U160 BIOS

Similar Questions

• U160 - fresh WIN7 install

  Hello

  Ive had good fun with my (i5) 0894 IdeaPad U160, at least until my HARD drive crashed and started making horrible noises. (Partition recovery... Miss me you so bad)

  On the HARD drive and went in went an SSD (agility, 64 GB).

  Now, I downloaded a Win 7 (32 bit). ISO, unpacked on a USB key using the "Windows 7 USB DVD Download Tool" and installed. However, it installs Windows 7 is slow.  Miles slower than the Win 7 Home Premium making before. Install WIN 7 took ~ 4 minutes on the SSD, but no action result of windows Explorer in 2 minutes of "not responding". Something within Windows slowdown total. TaskManager shows approximately 2% of the maximum activity all in "not responding". RAM is fine.

  Here's what I've tried so far:

  Used 4 different Win 7 isos: with S.P.1and without, from different sources. Tried the update of Windows.

  Install the drivers for the Chipset and video. Hotfix refuses to install. Not sure if Intel Management Engine installed from each window takes 2 minutes to half an hour to even appear.

  Install the new BIOS.

  My recovery disc is scratched and will not start. Honestly im rather sick of having to run PC decr.apifier with each new installation, so I prefer a clean install anyway. How the hell can a new Windows + U160 not work? is the only option to buy Lenovo recovery for 30 dollars and decra.pify disc my PC again? Or my PC sent to Lenovo for several weeks? (then decra.pify it). Lenovo, will install an operating system on a spare HARD drive?

  He spent about 10 hours now reading the forums and trying to make it work. It seems to be a lot of ppl on the net with a similar problem and zero with a response. Which driver is causing the slowdown?

  OK, answering my own post:

  http://www.WinFuture-Forum.de/index.php?showtopic=184160

  In short:

  Windows has had problems with AHCI drivers.

  Fault lies somewhere with [Windows, manufacturers of disk architecture Council].  A fast drive can lead to a mess while many data access (Installation / games) (Race condition). Download the latest driver AHCI (10 V) from Intel has solved my problem. Fixes to Microsoft or Service Pack for Win7 should help too. Theres also new chipset drivers out there.

  Unfortunatelly it was not possible to run the disk in IDE mode, the pilots had to be installed when the drive kept freezing.

• How to enter the bios to the macbook pro

  Hello

  How enter the macbook (Command + Option + O + F) bios does not work in my MacBook Pro (13-inch, mid 2009).

  Macs with Intel processors as you do not have a bios (firmware 0pen), it uses EFI (Extensible Firmware Interface).

  What you trying to accomplish?

  This is the Office Mac Pro forum. I asked that your post moved to the forum of laptop MacBook Pro or another appropriate forum.

• Update the BIOS

  Hello

  can someone tell me the Bios updates for my machine?

  I need one that is more aggressive on material resources. The appropriate drivers for the GPU would be nice as well. Reading from data bases of Geekbench, this machine is never more than a pretty paperweight to research.

  Thanks for reading

  Details in the following way:

  Motherboard: Apple Inc. Mac-B809C3757DA9BB8D iMac17, 1

  BIOS: Apple Inc. IM171.88Z.0105.B08.1604111319

  Memory: 32768 Mo 1867 MHz DDR3

  Processor: Intel Core i7 - 6700K @ 4.00 GHz

  GPU: AMD Radeon R9 M395X 4096 MB

  macpraxis,

  You confuse a Mac to a Windows window. Mac do not have a bios but they have firmware, if there is any necessary updates to your machine, they are available in the software updates which is located in the Mac App Store. If nothing comes, while your system is up to date and should be left alone.

  If you encounter any problem, perhaps to let us know what it is would open the way for getting help.

• Pavilion dv7 6163 cl: unlock (reset) password on BIOS/CMOS for HP DV7 - 6163cl

  The bios of my notebook (Pavilion dv7 6163 cl) blocked by password, and I never put a password. Could you help me solve?

  Enter the wrong password 3 times or simply leave them blank and press success enter 3 times. You should get a stop code. This zip code here.

  https://BIOS-PW.org/

• Pavilion 15: Bios password

  I have a Pavilion 15-e022sa which I just can't get into the bios as it says I need a password that I never put someone could please help

  Hello

  Enter 60081217

  Kind regards

  DP - K

• 8570p: 8570 bios password

  We have our password bios laptop company typed wrong and how stop us this case? Access the bios has it boot in network again.

  Dear customer,

  Welcome to the Support Forum HP and we are happy to help you.

  This is to inform you that all professional laptops HP Probooks as EliteBook have tighter security than the consumer models infact they do not produce ' stop codes ', the password cannot be derived from the serial number and the

  code is stored in a memory not volatile to remove the cell RTC does not reset the password in this case.

  1. Please take a look at this link.

  http://forums.mydigitallife.info/threads/49497-HP-ProBook-EliteBook-BIOS-password-reset-utility

  1. Replace the BIOS chip

  http://www.eBay.com/ITM/HP-EliteBook-8470p-8470w-8570p-8570w-8770w-programmed-BIOS-chip-no-password-new-/251583542720?PT=LH_DefaultDomain_2 & Hash = item3a938c35c0

  1. Please Contact HP Business Notebook of support they should be able to send a SMC.bin custom file that you can use to reset the password at startup.

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the button white Thumbs Up on the right of say thank you*.

  Make it easier for others to find solutions by checking a response 'accept as Solution' if it solves your problem.

  Thank you

  GBL84

  I'm not an employee of HP

  https://DL.dropboxusercontent.com/u/26983620/Java_Bios/biosunlock.html

• Clocked at 20 degrees warmer since putting on 3.87 Rev A Bios Update on Z420 Workstation

  I have a question:

  Not too long ago I put the Bios Update on A Rev 3.87 was considered to be as critical an update on my workstation Z420 (running Windows 7 Pro 64-bit), and lately I've found that the CPU idling at about 20 degrees more hot than before.  I used to hear creaking noises coming from the computer I learned normally come circuits on the motherboard power delivery, but as long as I heard those CPU would be on average around 50 degrees C at idle.  I hear these noises and now the CPU is on average around 70-75 degrees C at idle.  Not sure what the connection is.  HP performance Advisor tells me I'm in the normal range, but I want to just make sure that with programs like Autodesk Maya there, she become too hot and stop the machine.   I don't know what the temp high-end is considered maximum security.  This change could have due to the update of the Bios?

  Thank you for your response and suggestions.  I check in my BIOS power management settings has been developed the extended mode, but the temperature has always hovered around 70-78 degrees at idle.  I checked Intel spec for this (E5 - 1650 6-core xeon) processor, clocked at 3.2 Ghz by heart, and although he said nothing on the TMax, he mentioned that the TCase (which he defined as the maximum temperature allowed integrated processor heat sink (IHS)) was 64 degrees Celsius.  Now my temperature of the case, according to my HP Performance Advisor version 1.7.7517.0 is only about 24 degrees C, but I put my fan a little higher CPU, about 2009 rpm speed.  This makes a little more noise, but my CPU temp has dropped to about 49 °.  "" Before the change of the fan speed has been slightly more than 1300 RPM while the Advisor I have always said that it is in the range "normal".  Is it good to get the speed of the CPU fan like that or do I have to go a little lower?

  James Holman

• All BIOS options are disabled / grayed out

  I have 8770w with HP ProtectTools active EliteBook and just to have on the security of the TPM secure. I rebooted and tried to access the BIOS, my password is accepted, but virtually all of the options are disabled. Any idea what's going on here?
  Is it the TPM chip?

  In fact, the solution was to open a session in the BIOS as a guest and then configure a BIOS Admin password. Thank you post that.

  It is odd that the default user does not receive the Admin of the BIOS rights.

• Default BIOS password

  Hello everyone,

  I had real trouble moving my Touchsmart 600 - 1030fr to Windows 8. Due to incompatibility of graphics driver, I see nothing on my computer after the startup screen (the one with the blue window).

  I discovered that a change in the BIOS can solve this problem, but my BIOS asks me a password. I tried to reset this password in removal and replacement of the battery from the motherboard. Although he told me that the BIOS has been reversed to the factory settings, the password is always there.

  Is anyone of you know what is the password to the factory settings?

  Also, I read on the forum but

  • The password 12345 found heredoes not work
  • the text which States

  "NOTE: If a new non - HP BIOS is installed, and turn on a password is used, and you don't remember the password to start the computer, see the support document of specification motherboard for your computer model to find the password reset instructions to clear BIOS passwords."
  not help me in my documentation of the computer do me not any suspicion on the specification of the motherboard and it is a real BIOS HP.

  Thanks for your help.

  Here are the specifications of your desktop HP TouchSmart 600-1030fr and it's card mother Pegatron IPP7A-M5 (E60). Please follow these instructions;

  The BIOS password is used to protect the settings of the BIOS against unwanted changes. If you have forgotten your password, you can use this jumper to reset password settings.

  To clear the password BIOS follow these steps:
  
  1 turn off the POWER the computer and unplug the power cord.

  2. Locate the jumper marked CLEARLY P.W.

  3. move the jumper on the PSWD jumper on pins 3-1.

  4 wait about 10 seconds, and then return the jumper to pins 5-3.

  5. connect the power cord and turn on the computer.

  6 hold down the F10 key during the boot process to enter the BIOS setup. You will not be asked a password.

  Diagrams are on the page "card motherboard" for your computer.

• How Flash the BIOS if you cannot start Windows

  Hello

  I have a BIOS virus which prevents ANY version of any operating system Windows to boot at all.

  (Linux will start and run fine)

  So, to solve this problem, I need re-flashing the BIOS.

  Problem is... HP offers only the BIOS as an executable Windows utility.

  Can someone help me figure out a way to Flash the BIOS WITHOUT Windows?

  THX

  Now, in response to this topic, I discovered a solution...

  HPBIOSFILE.exe - writeromfile /-writehexfile /-writehdrfile

  I hope this helps some of you.

  To use this...

  (1) download the executable file (.exe) for BIOS update for your motherboard

  (2) a copy of the program flashing of Award Bios BACK (Google it, easy to find)

  (3) obtain a downloadable copy of the BACK 6.22 (of Microsoft) and create files to start this one.  (possibly another computer to do this).

  (4) start your computer affected in BACK 6.22

  (a) copy the files in a directory

  "(b) using the bold line above... type the name of your BIOS instead of the HPBIOSFILE.exe file ' and run the command.

  You will find yourself with a ROM file, a BIN file and a header file.

  You can now re-Flash your BIOS on your HP computer outside of a Windows environment.

  ENJOY!

• system disabled in bios

  I disabled the admin by compensation password in the bios, set up after installation 8.1.my windows on password power has not allowed, but now I can not connect BIOS, even if I still remember the power on password. Thank you for your help thank you

  Hello

  Enter 67578297

  Kind regards

  DP - K

• TouchSmart HP ENVY 15-j104ea N: BIOS Corruption and Windows Logo + B is DOES not

  Hi guys,.

  I recently got a BIOS corruption this morning based on the indications of 2 key CAPS LOCK flashes. This happened after an accident caused by an UPDATE and a QR code on the page.

  I tried to use the resolution by pressing the logo WINDOWS + B, but it does not work. Is it because of Windows 10 or?

  Kindly help me with this problem. Bravo guys.

  Bloody solved the problem. Kudos to this video. https://www.YouTube.com/watch?v=_aYhDdhcpcA

• NX5000 Bios

  Hi, last week I tried to update my bios in windows mode, so, during the bios update windows has cong61ateun... now nothing when I

  try to start the laptop only led to cd rom drive and hard drive. Does anyone have a suggestion? can I fix my laptop? no way to recover the bios?

  A little question where the bios on the motherboad is located?

  I hope someone can help me.

  Thank you

  I know it's too late to say this, but there is an 'important' WARNING use external power supply when the bios update and not cut the power supply even if the computer seems to freeze.

  If you can always start in DOS, then try version disk bootable back of the update of the bios. But it sounds like the bios is corupted, this option is probably not. I think the best thing to do is send to hp service, unless you now how to open up the case and find the jumper to reset bios.

  BIOS is typically stored in a ROM chip, not on the hard disk.

• Compaq mini cq10 bios password reset

  Please I need help to reset my password of bios compaq mini cq10 CNU0184TCN.

  Hello

  The unlock key is: e9l13uvae9