Unable to access the local network with VPN with some ISPS
Hello
We have a VPN Remote Access IPSEC with an ASA5505. Install VPN it correctly but can not access the inside or the ASA to my office.
But at home with another Internet service provider, it works! You can access inside.
We are trying with other ISP and it works with 2 and does not work with the other 2!
Office we also have an ASA5505, but we have another VPN other sites that work properly.
Any ideas?
Thank you and sorry for my English.
Add...
ISAKMP nat-traversal crypto
That should do the trick! Please rate if this can help.
Tags: Cisco Security
Similar Questions
-
remote VPN and vpn site to site vpn remote users unable to access the local network
As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config
The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.
ASA Version 8.2 (2)
!
host name
domain kunchevrolet
activate r8xwsBuKsSP7kABz encrypted password
r8xwsBuKsSP7kABz encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group dataone
IP address pppoe
!
interface Ethernet0/1
nameif inside
security-level 50
IP 192.168.215.2 255.255.255.0
!
interface Ethernet0/2
nameif Internet
security-level 0
IP address dhcp setroute
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
passive FTP mode
clock timezone IST 5 30
DNS server-group DefaultDNS
domain kunchevrolet
permit same-security-traffic intra-interface
object-group network GM-DC-VPN-Gateway
object-group, net-LAN
access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 Internet
IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
LOCAL AAA authentication serial console
Enable http server
x.x.x.x 255.255.255.252 out http
http 192.168.215.0 255.255.255.252 inside
http 192.168.215.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 65500 transform-set RIGHT
card crypto 10 VPN ipsec-isakmp dynamic dynmap
card crypto VPN outside interface
card crypto 10 ASA-01 set peer 221.135.138.130
card crypto 10 ASA - 01 the transform-set RIGHT value
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
the Encryption
sha hash
Group 2
lifetime 28800
Telnet 192.168.215.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access inside
VPDN group dataone request dialout pppoe
VPDN group dataone localname bb4027654187_scdrid
VPDN group dataone ppp authentication chap
VPDN username bb4027654187_scdrid password * local store
interface for identifying DHCP-client Internet customer
dhcpd dns 218.248.255.141 218.248.245.1
!
dhcpd address 192.168.215.11 - 192.168.215.254 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Des-sha1 encryption SSL
WebVPN
allow outside
tunnel-group-list activate
internal kun group policy
kun group policy attributes
VPN - connections 8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
kunchevrolet value by default-field
test P4ttSyrm33SV8TYp encrypted password username
username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
username kunauto attributes
Strategy Group-VPN-kun
Protocol-tunnel-VPN IPSec
tunnel-group vpngroup type remote access
tunnel-group vpngroup General attributes
address pool VPN_Users
Group Policy - by default-kun
tunnel-group vpngroup webvpn-attributes
the vpngroup group alias activation
vpngroup group tunnel ipsec-attributes
pre-shared key *.
type tunnel-group test remote access
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
: end
kunauto #.Hello
Looking at the configuration, there is an access list this nat exemption: -.
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
But it is not applied in the States of nat.
Send the following command to the nat exemption to apply: -.
NAT (inside) 0 access-list sheep
Kind regards
Dinesh Moudgil
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
-
Easy VPN not able to access the local network
Hi guys,.
little hope can help me, I'll give you a run down on the config.
I have a border router that is a no. 2851 connected to the No. 2851 is a switch cisco 3750 running Routing inter - vlan with four VLANS.
I have easy VPN server on the edge router No. 2851 I am able to connect remotely from a client vpn cisco with a problem but I can't access the local network on the server, I tried everything with no luck.
I have a cisco VPN client installed on a 64-bit windows system 7 and I also tried with windows xp 32-bit system and still no luck.
Please I need help I need to get this race to end of trading today.
I will be copying and pasting the edge router config please if someone get review and see if the config is good.
You need to change your ACL PAT of standard to extend and to deny traffic to be translated to the Pool of VPN:
access-list 120 deny ip 10.10.10.0 0.0.0.3 10.10.50.0 0.0.0.255
access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 deny ip 172.16.XX.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 deny ip 172.1X.20.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 deny ip 192.168.XX.0 0.0.0.255 10.10.50.0 0.0.0.255
access-list 120 allow ip 10.10.10.0 0.0.0.3 all
IP access-list 120 permit 192.168.XX.0 0.0.0.255 any
IP access-list 120 permit 172.16.XX.0 0.0.0.255 aniy
IP access-list 120 permit 172.1X.20.0 0.0.0.255 any
IP access-list 120 permit 192.168.XX.0 0.0.0.255 any
overload of IP nat inside source list 120 interface Dialer0
no nat ip within the source of the list 1 overload interface Dialer0
clear the ip nat trans *.
Hope that helps.
-
ASA 5505 IPSEC VPN connected but cannot access the local network
ASA: 8.2.5
ASDM: 6.4.5
LAN: 10.1.0.0/22
Pool VPN: 172.16.10.0/24
Hi, we purcahsed a new ASA 5505 and try to configure IPSEC VPN via ASDM; I simply run the wizards, installation vpnpool, split tunnelling, etc.
I can connect to the ASA using the cisco VPN client and internet works fine on the local PC, but it can not access the local network (can not impossible. ping remote desktop). I tried the same thing on our Production ASA(those have both Remote VPN and Site-to-site VPN working), the new profile, I created worked very well.
Here is my setup, wrong set up anything?
ASA Version 8.2 (5)
!
hostname asatest
domain XXX.com
activate 8Fw1QFqthX2n4uD3 encrypted password
g9NiG6oUPjkYrHNt encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.1.1.253 255.255.252.0
!
interface Vlan2
nameif outside
security-level 0
address IP XXX.XXX.XXX.XXX 255.255.255.240
!
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS server-group DefaultDNS
domain vff.com
vpntest_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.252.0
access extensive list ip 10.1.0.0 inside_nat0_outbound allow 255.255.252.0 172.16.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
logging trap warnings
asdm of logging of information
logging - the id of the device hostname
host of logging inside the 10.1.1.230
Within 1500 MTU
Outside 1500 MTU
IP local pool 172.16.10.1 - 172.16.10.254 mask 255.255.255.0 vpnpool
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol nt AD
AAA-server host 10.1.1.108 AD (inside)
NT-auth-domain controller 10.1.1.108
Enable http server
http 10.1.0.0 255.255.252.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 10.1.0.0 255.255.252.0 inside
SSH timeout 20
Console timeout 0
dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal group vpntest strategy
Group vpntest policy attributes
value of 10.1.1.108 WINS server
Server DNS 10.1.1.108 value
Protocol-tunnel-VPN IPSec l2tp ipsec
disable the password-storage
disable the IP-comp
Re-xauth disable
disable the PFS
IPSec-udp disable
IPSec-udp-port 10000
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpntest_splitTunnelAcl
value by default-domain XXX.com
disable the split-tunnel-all dns
Dungeon-client-config backup servers
the address value vpnpool pools
admin WeiepwREwT66BhE9 encrypted privilege 15 password username
username user5 encrypted password privilege 5 yIWniWfceAUz1sUb
the encrypted password privilege 3 umNHhJnO7McrLxNQ util_3 username
tunnel-group vpntest type remote access
tunnel-group vpntest General attributes
address vpnpool pool
authentication-server-group AD
authentication-server-group (inside) AD
Group Policy - by default-vpntest
band-Kingdom
vpntest group tunnel ipsec-attributes
pre-shared-key BEKey123456
NOCHECK Peer-id-validate
!
!
privilege level 3 mode exec cmd command perfmon
privilege level 3 mode exec cmd ping command
mode privileged exec command cmd level 3
logging of the privilege level 3 mode exec cmd commands
privilege level 3 exec command failover mode cmd
privilege level 3 mode exec command packet cmd - draw
privilege show import at the level 5 exec mode command
privilege level 5 see fashion exec running-config command
order of privilege show level 3 exec mode reload
privilege level 3 exec mode control fashion show
privilege see the level 3 exec firewall command mode
privilege see the level 3 exec mode command ASP.
processor mode privileged exec command to see the level 3
privilege command shell see the level 3 exec mode
privilege show level 3 exec command clock mode
privilege exec mode level 3 dns-hosts command show
privilege see the level 3 exec command access-list mode
logging of orders privilege see the level 3 exec mode
privilege, level 3 see the exec command mode vlan
privilege show level 3 exec command ip mode
privilege, level 3 see fashion exec command ipv6
privilege, level 3 see the exec command failover mode
privilege, level 3 see fashion exec command asdm
exec mode privilege see the level 3 command arp
command routing privilege see the level 3 exec mode
privilege, level 3 see fashion exec command ospf
privilege, level 3 see the exec command in aaa-server mode
AAA mode privileged exec command to see the level 3
privilege, level 3 see fashion exec command eigrp
privilege see the level 3 exec mode command crypto
privilege, level 3 see fashion exec command vpn-sessiondb
privilege level 3 exec mode command ssh show
privilege, level 3 see fashion exec command dhcpd
privilege, level 3 see the vpnclient command exec mode
privilege, level 3 see fashion exec command vpn
privilege level see the 3 blocks from exec mode command
privilege, level 3 see fashion exec command wccp
privilege see the level 3 exec command mode dynamic filters
privilege, level 3 see the exec command in webvpn mode
privilege control module see the level 3 exec mode
privilege, level 3 see fashion exec command uauth
privilege see the level 3 exec command compression mode
level 3 for the show privilege mode configure the command interface
level 3 for the show privilege mode set clock command
level 3 for the show privilege mode configure the access-list command
level 3 for the show privilege mode set up the registration of the order
level 3 for the show privilege mode configure ip command
level 3 for the show privilege mode configure command failover
level 5 mode see the privilege set up command asdm
level 3 for the show privilege mode configure arp command
level 3 for the show privilege mode configure the command routing
level 3 for the show privilege mode configure aaa-order server
level mode 3 privilege see the command configure aaa
level 3 for the show privilege mode configure command crypto
level 3 for the show privilege mode configure ssh command
level 3 for the show privilege mode configure command dhcpd
level 5 mode see the privilege set privilege to command
privilege level clear 3 mode exec command dns host
logging of the privilege clear level 3 exec mode commands
clear level 3 arp command mode privileged exec
AAA-server of privilege clear level 3 exec mode command
privilege clear level 3 exec mode command crypto
privilege clear level 3 exec command mode dynamic filters
level 3 for the privilege cmd mode configure command failover
clear level 3 privilege mode set the logging of command
privilege mode clear level 3 Configure arp command
clear level 3 privilege mode configure command crypto
clear level 3 privilege mode configure aaa-order server
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:447bbbc60fc01e9f83b32b1e0304c6b4
: end
Captures we can see packets going from the pool to the internal LAN, but we do not reply back packages.
The routing must be such that for 172.16.10.0/24 packages should reach the inside interface of the ASA.
On client machines or your internal LAN switch, you need to add route for 172.16.10.0/24 pointing to the inside interface of the ASA.
-
Need help to access the internal network via VPN on ASA5505 8.4 (1)
Recently, I upgraded my ASA5055 from 8.02 to 8.4 and since I have updated to the new version I can access my home network is no longer through the VPN. I can connect to the VPN with no problems however I can no longer ping or you connect to my network of 10.0. Someone would be kind enough to look at my config and tell me what needs to be added to make it work? In my old config, I had a statement of NAT for VPN that is no longer here.
I also wanted to configure WebVPN to work as well, and this is something that I've never been able to understand. Is it also possible that I can be on my 20.0 network and connect to the VPN and access 10.0 as well? When it is connected to my network of 20.0 I'm not received credentials to connect to the VPN. I would be grateful if someone can help out me. The major part of this is the first part of this question.
My configuration:
ASA Version 8.4 (1)
!
ASA5505 hostname
domain xxxxxxxx.dyndns.org
enable encrypted password xxxxxxxxxxxx
xxxxxxxxxxxxxxx encrypted passwd
names of
nameserver 192.168.10.2
Office of name 192.168.10.3
name Canon 192.168.10.5
name 192.168.10.6 mvix
name 192.168.10.7 xbox
name 192.168.10.8 dvr
name 192.168.10.9 bluray
name 192.168.10.10 lcd
name 192.168.10.11 mp620
name 192.168.10.12 kayla
name 192.168.1.1 asa5505
name 192.168.1.2 ap1
name 192.168.10.4 mvix2
name 192.168.10.13 lcd2
name 192.168.10.14 dvr2
!
interface Vlan1
nameif management
security-level 100
IP address asa5505 255.255.255.248
management only
!
interface Vlan2
0050.8db6.8287 Mac address
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan10
nameif private
security-level 100
IP 192.168.10.1 255.255.255.224
!
interface Vlan20
nameif Public
security-level 100
IP 192.168.20.1 255.255.255.224
!
interface Ethernet0/0
Description pointing to WAN
switchport access vlan 2
!
interface Ethernet0/1
Uplink port Linksys 12 description
switchport access vlan 10
!
interface Ethernet0/2
Description Server 192.168.10.2/27
switchport access vlan 10
!
interface Ethernet0/3
Uplink Eth1 management description
!
interface Ethernet0/4
switchport access vlan 30
!
interface Ethernet0/5
switchport access vlan 30
!
interface Ethernet0/6
switchport access vlan 30
!
interface Ethernet0/7
Description of Cisco 1200 Access Point
switchport trunk allowed vlan 1,10,20
switchport trunk vlan 1 native
switchport mode trunk
!
Banner motd users only, all others must disconnect now!
boot system Disk0: / asa841 - k8.bin
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS server-group DefaultDNS
domain xxxxxxx.dyndns.org
network object obj - 192.168.50.0
192.168.50.0 subnet 255.255.255.0
Server network objects
host 192.168.10.2
network object obj - 192.168.10.0
192.168.10.0 subnet 255.255.255.224
network object obj - 192.168.20.0
subnet 192.168.20.0 255.255.255.224
network server-01 object
host 192.168.10.2
network server-02 object
host 192.168.10.2
xbox network object
Home 192.168.10.7
xbox-01 network object
Home 192.168.10.7
xbox-02 network object
Home 192.168.10.7
xbox-03 network object
Home 192.168.10.7
xbox-04 network object
Home 192.168.10.7
network server-03 object
host 192.168.10.2
network server-04 object
host 192.168.10.2
network server-05 object
host 192.168.10.2
Desktop Network object
host 192.168.10.3
kayla network object
Home 192.168.10.12
Home_VPN_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.224
outside_access_in list extended access permit tcp any any eq 3389
outside_access_in list extended access permit tcp any any eq 2325
outside_access_in list extended access permit tcp any eq ftp server object
outside_access_in list extended access permit tcp any any eq 5851
outside_access_in list extended access udp allowed any any eq 5850
outside_access_in list extended access permit tcp any any eq pptp
outside_access_in list extended access udp allowed any any eq syslog
outside_access_in list extended access udp allowed any any eq 88
outside_access_in list extended access udp allowed any any eq 3074
outside_access_in list extended access permit tcp any any eq 3074
outside_access_in list extended access permit tcp any any eq field
outside_access_in list extended access udp allowed any any eq field
outside_access_in list extended access permitted tcp everything any https eq
outside_access_in list extended access permit tcp any eq ssh server object
outside_access_in list extended access permit tcp any any eq 2322
outside_access_in list extended access permit tcp any any eq 5900
outside_access_in list extended access permit icmp any any echo response
outside_access_in list extended access permit icmp any any source-quench
outside_access_in list extended access allow all unreachable icmp
outside_access_in list extended access permit icmp any one time exceed
outside_access_in list extended access udp allowed any any eq 5852
KaileY_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.224
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer of 36000
logging warnings put in buffered memory
recording of debug trap
asdm of logging of information
address record [email protected] / * /
exploitation forest-address recipient [email protected] / * / level of errors
Management Server host forest
MTU 1500 management
Outside 1500 MTU
MTU 1500 private
MTU 1500 Public
local pool IPPOOL 192.168.50.2 - 192.168.50.10 255.255.255.0 IP mask
local pool VPN_POOL 192.168.100.2 - 192.168.100.10 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ASDM image disk0: / asdm - 641.bin
don't allow no asdm history
ARP timeout 14400
!
Server network objects
NAT (private, foreign) static tcp ftp 5851 service interface
network object obj - 192.168.10.0
NAT (private, foreign) dynamic interface
network object obj - 192.168.20.0
NAT (outside) dynamic public interface
network server-01 object
NAT (private, outside) interface static 2325 2325 tcp service
network server-02 object
NAT (private, outside) interface static udp syslog syslog service
xbox network object
NAT (private, outside) interface static service udp 88 88
xbox-01 network object
NAT (private, outside) interface static service udp 3074-3074
xbox-02 network object
NAT (private, outside) interface static service tcp 3074-3074
xbox-03 network object
NAT (private, outside) interface static tcp domain domain service
xbox-04 network object
field of the udp NAT (private, foreign) of the static interface function
network server-03 object
NAT (private, outside) interface static tcp https https service
network server-04 object
Static NAT (private, outside) interface service tcp ssh 2322
network server-05 object
NAT (private, outside) interface static 5900 5900 tcp service
Desktop Network object
NAT (private, outside) interface static service tcp 3389 3389
kayla network object
NAT (private, outside) interface static service udp 5852 5852
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http 192.168.1.0 255.255.255.248 management
redirect http outside 80
location of SNMP server on the Office floor
SNMP Server contact [email protected] / * /
Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start
No vpn sysopt connection permit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map pfs set 20 Group1
Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1
life together - the association of security crypto dynamic-map outside_dyn_map 20 28800 seconds
Crypto-map dynamic outside_dyn_map 20 kilobytes of life together - the association of safety 4608000
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 192.168.1.0 255.255.255.248 management
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 30
Console timeout 30
access to administration management
dhcpd dns 24.205.1.14 66.215.64.14
dhcpd ping_timeout 750
dhcpd field xxxxxxxx.dyndns.org
dhcpd outside auto_config
!
dhcpd manage 192.168.1.4 - 192.168.1.5
dhcpd enable management
!
dhcpd address private 192.168.10.20 - 192.168.10.30
enable private dhcpd
!
dhcpd 192.168.20.2 public address - 192.168.20.30
dhcpd enable Public
!
a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Server NTP 192.43.244.18
Server NTP 129.6.15.28
WebVPN
internal Home_VPN group strategy
attributes of Group Policy Home_VPN
value of 8.8.8.8 DNS Server 4.2.2.2
Ikev1 VPN-tunnel-Protocol without ssl-client
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Home_VPN_splitTunnelAcl
value by default-field www.xxxxxx.com
the address value IPPOOL pools
WebVPN
the value of the URL - list ClientlessBookmark
political group internal kikou
group attributes political kikou
value of 8.8.8.8 DNS Server 4.2.2.2
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list KaileY_splitTunnelAcl
XXXXXXX.dyndns.org value by default-field
username scottrog encrypted password privilege 0 xxxxxxxxxxxxxx
user_name john encrypted password privilege 0 xxxxxxxxxxxxxxx
username joek encrypted password privilege 0 xxxxxxxxxxxx
eostrike encrypted xxxxxxxxxxxx privilege 15 password username
username almostsi encrypted password privilege 0 xxxxxxxxxxxxxx
username ezdelarosa password xxxxxxxxxxxxxxencrypted privilege 0
type tunnel-group Home_VPN remote access
attributes global-tunnel-group Home_VPN
IPPOOL address pool
LOCAL authority-server-group
authorization-server-group (outside LOCAL)
Group Policy - by default-Home_VPN
authorization required
IPSec-attributes tunnel-group Home_VPN
IKEv1 pre-shared-key *.
type tunnel-group SSLClientProfile remote access
tunnel-group SSLClientProfile webvpn-attributes
enable SSLVPNClient group-alias
tunnel-group type ClientLESS remote access
tunnel-group kanazoé type remote access
attributes global-tunnel-group kanazoé
address VPN_POOL pool
by default-group-policy kikou
tunnel-group KaileY ipsec-attributes
IKEv1 pre-shared-key *.
by default-group Home_VPN tunnel-Group-map
!
!
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:438ed6084bb3dc956574b1ce83f52b86
: end
ASA5505 #.
Here are the declarations of NAT for your first question:
network object obj - 192.168.100.0
255.255.255.0 subnet 192.168.100.0
NAT (private, foreign) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 192.168.50.0 obj - 192.168.50.0
NAT (private, foreign) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 192.168.100.0 obj - 192.168.100.0
And 'clear xlate' after the above and that should fix your first question.
I would check your second question and get back to you shortly.
-
Cisco ASA 5505 unable to access the remote network
Hello
I have a Cisco ASA 5505, with 50 basic license, which is connected directly to the Modem cable with a public IP address. I have configured and active VPN on the outside interface. When connect us, we connect well without error, but we are not able to access all the resources on the remote network.
ASA IOS version 8.2 (5)
Remote IP network: 10.0.0.0/24
VPN IP Pool: 192.168.102.10 - 25
I have attached the config: llc.txt
Please let me know if you have any questions.
Thank you!
Hello
Try adding NAT 0 because inside subnet--> subnet distance
NAT (inside) 0 access-list TEST
TEST access ip 10.0.0.0 scope list allow 255.255.255.0 192.168.102.10 255.255.255.224
HTH
MS
-
Cannot access the internal network of VPN with PIX 506th
Hello
I seem to have a problem with the configuration of my PIX. I ping the VPN client from the network in-house, but cannot cannot access all the resources of the vpn client. My running configuration is the following:
Building configuration...
: Saved
:
6.3 (5) PIX version
interface ethernet0 car
Auto interface ethernet1
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate the encrypted password of N/JZnmeC2l5j3YTN
2KFQnbNIdI.2KYOU encrypted passwd
hostname SwantonFw2
domain name * *.com
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list outside_access_in allow icmp a whole
allow_ping list access permit icmp any any echo response
allow_ping list all permitted access all unreachable icmp
access-list allow_ping allow icmp all once exceed
the INSIDE-IN access list allow inside the interface tcp interface outside
list access to the INSIDE-IN permit udp any any eq field
list access to the INSIDE-IN permit tcp any any eq www
list access to the INSIDE-IN permit tcp any any eq ftp
list access to the INSIDE-IN permit icmp any any echo
the INSIDE-IN permit tcp access list everything all https eq
permit access ip 192.168.0.0 list inside_outbound_nat0_acl 255.255.255.0 192.168.240.0 255.255.255.0
swanton_splitTunnelAcl ip access list allow a whole
outside_cryptomap_dyn_20 ip access list allow any 192.168.240.0 255.255.255.0
no pager
Outside 1500 MTU
Within 1500 MTU
192.168.1.150 outside IP address 255.255.255.0
IP address inside 192.168.0.35 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP pool local VPN_Pool 192.168.240.1 - 192.168.240.254
location of PDM 0.0.0.0 255.255.255.0 outside
location of PDM 192.168.1.26 255.255.255.255 outside
location of PDM 192.168.240.0 255.255.255.0 outside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 192.168.0.0 255.255.255.0 0 0
Access-group outside_access_in in interface outside
group-access INTERIOR-IN in the interface inside
Route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.0.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20
Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-DES-MD5 value
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
client authentication card crypto outside_map LOCAL
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP identity address
part of pre authentication ISAKMP policy 20
encryption of ISAKMP policy 20
ISAKMP policy 20 md5 hash
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
Swanton vpngroup address pool VPN_Pool
vpngroup swanton 192.168.1.1 dns server
vpngroup swanton splitting swanton_splitTunnelAcl tunnel
vpngroup idle 1800 swanton-time
swanton vpngroup password *.
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 192.168.0.36 - 192.168.0.254 inside
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
dhcpd allow inside
scott hwDnqhIenLiwIr9B of encrypted privilege 15 password username
username password encrypted ET3skotcnISwb3MV privilege 2 norm
username password tarmbrecht Zre8euXN6HxXaSdE encrypted privilege 2
username, password jlillevik 9JMTvNZm3dLhQM/W encrypted privilege 2
username privilege 15 encrypted password 49ikl05C8VE6k1jG ruralogic
username bzeiter 1XjpdpkwnSENzfQ0 encrypted password privilege 2
name of user mwalla encrypted password privilege 2 l5frk9obrNMGOiOD
username heavyfab1 6.yy0ys7BifWsa9k encrypted password privilege 2
username heavyfab3 6.yy0ys7BifWsa9k encrypted password privilege 2
username heavyfab2 6.yy0ys7BifWsa9k encrypted password privilege 2
username djet encrypted password privilege 2 wj13fSF4BPQzUzB8
username, password cmorgan y/NeUfNKehh/Vzj6 encrypted privilege 2
username password cmayfield Pe/felGx7VQ3I7ls encrypted privilege 2
username privilege 2 encrypted password zQEQceRITRrO4wJa jeffg
Terminal width 80
Cryptochecksum:9005f35a85fa5fe31dab579bbb1428c8
: end
[OK]
Any help will be greatly appreciated
BJ,
You try to access resources behind the inside interface network?
IP address inside 192.168.0.35 255.255.255.0
If so, please make the following changes:
1 SWANTON_VPN_SPLIT permit access ip 192.168.0.0 list 255.255.255.0 192.168.240.0 255.255.255.0
2-no vpngroup swanton splitting swanton_splitTunnelAcl tunnel
Swanton vpngroup split tunnel SWANTON_VPN_SPLIT
outside_cryptomap_dyn_20 3-no-list of ip access allowing any 192.168.240.0 255.255.255.0
4 - isakmp nat-traversal 30
Let me know how it goes.
Portu.
Please note all useful posts
-
Cannot access the internal network with Cisco easy vpn client RV320
I have a cisco RV320 (firmware v1.1.1.06) and created a tunnel easy vpn (= split tunnel tunnel mode), then I installed the cisco client vpn v5.0.07.0290 in Windows 7 64 bit, I can connect to the vpn, but I do not see the other pc ping nor them, no idea?
Thank you
Hello
1. is the firewall on the active Windows 7 computer? If so, please disable it
2. can you check that you get a correct IP address in the range of the POOL of IP configured?
3. When you perform the tracert command to access an internal server, it crosses the VPN¨?
4. is the tunnel of split giving you access to internal IP subnets defined?
5. on the RV320 you see the user connected and sending and receiving bytes?
Don t forget to rate and score as correct the helpful post!
David Castro,
Kind regards
-
Problems connecting to the local network with NAS
So we have a private network to work. On this network we have implemented a Synology NAS. We are constantly backup of files, files, adding files, etc. updated excel... There is a lot of traffic on this subject. Recently it was kickoff of people with error messages like "Device name already in use. It could be a problem with just the NAS, but I think it might be a problem with the network or something that I could deal with different parameters. The problem occurs when there are a lot of people on the network, not necessarily work outside the SAR, which has a static IP address. Because of my ignorance of networks, I don't know what information to include to help describe the problem or put in place, so do not hesitate to ask!
Any help would be greatly appreciated, more on only an opportunity to learn more about networking is also good!
Hi Michael,
- What operating system do you use?
I suggest you to send your query to the TechNet Forum for better support.
https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=Windows10ITPro
Kind regards
-
Pavilion G6-2005ax, unable to access the wifi network
Hello
I was on WiFi from the laptop. But it does not check the Wifi Hotspots.
and even if it is true, it is impossible to connect to this Wifi network please help.
I use Windows 7 Basic.
Hello rjrocks,
Have a look here http://goo.gl/jcCqx and see if these troubleshooting steps will help solve your problem.
There are several steps here http://goo.gl/CKicD if the first document does not work.
Please let me know if this can help,
-
Unable to access the remote VPN LAN
My VPN ends very well, but cannot access the local network. The warning is the LAN is a public good 24 subnet. I'm not sure how to NAT the LAN to access the VPN subnet and not to disturb any other functionality. I have attached the configuration.
Thank you in advance.
ciscoasa # sh run
: Saved
:
ASA Version 8.2 (2)
!
ciscoasa hostname
activate the encrypted Anuj/1RTcTy/SmZO password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP address .149.200 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address *.165.37.131 255.255.255.248
!
interface Vlan5
No nameif
security-level 50
IP 10.10.10.1 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone GMT 0
standard permit access list MASTERPWRTRANS_splitTunnelAcl *. . 149.0 255.255.255.0
allow inside_nat0_outbound to access extensive ip list *. . 149.0 255.255.255.0 172.30.110.0 255.255.255.224
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
local pool POOL1 172.30.110.1 - 172.30.110.30 IP 255.255.255.224 mask
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
Global (outside) 2 *.165.37.132
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 2 *. .149.199 255.255.255.255
NAT (inside) 1 0.0.0.0 0.0.0.0
static (exterior, Interior) *. .149.199 *.165.37.132 netmask 255.255.255.255
Route outside 0.0.0.0 0.0.0.0 * 1.165.37.134
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol Server AAA MPT
AAA server MPT (inside) host .149.210
Timeout 5
key *.
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outdoors
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
Telnet *. . 149.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access insidea basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal MASTERPWRTRANS group policy
MASTERPWRTRANS group policy attributes
value of DNS server *. . 149.10 *. . 149.11
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list MASTERPWRTRANS_splitTunnelAcl
MCI.local value by default-field
ptiadmin encrypted BtOLil2gR0VaUjfX privilege 15 password username
mptadmin U2T.1fmOIe772zE username password / encrypted
type tunnel-group MASTERPWRTRANS remote access
attributes global-tunnel-group MASTERPWRTRANS
POOL1 address pool
TPM authentication server group
Group Policy - by default-MASTERPWRTRANS
IPSec-attributes tunnel-group MASTERPWRTRANS
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:820529ed70de923a8375694004b2544c
: end
ciscoasa #.The 2821 should have a route pointing to the ASA for the VPN address pool (because the ASA is not the default gateway for the LAN).
That should do it.
Federico.
-
Client remote access VPN gets connected without access to the local network
: Saved
:
ASA 1.0000 Version 2
!
hostname COL-ASA-01
domain dr.test.net
turn on i/RAo1iZPOnp/BK7 encrypted password
i/RAo1iZPOnp/BK7 encrypted passwd
names of
!
interface GigabitEthernet0/0
nameif outside
security-level 0
IP 172.32.0.11 255.255.255.0
!
interface GigabitEthernet0/1
nameif inside
security-level 100
IP 192.9.200.126 255.255.255.0
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
nameif failover
security-level 0
192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2
!
interface Management0/0
nameif management
security-level 0
192.168.2.11 IP address 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
domain dr.test.net
network of the RAVPN object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.200.0_24 object
192.168.200.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.9.200.0_24 object
192.9.200.0 subnet 255.255.255.0
the inside_network object-group network
object-network 192.9.200.0 255.255.255.0
external network object-group
host of the object-Network 172.32.0.25
Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0
access-list extended test123 permit ip host 192.168.200.1 192.9.200.190
access-list extended test123 permit ip host 192.9.200.190 192.168.200.1
access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0
192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24
pager lines 24
management of MTU 1500
Outside 1500 MTU
Within 1500 MTU
failover of MTU 1500
local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 66114.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) source Dynamics one interface
NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24
Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 outdoors
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
Terminal registration
name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI
Configure CRL
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.9.200.0 255.255.255.0 inside
Telnet timeout 30
SSH 0.0.0.0 0.0.0.0 management
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 66.35.45.128 255.255.255.192 outside
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 30
SSH version 2
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
internal RAVPN group policy
RAVPN group policy attributes
value of server WINS 192.9.200.164
value of 66.35.46.84 DNS server 66.35.47.12
VPN-filter value test123
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value test123
Dr.kligerweiss.NET value by default-field
username test encrypted password xxxxxxx
username admin password encrypted aaaaaaaaaaaa privilege 15
vpntest Delahaye of encrypted password username
type tunnel-group RAVPN remote access
attributes global-tunnel-group RAVPN
address RAVPN pool
Group Policy - by default-RAVPN
IPSec-attributes tunnel-group RAVPN
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory 2
Subscribe to alert-group configuration periodic monthly 2
daily periodic subscribe to alert-group telemetry
aes encryption password
Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea
: end
COL-ASA-01 #.
Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface
Test of Cape COLLAR-ASA-01 # sho | in 192.168.200
25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request
29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68
38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68
56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68
69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request
98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request
99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68
108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68
115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68
116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request
COL-ASA-01 #.
Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.
And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...
Hello
The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.
You can try the following changes
attributes global-tunnel-group RAVPN
No address RAVPN pool
no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool
local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask
attributes global-tunnel-group RAVPN
address RAVPN pool
no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24
In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.
the object of the LAN network
192.168.200.0 subnet 255.255.255.0
network of the VPN-POOL object
192.168.201.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL
NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.
You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.
No source (indoor, outdoor) nat Dynamics one interface
NAT source auto after (indoor, outdoor) dynamic one interface
NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections
Hope this helps
Let me know if it works for you
-Jouni
-
Ipad Cisco ipsec VPN connects but not access to the local network
Hi guys,.
I am trying to connect our ipads to vpn to access network resources. IPSec cisco ipad connects but not lan access and cannot ping anything not even not the interfaces of the router.
If I configure the vpn from cisco on a laptop, it works perfectly, I can ping all and can access resources on the local network if my guess is that the traffic is not going in the tunnel vpn between ipad and desktop.
Cisco 877.
My config is attached.
Any ideas?
Thank you
Build-in iPad-client is not useful to your configuration.
You have three options:
(1) remove the ACL of your vpn group. Without split tunneling client will work.
2) migrate legacy config crypto-map style. Here, you can use split tunneling
3) migrate AnyConnect.
The root of the problem is that the iPad Gets the split tunneling-information. But instead of control with routing traffic should pass through the window / the tunnel and which traffic is allowed without the VPN of the iPad tries to build a set of SAs for each line in your split-tunnel-ACL. But with the model-virtual, SA only is allowed.
-
ASA5505 can transfer clients to remote VPN access to the local network
I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.
Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?
These two cases are possible? :
(1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
(2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
Thank you.I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.
You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.
-
I'm portable computer maintenance of the customer, a Toshiba Satellite L305-S5885, under Vista Home Premium x 86 SP2, with infections by malicious software and internet connection problems. I have managed to get rid of all of its 251 infections and I am now addressing the connectivity problem. I'm unable to achieve on its ethernet or a wireless connection to Internet. The two network status of connections 'Unidentified network', and also ' access: Local only ' all other machines hooked up to my router via CAT5e and some via 802.11 g/n, have excellent speeds with internet connectivity, so I know that the problem is limited to his machine. I tried the following:
Deactivation and reactivation of these two connections: FAIL.
"Diagnose and repair" on the two connections: FAIL.
Under dynamic I.P. type to static/static to the dynamic: FAIL.
Uninstalled all network via Device Manager devices, then restart: FAIL.
Manually uninstalled all the drivers and utility and installed the latest versions: FAIL
The command ipconfig/all text follows:
----------------------------------------------
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.C:\Users\Brooklyn's>ipconfig/all
Windows IP configuration
Name of the host...: Brooklyns-PC
Primary Dns suffix...:
Node... type: broadcast
Active... IP routing: No.
Active... proxy WINS: No.Wireless network connection Wireless LAN adapter:
The connection-specific DNS suffix. :
... Description: Intel (r) Wireless WiFi Link 4965AGN
Physical address.... : 00-21-5C-31-87-95
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Autoconfiguration IPv4 address. . : 169.254.174.235 (Preferred)
... Subnet mask: 255.255.0.0.
... Default gateway. :
NetBIOS over TCP/IP...: enabledEthernet connection to the Local network card:
The connection-specific DNS suffix. :
Description...: Realtek RTL8102E Family PCI - E Fast Ethern
and NIC (NDIS 6.0)
Physical address.... : 00-1E-33-4E-2E-F7
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Autoconfiguration IPv4 address. . : 169.254.74.29 (Preferred)
... Subnet mask: 255.255.0.0.
... Default gateway. :
NetBIOS over TCP/IP...: enabledCard tunnel Local Area Connection * 6:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: isatap. {C41651CC-0B3D-411D-8187-745214 C 69}
B4B}
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: YesCard tunnel Local Area Connection * 11:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: isatap. {816357D 3-D 8-494C-AA09-F622AE861 44}
0FA}
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: YesCard tunnel Local Area Connection * 14:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: Teredo Tunneling Pseudo-Interface
Physical address.... : 02-00-54-55-4E-01
DHCP active...: No.
Autoconfiguration enabled...: YesC:\Users\Brooklyn's >
--------------------------------------------------Guys, I'm really hitting my head against the wall on this one, and I would be VERY happy for any help through this. Thank you!
I thought about it, there was a corrupted installation of Norton 360, the origin of the problem. I've used the Norton removal tool and voila! Internet! Thank you.
Maybe you are looking for
-
No apps on iTunes Apps Resumepage
No apps to appear on the summary page V9.3.2 Apps iTunes with my iPhone connected and synchronized to the top 6s. I can see the screens of iPhone OK on the right side of iTunes but no show of Apps on the left side. Running on my new iMac OS X 10.11
-
I have a HP Pavilion dv7-1175nr with blu - ray disc player. The player is a blu - ray movie very well to the laptop screen. However, when I connect my plasma tv 720 external resolution via hdmi port, I get an error message when you try to play blu
-
L50-B-1FU satellite do not start
When I try to turn on the laptop, it remains to be the "TOSHIBA Leading Innovation" screen for a few minutes then it gives me the possibility of "scanning and repair the drive" everything I take it gives me an error code of 0xc0000185 or says "BAD_SY
-
I have an officejet j5780 and back hinges that allow you to open the body of the printer to get to the ink cartridges came out of the upper part of the printer. How can I solve this problem? Please notify
-
PAT/NAT and VPN through a PIX
"PPTP through the PIX with Port address translation (PAT) does not work because there is no concept of ports in GRE"-this is an excerpt from a config PIX version 6.2 and below. 1. how this problem has been fixed in 6.3? GRE is encapsulated in udp or