Unable to connect to remote vpn IPSec (Error 412)
Hello
Try to configure the IPSec vpn connection but error 412: the remote peer not responding.
Router Cisco is directly connected to the internet using the dialer interface.
So far, I tried the following:
Disabled Windows Firewall
IPSec over TCP ticket (received error 414)
Permit to debug crypto ISAKMP and IPSEC (no illustrated newspaper)
Newspapers enabled on the version of client VPN 5.0.01.0440
(Impossible to establish Phase 1 SA with server 'xxxxxxxxx' due to the 'DEL_REASON_PEER_NOT_RESPONDING')
The router configuration:
version 12.4
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
!
boot-start-marker
boot-end-marker
!
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login usr_auth local
AAA authorization grp_auth LAN
!
AAA - the id of the joint session
!
resources policy
!
MMI-60 polling interval
No mmi self-configuring
No pvc mmi
MMI snmp-timeout 180
IP subnet zero
no ip source route
IP cef
!
!
No dhcp use connected vrf ip
DHCP excluded-address IP 192.168.3.1 192.168.3.10
!
pool IP dhcp pool Classes
network 192.168.3.0 255.255.255.0
default router 192.168.3.1
Server DNS XXXXXX xxxxxxxxxxx
!
!
no ip bootp Server
no ip domain search
IP domain name xxxxxxxxx
property intellectual ssh time 80
VPDN enable
!
!
!
!
!
username 7 password xxxxxx xxxxx
!
!
!
crypto ISAKMP policy 10
BA aes
preshared authentication
Group 5
!
ISAKMP crypto client configuration group client_cfg
XXXXXXX key
DNS xxxxxxx
pool vpn_pool
ACL 120
Max-users 2
Profile of isakmp crypto vpn-ike-profile-1
client_cfg group identity match
client authentication list usr_auth
ISAKMP authorization list grp_auth
client configuration address respond
virtual-model 2
!
!
Crypto ipsec transform-set encrypt-method-1 esp - aes esp-sha-hmac
!
Crypto ipsec VPN-profile-1 profile
the transform-set encrypt-method-1 value
!
!
!
!
interface Loopback0
the IP 10.0.0.1 255.255.255.0
!
ATM0 interface
no ip address
No atm ilmi-keepalive
DSL-automatic operation mode
!
point-to-point interface ATM0.1
no link-status of snmp trap
PVC 8/35
PPPoE-client dial-pool-number 1
!
!
interface FastEthernet0
no ip address
automatic speed
!
interface FastEthernet1
Shutdown
!
interface FastEthernet2
switchport access vlan 2
!
interface FastEthernet3
switchport access vlan 3
!
interface FastEthernet4
switchport access vlan 4
half duplex
!
tunnel type of interface virtual-Template2
IP unnumbered Loopback0
IP nat inside
IP virtual-reassembly
ipv4 ipsec tunnel mode
Profile of tunnel ipsec VPN-profile-1 protection
!
interface Vlan1
no ip address
!
interface Vlan2
192.168.1.100 IP address 255.255.255.0
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1452
!
interface Vlan3
address 192.168.3.1 IP 255.255.255.0
IP access-group 101 in
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1452
!
interface Vlan4
192.168.4.1 IP address 255.255.255.0
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1452
!
interface Dialer1
the negotiated IP address
IP mtu 1492
NAT outside IP
IP virtual-reassembly
encapsulation ppp
Dialer pool 1
Dialer-Group 1
PPP authentication pap callin
PPP pap sent-name of user password xxxxxx xxxxxxx 7
!
local pool 10.0.0.10 IP vpn_pool 10.0.0.20
IP classless
IP route 0.0.0.0 0.0.0.0 Dialer1
!
no ip address of the http server
no ip http secure server
the IP nat inside source 1 list overload of the Dialer1 interface
IP nat inside source static tcp 192.168.1.1 25 25 Dialer1 interface
IP nat inside source static tcp 192.168.1.1 80 80 Dialer1 interface
IP nat inside source static udp 192.168.1.1 53 53 Dialer1 interface
IP nat inside source static tcp 192.168.1.1 53 53 Dialer1 interface
IP nat inside source static tcp 192.168.1.1 interface 1000 Dialer1 1000
IP nat inside source static tcp 192.168.1.1 interface 443 443 Dialer1
IP nat inside source static tcp 192.168.1.1 interface Dialer1 143 143
!
WAN-IN extended IP access list
refuse the ip 0.0.0.0 0.255.255.255 everything
deny ip 10.0.0.0 0.255.255.255 everything
deny ip 100.64.0.0 0.63.255.255 all
deny ip 127.0.0.0 0.255.255.255 everything
deny ip 169.254.0.0 0.0.255.255 everything
deny ip 172.16.0.0 0.15.255.255 all
deny ip 192.0.0.0 0.0.0.255 any
deny ip 192.0.2.0 0.0.0.255 any
deny ip 192.168.0.0 0.0.255.255 everything
deny ip 198.18.0.0 0.1.255.255 all
deny ip 198.51.100.0 0.0.0.255 any
deny ip 203.0.113.0 0.0.0.255 any
refuse the 224.0.0.0 ip 31.255.255.255 all
allow an ip
!
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit 192.168.3.0 0.0.0.255
access-list 1 permit 192.168.4.0 0.0.0.255
access-list 101 deny ip 192.168.3.0 0.0.0.255 192.168.1.0 0.0.0.255
access list 101 ip allow a whole
access ip-list 120 allow a whole
!
control plan
!
!
Line con 0
exec-timeout 5 0
line to 0
exec-timeout 5 0
password 7 xxxxxxxxxxxx
line vty 0 4
exec-timeout 5 0
password 7 xxxxxxxxxxxx
preferred transport ssh
entry ssh transport
line vty 5 15
exec-timeout 5 0
password 7 xxxxxxxxxxxx
preferred transport ssh
entry ssh transport
!
end
I don't get any password prompt, so I guess there is a misconfiguration. Would appreciate if you can help with this.
Thank you
The 10.0.0.x pool is configured properly. Just change the NAT to traffic between 192.168.1.x, 3.x, and 4.x are exempt in NAT, where the above change config.
Your split tunnel ACL says allow an entire ip, so please change it to the following:
access-list 120 allow ip 192.168.1.0 0.0.0.255 10.0.0.0 0.0.0.255
access-list 120 allow ip 192.168.3.0 0.0.0.255 10.0.0.0 0.0.0.255
access-list 120 allow ip 192.168.4.0 0.0.0.255 10.0.0.0 0.0.0.255
Tags: Cisco Security
Similar Questions
-
Unable to connect to the VPN, get error 800, communication
I am trying to set up a connection to a VPN, get this error 800:
The remote connection has not been because attempts VPN tunnels failed. The VPN server is maybe inaccessible. If this connection tries to use an L2TP/IPsec tunnel, the required security settings for IPsec negotiation is may not be configured correctly.
Hello
Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Forum. You can follow the link to your question:
http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads -
Unable to connect to remote PowerShell and get error message.
I have two computer to Windows 7.
Unable to connect to remote PowerShell and this error message
nvoke-command - computername XXXXXX - scriptblock {}
get-process} - administrator credentials
[XXXXXXX] failed to connect to the remote server XXXXXX with the
error message: WinRM client cannot process the request. If the
authentication scheme is different from Kerberos, or if the client computer is
not joined to a domain, then HTTPS transport must be used or the destination
machine must be added to the TrustedHosts configuration. Use winrm.cmd
to configure TrustedHosts. Note that computers in the TrustedHosts list might
do not be authenticated. You can get more information about it by running the
following command: winrm help config. For more information, see the
about_Remote_Troubleshooting help topic.
+ CategoryInfo: OpenError: [XXXXXX], PSRemotingT
ransportException
+ FullyQualifiedErrorId: ServerNotTrusted, PSSessionStateBroken
PS C:\windows\system32 >PS C:\Users\Administrator > Invoke-Command - ComputerName XXXX - ScriptBlock {get-process} - administrator credentials
[XXXXXX] failed to connect to the remote server XXXXX with the following
error message: the client cannot connect to the specified destination in the
request. Verify that the service on the destination is running and that he accepts the
applications. Consult the logs and documentation for running management service
on the destination, most IIS or WinRM. If the destination is the WinRM
service, run the following command on the destination to analyze and configure the
WinRM service: "winrm quickconfig". For more information, see the
about_Remote_Troubleshooting help topic.
+ CategoryInfo: OpenError: (XXXXX:String)], PSRemotingTranspo
rtException
+ FullyQualifiedErrorId: CannotConnect, PSSessionStateBroken# Outgoing connection is fine because I can connect to a different machine here. However incoming connection does not work
# Tried several things like "Enable-PSRemoting - Force." and it starts Properperly
# And since I put the machine in workgroup, as well run "Set-Item WSMan: \localhost\Client\TrustedHosts * ' (it is running successfully as well)
# Infact WinRM QuickConfig will not work.
# And tried with and without firewall. and also applied several patches, but has not solved the problem
Please notify
Original title: WinRM
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
If you give us a link to the new thread we can point to some resources it -
Original title: unable to connect to the internet
Whenever I connect to my computer and get it on my desk, it goes on to say that Cisco AnyConnect VPN Service not available. How can I fix? I am not connected to the internet and I can't connect to the internet as well. He said also Cisco AnyConnect VPN service agent is not an answer. Please restart this application after a minute. Also, I can't use my firewall for some reason, if I try to allow its loading and the greenbar's going that far - then stops and says that there is an error. I forgot where I tried to activate.
Oh thanks for the help but I fix it myself. I just did a system restore to a month before
-
I can not connect from home (Windows 7 Starter Edition) at the office of the wife (WinXP Home) via a VPN connection.
Follow-up of the installation a new connection wizard. Unable to connect with the new account (done in the vpn Wizard. Unable to connect with an existing account on the server VPN system either. I am able to connect from another system of home to the system that hosts the server VPN using pcAnywhere.
Or the other attempt gives an error 800 - VPN tunnel failed.
Any ideas on where to start looking?
I can not connect from home (Windows 7 Starter Edition) at the office of the wife (WinXP Home) via a VPN connection.
Follow-up of the installation a new connection wizard. Unable to connect with the new account (done in the vpn Wizard. Unable to connect with an existing account on the server VPN system either. I am able to connect from another system of home to the system that hosts the server VPN using pcAnywhere.
Or the other attempt gives an error 800 - VPN tunnel failed.
Any ideas on where to start looking?
See this section of the RRAS team blog...
http://blogs.technet.com/rrasblog/archive/2009/08/12/troubleshooting-common-VPN-related-errors.aspx
More than likely the XP box is behind a firewall/router which does not pass traffic GRE protocol 47 . You can test the VPN PPTP link by running the test detailed in the traffic VPN PPTP Ping and secitons on this page.
http://TechNet.Microsoft.com/en-us/library/bb877965.aspx
GRAP the pptpsrv.exe and pptpclnt.exe programs on the internet or from a CD of XP SP2. If the tests fail work arounds include...
* Update the firmware on the router to a version known to pass traffic GRE protocol 47.
* Flashing the router, if supported, with third-party firmware like DD - WRT that supports passing traffic GRE protocol 47.
* Buying a router known to pass the GRE protocol traffic.
* Use an alternative such as Secure Shell [SSH] and a free SFTP client such as WinSCP or TBM for secure remote access to files and folders or Remote Desktop/access control to computers on office's LAN.
MS - MVP Windows Desktop Experience, "when everything has failed, read the operating instructions. -
Easy remote VPN - IPsec Session count
I have recently updated our ASA5510 head to our datacenter to 8.2.1 to 8.4.5. The ASD has been also improved 6.2.1 to 7.1. (1) 52. Under the old code, a connected remote ASA5505 via remote VPN easy showed 1 IPsec tunnel. However, after the upgrade, it shows 42 sessions. It seems to me that each split tunnel network defined in the easy VPN profile is being counted as a tunnel. Someone has seen this, or is - it possible that I may have something misconfigured now that the code is upgraded? Thank you.
Dave
No, IMHO, it's a display error in ASDM for 7.1.
Return to ASDM 6.4.9 and it should be 1 tunnel.
-
"Unable to connect to the Skype server" error on samsung wave 723
I got Skype Lite (or the Java thing, whatever we call it - does not allow calls - only CAT) on my Samsung Wave 723 for more than six months. Earlier this week he suddenly disconnected me and when I tried to log in again it showed this error "Unable to connect to the server of Skype." almost immediately after, I started signing in. I tried to reset the settings in Skype, my phone settings, I took out the battery and reset even WiFi. Then I tried to connect with a few other WiFis - still the same error. My friend has the same version of Skype Lite on his cell phone, and it works very well and without errors.
Anyone know how to fix this error? It is urgent, please.
Solved the problem on my phone. I just had to add the area code to my phone number in the connection menu.
@yousef8824: I downloaded my Skype Java one of those ages of links it is a. not useful at this time.
-
Windows 7 not connecting to the VPN - gives error 930
I'm one of my boxes, upgrade to Windows 7 (x 64) and everything seems to work - until I try to connect to my VPN - it gives me an Error 930. On the same home network are a (x 64) Vista and XP (x 86) - both can make the VPN connection without problem to the same location. When this box is Vista, it has good work as well.
There is nothing fancy here - simple Windows work stations at a location behind a Linksys WRT54GS connection to a Windows Server 2003 server behind an ISA firewall.
I deleted the connection and recreated, and it worked. What is interesting is that the first connector name was identical to the location I tried to connect to (internal & external). When I change the name of the connector, everything worked.
To test, I deleted this connection and created another one as the first - named the same as the network tried to connect to and it wrong on. When I renamed the connection, everything worked perfectly. It seems that Windows 7 is lost when you name the connector, the same as the destination network FULL domain name.
-
Unable to access the remote VPN LAN
My VPN ends very well, but cannot access the local network. The warning is the LAN is a public good 24 subnet. I'm not sure how to NAT the LAN to access the VPN subnet and not to disturb any other functionality. I have attached the configuration.
Thank you in advance.
ciscoasa # sh run
: Saved
:
ASA Version 8.2 (2)
!
ciscoasa hostname
activate the encrypted Anuj/1RTcTy/SmZO password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
IP address .149.200 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address *.165.37.131 255.255.255.248
!
interface Vlan5
No nameif
security-level 50
IP 10.10.10.1 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone GMT 0
standard permit access list MASTERPWRTRANS_splitTunnelAcl *. . 149.0 255.255.255.0
allow inside_nat0_outbound to access extensive ip list *. . 149.0 255.255.255.0 172.30.110.0 255.255.255.224
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
local pool POOL1 172.30.110.1 - 172.30.110.30 IP 255.255.255.224 mask
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
Global (outside) 2 *.165.37.132
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 2 *. .149.199 255.255.255.255
NAT (inside) 1 0.0.0.0 0.0.0.0
static (exterior, Interior) *. .149.199 *.165.37.132 netmask 255.255.255.255
Route outside 0.0.0.0 0.0.0.0 * 1.165.37.134
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
RADIUS protocol Server AAA MPT
AAA server MPT (inside) host .149.210
Timeout 5
key *.
AAA authentication enable LOCAL console
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 outdoors
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400
Telnet *. . 149.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access insidea basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal MASTERPWRTRANS group policy
MASTERPWRTRANS group policy attributes
value of DNS server *. . 149.10 *. . 149.11
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list MASTERPWRTRANS_splitTunnelAcl
MCI.local value by default-field
ptiadmin encrypted BtOLil2gR0VaUjfX privilege 15 password username
mptadmin U2T.1fmOIe772zE username password / encrypted
type tunnel-group MASTERPWRTRANS remote access
attributes global-tunnel-group MASTERPWRTRANS
POOL1 address pool
TPM authentication server group
Group Policy - by default-MASTERPWRTRANS
IPSec-attributes tunnel-group MASTERPWRTRANS
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:820529ed70de923a8375694004b2544c
: end
ciscoasa #.The 2821 should have a route pointing to the ASA for the VPN address pool (because the ASA is not the default gateway for the LAN).
That should do it.
Federico.
-
Unable to connect to the server Essbase (error #1051293)
Hello
Using Essbase Integration Services Consol, I created a template OLAP, and then click OLAP Metaoutline and even checked. But when I tried to load the members and the data I just had an error that is "unable to connect to the Essbase server: Localhost (error #1051293).
If any of you have solution for this issue, so kindly help me.
Saami
Do you know who your security Admin? Or at least you have access to Shared service URL?
In LDAP, type your user ID and you see your start-up. Add the new app to your user ID, and you define.
-
Unable to connect to the host. Error: The specified version is not found
vmrun-t esx h https://192.168.1.123/SDK u root Pei password list
Unable to connect to the host.
Error: The specified version is not found
Any ideas why it does not work? It is run on a Windows XP workstation. The target server is on the local network and running ESXi 4.1. The vmRun version is 7.1.2 and is installed with Workstation 7.1.2.
I also tried Ubuntu 10.04 with vmRun from a Workstation 7.1.2 installation. There, he also fails with the same error.
Note that ESXi 4.1 is used to test installation is not allowed and is running in demo mode. Management of the vSphere client works without any problem the same Windows XP workstation.
Any help would be appreciated. Thank you.
You must install the full package of VIX by http://communities.vmware.com/community/developer/downloads. It contains only components to manage the workstation. Please note that I had to install in the VIX 1.10.1 order then Workstation 7.1.2 to get both to work on my Windows 7 computer.
-
RRAS issues! -Unable to connect to the VPN users,
original title: RRAS issues!
Hi all, I have some real issues with my RRAS VPN. All of a sudden the users are randomly cannot connect to the VPN. Making mistakes like 619 800 and so on. I activated the GRE (once the problem starts) checked to see if the 1723 port is open. Why is this happening now?
I use DynDns host name and everything seems fine, fact that there are enough ports available to PPTP on the RRAS.
I am running Windows 2003 SBS SP2
Router is a MAKO 6861 with a normal ADSL line
I see this in the PPP.log:
[8128] 06-04 10:27:27:794: Recv timeout event received for portid = 288, Id = 5, Protocol c021, fAuth = 0 =
[8128] 06-04 10:27:27:794:
[8128] 06-04 10:27:27:794:
[8128] 10:27:27:794:
[8128] 10:27:27:794: <06 57="" eb="" 0d="" 3e="" 07="" 02="" 08="" 02="" 0d="" 03="" 06="" 11="" 04="" 06="" 4e="" |.w..="">... N |
[8128] 10:27:27:794:<13 17="" 01="" b0="" 09="" a5="" e1="" 15="" e6="" 49="" 4f="" 85="" fb="" 7c="" a0="" 15="">13>
[8128] 10:27:27:794:And some of this:
[8128] 06-04 10:27:43:325: line before the end event occurred on port 138
[8128] 10:27:43:325 06-04: FsmDown event is received for Protocol c021 on port 138
[8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 9, Protocol is c021, EventType = 0, = 0 fAuth
[8128] 10:27:43:325 06-04: FsmReset called Protocol c021, port = 138 =
[8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, = 0 protocol, EventType = 3, fAuth = 0
[8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, = 0 protocol, EventType = 7, fAuth = 0
[8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, = 0 protocol, EventType = 2, fAuth = 0
[8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, = 0 protocol, EventType = 1, = 0 fAuth
[8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, = 0 protocol, EventType = 4, = 0 fAuth
[8128] 10:27:43:325 06-04: RemoveFromTimerQ called portid = 288, Id = 0, Protocol is c029, EventType = 0, = 0 fAuth
[8128] 06-04 10:27:43:325: LcpEnd
[8128] 06-04 10:27:43:325: line Post event took place on the port 138
[8128] 06-04 10:27:43:325: NotifyCaller (hPort = 138, dwMsgId = 23)
[8128] 06-04 10:27:48:043: line-up event took place on the port 138
[8128] 06-04 10:27:48:043: PortName: VPN3-19
[8128] 06-04 10:27:48:043: from PPP link with IfType = 0x0, 1p1f = 0 x 0, IPXIf = 0 x 0
[8128] 10:27:48:043 06-04: RasGetBuffer returned 58 c 2148 to SendBuf
[8128] 10:27:48:043 06-04: FsmInit called Protocol c021, port = 138 =
[8128] 06-04 10:27:48:043: ConfigInfo = 80260
[8128] 06-04 10:27:48:043: available APs = 2
[8128] 10:27:48:043 06-04: FsmReset called Protocol c021, port = 138 =Hello
Your question of Windows Server is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public.
Please ask your question in the Technet Windows Server General category.
06>
http://social.technet.Microsoft.com/forums/en-us/winservergen/threads -
Original title: Unable to connect to the wireless network
Unable to connect to the network wireless Toshiba Satellite A105 PC running Windows 7. "Windows could not finish repairing the problem because it is impossible to perform the following action. Renewal of your IP address. Works with Windows XP SP2, IE 8.00.6001.18702 file, I think that Version 3. It has been installed on a disk provided by Microsoft after that old installation became corrupt (in the sense of Microsoft technical support.) Before that, wireless network worked well. (So unable to connect to the Internet for updates.) Have tried to change the other settings and different messages acquired when it SHOWS that I am connected but cannot connect because of something to do with the certificate. I don't remember what I did to try to solve this problem in the last days.
I should add that I have tried the solutions of the previous forum on this topic, and none worked.Hi Marilynnla,
Sorry to hear about the bad experience you encounter. Lets see if the network problem can somehow be archived.
Read this article and follow the steps. Lets see if it helps in any way.
How to troubleshoot wireless network connections in Windows XP Service Pack 2(Works for Windows XP SP3 as well)
-
Unable to connect to the Internet, receive error message: DEBUGER END WIRE.
Original title: unable to connect to the Internet
Hello
I am using Dell inspiron 1525 with Win.Vista Home Premium 32 bit
When I connect to internet I displays message DEBUGER CANCEL THREAD
There is no driver problem
Someone help me
I thank & regard
Satish Baker
Hi Sissi,
1. you are using a wired or wireless?
2. do you and changes to the network card or manually change all the settings?
3 when was the last time it worked?
4. are you tring to set up internet connection in windows vista for the first time?
Please follow the links below to solve the problem.
Windows wireless and wired network connection problems
See also this: the problems of Internet connection
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems
I hope this helps!
-
Recently, I upgraded my windows vista business to windows 7 Professional and can not connect to the VPN. When I did a search on the internet I found that this could be because of the mistake of sstp WAN Miniport. Windows has the drivers for it?
VijayOriginal title: miniport network driver extended WAN sstpHi Vijay,
You can view this issue in the Forums of TechNet Windows 7 IT Pro: http://social.technet.microsoft.com/Forums/en/category/w7itpro/
Thank you.
Maybe you are looking for
-
iPod Touch software update?
My iPod Touch model MC544LL/A software iOS 6.1.6 is A software update is available? Specifically, I want to run the actual application of the MLB AtBat on that. Possible? Thank you.
-
Satellite A210-17R: power management automatically changes to the default settings
Hello I have a Satellite A210-17R with Win XP SP2. Works pretty well, except for the power management settings (they might call energy Mgmt., I don't know, cause Im using a German language version, so all the terms I use are translated from German).
-
Don't want to use my flash as a slave.
I want to use my 430 ex ii on my Canon 7 d mk ii, can I disable my popup flash forever?
-
Windows vista will not load or run.
on startup, I get a repar recovery option. I hit that and nothing happens but a blue screen. I don't have to restar windows wndowsdisk. what I can do. cant it be started
-
HP dv7 notebook doesn't bootup produces WA794UAWABA CNF0071KVT
Cannot start Windows 1. Insert Windows installation disc and restart your computer (I have not) 2. choose your language settings, and then click Next 3. click on "repair your computer". Status: 0x000000f Info: the boot selection failed because a requ