Similar Questions

• Windows 2008 R2 as a guest cannot get the IP address of the server (VMware workstation 7.1.3 on Windows 7) professional

  Hi gurus,

  I installed VMware workstation 7.1.3 on my Windows 7 laptop professional x64bit and I can run my old VM (XP) without any problems in this regard. And I tried to install a new client (Windows 2008 R2 Standard x 64) on this subject, when I put the NETWORK card in the deck, he cannot get the IP address from my DHCP, always show me error "Windows has detected an IP address conflict...". ", I tried the IP static installation for her also, same result.

  I tried to install a new windows Server 2003 as a guest (also defined as a network bridge), it works very well, can get the IP address from my DHCP or can set a static IP address with no problems. Does anyone have a similar experience on this combination? Any solution to this issue?

  Best regards

  BUGBUG

  I recently managed to get bridge network work with a Windows Server 2003 R2 SP2 guest in VMW Workstation 7.1.4.385536 on a host Windows 7 SP1 Ultimate.

  VirtualBox 4.0.4.70112 is installed on the host and disabling the 'VMware Bridge Protocol' in the 'VirtualBox in Ethernet Adapter"on the host was necessary.

  Outpost Firewall Pro 7.1.0.3415.520.1247 is also installed on the host computer and I used some information from the link below to add some necessary firewall rules.

  http://www.agnitum.com/support/KB/article.php?id=1000061

• VMware Workstation 11 Pro doesn't work on Ubuntu 15.10 x 64.

  Hello

  I used Ubntu 15.04 x 64 as the host for VMware Workstation 11 Pro. It was working fine.

  I've upgraded to Ubuntu 15.10 x 64, and now my computer does not open.

  When I try vmware-Installer:

  $ vmware-Installer

  GTK-Message: could not load module '-gtk-module unity ": libunity-gtk - module.so: Nao e possible open land of objetos compartilhado: land UO diretorio nao found

  (vmware - install .py: 5489): Gtk-WARNING *: Nao faith possible service a tool of temas no module_path: "murrine"

  ...

  ...

  ...

  GTK-Message: could not load module 'canberra-gtk-module': libcanberra-gtk - module.so: Nao e possible open objetos compartilhado land: land UO diretorio nao sown

  $ vmware-Installer - l

  Product product name version

  ==================== ====================

  VMware-workstation 11.1.2.2780323

  How to solve this problem, please?

  Hello

  The problem has been resolved by the release of VMware Workstation 11.1.3:

  $ sudo /etc/init.d/vmware status
  Module vmmon loaded
  Module vmnet loaded
  
  $ sudo /etc/init.d/vmware stop
  Stopping VMware services:
     VMware Authentication Daemon                                        done
     VM communication interface socket family                            done
     Virtual machine communication interface                             done
     Virtual machine monitor                                             done
     Blocking file system                                                done
  
  $ sudo /etc/init.d/vmware start
  Starting VMware services:
     Virtual machine monitor                                             done
     Virtual machine communication interface                             done
     VM communication interface socket family                            done
     Blocking file system                                                done
     Virtual ethernet                                                    done
     VMware Authentication Daemon                                        done
     Shared Memory Available                                             done
  
  $ vmware-installer -t
  Component Name                              Component Long Name                                 Component Version
  =========================================== =================================================== ====================
  vmware-installer                            VMware Installer                                    2.1.0.2758308
  vmware-player-setup                         VMware Player Setup                                 7.1.3.3206955
  vmware-vmx                                  VMware VMX                                          7.1.3.3206955
  vmware-vix-core                             VMware VIX Core for Linux                           1.14.4.3206955
  vmware-network-editor                       VMware Network Editor                               11.1.3.3206955
  vmware-network-editor-ui                    VMware Network Editor User Interface                11.1.3.3206955
  vmware-tools-netware                        VMware Tools for Netware                            9.9.4.3206955
  vmware-tools-windows                        VMware Tools for Windows                            9.9.4.3206955
  vmware-tools-winPre2k                       VMware Tools for Windows (Pre 2000)                 9.9.4.3206955
  vmware-tools-freebsd                        VMware Tools for FreeBSD                            9.9.4.3206955
  vmware-tools-solaris                        VMware Tools for Solaris                            9.9.4.3206955
  vmware-tools-linux                          VMware Tools for Linux                              9.9.4.3206955
  vmware-usbarbitrator                        VMware USB Arbitrator                               14.1.5.3206955
  vmware-player-app                           VMware Player Application                           7.1.3.3206955
  vmware-vix-lib-Workstation1100andvSphere600 VMware VIX Workstation-11.0.0-and-vSphere-6.0.0 Lib 1.14.4.3206955
  vmware-workstation-server                   VMware Workstation Server                           11.1.3.3206955
  vmware-ovftool                              VMware OVF Tool component for Linux                 4.1.0.2982904
  vmware-vprobe                               VMware vProbe                                       7.1.3.3206955
  vmware-workstation                          VMware Workstation                                  11.1.3.3206955      
  
  $ vmware-installer -l
  Product Name         Product Version
  ==================== ====================
  vmware-workstation   11.1.3.3206955
  

• Ubuntu 11.04 very slow after upgrade to VMWare Workstation 8.0

  Hello

  After the update to VMWare Workstation 8.0 my Ubuntu 11.04 comments system (which worked very well with Workstation 7) behaves very slow sometimes.

  Slowly I want to say first that it is very laggy when I scroll conent inside windows, and also when I move windows.

  And with sometimes I want to say that this is not always the case. Sometimes, everything works fine for 1 or 2 hours and she begins and, sometimes, that's the problem immediately after starting Ubuntu.

  The problem occurs when restart Ubuntu does not help. But what is stopping Ubuntu and also restart VMWare Workstation on the host (in my case Windows 7) completely. When I do this and I'm lucky everything seems normal again for a while (1 or 2 hours). After that starts all over again.

  VMWare Tools is installed and the comments system has more then enough resources. I also improved the virtuale image to the latest version so that the new features in Workstation 8.0 are available.

  I first thought that maybe it's a RAM problem but the system begins to lag when there is still 1 GB + RAM available and 0.0% swap used.

  Any ideas what I could do? This is quite annoying...

  You can see the same bug that is described in this thread: http://communities.vmware.com/message/1840185#1840185

• USB foot pedal problem (Infinity IN-USB-2): recognized by Windows but does not work on VMware Workstation 10

  When I connect an Infinity IN-USB-2 pedal for my guest Windows 7 Professional (on Ubuntu 14.04 and VMware Workstation 10.0.2), the pedal gets recognized by Windows and different applications, but by pressing the pedal itself has no effect.

  I downloaded a USB foot pedal Tester (http://vec-infinity-in-usb-1-foot-pedal-tester.soft112.com/) on the client and he acknowledged that the device is connected, but when I pressed on any of the three pedals, the tester has not detected the presses.

  I tried the pedal on a real Windows computer, and it worked fine.

  When I connect the pedals, even with the guest in the foreground, VMware Workstation will appear a dialog box:

  The specified device is claimed by another (usbhid) driver on the host operating system. The device can be used. To continue, the appliance will be first disconnected from its current driver. [Cancel] [OK]

  When I click 'OK', we state above: Windows recognizes that the device is connected, but foot-presses are not detected. My other USB devices are not pop this dialog box. (Click Cancel maintains the device disconnected from the guest.) I don't know if the dialog box is significant or a red herring.

  Here's what/var/log/syslog says when I connect the pedal with the Windows client in the foreground:

  kernel: [281434.822751] usb 2 - 1.7: new low speed USB device number 28 using ehci-pci

  kernel: [281434.920667] usb 2 - 1.7: new USB key found, idVendor is 05f3, idProduct = 00ff

  kernel: [281434.920672] usb 2 - 1.7: new USB device strings: Mfr = 1, product = 2, SerialNumber = 0

  kernel: [281434.920675] usb 2 - 1.7: product: pedal WITH USB

  kernel: [281434.920678] usb 2 - 1.7: manufacturer: VEC

  kernel: [281434.923852] entry: CVE CVE USB pedals as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7/2-1.7:1.0/input/input38

  kernel: [281434.924239] is hid-generic 0003:05F3:00FF.0016: entry, hiddev0, hidraw3: USB HID device v1.00 [CVE CVE USB pedals] on usb-0000:00:1d.0-1.7/input0

  PSG-probe: check the bus 2, device 28: ' / sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7 '.

  PSG-probe: bus: 2, device: 28 is not a MTP device

  And when I click on "OK" to the dialog, he said:

  kernel: [281480.324926] usb 2 - 1.7: reset low speed USB device number 28 using ehci-pci

  kernel: [281480.900448] usb 2 - 1.7: reset low speed USB device number 28 using ehci-pci

  When I unplug the device, it is said:

  kernel: [281517.582472] usb 2 - 1.7: unplug USB, the device number 28

  Thanks for the ideas on solving this problem.

  Answering my own question: I spoke with a salesman who told this pedal does not work on virtual machines for the following reason:

  These pedals are all just Universal USB controllers that require programs or applications to be able to see and recognize them for use. Because they are installed by the base of Windows and Generic USB devices drivers, they can not be seen my remote computers via USB sharing etc.

  They recommended using a hotkey program to work around the problem. I have not tried this solution, but bought a different pedal that works out of the box with VM: a vP-1 vPedal. Lower build quality than infinity (in my opinion) but it works perfectly.

  This is the idea of the key of the seller:

  I have a solution that will allow you to use the pedal as expected if the remote program who need to use supports the use of shortcut keys. For example, these pedals are commonly used with NCH Software Express Scribe professional software. This software can use either a pedal, or you can assign the playback functions to access keys. In the scenario you are talking you re Express Scribe on the remote computer to use keyboard shortcuts, you then install Pedalware (http://www.altoedge.com/pedalware/index.html), a free Windows only the foot pedal utility made by NCH Software, you then use the Pedalware utility to assign the buttons on the pedal of a keyboard shortcut that coincides with those remote program.

• Workstation 8 vmware-workstation-server works not not on Ubuntu 11.10

  Hi people:

  Just, I have upgraded my Ubuntu 10.10 to 11.10 and replaced VMWare Server 2.0 with Workstation 8.02.  It seems that the vmware-workstation-server service is not running.  I'm unable to connect from a web page and the application vmware itself is not able to connect.  When I try to activate the dialog application vmware service I get the following messages in the terminal window where I ran vmware:

  update root@naplesubuntu:~#-rc.d: WARNING: /etc/init.d/vmware-workstation-server LSB missing information
  update - see rc.d: < http://wiki.debian.org/LSBInitScripts >
  Adding system for etc/init.d/vmware-workstation-server start...
  /etc/rc0.d/K01vmware-workstation-server->... /init.d/VMware-Workstation-Server
  /etc/RC6.d/K01vmware-workstation-server->... /init.d/VMware-Workstation-Server
  /etc/RC2.d/S03vmware-workstation-server->... /init.d/VMware-Workstation-Server
  /etc/rc3.d/S03vmware-workstation-server->... /init.d/VMware-Workstation-Server
  /etc/RC4.d/S03vmware-workstation-server->... /init.d/VMware-Workstation-Server
  From Workstation Server: fact

  If I disable the vmware application service, I get the following in the terminal window:

  root@naplesubuntu:~# remove any links of the system for etc/init.d/vmware-workstation-server...
  /etc/rc0.d/K01vmware-workstation-server
  /etc/RC2.d/S03vmware-workstation-server
  /etc/rc3.d/S03vmware-workstation-server
  /etc/RC4.d/S03vmware-workstation-server
  /etc/RC6.d/K01vmware-workstation-server
  Stop server workstation: fact

  If I believe that the service is running, but not doing anything, even though I do not see a specific process for this and there seems to be a vmware-workstation-server executable in/usr/bin.

  Not very well where to go from here.   I tried to uninstall and reinstall the workstation and even using a different port number for the Desktop server, but without any result.

  Suggestions welcome.

  Are you running other services on port 443 on this host?

• How to add a second hard drive Ubuntu Server, that runs on vmware workstation 9

  Hello

  I am running vmware workstation on windows 9 8, and I installed Ubuntu 12.10 as a virtual machine on my SSD. I installed a second hard drive in the machine and use the "Add a HDD" feature on vmware workstation to add and pre-allocate space. The problem is that the drive does not appear in Ubuntu. I have checked/Media and / dev, I expected to see something like /sda *. It is a procedural step, I missed it, please help!

  Do I have to mount the drive in a special way? How can I check if it is properly attached?

  Thank you!

  What you said so far, it's like adding a second physical drive to a physical computer and the operating system cannot access until it was partitioned and formatted, and then it can be mounted.  To do the same thing in a VM!

• ACS 5.3 vmware Workstation Ubuntu

  Hello

  I managed to install ACS 5.3 on vmware 8.0.4 (Ubuntu 12.04).

  I can connect but I have some fatal errors from the server ({0} or 500) when you work wihthin access policies.

  I can not change (or same) selection of selection of unique result of selection of the rule result. That triggered the error message.

  My question:

  VMware workstation is really OK 5.x (I got the same errors with 5.1 and 5.2 even on windows 7 / vmware workstation 9)?

  Best regards.

  Vincent.

  Thank you for following it upwards. + 5.

  Tarik Admani
  * Please note the useful messages *.

• Unable to connect to the server of VMware Workstation

  I'm running ubuntu 13.04 (I know only is not officially supported at this time), however, when I navigate my browser to the virtual server (that I configured it using the port 10250), I get the following message is displayed:

  Access to the denied Web page

  Less

  You are not allowed access to the Web page at https://server:10250 /. You may need to connect.

  Error code: 403

  Status of it running:

  Andrew@server:~$ vmware - version

  VMware Workstation 9.0.2 build-1031769

  Andrew@server:~$ sudo service start vmware-workstation-server

  From Workstation Server: fact

  Andrew@server:~$ sudo netstat - apn | grep vmware

  TCP 0 0 0.0.0.0:10250 0.0.0.0: * LISTEN 7878/vmware-pass

  TCP 0 0 127.0.0.1:8307 0.0.0.0: * LISTEN 7878/vmware-pass

  TCP 0 0 0.0.0.0:902 0.0.0.0: * LISTEN 1703/vmware-authdla

  tcp6 0 0: 10250: * LISTEN 7878/vmware-pass

  UNIX 2 [ACC] STREAM LISTENING 37086 6047/vmware-unite-h/tmp/vmware-root/unity-helper-ipc-: 1

  UNIX 2 [ACC] STREAM LISTENING 11814 1991/vmware-usbarbi/var/run/vmware/usbarbitrator-socket

  UNIX 2 [ACC] STREAM LISTENING 42569 7878/vmware-pass/var/run/vmware/proxy-Web server

  UNIX 2 [ACC] STREAM LISTENING 42580 7878/vmware-pass/var/run/vmware/root_0/1371168951002706_7878/ha-nfc-fd

  UNIX 2 [ACC] STREAM LISTENING 42587 7878/vmware-pass/var/run/vmware/root_0/1371168951002706_7878/ha-nfcssl-fd

  [of] UNIX 2 CONNECTED FLOW 37087 6047/vmware-unite-h/tmp/vmware-root/unity-helper-ipc-: 1

  [of] UNIX 3 CONNECTED STREAM 35127 5534/vmware-tray

  [of] UNIX 3 CONNECTED STREAM 6047/vmware-unite-h 35819

  [of] UNIX 3 CONNECTED STREAM 43388 7878/vmware-pass

  [of] UNIX 3 CONNECTED STREAM 42564 1991/vmware-usbarbi/var/run/vmware/usbarbitrator-socket

  I get this message, if I run it on the local host, or if I run it on another machine.

  It's the only thing I see in syslog:

  Cat/var/log/syslog | grep vmware

  June 13 to 17:04:04 server/usr/lib/vmware/bin/vmware-hostd [8970]: password accepted for user andrew 127.0.0.1

  June 13 to 17:37:04 server/usr/lib/vmware/bin/vmware-hostd [8970]: password accepted for user andrew 127.0.0.1

  June 13 to 17:54:56 Server/usr/lib/vmware/bin/vmware-hostd [8970]: password accepted for user andrew 127.0.0.1

  June 13 to 17:55:28 vmauthd Server [4593]: vthread-3 | I120: [msg.dictionary.load.openFailed] cannot open the file ' / usr/lib/vmware/settings ': no such file or directory.

  June 13 to 17:55:28 vmauthd Server [4593]: vthread-3 | I120: Preferences file of the option PREFS not found in/usr/lib/vmware/settings. Using the default values.

  June 13 to 17:55:28 vmauthd Server [4593]: vthread-3 | I120: Acquired the lock to/var/run/vmware/authd_14937f64dcf6846b509ee5705e0270eb

  June 13 to 17:55:28 vmauthd Server [4593]: vthread-3 | I120: unlocked lock for/var/run/vmware/authd_14937f64dcf6846b509ee5705e0270eb

  June 13-20:13:42 Server/usr/lib/vmware/bin/vmware-hostd [2275]: password accepted for the 127.0.0.1 root user

  13 June at 20:13:48 Server/usr/lib/vmware/bin/vmware-hostd [2275]: password accepted for the 127.0.0.1 root user

  13 June at 20:13:55 Server/usr/lib/vmware/bin/vmware-hostd [2275]: password accepted for the 127.0.0.1 root user

  June 13-20:14:02 Server/usr/lib/vmware/bin/vmware-hostd [2275]: password accepted for the 127.0.0.1 root user

  June 13-20:14:06 server named [1418]: fix error (network unreachable) 'my.vmware.com.edgekey.net/A/IN': 2600:1401:2:42 #53

  13 June at 20:14:09 Server/usr/lib/vmware/bin/vmware-hostd [2275]: password accepted for the 127.0.0.1 root user

  13 June at 20:14:29 / usr/lib/vmware/bin/vmware-hostd [2275]: last message repeated 2 times

  13 June at 20:14:29 / usr/lib/vmware/bin/vmware-hostd Server [7008]: password accepted for the 127.0.0.1 root user

  13 June at 20:15:02 / usr/lib/vmware/bin/vmware-hostd [7008]: last message repeated 3 times

  13 June at 20:15:04 the server kernel: [3056.496451] vmware-gksu [7037]: Segfault at 7f353f7591aa ip 00007f3547c38156 sp 00007fff95cf93d8 error 4 to libc - 2.17.so [7f3547bb0000 + 1be000]

  13 June at 20:15:05 Server/usr/lib/vmware/bin/vmware-hostd [7008]: password accepted for the 127.0.0.1 root user

  13 June at 20:15:07 the server kernel: [3059.388927] vmware-gksu [7085 or]: segfault at 7fc4c9f331aa ip 00007fc4d253b156 sp 00007fff04d21118 error 4 to libc - 2.17.so [7fc4d24b3000 + 1be000]

  13 June at 20:15:09 the server kernel: [3060.572580] vmware-gksu [7130]: Segfault at 7f68319561aa ip 00007f6835e04156 sp 00007fff7ce94c98 error 4 to libc - 2.17.so [7f6835d7c000 + 1be000]

  13 June at 20:15:09 Server/usr/lib/vmware/bin/vmware-hostd [7008]: password accepted for the 127.0.0.1 root user

  13 June at 20:15:14 Server/usr/lib/vmware/bin/vmware-hostd [7008]: password accepted for the 127.0.0.1 root user

  13 June at 20:15:17 the server kernel: [3069.298603] vmware-gksu [7548]: Segfault at 7f4d5bdeb507 ip 00007f4d64350156 sp 00007fff78106918 error 4 to libc - 2.17.so [7f4d642c8000 + 1be000]

  So I was wondering if anyone else has similar problems, I thought maybe it was the port that he was running on, and chrome doesn't, unfortunately, I can't find a way to change the port (as running with root, does not this either).

  I was confused Workstation Server with WSX.

• Windows7 + VMware workstation installation of ubuntu

  at the beginning sorry for my weak English level: P

  I had a problem

  I installed on my computer laptop windows 7 and vmware workstation 7 and I want to install ubuntu 9.04, but is not start the linux iso file, I had, iso file is good, I guess it's sort of a simple problem, I installed windows Server 2008 without any problem on vmware workstation but ubuntu doesn't even start...

  http://img31.imageshack.us/i/55688166.jpg/

  http://img199.imageshack.us/i/39370867.jpg/

  http://img683.imageshack.us/i/60346614.jpg/

  I thought there may be a problem with NIC so here, I try to boot after the removal of this

  http://img707.imageshack.us/i/80746708.jpg/

  http://img156.imageshack.us/i/47216333.jpg/

  my windows 7 has been installed juice, I have no problem with the hardware on the laptop

  > at first sorry for my weak English level: P

  Seems OK to me

  1 you have the CDROM 'reader' (your iso file) to connect to turn on? (Settings/CD/DVD of the VM)

  2 did you hit escape when BIOS starts and then tell it to boot from the CD?

  3. all entries in log file of your VM machine?

  A CD created from the file iso bootable in your machine?

  Lou

• VMWare Workstation 12 and 18 of Linux Mint (Ubuntu 16.04) and vmware tools or open-vmware-tools

  I created a new virtual machine using VMWare Workstation 12.1.1 build-3770994 with a guest OS from Linux Mint 18 (which is built on top of Ubuntu 16.04). I have two monitors on my system, the two 2560 x 1440. I am unable to get this virtual machine Linux Mint 18 to cover all of my two monitors when I disable "Accelerate 3D graphics" in my vm settings, I get an error. I have another Linux Mint 17 VM running on the same VMWare Workstation 12 on the same host machine from Windows 10 and it is able to expand on my two monitors very well with "Accelerate 3D graphics" disabled, but he does not open-vmware-tools.

  I have read instructions telling me to install open-vm-Tools-Office in this guest operating system of Linux Mint 18. I did it. Then I restart the guest operating system. When starting, I can click on 'Enter full screen mode' in my menu of VMWare Workstation, and the guest OS has a monitor as expected. When I then click on "Cycle multiple monitors", I get the following error. "The virtual machine could not be changed to the selected screen layout. If you add a monitor to the host computer, you must turn off and turn on the virtual machine to use this monitor. »

  

  I can optimize my VM to automatic adjustment, only one of my two screens, but not both. I tried to uninstall and reinstall open-vm-tools, open-vm-tools-desktop and restart. I tried to use /vmware-tools-distrib/vmware-install.pl's original vmware tools and who does not work either.

  In my vmware.log, I get these two lines that occur when I get the above error.

  2016 07-12 T 15: 43:19.068 - 06:00 | MKS | I125: ToolsSetDisplayTopology: send rpcMsg = 1 DisplayTopology_Set, 0 0 2560 1440

  2016 07-12 T 15: 43:24.768 - 06:00 | MKS | I125: ToolsSetDisplayTopology: rpcMsg sending = DisplayTopology_Set 2, 0 0 2560 1440, 2560 0 2560 1440

  2016 07-12 T 15: 43:24.853 - 06:00 | vCPU-1 | I125: TOOLS of the call to DisplayTopology_Set failed.

  When I activate "Accelerate 3D graphics" with the configuration described above, I am able to use both of my monitors. Why is this the case?

  I think remember having to disable "Accelerate 3D graphics" in my Linux Mint 17 comments vm because it would crash randomly. I try to run this VM Linux Mint 18 with 3D acceleration and see if it crashes, but why is there a difference with spanning multiple monitors?

  Thank you.

  I didn't experience this problem for a few weeks. I don't have a definitive answer to my original problem.

  I installed Mate instead of cinnamon 3 to my MINT 18. Then, I created a new VM with Ubuntu Gnome 3 16.04 running as the OF. I did have problems with both approaches. I also tried using Firefox as my main browser instead of Chrome, as I read that Chrome can have problems of memory. It could be a combination of several of these changes that have allowed me to work without problems.

  Knowing what I know now, I think the move away from cinnamon 3 is what seems to have fixed my problems. I can certainly say that you use Firefox consumes less memory, as I can monitor the monitor system under Ubuntu. Chrome would eventually eat all my system memory, that I could see. The extent of the why? I'm not sure at this point.

• 15 Ubuntu won't start in VMware workstation 12 after a recent update of Ubuntu

  I'm quite new to the environment virtual system and linux. Someone could me help on my question below?

  I have a virtual system installed using VMware workstation 12. It works fine, until the upgrade of Ubuntu this morning.

  I have no idea what the update installed.

  After the required reboot, Windows VMware has always stop a black page.

  Before everything, there were some posts that I think they should be useful to target the issue here.

  

  He said:

  SMbus host controller not activated!

  No valid rapl area found within the package 0

  Thank you very much for your help!

  -Ninggang

  I found a solution!

  There is problem of ubuntu, new kernel is bad and it's a bug.

  To start again just hold SHIFT while your machine virtual machine to the menu shows ubuntu boot.

  Select Advanced, then choose more old kernel version and that's all.

  After you restart your virtual machine it always start on black screen, you need to delete newes kernel version linux-headers - 4.2.0 - 30 to begin on the old version and problem SOLVED!

  remove the kernel:

  sudo apt-get remove linux-image-4.2.0-30-generic
sudo update-grub2

  reboot.

• Certificate expired on a server that has only the client VMware and VMware workstation

  Our scanners detected security certificate expired vmware on a server. The only products currently running on this server are VMware workstation and the vSphere client. I looked in all the installed certificates and their lack of vmware. When I open a web browser and go to the IP address of servers using port 443 I get a message of invalid certificate and look a certificate it shows expired recently, and was published by VMware. Where can I find this certificate and what is used to indicated the products installed on this system?

  The certificate was for workstation server configurations (connection sharing VMs/Remote). Just disabled the sharing feature because it is not used.

  Find the certificate in the program data-file VMware. Could not find information on renewal, only how to replace it.

• Installation of Windows Server 2008 R2 on vmware workstation 9

  Hello

  I have a laptop with windows 7 OS and installed a VM with windows server 2008 R2 OS using vmware workstation 9. The thing is without creating any user, VM is turining IT with the user that I connected my laptop. Is that how it behaves.

  Generally, when install us windows server on a physical machine, he asks to open a session with the administrator by changing the password.

  Could someone let me know how to change this?

  Thanks in advance

  This problem occur if you select the OS install disc when the VM... in this way creating the VMware Workstation uses a feature called Easy Install, where you will be asked for more information, including the user credentials.

  To avoid using Easy Install, during the creation of the VM, on install, select "I will install the operating system later":

  

  To read more about Easy Install, check page 35: http://www.vmware.com/pdf/desktop/ws90-getting-started.pdf

• Installation of Windows Server 2003 on vmware workstation 9

  Hello

  I try to install windows server 2003 R2 x 64 edition as a guest OS on vmware workstation 9. But it gives me the time hard the same installation.

  First I had the

  "found no hard drives installed in your computer error.

  I was able to fix this by downloading it pilot vmware scsi. Now I get NTLDR is missing, restart the computer.

  
  

  I have install windows OS was frank. Anyone faced this problem. Please advise me? I have 2 CD (Cd1 and Cd2) of Windows server 2003 edition.

  
  

  Any help is appreciated

  
  

  Thanks in advance
  

  
  

  1 you shouldn't have to download all the drivers for the vHDD, as LSI Logic drivers are included in Windows Server 2003.  In other words, you have not selected correct SCSI (LSI Logic) controller.

  Now I get NTLDR is missing, restart the computer.

  Make sure that the disk is disconnected.