Unable to connect to a remote server?

I've been connecting to my remote server when you use Dreamweaver for several years. Today, I received the following error message:

An FTP error occurred - cannot connect to the host.

Maximum number of users reach or not authorized to make the connection because of local firewall does not block FTP data.

My firewall is off and I can't connect to my server via Fetch.

I'm not a technical expert. Can anyone help?

Thank you

Val

Hi Val,

Please follow it mentioned below as follows:

1. exit Dw.

2. Open regedit and navigate to the following key: HKEY_CURRENT_USER\Software\Adobe\Dreamweaver CC 2015\Site préférences

3. find the DWord value: CURL_MULTI_FILES_LIMIT and set its value to 2.

4. launch Dw.

5. try FTP workflows.

Thank you

Confidante

Tags: Dreamweaver

Similar Questions

  • Windows Media Center - not the initial download put in place data for guide "unable to connect to the remote server.

    Hello

    Looking for help on this one...

    I have a new install of windows 7 pro running, and I was not able to get the guide to download Windows Media Center.   I am up-to-date with all the updates and SP1 version running.   My video card drivers are also updated.

    I use HDHOMERUN PRIME equipment with cablecard and who receives a TV signal very well and I am able to view it in WMC.    I use Verizon FIOS and my zip code is 07452.    Before this computer, I ran the cablecard even with a ceton infinitv and had no problem Guide at all.

    It's just that I can't download the guide data.  Its just totally blank.   I receive the channels and view them, but there is NO data.      Whenever I run the TV setup the same question comes up.  Cannot download the initial configuration data due to the error of previous download.   As far as I know, there is NO error message when Windows installed... actually... I reinstalled windows completely and this has not solved the problem.    I tried to manually download the guide which did not help.   It... nothing happened when I turned 'on' and 'off' WMC in Control Panel to reinstall.  I even tried explore the ehome folder and remove the file db... but nothing is helping.

    I can't find a file mcupdate.exe light on my system - don't know if this is relevant.   When I looked in the event viewer here are some of the error messages that I see.

    Impossible to extract the EpgLineups (error: unable to connect to the remote server)
    Impossible to extract the MCEClientUX (error: unable to connect to the remote server)

    I'm starting to think it's a matter of windows.   Anyone have any ideas?

    Mark

    E-mail address is removed from the privacy *.

    On Tuesday, September 23, 2014 00:32:35 + 0000, Mark_Sap_70 wrote:
     
    > I'm starting to think it's a matter of windows.   Anyone have any ideas?
     
    See this thread
     
     
     
    __________________________________________________________________________________________________
    Barb
    MVP Windows Entertainment and connected home
     
    Please mark as answer if that answers your question
     
     
     

  • Can't export virtual machines: unable to connect to the remote server

    Hello

    I'm working on vSphere client 5.1 (vCenter Server 5.1). Trying to export a virtual machine for distribution model. When I go to file-> export the template OVF..., I get the following error message:

    Can't export virtual machines: unable to connect to the remote server

    Remote not sure what/who he is not able to connect to. If I connect vSphere Web Client and navigate to the same model (or all other models), under 'All the Actions of vCenter' I don't have an option to export to the model of the FVO. But if I use a VM machine instead of a virtual machine template, I have the ability to export to the OVF, but it is grayed out.

    Am I missing any customer authorization or plugin for vShpere?

    Discovered that vSphere server had some modifications made by HIM to resolve the violation POODLE. HE had to set the ip address of the machine where export OVF will be performed. Which allowed the connection to establish vsphere client and perform an export of the FVO.

  • invoke VMScript unable to connect to the remote server

    I have two PCs, two win 7 x 64. PC1 has powercli 5.5 build 3142196 (5.5u2?) and the other who has now updated 6.0.0.7857 (last AFAIK) via VMware PowerCLI - 6.0.0 - 3205540.exe from the downloads section.

    On PC1, I can run the script

    invoke vmscript - ScriptText '(gwmi_win32_computersystem).manufacturer - like ' * vmware * "'-ToolsWaitSecs 45 - VM VMName - guestuser guestacct - guestpassword blablabla".

    and it works very well and gives me a result.

    If I run the same command on PC1, I get the error:

    Invoke-VMScript: 16/11/2015-18:32:01 VMScript Invoke cannot connect to the remote server

    on line: 1 char: 1

    + Call VMScript - ScriptText '(gwmi_win32_computersystem).manufacturer - like ' * vm...»

    + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    + CategoryInfo: NotSpecified: (:)) [invoking-VMScript], ViError)

    + FullyQualifiedErrorId: Client20_VmGuestServiceImpl_DownloadFileFromGuest_DownloadError, VMware.VimAutomation.ViCore.Cmdlets.Commands.InvokeVmScript

    Anyone encountered this before? I see no difference in the PC it would cause and I wonder if there are logs, etc. for troubleshooting, I'm not aware of. The message is a bit lacking in detail. Probably the client must connect something.

    Thank you!

    The client when you run the Invoke-VMScript cmdlet on must actually be able to connect to the physical ESXi host on which the virtual computer runs on port 443. Are two clients on the same subnet, you have a firewall between the hosts and guests? Just try to open the ESXi host welcome page in a browser from these two clients, e.g. https://myesxihost.local/

  • not be able to collect some Logs Errror: unable to connect to the remote server

    I'm trying to collect Diagnostic information requested of VMWARE and I get an error message

    Error state HOME

    Complete XX.XX.XX.xx

    Complete XX.XX.XX.xx

    YY.yy.yy.yy could not connect to the remote server

    YY.yy.yy.yy could not connect to the remote server

    Bundle of newspaper has not YY.yy.yy.yy has not generated

    VCenter Server full

    VMware Vsphere Client full

    I don't know their reasoning for this, but it seems like a pain in the thigh. Why not just export logs with the vSphere Client? File-> Export-> Export System Logs

    Or

    Use the help wizard that will allow you to collect and automatically download newspapers in vSphere?

    http://www.VMware.com/products/Datacenter-Virtualization/vCenter-support-assistant/overview.html

  • Unable to connect to a remote server with remote desktop, another machine works

    Windows XP Professional Remote Desktop connection

    Hello

    I recently bought a computer with Windows XP preinstalled Mac Professional and running Office remote version 2.1.0. I can't connect to my work server that is running Microsoft Exchange Server 2003. The most frustrating is that I also have an Air of Mac Book that has remote desktop version 2.0.1 which is able to connect. I checked I think all the security and the network settings between machines and am still unable to remedy the situation. Hoping that you may be able to guide me in the right direction.

    Thank you

    Hello lovers of Lorne.
     

    Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums as it is related to connect to the server with workstation. Appropriate in instances of Windows Server.

    Please post your question in the Windows Server forums.

  • Connect to a remote server

    I used Dreamweaver for a few years. Recently, I moved to a new computer Windows 7 OS and installed Dreamweaver again. I have regularly manage and edit a Web site without lucrative, but unable to connect to the remote server of the Web page that I used to edit the page in Dreamweaver. The site is published, the files are on my local computer and the remote server, but I can't simply connect. It gives me a msg of error without too much detail. I tried to copy the game to the top in place on my old computer to my new computer, but still cannot connect. I can't tell if it's a firewall on this new computer problem or some other thing that is specific to the operating system on the new computer, or something else entirely.

    Can you connect with an FTP 3rd party like Filezilla client?

    If not, are you sure that your server remote login credentials are correct?

    Nancy O.

  • Whenever I connect to a remote connection, I get an error message "unable to connect to this Terminal Server session remote control"

    Original title: unable to connect to this Terminal Server session remote control?

    Whenever I work with my friendly by connecting remotely, this information is pop ups as follows:

    Remote control cannot connect to this Terminal Server session. It is a known problem with Windows 2000 and XP and can occur under certain, rare conditions. To remady this situation, ask the local user switch to another session (connecting, on or off), or restart the computer.
    I know it's something related to windows authentication. But want to know in detail about this notification.
     

    Hi Victor,

    The question you posted would be better suited in the TechnNet Forums.

    I would recommend posting your thread in the link below:

    (Services Terminal Server) remote desktop services:

    http://social.technet.Microsoft.com/forums/en-us/winserverTS/threads

  • DOUBLE DB: ORA-17629: unable to connect to the remote database server

    [oracle@ora11g1 ~] $ export ORACLE_SID = sales
    [oracle@ora11g1 ~] $ rman target sys/sales@sales

    Recovery Manager: release 11.2.0.1.0 - Production Wed Jun 5 13:00:15 2013

    Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.

    connected to target database: SALES (DBID = 690066655)

    RMAN > Connect auxiliary sys/salestby2@salestby2

    connected to the auxiliary database: SALES (not mounted)

    RMAN > CURRENT SPFILE DATABASE of TARGET duplicate FOR THE EVE OF the DATABASE
    2 > DB_NAME SET = 'sales '.
    3 > SET DB_UNIQUE_NAME = "salestby2".
    4 > control_files='/u02/oradata/salestby2/control01.ctl','/u02/oradata/salestby2/control02.ctl SET'
    5 > SET DB_FILE_NAME_CONVERT = "/ u02/oradata/sales /", "/ u02/oradata/salestby2 / '.
    6 > SET LOG_FILE_NAME_CONVERT = "/ u02/oradata/sales /", "/ u02/oradata/salestby2 / ';

    From duplicate Db 5 June 13
    using the control file of the target instead of recovery catalog database
    allocated channel: ORA_AUX_DISK_1
    channel ORA_AUX_DISK_1: SID = 20 type of device = DISK

    content of Script memory:
    {
    backup that copy reuse
    TargetFile ' / auxiliary format of the u01/app/oracle/product/11.2.0/dbhome_1/dbs/orapwsales
    ' / u01/app/oracle/product/11.2.0/dbhome_1/dbs/orapwsalestby2' targetfile
    ' / u01/app/oracle/product/11.2.0/dbhome_1/dbs/spfilesales.ora' auxiliary format
    ' / u01/app/oracle/product/11.2.0/dbhome_1/dbs/spfilesalestby2.ora';
    clone of SQL 'alter system set spfile = "/u01/app/oracle/product/11.2.0/dbhome_1/dbs/spfilesalestby2.ora";
    }
    execution of Script memory

    From backup 5 June 13
    allocated channel: ORA_DISK_1
    channel ORA_DISK_1: SID = 58 type of device = DISK
    RMAN-03009: failure of the backup command on the channel ORA_DISK_1 at 05/06/2013 13:05:26
    ORA-17629: unable to connect to the remote database server
    ORA-17627: ORA-01017: name of user and password invalid. connection refused
    ORA-17629: unable to connect to the remote database server
    continue other job steps, not a not working will not re-run
    RMAN-00571: ===========================================================
    RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.
    RMAN-00571: ===========================================================
    RMAN-03002: failure of Db in dual at 05/06/2013 13:05:27
    RMAN-03015: an error has occurred in the script stored memory Script
    RMAN-03009: failure of the backup command on the channel ORA_DISK_1 at 05/06/2013 13:05:27
    ORA-17629: unable to connect to the remote database server
    ORA-17627: ORA-01017: name of user and password invalid. connection refused
    ORA-17629: unable to connect to the remote database server

    Welcome to the oracle forums!

    Please take the time to go through [url https://forums.oracle.com/forums/ann.jspa?annID=1535] FAQ PAGE

    Always after 4 version oracle numbers and details of the OS.

    Post any request outside has put between.

      \

    Tags

    Mark your questions answers if you give the answer

    Password for the SYS user on primary and standby must be the same. Copy the master password for the backup server

    SCP $ORACLE_HOME/dbs/orapwv112 : /u01/app/oracle/product/11.2/dbs/orapwdupv112

  • ORA-17629: unable to connect to the remote database server

    Hello

    I have put Dataguard in place with primary and 1 physical standby for learning/test database:

    I do NOT plan the unloading of RMAN backups on the physics of the day before.

    Recorded the primary database with RMAN and when "resync catalog db_unique_name all;" is issued.
    I get the following error:
    ---------------------------------------------------------------------------------------------------------------------
    RMAN > catalog resync db_unique_name all;
    from full resynchronization of the recovery catalog
    full complete Resync
    resynchronization of data base with DB_UNIQUE_NAME ASTTESTB
    RMAN-00571: ===========================================================
    RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.
    RMAN-00571: ===========================================================
    RMAN-03002: failed to db_unique_name resynchronization command at 28/09/2011 11:34:23
    ORA-17629: unable to connect to the remote database server
    ORA-17628: Oracle 17629 error returned by remote Oracle Server
    ------------------------------------------------------------------------------------------------------------------
    Configuration of RMAN for the main proceedings are the following:

    RMAN > show all to db_unique_name asttest;

    RMAN settings for database with db_unique_name ASTTEST are:
    CONFIGURE RETENTION POLICY TO RECOVERY OF 7-DAY WINDOW;
    CONFIGURE BACKUP OPTIMIZATION # by default
    SET UP DEFAULT DISK DEVICE TYPE; # by default
    CONFIGURE CONTROLFILE AUTOBACKUP # by default
    CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO "%F" # by default
    SET UP THE DEVICE TYPE DISK PARALLELISM 1 BACKUP BACKUPSET TYPE; # by default
    CONFIGURE BACKUP OF DATA TO DISK FILE TYPE DEVICE TO 1; # by default
    CONFIGURE BACKUP ARCHIVELOG FOR DEVICE TYPE DISK TO 1; # by default
    CONFIGURE MAXSETSIZE TO UNLIMITED; # by default
    CONFIGURE ENCRYPTION OF DATABASE # by default
    CONFIGURE THE ENCRYPTION ALGORITHM "AES128"; # by default
    CONFIGURE COMPRESSION ALGORITHM 'BASIC' AND 'DEFAULT' LIBERATION OPTIMIZE FOR TRUE LOAD; # by default
    CONFIGURE DB Nom_unique "asttest" CONNECT IDENTIFIER ' ASTTEST. UMDNJ. EDU'; _
    CONFIGURE DB "Asttestb" of nom_unique CONNECT IDENTIFIER "asttestb"; _
    CONFIGURE ARCHIVELOG DELETION POLICY TO APPLIED ON ALL STANDBY;
    CONFIGURE SNAPSHOT CONTROLFILE NAME TO ' / opt/oracle/product/11.2.0/dbhome_1/dbs/snapcf_asttest.f'; # by default

    Configuration of RMAN for instance physical standby are:

    RMAN > show all to db_unique_name asttestb;

    RMAN settings for database with db_unique_name ASTTESTB are:
    CONFIGURE RETENTION POLICY TO RECOVERY OF 7-DAY WINDOW;
    CONFIGURE BACKUP OPTIMIZATION # by default
    SET UP DEFAULT DISK DEVICE TYPE; # by default
    CONFIGURE CONTROLFILE AUTOBACKUP ON;
    CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO "%F" # by default
    SET UP THE DEVICE TYPE DISK PARALLELISM 1 BACKUP BACKUPSET TYPE; # by default
    CONFIGURE BACKUP OF DATA TO DISK FILE TYPE DEVICE TO 1; # by default
    CONFIGURE BACKUP ARCHIVELOG FOR DEVICE TYPE DISK TO 1; # by default
    CONFIGURE MAXSETSIZE TO UNLIMITED; # by default
    CONFIGURE ENCRYPTION OF DATABASE # by default
    CONFIGURE THE ENCRYPTION ALGORITHM "AES128"; # by default
    CONFIGURE COMPRESSION ALGORITHM 'BASIC' AND 'DEFAULT' LIBERATION OPTIMIZE FOR TRUE LOAD; # by default
    CONFIGURE DB Nom_unique "asttest" CONNECT IDENTIFIER ' ASTTEST. UMDNJ. EDU'; _
    CONFIGURE DB "Asttestb" of nom_unique CONNECT IDENTIFIER "asttestb"; _
    CONFIGURE ARCHIVELOG DELETION POLICY TO APPLIED ON ALL STANDBY;
    CONFIGURE SNAPSHOT CONTROLFILE NAME TO ' / opt/oracle/product/11.2.0/dbhome_1/dbs/snapcf_asttest.f'; # by default

    ----------------------------------------------------------------------------------------------------------------------

    When I tested missing missing datafile and control file scenario on the primary database, it worked (Advisor to recover data)

    However, missing datafile scenario does not work on the physics of the day before.
    Here are the steps I followed:
    ********************************************
    1 renamed a file of physical data - in standby mode:

    bash - $3.2 ls - ltr

    Total 107832

    -rw - r - 1 oracle oinstall 52429312 16 September 12:19 asttest_redo03.log

    -rw - r - 1 oracle oinstall 61874176 Sep 29 15:41 asttest_temp01.dbf

    -rw - r - 1 oracle oinstall 52436992 5 Oct 11:00 rmandg_data01.dbf

    bash - $3.2 mv rmandg_data01.dbf rmandg_data01.dbf_old

    bash - $3.2 ls - ltr

    Total 107832

    -rw - r - 1 oracle oinstall 52429312 16 September 12:19 asttest_redo03.log

    -rw - r - 1 oracle oinstall 61874176 Sep 29 15:41 asttest_temp01.dbf

    -rw - r - 1 oracle oinstall 52436992 5 Oct 11:00 rmandg_data01.dbf_old


    2. restore the datafile (find the data file # view v$ recover_file):
    RMAN > restore datafile 5;



    From restoration to 5 October 11

    Segmentation fault


    3. in spite of the error, published "recover datafile command.

    4 RMAN > recover datafile 5;



    From pick up to 5 October 11

    allocated channel: ORA_DISK_1

    channel ORA_DISK_1: SID = 10 type of device = DISK

    RMAN-00571: ===========================================================

    RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.

    RMAN-00571: ===========================================================

    RMAN-03002: failure of the command recover at 05/10/2011 12:00:40

    RMAN-06094: datafile 5 must be restored.


    5. manually copy the physical primary datafile - in standby mode, & then problem recover RMAN command:
    bash - $3.2 scp oracle@msudrainier:/ora03/oradata/asttest/rmandg_data01.dbf.

    rmandg_data01.dbf 100% 50 MB 16.7 MB/s 00:03

    bash - $3.2 ls - ltr

    Total 159096

    -rw - r - 1 oracle oinstall 52429312 16 September 12:19 asttest_redo03.log

    -rw - r - 1 oracle oinstall 61874176 Sep 29 15:41 asttest_temp01.dbf

    -rw - r - 1 oracle oinstall 52436992 5 Oct 11:49 rmandg_data01.dbf_old

    -rw - r - 1 oracle oinstall 52436992 5 Oct 12:01 rmandg_data01.dbf


    RMAN > recover datafile 5;



    From pick up to 5 October 11

    using channel ORA_DISK_1



    RMAN-00571: ===========================================================

    RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.

    RMAN-00571: ===========================================================

    RMAN-03002: failure of the command recover at 05/10/2011 12:01:59

    RMAN-06067: RECOVER the DATABASE required with a backup control file or created


    6. of course RMAN commands have failed to restore the missing data file;
    So I renamed the file to original and rebooted repeat services applies - this restore the data file and now the configuration state of the DG is normal.
    *********************************************************************************

    Not quite sure if I'm still he hands the right way or if the error above is related to RMAN not able to synchronize with the physics of the day before.

    The documentation I want to talk to is here (1 paragraph):

    [http://download.oracle.com/docs/cd/B28359_01/server.111/b28294/rman.htm#BAJDFBDD | http://download.oracle.com/docs/cd/B28359_01/server.111/b28294/rman.htm#BAJDFBDD]


    Any pointers/direction and advise is greatly appreciated.

    Best regards
    NK

    I got it!

    /home/oracle:STANDBY >$ORACLE_HOME/bin/rman target sys/ catalog /@rcatalog

Recovery Manager: Release 11.2.0.1.0 - Production on Fri Oct 7 14:12:10 2011

Copyright (c) 1982, 2009, Oracle and/or its affiliates.  All rights reserved.

connected to target database: PRIMARY (DBID=1562898590, not open)
connected to recovery catalog database

RMAN> resync catalog from db_unique_name all;

resyncing from database with DB_UNIQUE_NAME PRIMARY
starting full resync of recovery catalog
RMAN output not resynced for database with DB_UNIQUE_NAME PRIMARY
full resync complete

    If the necessary connection string a target/sys and a catalogue

    RMAN target sys / catalog /@rcatalog

    I did my standby

    Will try the primary

    Best regards

    mseberg

    Work on both. Great question!

    connected to target database: PRIMARY (DBID=1562898590)
connected to recovery catalog database

RMAN> resync catalog from db_unique_name all;

starting full resync of recovery catalog
full resync complete

resyncing from database with DB_UNIQUE_NAME STANDBY
RMAN output not resynced for database with DB_UNIQUE_NAME STANDBY

RMAN>

    Published by: mseberg on October 7, 2011 14:16

    Thanks a ton for sticking to it. I'll add this little thing to my web site.

    Published by: mseberg on October 7, 2011 14:22

  • Error message: "unable to connect to the RPC Server" and no internet connection.

    Original title: recently installed a program of pc cleaner. Seemed to really speed up my laptop that is running Windows XP.

    After two days I try to connect to the internet and no connection lie. Uninstalled the pc cleaner without problem but the problem continues to exist. All tests, etc., result in "unable to connect to the RPC server. Slide short drive and reinstall XP, are there any other things to try?

    Hi Wantamustang,

    You can try the following steps and check.

    You can set the remote procedure (RPC) call Service to start automatically:

    a. clickStart, point to settings, clickControl Paneland then double-clickServices.

    b. in theservices list, click the remote procedure (RPC) call Serviceand then clickStartup.

    c. underStartup Type, click Automaticand then click OK.

    d. restart your computer.

    You can also consult the following article:

    Windows wireless and wired network connection problems

  • CS6 Dw hangs when it is connected to a remote server

    Hi all

    First of all, thanks to all those who have contributed here I found a ton of useful info on these forums.

    I am facing a problem that has been around for awhile, but I'm afraid, I was unable to find a solution. Dreamweaver (CS6) is very slow/unresponsive in work as part of a 'Site' connected to a remote server. The weird part is that this happens only on my laptop, the feature works fine on my desktop PC which has almost identical characteristics except that my laptop is 100% SSD (you would think it would be more efficient). It hangs for a few seconds when you save a file, which IMO is acceptable, I understand that it is pushing it to the server. The real problem comes when I'm switching between open files, or open a new file. Two of these actions take about 10-15 seconds, during which Dreamweaver has a crisis and I get notification (no response) in the bar of the window.

    Dreamweaver is updated, I use no archiving/retrieval functionality. In the server settings, I have «automatically download to the server after...» "and"Maintain synchronization information"checked.  Ftp services work perfectly with my remote server, Notepad ++ also works very well.

    PC card in case it is important: (laptop is almost two years but decent hardware and short grand otherwise)

    ASUS

    Windows 10

    I7

    Samsung 500GB SSD

    8 GB RAM

    NOTE: in addition, once the file is actually opened and loaded, DW works fine; no lag, no hanging. It is the Act of switching/opening files (file at the top of DW tabs) which takes forever. Economy/downloading files takes less than 5 seconds and during this time, you see the download dialog box and DW does NOT get the "(ne répond pas) ' as it does when switching/opening files."

    Any suggestions on fixing this?

    Best regards

    Alex Overton

    Dreamweaver is designed to operate on local files that you upload to the remote server when you are finished editing the. I don't have CS6 installed, but I think he allowed you to work on individual files without defining a site beforehand, and some people used it to edit files in situs, that is what it looks like you do. It is no longer possible in Dreamweaver CM³. You must define a site to be able to edit a file.

    Dreamweaver CS6 is is no longer officially supported. If it works well otherwise, I think that you'll just have to consider this shift as a reality. You access files on a network link, so there is a latency. Why it happens on one machine but not another is a mystery.

  • Error: Unable to connect to the Converter Server

    I'm doing a P2V conversion of base with the converter for .net SDK; However I'm getting unable to connect to the converter server.  I use the SDK software on the converter server.  Any help would be greatly appreciated.

    my properties file is pretty basic:

    physicalsource.address=192.168.1.32
physicalsource.username=192.168.1.32\rootcd
physicalsource.password=**********
physicalsource.ostype=linux
physicalsource.agentport=9089
physicalsource.reboot=false
vcserver.address=192.168.80.2
vcserver.username=192.168.80.2\administrator
vcserver.password=**********
conversion.job.name=P2VConversionJob1
conversion.job.description=MyNewVMTest
conversion.vmtocreate.name=MyNewVM
conversion.vmtocreate.vcpu=1
conversion.vmtocreate.memory=4096
converterserver.address=192.168.80.5
converterserver.username=192.168.80.5\administrator
converterserver.password=**********

    Here are the results.  And I don't know what else I need included.  I disabled all firewall server at the moment as well to make sure that they weren't getting in the way.

    C:\_cd\sdk\samples\DotNet\cs\SubmitWinP2VJob\bin\Debug>ConverterSamples.exe cd.p
roperties
Caught Exception :  Name : WebException Message : Unable to connect to the remot
e server Trace :    at System.Net.HttpWebRequest.GetRequestStream(TransportConte
xt& context)
   at System.Net.HttpWebRequest.GetRequestStream()
   at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodN
ame, Object[] parameters)
   at ConverterApi.ConverterService.ConverterRetrieveServiceContent(ManagedObjec
tReference _this)
   at ConverterSamples.ConverterConnection.Connect(String serverUrl, String user
name, String password) in c:\_cd\sdk\samples\DotNet\cs\SubmitWinP2VJob\Converter
Connection.cs:line 51
ERROR: Failed to Connect to Converter Server.


C:\_cd\sdk\samples\DotNet\cs\SubmitWinP2VJob\bin\Debug>

    You must be able to connect to the computer you run the samples of the converter (192.168.80.5) on port 443 server machine. You can check the following:

    * Converter Server is running

    * There is no firewall is blocking the port 443

    * There is no other application taking port 443 and not allowing not converter tuned (a web server on the same computer?)

    * Converter server is installed in Client-Server mode (by default, it is installed in local mode only and no TCP connections are allowed, but samples SDK only support TCP mode).

  • Unable to connect to the Remote Agent of VMware Converter

    I'm trying to V2V an our old infrastructure of VMware 2.5.x our vSphere infrastructure W2K Server.

    I've done several servers of the old infrastructure without problem.

    On this particular server, however, fails with the error "Unable to connect to the Remote Agent of VMware Converter"

    The journal of the points below on the $ IFC share.

    [2011-01-14 12:32:40.008 'P2V' 4788 info] [ClientConnection, 101] Connection to IPC$ on 10.101.0.171 like 10.101.0.171\administrator
    [2011-01-14 12:33:10.086 'P2V' 4788 info] [, 0] SMB Manager: connection error for share [\\10.101.0.171\IPC$]: 1792

    [2011-01-14 12:33:10.086 'P2V' 4788 WARNING] [ClientConnection, 115] Unable to connect to IPC$ on 10.101.0.171. Reason: Error unspecified in the mechanism of the remote execution
    [2011-01-14 12:33:10.086 'P2V' 4788 info] [ClientConnection, 119] Renounce the attempt to connect to IPC$ on 10.101.0.171
    [2011-01-14 'P2V' 4788 error 12:33:10.086] [task, 295] Task failed: P2VError REMOTE_UFA_FIREWALLED (10.101.0.171)
    [2011-01-14 12:33:10.086 'P2V' 4788 verbose] [task, 339] The transition of InProgress asked congestive
    [2011-01-14 12:33:10.086 'P2V' 4788 verbose] [task, 388] Successful passage

    Any suggestions for a solution would be appreciated.

    It looks like maybe the firewall on the server. Install the converter directly on the machine you want to convert, or temporarily disable the firewall.

  • HP Envy Notebook dv6: unable to connect to the proxy server

    I saw an error message "Unable to connect to the proxy server" when I try to connect to the internet via WIFI, even if the label shows who is connected to my home router.

    HR63 wrote:

    Thanks for the tip, there is so much information, the laptop with this problem belongs to my daughter and because she doesn't have an internet connection (can not download anything), there is another way to fix it?

    I don't know because the online is where most of the instructions are locate in. I copy and paste the links here, but unless you can print them out or print the online pages it becomes hard, but here are the parts of the txt of it. +

    http://malwaretips.com/blogs/unable-to-connect-to-the-proxy-server-removal/

    How to remove "Unable to connect to the proxy server" (Virus Removal Guide)

    This page is a comprehensive guide, which will remove "Unable to connect to the proxy server" virus from your computer and any other adware program that may have been installed during the installation process.
    Please complete all of the steps in the correct order. If you have any questions or doubts in any point, STOP and ask for our assistance.
    STEP 1: restore the default proxy to your machine settings
    STEP 2: remove failed to connect to the ad software proxy server from Internet Explorer, Firefox and Google Chrome with AdwCleaner
    STEP 3: delete impossible to connect to the proxy server with Junkware Removal Tool browser hijacker
    STEP 4: delete impossible to connect to the virus pop up server proxy with Malwarebytes Anti-Malware free
    STEP 5: check a second time for the "unable to connect to the proxy server" malware with HitmanPro
    (Optional) STEP 6: delete impossible to connect to the proxy server of Internet Explorer, Firefox and Google Chrome ads

    http://www.geckoandfly.com/9275/Internet-connection-error-unable-to-connect-to-the-proxy-server/

    It is with IE

    Step 1 - launch Internet Explorer

    Step 2 - Click the icon "but" it looks like a gear wheel...

    Step 3 - select 'Internet Options '.

    Step 4 - Select the 'connection '.

    Step 5 - Click Lan settings

    Step 6 - uncheck "use a proxy server for your LAN (these settings may not apply to dial-up or VPN connections)."

    Step 7 - click 'Ok' to save the changes

    If you are using a proxy server, check your proxy settings, or check with your network administrator to make sure that the proxy server is running. If you don't believe that you should use a proxy server. Here's a video tutorial:

    Also, if you can since I don't remember which browser your help that gave you this message that I had to go with IE as a default.

Maybe you are looking for

  • Re: Difference between the NB250-108 and NB510-11U?

    Hello I have a NB250-108, which was improved in RAM 2 1 (sorry I am garbage to techy stuff) as a friend suggested he could accelerate his top. (makes) I had a few years now and the battery is not coterminous with and I have problems with the load as

  • Windows encountered a problem when you try to copy a file___

    Ideas: suggestions; try to copy the files-error message, cannot copy on disk You have problems with programs Error messages Recent changes to your computer What you have already tried to solve the problem Remember - this is a public forum so never po

  • NET framework, why I so much?

    I think I have every available version of net framework. What are they and I need to so many different versions for vista?

  • CSM and existing VPN tunnels

    I ran into an issue in the past. When you install the CSM for the first time in an environment where there is an existing VPN network, the product will not reflect existing VPN tunnels in the map view. I tried to import existing configurations using

  • Width if Sidebar area

    HelloI'm on version 4.1.1.00.23 of the Apex.  I have a page where I use several parts of the sidebar on the entire page. I would like to extend the width of the sidebar regions. How can I do this? Let me know if youneed more details.Thank youPAM