: frequently asked questions: http://windows.microsoft.com/en-ca/windows7/power-plans-frequently-asked-questions

  Method 2.

  Keep the battery power: http://windows.microsoft.com/en-ca/windows7/conserving-battery-power

  Method 3.

  You can remove the battery and connect the power cable from the wall cabinet and check. If the computer does not stop after the restart, then it might be a problem with the battery.

  For any question related to Windows, please do not hesitate to contact us and we will be happy to help you.

• System Restore won't work, drives available: HP (C :) (Missing)?) Left click on the mouse also stops randomly works, works fine in safe mode.

  My computer is upward, slow-running and my mouse will just randomly stop left click. I can switch the service so click right not left click function, but then cannot do the right click function. I had created a restore point before installing a program called Cain and Abel on my computer and it was just a couple of days.

  When I tried to do a restore, I got a message saying I needed turn the system restore. Then my computer froze so I restarted it and selected "System Recovery" and tried to do a restore to the point that I had created before that Cain has been installed. I got a message saying that the restoration has failed then I restarted mode without failure. When I restarted in safe mode, both left and right click was working again but I got a message saying that something has been altered (I didn't write it down so you do not know what it was). He says to run CHKDSK, which I did and then the computer seemed to work again.

  This is temporary, I lost my left click again and now have swung it for do the right click, left click is supposed to do, but really need to be able to do both types of clicks.

  I go in to the restoration of the system, and it says I need to turn it on. When I go into system properties to turn on, the disc I want to activate to says "HP (C :) (Missing)) ' what this means and how do I do the restore point I have created 2 days ago from work?

  Hi kar fam.

  The question you posted seems to be hardware related. Unfortunately, we are unable to help with changes to the hardware. For more assistance, contact your computer manufacturer.

  Matt
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Laptop Vista stops at the login screen, works ok in safe mode.

  I have a 2 year old Vista laptop. The other day, I went to start and it loaded in the log on screen, and when I entered my password, the whole system just stopped. I tried to boot from the CD, and it's the same thing. I was worried that it was a hardware problem, but when I force him to start safe mode, it is not closed.

  I was going to do a system restore, but it tells me that there is no restore point (no idea how this could be!). So I'll try to transfer my data to an external hard drive and do a reset, but it does not recognize that I hooked up an external hard drive when I'm in Mode safe. (even the Safe Mode with networking).

  I went into msconfig and disabled all THE programs that have started up with Vista (there were many things maybe 6 total) and then I have it load beyond the log on screen, but while I tried to plug in the hard drive and transfer my data, you stop in again.

  Help, please!

  Laurie

  Hi Laurie,

  You can try to disconnect the external hard drive and check to see if you can boot into normal mode.

  If you can start, you can leave the cleanboot State computer and disconnect the external hard drive and check the event viewer for the recent event logs, that is causing the problem.

  You can update the event logs to help us continue troubleshooting.

  Check out the link:

  What are the information in event logs? (Event Viewer)

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-information-appears-in-event-logs-Event-Viewer

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Help please the windows does not start in safe mode

  I have windows 7 and I got a simple error that I need to fix but I need to get into safe mode. I'm doing the tapping of f8, but it just goes to the login page. Ive tried several times and just can't get it

  Hello

  There are 2 methods to get into Safe Mode.

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Windows7

  Use the msconfig method:

  Using the method of System Configuration tool:

  Note: If you have problems to enter Safe Mode using the F8 method, don't use this method to force so that it starts in mode without failure. For reasons that why you should read this.

  1. Close all running programs and open the windows if you are back on the desktop.
  2. Click on the Start () button.
  3. In the search box of the Start Menu, type in msconfig as shown in Figure 12 below.
     
     Figure 12. Windows 7 search box

     Then press enter on your keyboard.

  4. The System Configuration utility will open and you will see a screen similar to the one below.

     Click the Startup tab.

  5. You will now be the home screen as shown below.

     Put a checkmark in the checkbox Start secure

  6. Press the apply button and then press the OK button.
  7. Now, you will see a prompt stating that you must restart the computer to apply the change.

     Click the restart button to restart your computer.

  8. Your computer will now restart directly in Mode without failure. When you get to the Windows 7 logon screen, log on to the computer and perform all the necessary tasks.
  9. When done with your tasks, starting in Safe Mode, start msconfig.
  10. When the program is opened and you are on the general tab, select the Normal startupoption.
  11. Press the apply button, then the OK button.

  See you soon.

• Screen goes black after the log on screen and works fine in safe mode.

  Original title: black screen.

  dv65 Pavilion my laptop starts up, but the screen goes black after the log on screen, judging by its instllation it works, but not the screen. It works very well in SafeMode so. Laptop is 3-4 years. I tried to connect it to my TV but she copy behavior laptop screen. Because of this problem, I had to return to the State of the plant 3 times this month. Plese help!

  Hi Avint,

  Glad to know that you were able to resolve the issue and thank you for sharing information.

• Windows Vista hangs after choosing the identity of the connection. works well in safe mode

  I was able to start windows in safe mode, and then create a new connection profile.  However, Windows doesn't always starts normally.  Using the original profile causes the screen to go black after the "Welcome" screen  Using the new profile causes the screen to go to blue after the Welcome screen.  It's a laptop with nothing fixed.  everything seems to work fine in safe mode, so I think it's a matter of profile.  There is no restore points, so I can't use system restore.  Any thoughts?

  Bob J

  Hello Ripplemaker1,

  I have to agree. This sounds like it may be some kind of malware in game.

  I recommend you create a new thread in the forum security, privacy, and user accounts for this piece of the puzzle.

  Best regards

  Matthew_Ha

• Is there a way to see the ip address of the devices connected via the airport?

  Hello world

  Is there a way to see the ip addresses of the devices connected via the airport? I can see the name of the devices but not what ip are they?

  Thanks in advance.

  Open AirPort Utility

  Hold down the option on your Mac so you double-click on the image of the AirPort router

  Wireless clients are displayed

  Click on the small arrow next to each wireless client to see details about the device and the connection

• Login Creditials fail for desktop connection remotely using IP local. Connection via the hostname works very well in local intranet

  Something happened that broke my remote desktop connection.

  System-Win 7 Pro, with enabled Remote Desktop connections. (Static IP, router configured for port before any RDP to this system)

  For a few years now, I had access to this system via desktop remote with all the problems. I have connected by using the name of the computer on the local network and have also connected using the public IP address with a problem. Name of user and password for one, way worked fine.

  The other day there was a power outage or something, most of my systems was suddenly restarted or turned off, and my router had to be reset. Not sure if this is a coincidence of bad, but now the problem is that connection via the public IP address I get "your credentials did not work" when you try to connect. However, if I connect using the host name within the local chapter of the network of the same name to username/password work very well because they always have.

  That's happened. I'm going crazy trying to figure this out. My remote user cannot log on this system.  Help, please!

  Thank you for taking the time to answer, it's really appreciated. I could solve the problem. I don't know how, but if finally started working again. I have reset my network card and reset IP address static of the machine, that I tried to connect. And after some back and forth with that, all of a sudden he was still working. I was suspicious that my router was causing the trouble because the login failure was due to the fact that I've been routed to another computer, even if the rules of the if correct port forwarding. I just he blamed on the PC from Gremlins. I'll keep this info for future use. Some how all refreshed and began to work again properly.

• Internet Explorer message: "unable to connect via the parameter to wide band".

  When I try to connect to Internet Explorer, I get a message saying unable to connect via the parameter to broadband. We have AT & T Wi - Fi that I seem to be the only one of 4 people in our House, that has a connection problem. We all have different types of computers, some run Windows 7 and others are Vista. Don't no if this material. I preformed a few tests without results of troubleshooting. Help, please

  [Original title: programs network networking Internet site Internet website URL website network]

  Hello

  ·         What is the exact error message you get when connecting to internet?

  ·         Which is the browser you use to access the internet?

  ·         You are able to use other internet applications such as messenger etc?

  I suggest you follow the steps below:

  Method 1:

  Follow the steps in the link below to connect to the internet in the link below:

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Method 2:

  Follow the steps outlined in the article below if you can not connect to internet:

  http://support.Microsoft.com/kb/956196

  Method 3:

  If the steps above do not follow the steps in the link below for network connection problems in windows:

  http://Windows.Microsoft.com/en-us/Windows/help/network-connection-problems-in-Windows

  I hope this helps.

• Unable to connect via the Cisco VPN Client

  Hello

  I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

  I am not able to connect and watch the journal on the SAA

  ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

  ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

  ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

  What could be the reason.

  Concerning

  Hi, I had this same problem, here is the solution:

  When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

  Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

  Well, change your strategy using MD5 isakmp / OF would do the trick.

• Problem after connecting via the USB port of the printer. Error 0x0000007a

  Recently, I plugged my HP Deskjet2360 printer via the USB port on my HP laptop (running w7 Home premium 32-bit) and can not print at all. When I try to print a test page I get the following message ' operation could not be completed. Error 0x0000007a. Operation failed.

  My usual Setup is to have my printer connected to my desktop (Windows XP Pro). My HP laptop is connected via a wireless connection to my home network, which is also connected to my desktop computer. Of course, this means that I have the office turned on to be able to print from my laptop.

  Everything worked great until I decided I'd rather have my connected printer to directly to my laptop via USB.

  When I connect the printer via the USB port on my laptop, windows installs the software and reported no problems. Yet when I try to print a test page, I get the mentioned error. When I then reconnect the printer to the desktop and try to print a test page to my network, I get exactly the same error message. The office and the printer still work fine, it's just that I can't print from my laptop.

  I uninstalled and reinstalled the printer on my laptop with the USB connection and the network, but it still does not work. The resolution of the problems on the laptop reported no problems, and the printer is set as default printer. I also get an another error msg when I click on the Preferences button in the printer properties: address of the 0x5aeba4f1 function caused a protection fault. (code 0xc0000005 exception) Some or all property pages cannot be displayed.

  
  

  The only way I found to get around this is to use windows restore and restore my laptop before the point when I connected the printer via the usb port.

  Any suggestions?

  Hello
   
  This error 0x0000007A describes the data area passed to a system call is too small. ERROR_INSUFFICIENT_BUFFER
  You can try to uninstall and reinstall printer driver and check if that helps.
   
  Here's how you can do:
   
  1. open programs and features by clicking on the Start button, clicking Control Panel, click programs, and then clicking programs and features.
  2. Select a program and then click on uninstall.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  http://Windows.Microsoft.com/en-CA/Windows7/remove-unwanted-programs-from-your-computer
   
  After you have uninstalled the driver to restart the computer, this should install it the appropriate drivers for it. You can also try to download the latest driver from the manufacturers website and install it.
  http://h20000.www2.HP.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=1101015&lang=en&cc=us&TaskID=135&prodSeriesId=1101113&prodTypeId=18972
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly
   
  Why can I not print?
  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print
   
  Kind regards
  Umesh P - Microsoft Support

• Unable to connect via the Internet to my ESXi server. Help, please

  Hi, I had a server ESXi 4.1 at home. When I try to connect via the Internet, it is not working.

  I put ESXi server to firewall and still, I can't ping my server even.

  No idea why?

  Kind regards

  Pawel Lenart

  Sit behind your firewall router esxi, transfer 443 to esxi management IP and ensure that management network vmkernel has the internal IP address of router as its default gateway.

  http://blog.peacon.co.UK

  Please give points for any helpful answer.

  Unofficial list of transfer USB devices work

• Whenever I use my iPhone attaches to internet connection, in the window 'Connections available to the general public', my iPhone is presented as "iPhone 1" the next time that I used it, «iPhone 2 "then 3 then 4 etc.»»

  attaches to the iPhone

  Whenever I use my iPhone attaches to internet connection, in the window 'Connections available to the general public', my iPhone is presented as "iPhone 1" the next time that I used it, «iPhone 2 "then 3 then 4 etc.»»  Currently up to 9. How can I stop this from happening? Or is it still important?

  Hello StevenHuurman

  Try this.

  1. turn on WiFi tethering via the iPhone.

  2 connect the system to the iPhone tethered via the wireless connection.

  3. without closing the iPhone tethering, disconnect the straps of the iPhone system.

  4. now reconnect the system to the loin and Note If the wireless connect denominator increases.

  For the above steps, if you have access to other computers, then try the same steps and allow to know the results of these institutions.

  If the denominator goes up so we know it is a problem with the system and if not then whenever you turn off modem, then again on the iPhone are considered as a new network connection and something has changed in the phone.

  Another thing, you have selected the option for the system to connect automatically when this network is in range?

  Unfortunately I do not know what version of the OS you have here are the steps for Windows Vista and Windows 7. During the installation process for Windows Vista and Windows 7, you will see the option "connect automatically when this network is in range. Make sure that you click this box when you configure the connection to the loin.

  Let me know the results. Thank you.

• Control switch radio wireless (Fn + F5) via the Windows registry / software

  In a school environment, students have discovered that they can cause problems using the software switch Fn + F5 to turn off the Wifi radio. I know that the material LED turns off when this happens, but the teachers are too busy to identify it. The result is that users are unable to connect, and the Windows Welcome screen is not quite intuitive, which gives a message error "there currently no server connection.

  I am interested in applying a "fix" to this problem at startup. Maybe a fix Windows registry to "force" the Lenovo software switch to turn on the Wifi.

  I had a bag autour with a comparison of registry Interstate market and am currently getting the following (among other changes, such as DHCP etc.) diff:

  HKLM\SYSTEM\ControlSet001\Control\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318} \0018\RadioEnable: 0x00000000
  HKLM\SYSTEM\ControlSet001\Control\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318} \0018\RadioEnable: 0x00000001
  HKLM\SYSTEM\CurrentControlSet\Control\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318} \0018\RadioEnable: 0x00000000
  HKLM\SYSTEM\CurrentControlSet\Control\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318} \0018\RadioEnable: 0x00000001

  However, forcing these dwords to 0 x 1 doesn't seem to be enough to turn on the radio.

  Has anyone else had a similar experience? Is there a BIOS/UEFI underlying setting that might be able to be accessed via the software?

  Acxtually that I found after searching a bit more. Can be controlled via the command line:

  "C:\Program Files\Lenovo\HOTKEY\TpFnF5.exe" /wlon